Installation & Assembly

CAUTION – RISK OF SHOCK –
Disconnect Power at the main circuit breaker panel or main
fusebox before starting and during the installation.
3) Make wire connections. Reference chart below for correct con-
nections and wire accordingly.
4) Carefullypushxture[4] to wall making sure all connections
remain secure and wires do not get pinched.
5) Insert and tighten mounting screws[5]tosecureFixture[4] to
wall.
INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS
AND/OR IN WET LOCATIONS.
6) Mountingsurfaceshouldbeclean,dry,atand1/4”larger
that the canopy on all sides. Any gaps between the mounting
surfaceandcanopyexceeding3/16”shouldbecorrectedas
required.
7) With silicone caulking compound, caulk completely around
where back of canopy meets the wall surface to prevent water
fromseepingintooutletbox.
WARNING:
Thisxtureisintendedforinstallationinaccordancewiththe
NationalElectricalCode(NEC)andalllocalcodespecications.
If you are not familiar with code requirements, installation by a
certiedelectricianisrecommended.
CLEANING:
Always be certain that electric current is turned off before cleaning.
Only a damp cloth should be used. Harsh cleaning products may
damagethenish.
FCC INFORMATION:
Thisdevicecomplieswithpart15oftheFCCRules.Operationis
subject to the following two conditions:
(1) Thisdevicemaynotcauseharmfulinterference,and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the
limitsforaClassBdigitaldevice,pursuanttopart15oftheFCC
Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following mea-
sures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
INSTALLATION:
• Read and understand all instructions and illustrations completely
beforeproceedingwithassemblyandinstallationofxture.
• Ifyouhaveanydoubtsabouthowtoinstallthisxture,orifthe
xturefailstooperatecompletely,pleasecontactaqualied
electrician.
• All parts must be used as indicated in the instructions. Do not
substitute any parts, leave parts out, or use any parts that are
worn or broken. Failure to obey this instruction could invalidate
theULlisting,C.S.A.certication,and/orETLlistingofthis
xture.
• Fixtureistobeconnectedtoasinglebranchcircuit.
• Mountingsurfaceshouldbeclean,dry,atand1/4”largerthan
thexturehousingsurface.
Instructions
1) Attachthemountingplate[1]totheoutletbox[2] with supplied
screws[3]. NOTE: The mounting plate[1] must be mounted
withthexturethreadedmountingholesmatchingmounting
holesonxture[4].
2) Grounding instructions: (See Illus. A or B).
 A) Onxtureswheremountingstrapisprovidedwithahole
andtworaiseddimples.Wrapgroundwirefromoutletbox
around green ground screw, and thread into hole.
 B) Onxtureswhereacuppedwasherisprovided.Attach
 groundwirefromoutletboxundercuppedwasherand
green ground screw, and thread into mounting strap.
 Ifxtureisprovidedwithgroundwire.Connectxtureground
wiretooutletboxgroundwirewithwireconnector.(Notpro-
vided.) After following the above steps. Never connect ground
wire to black or white power supply wires.
GREEN GROUND
SCREW
CUPPED
WASHER
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
A
B
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire