Installation & Assembly

12) Raise canopy to ceiling.
13) Secure canopy in place by tightening threaded ring onto
screw collar loop.
14) Thread hexnut onto end of threaded pipe. Thread that end of
threaded pipe into bottom of fixture body.
15) Slip bottom trim over end of threaded pipe.
16) Thread finial onto end of threaded pipe. (DO NOT over
tighten.)
17) Set glass down over socket.
18) Thread socket ring onto socket. Tighten socket ring to
secure glass in place. (DO NOT over tighten.)
1) Pass fixture wire from fixture body through the loop. Thread
the loop onto the top of the fixture body.
2) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
3) Take threaded pipe from parts bag and screw in screw collar
loop a minimum of 6 mm (1/4”). Lock into place with hexnut.
4) Run another hexnut down threaded pipe almost touching
first hexnut. Now screw threaded pipe into mounting strap.
Mounting strap must be positioned with extruded thread
faced into outlet box. Threaded pipe must protrude out the
back of mounting strap. Screw third hexnut onto end of
threaded pipe protruding from back of mounting strap.
5) Connect mounting strap to outlet box.
6) Unscrew the threaded ring from screw collar loop. Take
canopy and pass over screw collar loop. Approximately one
half of the screw collar loop exterior threads should be
exposed. Adjust screw collar loop by turning assembly up or
down in mounting strap. Remove canopy.
7) After desired position is found, tighten both top and bottom
hexnuts up against the bottom and top of the mounting
strap.
8) Slip canopy over screw collar loop and thread on threaded
ring. Attach chain (with fixture connected) to bottom of
screw collar loop. Unscrew threaded ring, let canopy and
threaded ring slip down.
9) Weave electrical wire and ground wire through chain links no
more than 3 inches apart. Pass wire through threaded ring,
canopy, screw collar loop, threaded pipe and into outlet box.
10) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into
mounting strap.
If fixture is provided with ground wire (thin silver wire).
Connect fixture ground wire (thin silver wire) to outlet box
ground wire with wire connector (not provided.) after
following the above steps. Never connect ground wire to
black or white power supply wires.
11) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
MOUNTING STRAP
ABRAZADERA DE MONTAJE
HEXNUT
TUERCA HEXAGONAL
THREADED PIPE
TUBO ROSCADO
CANOPY
ESCUDETE
THREADED RING
ANILLO ROSCADO
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
SCREW COLLAR LOOP
OJAL DE COLLAR
ROSCADO
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
LOOP
ANILLO
FIXTURE BODY
CUERPO DEL ARTEFACTO
GLASS
VIDRIO
SOCKET RING
ANILLO DEL
CASQUILLO
HEXNUT
TUERCA HEXAGONAL
THREADED PIPE
TUBO ROSCADO
BOTTOM TRIM
GUARNICIÓN INFERIOR
FINIAL
CAPUCHON