OM-237 881J 2011−09 Processes Multiprocess Welding Description Arc Welding Power Source EXTREME 360 MAP Auto-Line ™ File: MULTIPROCESS
TABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3.
TABLE OF CONTENTS SECTION 8 − SMAW/CAC-A OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1. Typical Connection For SMAW And CAC-A Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2. CC Welding Mode - SMAW/CAC-A Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3. Stick Welding Mode - SMAW/CAC-A Process . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som 2011−01 7 Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage DANGER! − Indicates a hazardous situation which, if not avoided, will result in death or serious injury. The possible hazards are shown in the adjoining symbols or explained in the text. Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
FUMES AND GASES can be hazardous. Welding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health. D Keep your head out of the fumes. Do not breathe the fumes. D If inside, ventilate the area and/or use local forced ventilation at the arc to remove welding fumes and gases. D If ventilation is poor, wear an approved air-supplied respirator.
1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over, or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit. FALLING EQUIPMENT can injure. D Use lifting eye to lift unit only, NOT running gear, gas cylinders, or any other accessories.
1-4. California Proposition 65 Warnings Welding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code Section 25249.5 et seq.) Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION fre_som_2010−03 7 Se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes. 2-1. Symboles utilisés DANGER! − Indique une situation dangereuse qui si on l’évite pas peut donner la mort ou des blessures graves. Les dangers possibles sont montrés par les symboles joints ou sont expliqués dans le texte. Indique une situation dangereuse qui si on l’évite pas peut donner la mort ou des blessures graves.
Il reste une TENSION DC NON NÉGLIGEABLE dans les sources de soudage onduleur UNE FOIS l’alimentation coupée. D Arrêter les convertisseurs, débrancher le courant électrique et décharger les condensateurs d’alimentation selon les instructions indiquées dans la partie Entretien avant de toucher les pièces. LES PIÈCES CHAUDES peuvent provoquer des brûlures. D Ne pas toucher à mains nues les parties chaudes. D Prévoir une période de refroidissement avant de travailler à l’équipement.
LES ACCUMULATIONS DE GAZ risquent de provoquer des blessures ou même la mort. D Fermer l’alimentation du gaz comprimé en cas de non utilisation. D Veiller toujours à bien aérer les espaces confinés ou se servir d’un respirateur d’adduction d’air homologué. Les CHAMPS ÉLECTROMAGNÉTIQUES (CEM) peuvent affecter les implants médicaux. D Les porteurs de stimulateurs cardiaques et autres implants médicaux doivent rester à distance.
Les PIÈCES MOBILES peuvent causer des blessures. LE RAYONNEMENT HAUTE FRÉQUENCE (H.F.) risque de provoquer des interférences. D Ne pas s’approcher des organes mobiles. D Ne pas s’approcher des points de coincement tels que des rouleaux de commande. LES FILS DE SOUDAGE peuvent provoquer des blessures. D Ne pas appuyer sur la gâchette avant d’en avoir reçu l’instruction. D Ne pas diriger le pistolet vers soi, d’autres personnes ou toute pièce mécanique en engageant le fil de soudage.
2-5. Principales normes de sécurité Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site Internet : www.global.ihs.com). Safe Practices for the Preparation of Containers and Piping for Welding and Cutting, American Welding Society Standard AWS F4.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site internet : www.global.ihs.com).
OM-237 881 Page 10
SECTION 3 − INTRODUCTION 3-1. Specifications Input Power Rated Output 3-Phase 350 A at 34 VDC, 60% Duty Cycle 1-Phase 300 A at 32 VDC, 60% Duty Cycle* Voltage Range in CV Mode Amperage Range in CC Mode Max. OpenCircuit Voltage 10−38 V 5−425 A 75 VDC RMS Amps Input at Rated Load Output, 60 Hz 3-Phase at NEMA Load Voltages and Class I Rating 208 V 230 V 400 V 460 V 575 V KVA KW 40.4 36.1 20.6 17.8 14.1 14.2 13.6 60.8 54.6 29.7 25.4 19.9 11.7 11.
3-4. Duty Cycle And Overheating Duty Cycle is percentage of 10 minutes that unit can weld at rated load without overheating. If unit overheats, output stops, a Help message is displayed and cooling fan runs. Wait fifteen minutes for unit to cool. Reduce amperage or voltage, or duty cycle before welding. . Single Phase Operation: The unit is supplied with a 8 AWG power cord. The rated output with 8 AWG is 300 amps, 32 volts at 40% duty cycle. To achieve 60% duty cycle change cord to 6 AWG.
SECTION 4 − INSTALLATION 4-1. Serial Number And Rating Label Location The serial number and rating information for this product is located on the rear panel. Use rating label to determine input power requirements and/or rated output. For future reference, write serial number in space provided on back cover of this manual. 4-2. Dimensions And Weight A Hole Layout Dimensions E F A 11-3/4 in. (298 mm) B 1-11/16 in. (42 mm) C 15-3/4 in. (400 mm) G 24 in. (610 mm) 17 in. (432 mm) D C D 19-3/32 in.
4-4. Weld Output Receptacles And Selecting Cable Sizes NOTICE − The Total Cable Length in Weld Circuit (see table below) is the combined length of both weld cables. For example, if the power source is 30 m (100 ft) from the workpiece, the total cable length in the weld circuit is 60 m (2 cables x 30 m). Use the 60 m (200 ft) column to determine cable size.
4-5. Remote 14 Receptacle Information Socket* Socket Information A 24 volts AC. Protected by supplementary protector CB2. B Contact closure to A completes 24 volts AC contactor control circuit. I 115 volts AC. Protected by supplementary protector CB1. J Contact closure to I completes 115 volts AC contactor control circuit. C Output to remote control; 0 to +10 volts DC, +10 volts DC in MIG mode. D Remote control circuit common. E 0 to +10 volts DC input command signal from remote control.
4-7. Optional Gas Valve Operation And Shielding Gas Connection Obtain gas cylinder and chain to running gear, wall, or other stationary support so cylinder cannot fall and break off valve. 4 1 Cylinder 2 Regulator/Flowmeter Install so face is vertical. 3 GAS IN Gas Hose Connection Fitting has 5/8-18 right-hand threads. Obtain and install gas hose. 2 4 Gas In Fitting 5 Gas Out Fitting The Gas In and Gas Out fittings have 5/8-18 right-hand threads.
4-8. Electrical Service Guide NOTICE − INCORRECT INPUT POWER can damage this welding power source. Phase to ground voltage shall not exceed +10% of rated input voltage. NOTICE − Actual input voltage should not be 10% less than minimum and/or 10% more than maximum input voltages listed in table. If actual input voltage is outside this range, output may not be be available. Failure to follow these electrical service guide recommendations could create an electric shock or fire hazard.
4-9. Connecting 1-Phase Input Power ! Installation must meet all National and Local Codes − have only qualified persons make this installation. ! Disconnect and lockout/tagout input power before connecting input conductors from unit. ! Always connect green or green/yellow conductor to supply grounding terminal first, and never to a line terminal. 1 8 =GND/PE Earth Ground 10 . The Auto-Line circuitry in this unit automatically adapts the power source to the primary voltage being applied.
4-10. Connecting 3-Phase Input Power ! Installation must meet all National and Local Codes − have only qualified persons make this installation. ! Disconnect and lockout/tagout input power before connecting input conductors from unit. ! Always connect green or green/ yellow conductor to supply grounding terminal first, and never to a line terminal. 3 = GND/PE Earth Ground 4 . The Auto-Line circuitry in this unit au- tomatically adapts the power source to the primary voltage being applied.
SECTION 5 − GENERAL OPERATION 5-1. Front Panel 6 4 9 2 3 5 7 8 10 11 12 13 14 1 15 19 18 16 17 804 772-A / 226 611-A . Weld process operation sections describe functionality of the identified items. 1 2 3 4 5 6 Remote 14 Receptacle Output ON Indicator Light Volts Indicator Left Display Arc Length Indicator Right Display OM-237 881 Page 20 . The meters display the actual weld output values after arc initiation and remains displayed for approximately three seconds after the arc is broken.
5-2.
5-3. Configuration Option Menu 4 3 SET 5 -UP 6 7 226 611-A 2 1 Mode Switch 2 3 Remote 14 Receptacle Left Display 4 Right Display 5 6 Adjustment Control Remote PC Interface 7 Setup Button OM-237 881 Page 22 1 Setup The Configuration Option Menu provides a means to customize some machine features for desired operation. To enter the Configuration Option Menu, hold the Setup Button down during power up while the unit is displaying 8888 on the Left and Right Displays.
5-3 Configuration Option Menu (Continued) V.SEN MIG V-Sense Feeder Weld Process This option enables MIG (V.SEN MIG) or Pulsed MIG (V.SEN PULS) when the Mode Switch is in the VSENSE FEEDER position. See Section 7-2 for MIG operation or Section 7-4 for Pulsed MIG operation. Pulsed MIG Manual/Auto Control PULS AUTO This option sets the PULSED MIG control as manual (PULS MAN) or Auto (PULS AUTO) operation.
5-3 Configuration Option Menu (Continued) Revision Information NO INFO This option identifies the unit’s weld library (INFO LIB) and firmware revision (INFO REV). Press the Setup Button while the unit is displaying INFO LIB to identify the unit’s weld library. Press the Setup Button while the unit is displaying INFO REV to identify the unit’s firmware revision. Pressing the Setup Button while the unit is displaying INFO NO will move to the next configuration option.
6-2. Scratch Start TIG Welding Mode - GTAW Process 2 3 7 2. 0 4 5 6 85 226 611-A 1 ! Weld terminals are energized at all times in Scratch Start TIG welding mode. 1 Mode Switch 2 Volts Indicator 3 Left Display 4 Right Display 5 Amps Indicator 6 Adjust Control Setup For typical system connections refer to Section 6-1. Rotate Mode Switch to SCRATCH START TIG position as shown. The open circuit voltage is shown in the Left Display with the Volts Indicator lit.
6-3. Lift-Arc TIG Welding Mode - GTAW Process 2 3 4 1 3. 5 6 5 85 226 611-A 1 8 “Touch” 1−2 Seconds 7 Do NOT Strike Like A Match! ! Weld terminals are energized at all times in Lift Arc TIG welding mode. 1 Mode Switch 2 Volts Indicator 3 Left Display 4 Right Display 5 Amps Indicator 6 Adjust Control 7 Workpiece 8 Tungsten Electrode OM-237 881 Page 26 Setup Operation For typical system connections refer to Section 6-1.
6-4. TIG Welding Mode - GTAW Process 2 3 4 5 85 226 611-A 1 ! Weld terminals are energized through the remote control in TIG welding mode. 1 2 3 4 5 Mode Switch Left Display Right Display Amps Indicator Adjust Control Setup For typical system connections refer to Section 6-1. Rotate Mode Switch to TIG position as shown. The preset amperage is shown in the Right Display with the Amps Indicator lit. Operation The Adjust Control is used to set desired preset amperage.
SECTION 7 − GMAW/GMAW-P/FCAW OPERATION 7-1. Typical Connection For Remote Control Feeder GMAW/GMAW-P/FCAW Process 9 1 2 3 4 8 7 5 6 804 938-A 5 Workpiece 6 Gun 7 Wire Feeder Negative (−) Weld Output Terminal 8 Gas Hose Ground Cable to Workpiece 9 Gas Cylinder ! Turn off power before making connections. 1 Remote 14-Receptacle 2 Positive (+) Weld Output Terminal 3 4 OM-237 881 Page 28 Use of shielding gas is dependant on Wire Type. .
7-2. MIG Welding Mode - GMAW/FCAW Process 2 3 4 5 2 5.0 6 7 8 9 226 611-A 1 ! Weld terminals are energized through the remote control in MIG welding mode. 1 Mode Switch 2 Volts Indicator 3 Left Display 4 Right Display 5 Adjust Control 6 Wire Type Indicator 7 Arc Control Indicator . The preset voltage can be adjusted re- motely at the wire feeder if the feeder has a voltage control. This voltage control will override the Adjust Control of preset voltage on the welding power source.
7-3. MIG - Wire and Gas Selection Table WIRE TYPES** GAS TYPES DEFAULT INDUCTANCE .035 (0.9) STL .045 (1.2) STL .052 (1.4) STL ARGN CO2 (ARGON / CARBON DIOXIDE) ARGN OXY (ARGON / OXYGEN) 30 .035 (0.9) STL .045 (1.2) STL CO2 (CARBON DIOXIDE) 10 Flux Core .035 (0.9) FCAW .045 (1.2) FCAW .052 (1.4) FCAW 1/16 (1.6) FCAW ARGN CO2 (ARGON / CARBON DIOXIDE) * CO2 (CARBON DIOXIDE) 30 * Metal Core .045 (1.2) MCOR .052 (1.4) MCOR 1/16 (1.6) MCOR ARGN CO2 (ARGON / CARBON DIOXIDE) 30 Stainless Steel .
7-4. Pulsed MIG Welding Mode - GMAW-P Process 2 3 4 5 6 25.0 7 8 9 10 1 ! Weld terminals are energized through the remote control in Pulsed MIG welding mode. 1 2 3 4 5 6 7 8 9 10 Mode Switch Volts Indicator Left Display Right Display Arc Length Indicator Adjust Control Wire Type Indicator Arc Control Indicator Setup Button Gas Type Indicator Setup For typical system connections refer to Section 7-1. Rotate Mode Switch to PULSED MIG position as shown.
7-5. Pulsed MIG - Wire and Gas Selection Table WIRE TYPES* GAS TYPES Steel .035 (0.9) STL .045 (1.2) STL ARGN CO2 (ARGON / CARBON DIOXIDE) ARGN OXY (ARGON / OXYGEN) Metal Core .045 (1.2) MCOR .052 (1.4) MCOR ARGN CO2 (ARGON / CARBON DIOXIDE) Stainless Steel .035 (0.9) SSTL .045 (1.2) SSTL TRI MIX (TRI-GAS MIXTURE) ARGN OXY (ARGON / OXYGEN) ARGN CO2 (ARGON / CARBON DIOXIDE) .035 (0.9) AL4X (4000 Series) .040 (1.0) AL4X (4000 Series) 3/64 (1.2) AL4X (4000 Series) 1/16 (1.
7-6. Remote Process Select This power source can be used with wire feeders that support Remote Process Select. This feature allows the operator to switch the active welding process between MIG and Pulsed MIG at the wire feeder. To determine if the welding system is Remote Process Select capable, connect the wire feeder to the power source and review the power source display variations shown below. .
7-7. Typical Connection For Voltage-Sensing Feeder GMAW/GMAW-P/FCAW Process ! Turn off power before making connections. 1 Positive (+) Weld Output Terminal 2 Negative (−) Weld Output Terminal 3 Ground Cable to Workpiece 4 Workpiece 5 Voltage Sensing Clamp 6 Gun 7 Gun Trigger Receptacle 8 Wire Feeder 9 Gas Hose 10 Gas Cylinder 10 1 9 3 Use of shielding gas is dependant on Wire Type. 2 . The connection diagram illus- trates DCEP (reverse polarity) suitable for all wires except self-shielded FCAW.
7-8. V-Sense Feeder Welding Mode - GMAW/FCAW Process 2 3 4 5 2 5.0 6 7 8 9 226 611-A 1 ! Weld terminals are energized at all times in V-Sense Feeder welding mode. Operation 1 Mode Switch While the Volts Indicator is lit under the Left Display, the Adjust Control is used to set desired preset voltage. 2 Volts Indicator .
7-9. V-Sense Feeder Welding Mode - GMAW-P Process 2 3 4 5 6 2 5.0 R200 7 8 9 10 226 611-A 1 ! Weld terminals are energized at all times in V-Sense Feeder welding mode. 1 Mode Switch 2 Volts Indicator 3 4 Left Display Right Display 5 Arc Length Indicator 6 7 Adjust Control Wire Type Indicator 8 Arc Control Indicator 9 Setup Button 10 Gas Type Indicator Setup For typical system setup connections refer to Section 7-7. Rotate Mode Switch to V-SENSE FEEDER position as shown.
SECTION 8 − SMAW/CAC-A OPERATION 8-1. Typical Connection For SMAW And CAC-A Process ! Turn off power before making connections. 1 Electrode Holder (Carbon Arc) 5 For CAC-A process connect carbon arc cutting torch to to positive weld output terminal. 4 2 3 3 4 2 Electrode Holder Positive (+) Weld Output Terminal Remote 14 Receptacle Connect desired remote control to remote 14 receptacle as required. 5 6 1 6 7 Compressed Air LIne Negative (−) Weld Output Terminal Workpiece 7 Ref.
8-2. CC Welding Mode - SMAW/CAC-A Process 2 3 4 5 85 6 7 1 ! 1 2 3 4 5 6 7 Weld terminals are energized through the remote control in CC welding mode. Mode Switch Left Display Right Display Amps Indicator Adjust Control Arc Control Indicator Setup Button Setup For typical system connections refer to Section 8-1. Rotate Mode Switch to CC position as shown. The preset amperage is shown in the Right Display with the Amps Indicator lit. .
8-3. Stick Welding Mode - SMAW/CAC-A Process 2 4 3 7 2. 0 6 5 85 7 8 1 ! Weld terminals are energized at all times in Stick welding mode. Right Display, the Adjust Control is used to set desired preset amperage. 1 2 3 4 5 6 7 8 Mode Switch Volts Indicator Left Display Right Display Amps Indicator Adjust Control Arc Control Indicator Setup Button Pressing the Setup Button allows adjustment of Arc Control, Hot Start Current and Hot Start Time.
8-4. Optional Low Open Circuit Voltage (OCV) Welding Modes Low OCV Operation The unit can be optionally configured for low open circuit voltage (OCV) operation in Stick and Scratch Start TIG modes. When the unit is configured for low OCV operation only a low sensing voltage (approximately 15 VDC) is present between the electrode and the workpiece prior to the electrode touching the workpiece.
SECTION 9 − MAINTENANCE & TROUBLESHOOTING 9-1. Routine Maintenance ! Disconnect power before maintaining. . Maintain more often during severe conditions. 3 Months Repair Or Replace Cracked Cables Replace Damaged Or Unreadable Labels Replace Cracked Torch Body Repair Or Replace Cracked Cables And Cords Clean And Tighten Weld Connections 6 Months Blow Out Inside 9-2. Blowing Out Inside Of Unit ! Do not remove case when blowing out inside of unit.
9-3. Help Displays . All directions are in reference to the front of the unit. All circuitry referred to is located inside the unit. 1 HELP HELP 2 HELP HELP HELP HELP HELP OM-237 881 Page 42 25 Help 1 Display Indicates a malfunction in the primary power circuit. If this display is shown, contact a Factory Authorized Service Agent. Help 2 Display Indicates a malfunction in the thermal protection circuitry. If this display is shown, contact a Factory Authorized Service Agent.
9-4. Troubleshooting Trouble No weld output; unit completely inoperative. Remedy Place line disconnect switch in On position (see Sections 4-9 and 4-10). Check and replace line fuse(s), if necessary, or reset circuit breaker (see Sections 4-9 and 4-10). Check for proper input power connections (see Sections 4-9 and 4-10). No weld output; meter display On. Input voltage outside acceptable range of variation (see Section 4-8). Check, repair, or replace remote control. Unit overheated.
SECTION 10 − ELECTRICAL DIAGRAM Figure 10-1.
254 090-A OM-237 881 Page 45
69 4 Figure 11-1. Parts Assembly OM-237 881 Page 46 1 71 70 3 5 68 67 72 73 66 2 11 74 10 75 77 76 9 65 64 8 15 78 12 13 14 58 64 7 16 63 21 18 19 57 17 54 61 60 59 6 55 62 20 51 56 24 22 52 23 79 25 50 26 53 MOD 1 49 48 27 29 39 46 MOD 2 38 28 30 31 41 42 43 44 40 33 37 32 48 45 20 47 35 34 36 SECTION −11 − PARTS LIST Ref.
Item No. Dia. Mkgs. Part No. Description Quantity Figure 11-1. Parts Assembly . . . 1 . . . . . . . . . . . . . . . 237 879 . . . . . . . . . . . . . . . . . . . . . 175 256 . . . . . . . . . . . . . . . . . . . . . 178 551 . . . 2 . . . . . . . . . . . . . . . 134 327 . . . 3 . . . . . . . . . . . . . . . 138 442 . . . 4 . . . . . . . . . . . . . . . 195 585 . . . 5 . . . . . . . . . . . . . . . 135 483 . . . 6 . . . . . . . . . . . . . . . 225 097 . . . 7 . . . . . . . . . . . . . . . 211 503 . . .
Item No. Dia. Mkgs. Part No. Description Quantity Figure 11-1. Parts Assembly (Continued) . . . 33 . . . . . . . . . . . . . . . . . . . . . . . . . . Nameplate, Rear (Order by Model and Serial Number) . . . . . . . . . . . . . . . . . 33 . . . . . . . . . . . . . . . . . . . . ♦ . . Nameplate, Rear Aux (Order by Model and Serial Number) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ♦217 297 . . Cover, Receptacle Weatherproof Duplex Rcpt . . . . . . . . . . . . . . . . . . . . . . . . 34 .
Item No. Dia. Mkgs. Part No. Description Quantity Figure 11-1. Parts Assembly (Continued) . . . 64 . . . . . . . . . . . . . . . 218 183 . . Rcpt Assy, Tw Lk Insul Fem(Tweco Type) (Fac−Op) (Includes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209 473 . . . . Rcpt, Twist Lock Tweco Style (Female) Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185 712 . . . . Insulator, Bulkhead Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes SOCKET/WRENCH SELECTION TABLE (U.S. STANDARD) Specifications Socket or Wrench Size SOCKET/WRENCH SELECTION TABLE (METRIC) Specifications Socket or Wrench Size Bolt Diameter Decimal Equivalent Bolt Nut Bolt Diameter U.S. Decimal Equivalent Bolt Nut 1/4 in .250 in 3/8 in 7/16 in 6 mm .2362 in 10 mm 10 mm 5/16 in .3125 in 1/2 in 9/16 in 8 mm .3150 in 14 mm 14 mm 3/8 in .375 in 9/16 in 5/8 in 10 mm .3937 in 17 mm 17 mm 7/16 in .4375 in 5/8 in 3/4 in 12 mm .
Warranty Effective January 1, 2011 (Equipment with a serial number preface of MB or newer) This limited warranty supersedes all previous manufacturers warranties and is exclusive with no other guarantees or warranties expressed or implied. 6. LIMITED WARRANTY − Subject to the terms and conditions below, warrants to its original retail purchaser that new equipment sold after the effective date of this limited warranty is free of defects in material and workmanship at the time it is shipped from factory.
Owner’s Record Please complete and retain with your personal records. Model Name Purchase Date Serial/Style Number (Date which equipment was delivered to original customer.) Distributor Address City State Contact the Delivering Carrier for: Zip File a claim for loss or damage during shipment. For assistance in filing or settling claims, contact your distributor and/or equipment manufacturer’s Transportation Department.
