R E D S C A R L E T X ® O P E R A T I O N G U I D E b u i l d v 3 . 2 w w w . r e d .
THIS PAGE INTENTIONALLY BLANK
TABLE OF CONTENTS TABLE OF CONTENTS ............... 1 DISCLAIMER ................................. 3 Copyright Notice........................ 3 Trademark Disclaimer ................ 3 COMPLIANCE ............................... 4 Industrial Canada Emission Compliance Statements ............ 4 Federal Communications Commission (FCC) Statement .................................. 4 Australia and New Zealand Statement .................................. 5 Japan Statements......................
Verify Current Camera Firmware .................................155 Upgrade Procedure ................155 APPENDIX B: MANAGING DIGITAL MEDIA..........................156 Media ......................................156 Formatting Media ...................156 Media Capacity Remaining Status .....................................158 Eject Media from Camera (Unmount) ...............................158 Using REDMOTE / Touchscreen LCD ..............158 Using Side Handle .............159 Using Side SSD.............
DISCLAIMER RED® has made every effort to provide clear and accurate information in this Operation Guide, which is provided solely for the user’s information. While thought to be accurate, the information in this document is provided strictly “as is” and RED will not be held responsible for issues arising from typographical errors or user’s interpretation of the language used herein that is different from that intended by RED.
COMPLIANCE INDUSTRIAL CANADA EMISSION COMPLIANCE STATEMENTS This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
AUSTRALIA AND NEW ZEALAND STATEMENT This device has been tested and found to comply with the limits for a Class B digital device, pursuant to EN 55022:2006 JAPAN STATEMENTS This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
The Waste Electrical and Electronic Equipment (WEEE) mark applies only to countries within the European Union (EU) and Norway. This symbol on the product and accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling, please take this product to designated collection points where it will be accepted free of charge.
BEFORE YOU START Congratulations on your purchase of a RED DSMC® Digital Still and Motion Camera. Please read the attached safety instructions, and only then unpack the camera body and any accessories. If there is any physical damage or missing components for either your camera body or any accessories, please file a support ticket at www.RED.com/support. RED SCARLET-X Digital Still and Motion Camera IMPORTANT SAFETY INSTRUCTIONS READ BEFORE USING YOUR CAMERA A.
shock and serious injury to the user. DO NOT use the camera in the rain or under other conditions with high moisture without appropriate protection, and immediately remove power source if camera or accessories are exposed to moisture. WARNING: To reduce the risk of fire or electric shock, do not expose the camera or accessories to rain or moisture. J. DO NOT expose your camera to excessive vibration or impact (shock). Be careful not to drop your camera. Internal mechanisms may be damaged by severe shock.
CAUTION: The power cord plug for the AC Power Adapter is used as the power disconnect. To disconnect all power from the AC Power Adapter, unplug the power cord plug from the wall outlet. During use, the power cord plug should remain easily accessible at all times. R. Lithium Ion batteries may be subject to special handling requirements pursuant to federal and local laws. Please refer to specific shipping instructions included with your battery regarding proper transport of your battery.
THEORY OF OPERATION The RED family of Digital Still and Motion Cameras (DSMC) provide high performance digital imaging over a wide range of frame rates and optical formats including Super 35mm / APS-H. The RED DSMC camera is supplied as standard with a PL mount, and may be configured with mounts and 19 mm rods to accommodate most cinematography lenses, matte boxes and follow focus systems. Adaptors for 15mm offset studio and 15mm lightweight rods are also available.
This recording technique permits RGB color processing choices to be deferred to post production or to be adjusted in the field to help a director visualize alternative color treatments, without affecting the recorded RAW data’s image quality or dynamic range. The camera’s monitoring path converts RAW sensor data to a white balanced 12-bit depth 2048 x 1080 pixel RGB 4:4:4 video signal.
• Exporting to EXR file format will give you a multi-view EXR with both exposures (like a stereo EXR). NOTE: If you ignore the X-track data, you will have a standard exposure with up to 13.5 stops of dynamic range just as if you had not enabled HDRx. For this reason, we encourage the A-track exposure to be "normal" as it provides the most options. If you are tempted to shoot "over-under", you are then fully committed to using HDRx and your postproduction options are reduced.
LINE LEVEL ANALOG INPUTS The recording level of a Line input is affected only by the signal provided by the field production sound mixer or other external line level source. The sound mixer operator should choose a mixer output level that aligns a reference tone signal to the 0dBu (-20dBFS) reference mark drawn on the camera’s Audio Level Meter, or if using 0VU as reference level, a mixer output level that aligns a reference tone signal to the 0VU (-16dBFS) reference mark.
Example of HDMI Monitor Output in MENUS mode. RED LCD / BOMB EVF® The optional RED LCD and BOMB EVF are specialized video monitors that provide the user with a variety of tools to assist framing, focus and exposure, including: - Surround View™, which is an additional look around area, visible outside of the recorded image. - Frame Guides, showing common film presentation and television aspects such as 2.40:1 and 16:9.
REDMOTE® REDMOTE is a camera control unit for RED’s family of DSMC cameras that attaches to the rear of the camera Brain or rearmost expansion module. REDMOTE may also be detached from the camera or rearmost module and provide wireless remote control of the camera over proprietary REDlink™ protocol. Whether attached or operating via wireless, REDMOTE supports all controls necessary to operate the camera, including Record Start / Stop, Shutter Speed, White Balance, ISO and programmable User Keys.
Typical Magazine Folder and clip structure For additional information about digital magazines, refer to APPENDIX B: MANAGING DIGITAL MEDIA.
Where: A = camera A, 001 = reel 001, C002 = clip 002, and 0502 = May 02, and the digits * * are two random characters generated by the camera to prevent any possibility of duplicate names being created. So a three Clip sequence of Clip Folders within a Magazine Folder on Camera A would look like this: A001_C001_0502**.RDC 955-0003_v3.2, Rev- A1 A001_C002_0502**.RDC COPYRIGHT © 2012 RED Digital Cinema A001_C003_0502**.
MULTI CAMERA SHOOTS The scheme provides flexibility to uniquely identify Clips from different cameras on a multi-camera shoot. For example three cameras, slated as camera A, camera B, and camera C respectively, can generate these easily recognizable clips on their respective digital media Magazines. A001_C001_0502**.RDC B001_C001_0502**.RDC C001_C001_0502**.RDC 3D (STEREO) CAMERA SHOOTS The scheme also allows unique identification of Clips from left and right eye cameras on a stereo shoot.
CAMERA OPERATIONAL CONTROLS This section describes the available operational controls on the RED DSMC camera Brain, Side SSD Module, Side Handle and REDMOTE accessories.
• • Record Status LED: Indicates record status: o LED Off = No Media present.
• SSD Slot: Slot for REDMAG 1.8” SSD digital media Magazine. • User Key 1: Initiates user defined camera function. Undefined by Default. • User Key 2: Initiates user defined camera function. Undefined by Default. • User Key 1 + User Key 2 : Press both keys to Eject (unmount) REDMAG 1.8” SSD Magazine. • Focus / Record Button: Touch for Auto Focus, fully depress to Start or Stop Record.
SIDE HANDLE TOP B A C E D F A Battery Release D LCD Menu Keys B Focus / Record Button E LCD Display C Adjustment Ring F LCD Backlight Button RED Side Handle Controls - Top • Battery Door Release Button: Releases Side Handle battery door to permit battery exchange. • Focus / Record Button: Touch for Auto Focus, fully depress to Start or Stop Record. • Adjustment Ring: Selects and adjusts camera parameter values. Similar to the scroll wheel on the navigation group.
FRONT A A Stills / Movie Slider Side Handle Controls - Front • Stills / Movie Slider: Selects between STILLS and MOVIE modes of operation. NOTE: This switch is not active at this time. Default camera operation is MOVIE 955-0003_v3.
REAR A B C E D F RED Side Handle Controls - Rear A MENU Button D User Keys A-D B Rocker Switch E System Keys 1- 3 C Navigation Group F Thumbwheel Lock • Menu Button: Press to access / camera setup menus. • Rocker Switch: Increases or decreases selected value based on parameter selected in USER KEYs. 24 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
• Navigation Group: Allows navigation through camera menus, selection of camera parameter for adjustment, and adjustment of selected camera parameter. Side Handle Navigation Group A • • B Scroll Wheel Direction Keys C Enter Button o Scroll Wheel: Selects and adjusts camera parameter value. o Direction Keys: Navigates camera menus and may select parameter for adjustment. o Enter Button: Confirms selected parameter value adjustment. User Keys: User Function Keys A-D.
INSTALLATION / REMOVAL WARNING: THE SIDE HANDLE IS NOT HOT SWAPPABLE - MEANING YOU CANNOT REMOVE OR INSTALL WHILE THE CAMERA IS POWERED ON. BEFORE INSTALLING OR REMOVING THE SIDE HANDLE, YOU MUST POWER DOWN THE CAMERA. FAILURE TO DO SO MAY RESULT IN DAMAGE TO THE SIDE HANDLE AND / OR CAMERA BRAIN THAT IS NOT COVERED BY WARRANTY. To install the side handle: 1. Power down the camera if necessary. 2. Remove the brain side plate (if installed) by removing the single screw located at the bottom. 3.
To remove the side handle: 1. Power down the camera if necessary. 2. Rotate the thumbscrew downwards until detached from camera body. Disengage lip from top of camera brain. Rotate side handle upwards to remove. Rotate thumbscrew downwards until loose. 3. Rotate upwards and pull down to disengage lip at top of side handle from camera brain. 4. Remove side handle from camera. 955-0003_v3.
DSMC MODULES REAR SSD MODULE The Rear SSD Module secures onto the back of the DSMC brain to serve as a rear location for recording onto 1.8" REDMAG SSD media. QUAD BATTERY MODULE • The QUAD MATTERY MODULE holds up to 4 REDVOLTs or 2 REDVOLT-XLs • Batteries may be hot swapped Battery Eject Button Quad Battery Module – Shown with REDVOLT batteries Installed 28 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
DUAL BATTERY MODULE • The DUAL BATTERY MODULE holds up to 2 REDVOLTs • Batteries may be hot swapped Dual Battery Module – Shown with REDVOLT batteries Installed MODULE INSTALLATION / REMOVAL To install a DSCM Module to the camera, an Adaptor Plate must be purchased separately. The following procedure details installation of the Adaptor Plate and DSMC Module. Install the Adapter Plate 1. Power down the camera. 2. Remove the REDMOTE. 3.
30 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
4. Using a T-20 Torx, lightly tighten the four screws. Do not over tighten. 5. Tighten the screws again in a cross pattern until tight. 4 2 1 3 ATTACHING THE DSMC MODULE WARNING: DSMC Modules are NOT hot swappable - meaning you cannot remove or install while the camera is powered on. Before installing or removing a Module, you MUST power down the camera. Failure to do so may result in damage to the Module and / or camera brain that is not covered by warranty. Quad Battery Module shown. 1.
Rotate Module Down Until Flush with Adaptor Insert Lip At Top of Adaptor Plate 2. Rotate module down flush with the rear of the adaptor plate. 32 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
3. While applying steady pressure to hold the module against the adaptor plate, use a T-20 Torx screwdriver to rotate the lock on the adapter plate clockwise to secure the module. Press Battery Module Flush with Adaptor Rotate Lock Clockwise Until Red Dot Lines Up with Lock Icon Installation is now complete. To remove the DSMC Module and Adaptor Plate: 1. Power down the camera. 2. Use a T-20 Torx screwdriver to rotate the lock on the adapter plate to the Unlock position. 3.
C D L A K E H I M B F N G J REDMOTE Controls A Still/Motion Slider F User Keys A-D K Soft Menu Keys 4-8 B Release Button (L) G MENU Button L Power/Lock Slider C Record LED H Soft Menu Keys 1-3 M Release Button (L) D Power LED I Navigation Group N USB Connector E Rocker Switch J Focus / Record Button • Stills / Motion Slider: Allows selection of STILLS or MOVIE operational modes. • Rocker Switch: Provides continuous adjustment of parameter specified in USER KEYS menu.
• Navigation Group: Allows navigation through camera menus, selection of camera parameter and adjustment of selected camera parameter. REDMOTE Navigation Group A Scroll Wheel B Direction Keys C Enter Button - Scroll Wheel: Selects and adjusts selected camera parameter value. - Direction Keys: Navigates camera menus and may select parameter for adjustment. - Enter Button: Confirms selected parameter value adjustment.
• Contrast Ratio: 1000:1 typical • Available diopter range: +2.0 to -5.0.l Talley Light Focus Ring Brightness Controls RED BOMB EVF (OLED) brings advanced OLED technology into the field, providing truer blacks and more color accurate images • Resolution: 1280 (wide) x 1024 (high) full-color • Contrast Ratio: >10,00:1 typical • Available diopter range: +2.0 to -5.0.l l Focus Ring Talley Light Brightness Controls NOTE: The specific function of EVF user keys (B/C) may be programmed by the user.
TOUCHSCREEN LCD Red offers a five inch touch screen LCD with 800 X 400 resolution and 4:4:4 progressive scan. The touchscreen LCD allows navigation of camera menus and selection and adjustment of camera parameters by directly touching icons on the screen. Gestures supported include: • Tap: Tap on an icon to bring up a quick adjustment display. • Hold: Touch and hold on an icon to bring up an advanced interface display. • Slide: Touch and slide on an icon to increment a value.
BASIC OPERATION This section describes basic operation, starting from power up, Viewfinder layout and Menu navigation. WARNING: THE SIDE HANDLE, SIDE SSD MODULE, REAR MODULES AND LENS MOUNT ARE NOT HOT SWAPPABLE – MEANING YOU CANNOT REMOVE OR INSTALL THEM WHILE THE CAMERA IS POWERED ON. BEFORE INSTALLING OR REMOVING ANY OF THESE ACCESSORIES, YOU MUST POWER DOWN THE CAMERA. FAILURE TO DO SO MAY RESULT IN DAMAGE TO THE ACCESSORY AND / OR CAMERA BRAIN THAT WILL NOT BE COVERED UNDER WARRANTY.
QUAD BATTERY MODULE The optional QUAD BATTERY MODULE accepts up to four REDVOLT or up to two REDVOLT XL batteries, which can power the camera and typical accessories. Figure 16: Quad Battery Module REDVOLT AND REDVOLT XL REDVOLT and REDVOLT XL Note: When multiple batteries are installed in the Quad Battery Module, the power management circuit will select the lowest charged battery to supply power to the camera.
BACKPACK QUICKPLATE The optional BACKPACK QUICKPLATE attaches directly to the back of the DSMC BACKPACK to provide a compact REDBRICK configuration for EPIC or SCARLET-X. Note: DSMC BACKPACK is required for use of the BACKPACK QUICKPLATE BACKPACK QUICKPLATE REDBRICK 40 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
AC POWER ADAPTOR - (DSMC) AC POWER ADAPTOR - (DSMC) When powering from the Module it is called in the lower UI as Rear Module (RM Bx) Bay number on lower UI, and identified as Rear 1-4 in the POWER status menu. In use, an LED on the Quad Battery Module will flash to show the battery currently powering the camera.
Battery location and status are displayed in the lower UI. In this case RM B1 (Rear Module, Bay 1). Battery location and status are also displayed on REDMOTE. In this case RM B3 (Rear Module, Bay 3). The POWER menu also shows all installed batteries and their state of charge. EXTERNAL DC POWER RED DSMC Cameras accept input voltages between 11.5V - 17V D.C and can draw a maximum current of 12 Amps.
POWER UP Locate the camera’s Power / Record button on the right face of the Brain. NOTE: This button also serves as a Record Start / Stop button once the camera is powered up. A Power Status LED B Power / Record Button C Media Status LED Power / Record Button / Status LEDs When an appropriate power source is connected to the Brain, the Power Status LED will illuminate Red. If it is illuminated, depress and then release the Power / Record button.
NOTE: Once powered up, if the Power Status LED illuminates Red, it indicates low remaining battery capacity and a battery exchange or switch over to external DC power is recommended. POWER DOWN The camera can be powered down in two ways: 1. Using REDMOTE or Side Handle Menu controls, or via Touch Screen LCD icons. Refer to SECONDARY MENUS > POWER. 2. Depress and continue to hold the Power / Record button in its fully depressed position until the INITIATING CAMERA SHUTDOWN shows on the display.
GRAPHICAL USER INTERFACE AND NAVIGATION RED LCD/TOUCHSCREEN LCD, BOMB EVF, EXTERNAL MONITORS The following is a general description of the structure of the camera’s Graphical User Interface (GUI) which overlays the video monitor signal on the Viewfinder output(s) of the camera.
• Frame Guide: Record or Projection area • • Next Clip Filename: Filename of the clip that will be shot next Genlock: Indicates presence of valid Genlock signal / sensor sync to genlock • Shutter Sync: Indicates shutter sync status • Project Frame Rate: Current project TIME BASE • RM: Indicates communication to REDMOTE • Noise Level Bar: Relative number of RAW pixels in noise • LAN: Indicates communication via Ethernet connection • Histogram: RGB Histogram.
The GUI is broken down into the following three main sections: the Upper Status Row, the Live Action Area, and the Lower Status Row. On VIEWFINDER output(s), all three sections are visible, on PREVIEW outputs only the Live Action Area and associated graphic overlays are visible. On PROGRAM outputs, none of the graphic overlays are visible, i.e. a PROGRAM output is defined to be a CLEAN FEED output.
LIVE ACTION AREA Contains the recorded image area plus Surround View™ look around area, plus overlays for Frame Guide, Safe Action / Safe Title and the current Clip Name and Timecode values. Each overlay may be color coded in one of 5 colors to maximize the contrast between the guide(s) and scene being captured.
• GEN Green - A genlock signal compatible with the current project and monitor rates has been locked to. SYNC • SYNC Gray - The sensor sync mode is not Genlock. • SYNC Red - The sensor sync mode is Genlock, but it is not locked to any genlock signal. • SYNC Green - A genlock signal compatible with the current project and monitor rates has been locked to and the sensor timing is also locked to it. POWER STATUS If powering camera through DC power, the current voltage will be displayed.
RAW CLIP METER The RAW Clip meter looks a traffic light style meter and indicates if either of the Red, Blue or Green channels of the RAW sensor data are clipping. This meter is unaffected by White Balance, ISO, VIEW or LOOK settings and therefore represents a true measurement of the exposure levels of the sensor at all times. RAW NOISE LEVEL BAR The RAW noise level bar displays the amount of pixels in the image that are in noise.
SIDE HANDLE As you navigate and adjust settings on the camera (main menu settings only), they will be reflected on the Side Handle LCD display.
• Gen: Indicates presence of valid Genlock signal • Sync: Timecode Jam Sync status • RIG: Indicates 3D rig metadata is present • LAN: Indicates communication via Ethernet connection Clip Filename: Filename of the clip that will be shot • Media Status: Media location and remaining media capacity in % • Project Frame Rate: Current project TIME BASE • • Clip Meter: RGB sensor RAW clipping status Power: Indicates D.
USING TOUCHSCREEN LCD If operating a Touchscreen LCD, camera menu navigation may be made through finger gestures. • To adjust a parameter value, simply touch it, and then swipe the finger left / right to adjust its value. • To access an advanced parameter settings display, press and hold down on the parameter icon. • Touch anywhere outside the overlay windows to enter the value changes and to hide the sub-menus. • To enter the Secondary Menus, touch the MENU icon.
TOUCHSCREEN SHORTCUTS The bottom portion of the touchscreen contains shortcuts to the most-used camera screens. 54 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
POWER DOWN NOTE: Camera will automatically power down if supply voltage drops to 11.5 Volts. POWER MENU 1. Select the MENU icon Menus. in the right corner of the Upper Status Bar to reveal the Secondary 2. Select POWER. 3. Select SHUTDOWN. 4. The camera will immediately power down. USING POWER STATUS DISPLAY 1. Select the POWER status located between the audio channels and media remaining indicator, to reveal the same menu illustrated above. 2. Select SHUTDOWN. 3. The camera will immediately power down.
LOCK / UNLOCK TOUCHSCREEN OPRERATION LOCK To lock out the touchscreen operation, touch and hold the MENU icon until the LOCK icon displays; indicating the touchscreen has been locked out. When locked, the main menu will be displayed. UNLOCK To unlock out the touchscreen and allow normal operation, touch and hold the LOCK icon MENU icon displays; indicating the touchscreen has been unlocked. 56 COPYRIGHT © 2012 RED Digital Cinema until the 955-0003_v3.
FIRST TIME USE – SETTING UP YOUR RED EPIC ATTACH POWER SOURCE If a REDVOLT battery is installed in the Side Handle and DC power is connect through the DC IN connector, the DC IN power supply has priority and will power the camera instead of the battery. BATTERY Connect a RED battery to the camera in one of the following ways: SIDE HANDLE Attach a Side Handle and insert a REDVOLT battery. INSTALL A C B 1. Press the battery door release button (A). 2. Open battery door (B). 3.
REMOVE 1. Press the battery door release button (A). 2. Open battery door (B). 3. Press upwards on retainer (C) to release battery. 4. Remove battery from side handle. QUAD BATTERY MODULE Attach a Quad Battery Module and insert one or more REDVOLT batteries. INSTALL Insert battery into desired location and press until a click is heard and battery is seated. REMOVE B B A 1. Press the battery eject button (A) for desired battery. 2. When battery pops out, remove battery from battery module (B).
RED BRICK Attach to the camera using a V-Plate and 2B-to-1B Power Adapter Cable P/N 790-0138 to the DC IN connector. DC POWER Connect a DC power source to the camera in one of the following ways: • Plug the RED AC Power Adapter into AC power, and the LEMO connector to the DC IN connector. • Plug the RED CHARGER into AC power, and the LEMO connector to the DC IN connector via 2B-to1B Power Adapter Cable P/N 790-0138.
NOTE: When fully inserted, the SSD media protrudes slightly from the SSD slot as indicated above. When SSD media is inserted into the camera, the camera will recognize if the media is unformatted: - On LCD, EVF and external monitors, in the media section of the GUI, NONE will be displayed twice (as opposed to when no media is inserted, the GUI displays NONE with three dashes below “---“).
PERFORM A BLACK SHADING CALIBRATION Refer to SECONDARY MENUS > SETTINGS > MAINTENANCE > CALIBRATION for complete details for performing a Black Shading Calibration. ADJUST PROJECT SETTINGS TIME BASE To adjust the project TIME BASE, press the MENU button on the Side Handle or REDMOTE. Then use the Scroll Wheel or Direction Keys to navigate to SETTINGS > PROJECT > TIME BASE and press ENTER. Adjust to the desired value using the Scroll Wheel and press ENTER once more to confirm.
RECORD RESOLUTION To adjust Record Resolution, navigate the Cursor to the RESOLUTION icon in the Upper Status Row and press the Navigation Group ENTER key. Adjust to the desired value using the Scroll Wheel and press ENTER a second time to confirm. If using a Touch Screen, press the RESOLUTION ICON, adjust RESOLUTION by sliding your finger left / right, or tap on the desired resolution, and then press anywhere else on the touch screen to confirm.
CAMERA ID (SLATE) If operating on a multi-camera production, enter a different Camera ID for each camera; otherwise skip this step; the camera is ready to shoot. The Camera ID is set when the media is formatted. Refer to ADVANCED MENU > MEDIA for details. RECORDING Ensure a formatted REDMAG 1.8” SSD is inserted in the camera’s Side SSD Module, then fully depress any one of the RECORD buttons located on the Brain, Side SSD Module, Side Handle or REDMOTE. Fully depress again to stop recording.
- If using a BOMB-EVF, the LED on the front will illuminate Red if Tally is enabled - SMPTE-RP188 timecode VITC-2 HANC metadata record flag will be enabled on HD-SDI outputs. - If enabled in the USER KEYS menu, the GPO trigger output in the CNTL connector will pulse. PLAYBACK Playback is available on the RED DSMC Camera by going to SECONDARY MENUS > SETTINGS > PLAYBACK or by touching the Playback arrow icon in the upper Left corner of the GUI. The Playback function will display.
MENU CONTROLS Displayed in the Upper Display Group of the VIEWFINDER output(s), are FRAMERATE (FPS), EXPOSURE (ISO), _._ (F/Stop), WHITE BALANCE, RESOLUTION, and QUALITY (REDCODE). These parameters are adjustable directly through this screen. When using the touchscreen, directly to the right of these parameters is the MENU icon which when pressed will take you to the secondary camera set up menus.
• To close an alpha numeric keypad when entering information directly, tap anywhere on the screen outside the keypad. ADVANCED SETTING MENUS At this time, only FRAMERATE, F-STOP, SHUTTER SPEED and WHITE BALANCE on the MAIN MENU have advanced settings SIDE HANDLE / REDMOTE 1. Navigate to the desired setting using the NAVIGATION GROUP direction keys and then press the UP directional key. 2. Use the direction keys to navigate to the desired parameter adjustment field and press ENTER to confirm. 3.
MAIN MENU Available options under the MAIN MENU are FRAMERATE (FPS), ISO (SENSITIVITY), F STOP, 1/SEC (EXPOSURE), WHITE BALANCE, RESOLUTION, and QUALITY (REDCODE). FPS If using a Touch Screen, select SECONDARY MENUS > SETTINGS > PROJECT > TIME BASE. Adjust by sliding your finger up / down or tapping on the desired value, and then press anywhere else on the touch screen to confirm. The following TIME BASES are currently available: • 23.98 fps • 25.00 fps • 47.96 fps • 50.00 fps • 24.00 fps • 29.
BASIC SETTINGS Provides quick selection of the most common VARISPEED frame rates. ADVANCED SETTINGS When selected a numerical keypad will appear allowing the desired VARISPEED Framerate to be entered in 1 fps increments. Maximum frame rate is a function of RECORD RESOLUTION and REDCODE settings. Granularity is 0.001 FPS. On Touchscreen systems, a Keypad is available for direct numeric entry of the VARISPEED FPS value.
ISO (SENSITIVITY) Adjusts the camera’s ISO rating. The sensitivity value is adjustable in 1/3rd stop increments. When the ISO rating is adjusted, the camera logs the change as metadata and the monitor path reacts accordingly. Higher ISO values lead to brighter images in the monitor path, and vice versa.
BASIC SETTINGS Allows adjustment of the aperture (F stop) of the attached lens. The range will vary depending on the attached lens. ADVANCED SETTINGS When selected, the advanced settings menu allows fine control over the f-stop value under APERTURE and focal distance under FOCUS. APERTURE (F STOP) Provides the ability to enter the F stop value directly. Range depends on attached lens. Default depends on attached lens. 70 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
FOCUS Provides the ability to enter the focal distance directly. Range depends on attached lens. Default depends on attached lens. EXPOSURE BASIC SETTINGS Adjusts the exposure of each frame captured by the MYSTERIUM X sensor. Shutter speed presets are provided for all common speeds (and shutter angles) for 24 / 25 fps and 50 / 60 fps project frame rates.
ADVANCED SETTINGS When selected, the advanced settings menu allows fine control over the Exposure value, and permits entry in any of the three following common units – EXPOSURE (Shutter Speed), INTEGRATION TIME or ABSOLUTE ANGLE (Shutter Angle). EXPOSURE (SPEED) Provides the ability to enter the Exposure value as a Shutter Speed (1/xx sec). Range is 2 – 1/8000th Sec - Slowest available speed is 1/frame rate, so for 24 fps it is 1/24th Sec. Default is 1/48th Sec.
INTEGRATION TIME Provides the ability to enter the Exposure value as a Shutter Integration Time (xx milliseconds). Range is 0.125 to 41.708 mS (milliseconds) Default is 20.833 MS ABSOLUTE ANGLE Provides the ability to enter the Exposure value as a Shutter Angle (xx Degrees). Range is 1.000 to 360.000 Degrees Default is 180.
To Convert Shutter Speed to Angle Equivalent: Equivalent Degrees = (Shutter Speed x Frame Rate x 360) E.g. = (1/48 x 24 x 360) = (8640/48) = 180 SHUTTER DEGREES SHUTTER DEGREES 1/32 270 1/120 72 1/48 180 1/192 45 1/50 172.8 1/348 22.5 1/60 144 1/696 11 1/96 90 1/1000 8.6 Equivalent Shutter = 1 / (Frame Rate x 360 / Angle) E.g. = 1/ (24 x 360/180) = 1/ (8640/180) = 1/48 DEGREES SHUTTER DEGREES SHUTTER 270 1/32 72 1/120 180 1/48 45 1/192 172.8 1/50 22.
ADVANCED SETTINGS When selected, allows additional adjustment of the White Balance. Available options are PRESET, COLOR TEMP, TINT, and CALCULATE WHITE BALANCE. Press APPLY PRESET for settings to take effect.
TINT Color Temperature calculations assume a pure light source that may not be true in the specific scene the camera is imaging. To compensate for any residual colorcast, the TINT parameter can adjust the RGB color balance with a compensating Magenta - Green color component. Default is 0.000. When selected, a secondary keypad will appear allowing you to enter the desired Tint value directly. NOTE: Selecting Calc White Balance calculates a new Tint value.
RESOLUTION Allows adjustment of resolution. Default is 5K 2:1 FORMAT WIDTH (PX) HEIGHT (PX) 1K WS 1280 480 1K HD 1280 720 2K WS 2048 854 2K HD 1920 1080 2K 2048 1080 3K HD 2880 1620 3K 3072 1620 4K HD 3840 2160 4K 4096 2160 5K ANA 3600 2700 5K WS 5120 2160 5K 2:1 5120 2560 5K HD 4800 2700 5K 5120 2700 REDCODE Allows adjustment of REDCODE settings. Range is 3:1 to 18:1 Default is 8:1 Use the scroll ribbon to select a target REDCODE compression ratio.
If the camera is able to achieve the desired target compression ratio, it will be displayed in white. If the camera is unable to achieve the target compression ratio, it will be displayed in yellow. The current compression ratio will automatically be re-calculated when changes are made to Resolution, FPS, HDRX Mode, Media, or Target REDCODE.
HDR ON / OFF By default, HDRx is OFF (HDR button is illuminated Blue). In the Lower Status Group of the Viewfinder screen, the HDR text is Gray, indicating HDRx is inactive. To turn HDRx on, navigate to the HDRx button using the Navigation Group and press ENTER, or from the touchscreen directly touch the HDRx button. In the Lower Status Group of the Viewfinder screen, the HDR text will turn White, indicating HDRx is active.
MODE MANUAL FOCUS To adjust the MODE parameter, select the Menu box and use the UP / DOWN arrows to adjust. Available options are MANUAL and CONFIRM. Default is MANUAL. MANUAL When selected all focus operations are manual. CONFIRM Enables the Center or Spot focus square for use with manual focus. This mode provides additional focus assistance to the photographer using RED, YELLOW, and GREEN color changes to the focus spot window.
Performance of Auto Focus may be reduced under the following conditions: • The subject is dark or distant. • There is inadequate contrast between the subject and background. • The scene has reflective highlights. • The subject is backlit. • There is inadequate surface contrast/detail inside the window. NOTE: Edge Mode can be used for additional assistance in these conditions. Refer to SETTINGS MENU > DISPLAY > TOOLS > EDGE. MANUAL When selected all focus operations are manual.
CONTINUOUS Once engaged with half-press, will attempt to keep objects in AF window in focus. Works best with good lighting and contrast. Works with both Center and Spot Zones. TOUCH TRACK Dynamically updating positionable AF using touchscreen. Works with Spot Zone only. Keep AF Spot on subject while moving across frame, will continuously focus on spot. RACK For quickly selecting two focus points and executing rack focus between them. Focus points are selected using the Touchscreen.
DSMC CANON MOUNT ELECTRONICALLY SUPPORTED LENSES Canon EF 100-400mm f/4.5-5.6L IS Canon EF 100mm f/2.0 USM Canon EF 100mm f/2.8L Macro IS USM Canon EF 135mm f/2.0L Canon EF 135mm f/2.8 Soft Focus Canon EF 14mm f/2.8L II USM Canon EF 15mm f/2.8 Fisheye Canon EF 16-35mm f/2.8L II Canon EF 17-40mm f/4L Canon EF 180mm f/3.5L Macro Canon EF 200mm f/2.0L IS Canon EF 200mm f/2.8L II Canon EF 20mm f/2.8 USM Canon EF 24mm f/1.4L II Canon EF 24-105mm f/4L IS Canon EF 24-70mm f/2.8L Canon EF 24mm f/2.
ZONES Available options are CENTER and SPOT. Default is CENTER. This control allows selection of the boxes used to indicate objects in/out of focus. CENTER Provides a large, square target for focus. When objects located in the circle are in focus, the square will be Yellow or Green. When objects located in the square are out of focus, the square will be Red. 84 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
SPOT Provides a small, square target for precise focus (similar to Center focus, only smaller). When objects located in the square are in focus, the square will be Yellow or Green. When objects located in the square are out of focus, the square will be Red. SPOT FOCUS INDICATOR Moving The spot focus square can be moved around the screen. Touchscreen Tap on the spot focus square directly on the touchscreen and drag to the location you wish to relocate the spot focus circle. 955-0003_v3.
Side Handle / REDMOTE 1. Navigate to the focus menu. 2. Press the down arrow on the Navigation Group. 3. The spot focus square line weight will increase and the Red cursor under FOCUS will dim slightly. 4. Press the ENTER button. 5. Use the directional arrows to move the Spot Focus square to the desired location. 6. To exit: - Press the ENTER button, the spot focus square line weight will increase, then press the UP arrow to go back to the FOCUS menu. - Press the MENU button.
LENS INFORMATION DISPLAY RED DSMC TI PL MOUNT + LENS When a RED DSMC Ti PL Mount is installed and a Lens equipped with Cooke’s S4/i system (or equivalent is attached, the Focal Length and Focal Distance is displayed on the LCD, EVF and external monitors. The focal length and focal distance values and range will vary depending on the attached lens. When the focal length or focal distance of the lens is manipulated, the current values are displayed.
EXPOSURE MENU Not implemented at this time. PRESETS MENU CAMERA PRESETS Camera Presets are used to store and recall camera setup information such as LOOKs, key mappings, I/O configuration, etc. Your RED DSMC camera has a number of factory-installed settings. APPLYING A PRESET • Select Presets from the secondary menus • Select the desired preset from the selection ribbon • Press APPLY button • Use the selection ribbon to selcet Custom presets may be created to store groups of camera settings.
• Select Create and enter a name for the new preset using the QWERTY keyboard • Press OK on keyboard to save the preset name • Copy the desired settings from the left box of the interface to the right box using the select one (-->) or select all button • Select and press Create button (upper right corner of the screen) The preset has been created and is now stored on the camera. 955-0003_v3.
SHARING PRESETS Presets may be shared between RED DSMC cameras using SSD media. Camera to camera Camera to multiple cameras Select Presets from the secondary menu: On SSD On Camera 90 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
COPY PRESETS FROM CAMERA TO SSD • Use scroll ribbon to select desired preset in camera box • Use --> button to move the preset to the SSD box COPY PRESETS FROM SSD TO CAMERA • Use scroll ribbon to select desired preset in SSD box • Use --> button to move the preset to the Camera box • The following window will appear • Select Yes to copy the preset to the camera and apply the setting • Select No to copy the preset to the camera without applying the settings MANAGING PRESET FILES • The APPLY,
LOOKS PRESETS Look Presets allows you to save the specific color, image, white balance, and detail settings to be used for other projects. Meta is the default settings shot on the camera and cannot be deleted. As looks are created, they will be displayed alphabetically. For detailed information on LOOKs, see the REDCINE-X Operation Guide, available on RED.com 92 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
If MEDIA MENU The Media Menu is used to format media (SSD) prior to use on the camera as well as to Eject (unmount) the media prior to removal from the camera. Available options when selected are SELECT MEDIA, FORMAT MEDIA, EJECT MEDIA, and UTILITIES. IMPORTANT: Media MUST be ejected from the camera before removal to prevent corruption and/or loss of data on media. SELECT MEDIA Allows you to select the Media location to be used by the camera. Default is the Side SSD (S-SSD) Module.
NOTE: If clips are present on the media, you will be informed of how many clips will be erased when you format the media. REEL NO. When selected a keypad will appear allowing you to enter a value between 1 and 999. CAMERA ID (SLATE) Identifies the camera with a letter A through Z. Default is A. CAMERA POS (POSITION) Identifies the camera position as Right, Left or Center. Default is Center. FORMAT When selected, formats the media and adds the selected properties.
UTILITIES Options are SECURE FORMAT. SECURE FORMAT Secure Format is a low-level format the rebuilds the SSD file system. It should only be used if the performance of the SSD is in question. NOTE: If clips are present on the media, you will be informed of how many clips will be erased when you secure format the media. 955-0003_v3.
SETTINGS MENU This section describes the various secondary controls available to configure the camera. Menu options are DISPLAY, LOOK, SENSOR, PROJECT, MODES, AUDIO/VIDEO, SETUP, MAINTENANCE, and PLAYBACK. DISPLAY Available options are TOOLS, ZEBRA, OVERLAY, MODES, FRAME GUIDE, AREA GUIDES, and MONITOR. TOOLS The Tools menu permits the operator to adjust the GUI elements displayed on the Viewfinder output(s) Available options are OFF, EXPOSURE, FOCUS, VIDEO, EDGE, MAGNIFY, and RAW.
EXPOSURE This will show areas of under exposure (Purple) or over exposure (Red) on top of a monochrome image. The color is based on RAW data so over/under exposure refers to data actually close to clipping in the sensor. When selected, the icon “E√” will be displayed in the Lower Status Group. The EXPOSURE meter’s color bands provide the following information: PURPLE Minimum Exposure RED Maximum Exposure Between minimum and maximum exposure values, the image is displayed as a monochrome image.
FOCUS This will emphasize edges in the image without changing brightness/image content so it is easier to judge if the image is in focus. By adjusting your lens zoom and focus you can see which objects are coming into and falling out of focus. When selected, the icon “F √” will be displayed in the Lower Status Group.
ORANGE Super White (IRE 105-107) RED Super White (IRE 108-109) At all other values, the monochrome image displayed represents the luminance value of the ISO adjusted image. EDGE EDGE displays a color overlay that outlines the edges of objects in an outline mode. By adjusting your lens zoom and focus you can pinpoint focus. When selected, the icon “F√” will be displayed in the Lower Status Group. WARNING: This will potentially interfere with recordings done via HDMI/HD-SDI in "Clean" Mode! 955-0003_v3.
MAGNIFY Magnify displays the central region of the sensor in 1:1 pixel resolution. When enabled, the 1:1 text in the Lower Status Group will change to Green. If in Magnify mode, when the Record button is pressed, the system will automatically exit this mode. When using a touchscreen you can also perform this function by pinching your fingers together and apart. NOTE: HDR mode cannot be modified when in Magnify 1:1 mode. NOTE: When in magnify mode, you will not be able to adjust frame rate or resolution.
RAW RAW displays the image without any ISO correction. When selected, OFF will be highlighted in the Lower Status Group. ZEBRA Zebras enable and adjust the upper and lower values for two independent Zebra indicators. One zebra may be used for highlight exposure, and the other for mid tone or shadows. Zebras will be visible when in 1:1 zoom. By default, Zebra 1 and 2 are disabled. 955-0003_v3.
ZEBRA 1 To enable, select ZEBRA 1 check box. Areas of the image exposed within these ranges will be indicated by crosshatched overlays at - 45 degrees relative to vertical. Zebra 1 is shown in the image below. High IRE Change the desired setting between 93 and 109 (default is 108). Low IRE Change the desired setting between 75 and 107 (default is 99). ZEBRA 2 To enable, select ZEBRA 2 check box.
Low IRE Change the desired setting between 0 and 84 (default is 44). OVERLAY Allows you to enable and color code graphic overlays visible the on the Viewfinder and Preview outputs. Use check boxes and pull down menus to control appearance of the overlays Grid The Grid display is shown below. The grid may be used as a “rule of thirds” indicator. 955-0003_v3.
Look Around Highlights the look around area. Overlay Elements Motion Data (Pitch & Roll) Lens Info 01:17:06:16 File Name 104 Scene Name COPYRIGHT © 2012 RED Digital Cinema Time Code 955-0003_v3.
MODES Available GUI display mode adjustments are Exposure, Shutter Mode, Aperture, and Focal Distance. EXPOSURE Selects GUI display of Shutter Exposure on Main screen as Time (1/xx sec) or Angle (Degrees). Default is Time. Angle is shown below. SHUTTER Enables one of two shutter timing (duration) modes: Absolute or Relative. Default selection is Absolute. Absolute Shutter Speed is defined exclusively by the Shutter Speed setting.
APERTURE Selects GUI display of f/stop as 1/4 f Stop or 1/3 f Stop. Default is 1/3. FOCAL DISTANCE Allows you to set the Lens Info to display in Metric or Imperial measurements. Default is Imperial. GUIDES This sub-menu provides a selection of frame guides and safe action and safe title guides. User definable safe action and safe title guides may be saved as a USER PREFERENCE, thereby permitting the camera guides to be fully customized for any application.
SIZE Available options are Off, Full, 4:3, 16:9, 1.85:1, 1.9:1, 2.4:1, or User. LINE STYLE Available options are Solid, Dashed, or Bracket. COLOR Sets the frame guideline color to White, Gray, Teal, Purple, Yellow, Green, Blue, Red, or Black. Select the color that provides maximum color contrast with the scene you are shooting. Default is White. TRANSPARANCY Sets the frame guide transparency. Available options are 0%, 25%, 50%, 75% and 100%.
BRIGHTNESS CONTROL Slide to the right for a brighter display; slide to the left for a dimmer display. TOUCH GESTURES These options apply ONLY to the Touchscreen LCD. Pinch to Magnify When selected, allows you to use two fingers in a pinching motion on the screen to enable Focus Zoom. To zoom out to normal view, slide fingers apart. Double-Click Right 25% to Record When selected, the right 25% of the screen can be double-tapped to start and double-tapped again to stop recording.
CONTRAST Adjusts the overall contrast of the image. Range is -1.0 (flat) to +1.0 (max contrast). Default is 0.0. BRIGHTNESS Adjusts brightness without crushing highlights. Available range is – 10.0 to +10.0. Default is 0.0. GAIN The GAIN sub-menu permits adjustment of RED GAIN, BLUE GAIN and GREEN GAIN. RED Adjusts the gain of the RED channel only. Range is 0.0 (no Red) to 10.0. Default is 1.0. BLUE Adjusts the gain of the BLUE channel only. Range is 0.0 (no Blue) to 10.0. Default is 1.0.
FLUT FLUT (Floating Point Lookup Table) adjusts mid-range tone values. Range -8.0 to +8.0. Default is 0.0. EXPOSURE Adjusts exposure compensation. Available exposure range is –7.0 to +7.0. Default is 0.0. SHADOW Shadow adjusts the toe value of the FLUT or in other words, the tone near Black. Range is -2.0 to +2.0. Default is 0.0. Increasing the Shadow value raises the video level of near Blacks. Lowering the Shadow value crushes the video level of near Blacks.
COLOR/GAMMA The COLOR/GAMMA sub-menu permits adjustment of the monitor output Color Space and Gamma curves. Available Color Space Options Available Gama Space Options 955-0003_v3.
PROJECT The project menu sets the operating parameters the camera will use for a given project. Options available are TIME BASE and TIME CODE. 112 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
TIME BASE Sets the TIME BASE (fps) to be used for the project - the primary acquisition frame rate, time code count and playback & editing frame rate. Setting is displayed in the lower left corner of VIEWFINDER output(s). Available options are 23.98, 24.00, 25.00, 29.97, 47.96, 48.00, 50.00, and 59.94. Default is 23.98. TIME CODE Selects the TIME CODE source to be used. Options are EXTERNAL TC and INTERNAL USERPROVIDED TC. 955-0003_v3.
TIME CODE DISPLAY Allows you to choose between TOD and Edge display. TIME CODE SOURCE Available options are EXTERNAL and USER-PROVIDED. User-Provided The three numerical boxes below allow you to set hours, minutes and seconds (in that order). Use RTC Time When selected the camera uses the cameras Real Time Clock as the timecode counter source (snapshot of the RTC.) Set Manually When selected allows the user to define a custom value as the timecode counter seed.
SLATE When selected, a new dialog box will appear allowing you to add properties to the media highlighted in the Current Media box when formatting. Available options are CAM ID, CAM POS and SET to set the values entered. Auto-Incrementing Take If there is a value entered in the Scene box, the camera will automatically increment the take number every time the camera starts and stops recording. Note: The scene name is limited to eight characters.
AUDIO/VIDEO Menu adjusts AUDIO INPUT, AUDIO OUTPUT, AUDIO CHANNELS, MONITOR CONTROL, and TEST SIGNALS. AUDIO INPUT Allows you to enable / disable and adjust levels for audio inputs (CAM ANALOG). Default is unchecked. Range 8 to 64 dB, default is 10 dB. 116 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
You can also directly input your desired audio levels. Audio channel level inputs are displayed in the lower section of the UI. When audio is enabled and an audio jack is plugged in (detected by the camera), the circle next to CH1, CH2 etc… will be Green and the box around the signal will be highlighted. When audio is enabled and an audio jack is not plugged in (not detected by the camera), the circle will be Red.
AUDIO OUTPUT Allows adjustment of audio output levels fed to the outputs. Available options for each channel are ON and MUTE. Default is ON at -9 dB. AUDIO CHANNELS Allows selection of audio inputs and operational modes. 118 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
INPUT Available inputs are CH 1/2 and CH 3/4. NOTE: For cameras not equipped with a PRO I/O module, options are CH 1/2. Source Available options are NONE, CAM ANALOG, PRO I/O ANALOG, PRO I/O AES A, and PRO I/O AES B. NOTE: For cameras not equipped with a PRO I/O module, options are NONE or CAM ANALOG. 955-0003_v3.
Mode Available options are UNBALANCED and BALANCED. Link Enables linkage between Channel Gain controls. Limiter Enables signal limiter circuit. Limiter enabled adds 10dB of headroom for Microphone level inputs, or 4dB for Line Level inputs. OUTPUT Link Enables linkage between Output Channel Attenuation controls. MONITOR CONTROL This sub-menu allows the monitor outputs settings to be modified. For changes to take effect, the camera MUST be restarted. 120 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
MODE Allows you to choose the output for the LCD/EVF, HDMI and HD-SDI monitors. LCD/EVF Options are MENUS, PREVIEW, CLEAN, OVERLAY, 3D LEFT, and 3D RIGHT. If anything other than MENUS is selected on the LCD (such as CLEAN), to return to displaying the MENUS, perform a double-tap on the LCD screen. HDMI Options are OFF, MENUS, PREVIEW, CLEAN, OVERLAY, 3D LEFT, and 3D RIGHT. RES Allows you to choose the output resolution for HDMI monitors. Available options are AUTO, 720p and 1080p.
RES Allows you to choose the output resolution for HD-SDI monitors. Available options are AUTO, 720p and 1080p. FREQ Allows you to choose the output frequency in Hertz (Hz) for HD-SDI monitors. Available options are AUTO, 23.976/24, 25, 29.976, 47.952/48, 50, and 59.94. AUTOMATICALLY ASSIGN MENU SCREEN IF ENABLED When checked will assign an attached external monitor to display the menus if none are selected. TEST SIGNALS Permits the video monitor outputs to be replaced with a video test pattern.
SETUP This menu permits a variety of system setup tasks to be accomplished. Options available are KEYS / SHORTCUTS, DATE / TIME, NETWORK, SERIAL, REMOTE, GPIO, and SYSTEM. KEYS Use Keys function to customize the assignment of DSMC camera controls. KEY MAPPING With Key Mapping, you press the button you want to change and follow on-screen instructions to complete the change. When the Key Mapping tab is highlighted: • Press the camera key you want to change.
OPTIONS • Select the desired option • Press menu or a blank area of the touchscreen to save the setting ADVANCED • The advanced tab allows you to set key functions using a series of pull down menus • Select Key Source (Brain, REDMOTE, Side SSD, etc.) • Select the key you wish to change • Select the desired key action Key Source 124 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
User Key Key Action WARNING: Do not remap the navigation keys (Up, Down, Left, Right, Select (Enter), or Menu) on the side handle doing so could render the camera inoperabel. 955-0003_v3.
DATE / TIME This menu allows the user to reset the battery backed up internal clock of the camera. This time value is used as a timestamp on the .R3D files when recording to the RED MAG 1.8” SSD media. NOTE: Enter time in 24-hour clock format. i.e. 2:35 pm should be entered as 14:35:00. COMMUNICATION Communication Menu allows you to set a unique identification for the camera (or a group of cameras) when operating in command and control communications network.
GROUP A camera can also be identified as a member of a GROUP of devices. (For example, a group "3DRIG_A" could include two cameras "CAM_A_L" and "CAM_A_R"). The default group is named "DEFAULT". Group names (like camera Names) can be used to uniquely address commands to a specific group of networked cameras. Note: the group name is limited to 8 characters, default name is DEFAULT.
NETWORK If the Gigabit Ethernet port is used, additional settings are required. Each camera or device requires a unique IP ADDRESS. For simple camera-to-camera communication via Ethernet, both cameras need to be in the same sub-net. Use the same sub-NETMASK and GATEWAY addresses and the first three groups of the IP address need to be the same. In the example below, two cameras two cameras are assigned to the group “3D RIG.” Note the IP Addresses.
REDMOTE This function is used to pair the camera to a REDMOTE for wireless operation. SCAN AND PAIR REDMOTES When selected, the camera will look for an attached REDMOTE, plus any REDMOTEs that are turned on with REDlink wireless enabled. Available REDMOTES will appear in the left window. The MAC Address for locally any attached REDMOTE will be in brackets <>. Use the Pair and Unpair buttons to select and Pair/ Unpair REDMOTES.
GPIO GPIO selects the GPIO preferences sub-menu. CAMERA INPUT Permits the function of the SYNC IN / GPI pin in the SYNC connector to be defined as: Sync In Accepts an Input Sync signal to control Shutter Start timing. General Purpose In Accepts an Input Trigger signal to act as a General Purpose Input. 130 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
CAMERA OUTPUT Permits the function of the SYNC OUT / GPO pin in the CNTL connector to be defined as: Sync Out Provides an Output Sync signal to act as a Shutter Start tally. General Purpose Out Provides an Output Tally to act as a General Purpose Output tally signal. 955-0003_v3.
SYNC MODE Allows the shutter timing (scan start) to be synced to an external signal. Available options are OFF, GENLOCK, SHUTTER, INTERNAL, PROXY, and SLAVE. Default is Off. OFF – Shutter start time is defined by internal camera timing. GENLOCK – Shutter start time is slaved to an external RS170A tri-level sync signal .a.k.a. “Genlock”. SHUTTER – Shutter start time is slaved to an external Shutter Sync signal. INTERNAL – Not implemented at this time. PROXY – Not implemented at this time.
SYSTEM Available options are FAN CONTROL, RECORD SPEED and STANDBY SPEED as well as BEEP SPEAKER and EVF TALLY LIGHT. FAN CONTROL Specifies cooling fan operation. Available options are AUTO and MANUAL. Manual will run the fan at the speeds specified in RECORD SPEED and STANDBY SPEED. Default setting is AUTO. Auto This setting selects VARIABLE speed fan operation in standby based on the camera core temperature.
INDICATORS Beep Speaker Available options are OFF and RECORD/STOP. When RECORD/STOP is selected, an audible beep will be heard when record is started and another when record is stopped. EVF Tally Light When checked, enables the Record Tally Red LED on the front of the EVF.
SYSTEM INFO When selected the Viewfinder output(s) will display the camera Model, current firmware Version, installed and camera P.I.N. SAVE LOG Select to write camera’s .LOG file to the REDMAG 1.8” SSD. The .LOG file is a diagnostic tool that can assist RED with camera troubleshooting. After capture, upload the .LOG file to the RED customer service team contactable at www.RED.com/support. After successfully writing the log file to media, viewfinder output(s) will display LOG SAVE COMPLETED.
CALIBRATION Sensor calibration is a process where the camera generates a calibration map to correct for pixel defects and offsets based on current system and environmental settings. This allows you to perform a Black Shading calibration of the MYSTERIUM X sensor two (2) different ways; Default (at 24 FPS @ 1/48 SEC) or using your current FPS/Exposure settings.
CURRENT CALMAP Calibration maps are stored in the camera. Due to the nature of the camera, different calibration maps are needed for different situations. Factory This the calibration map generated during production. This map is always present and selected as default on first use after performing a system restore under SETTINGS > MAINTENANCE > RESTORE SYSTEM. User HS The user can select the CURRENT CALMAP. The dialog only show the calmaps stored in memory (FACTORY and USER HS in this case).
BLACK SHADING PROCEDURE The calibration procedures are the same for both BLACK SHADING options. The calibration procedures are the same for both Black Shading (24 FPS @ 1/48 SEC) and Black Shading (Current FPS/Exposure) options. When selected, a screen will appear asking if you wish to proceed with Black Shading calibration. REDMOTE will also display the following messages. Black Shading calibration procedure: 1.
6. Once Analyzing is complete, a status screen will show progress of the Erasing step. 7. Once Erasing is complete, a status screen will show progress of the Programming step. 8. The camera will perform this procedure twice. 9. After Programming, CALIBRATION SUCCESSFUL will be displayed. Select OK to complete Black Shading calibration. SELF TEST When selected allows you to perform a self-test for the sensor and LCD Touchscreen. 955-0003_v3.
ENABLE / DISABLE SENSOR TEST PATTERN When selected enables / disables the sensor test pattern (White Screen). To turn on, select ENABLE SENSOR TEST PATTERN. To turn off, select DISABLE SENSOR TEST PATTERN. 140 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
TOUCHSCREEN When selected allows you to perform a touchscreen self-test. When the touchscreen self-test is on, you can verify all areas of the touch screen respond to touch. Simply touch each box using your finger. The touchscreen responds to the touch and the Green box turns Blue. To exit the Touchscreen Self-Test: • Place your finger on the touchscreen and hold it there until the main screen appears. • Press the Enter or Menu button on the Side Handle or REDMOTE.
When selected, you will be asked to confirm if you want to delete all settings and restore the factory default settings. After settings are restored, “DEFAULT SETTINGS RESTORED, INITIALIZING RESTART…” Camera will automatically power down and will require you to manually power it up. NOTE: User key settings will be reset as well as any other changes from the cameras default settings. The REDMOTE will also require paring to communicate wirelessly with the camera.
MOTION SENSOR CALIBRATION The RED DSMC Camera displays data from the accelerometer to help orient the camera. After a firmware upgrade or Factory Restore the motion sensors need to be re-calibrated through the Maintenance->Motion Calib menu." 955-0003_v3.
PLAYBACK Playback allows you to view clips on media currently attached to the camera. It also allows you to change the look of the playback clips be changing settings available when in playback mode. NOTE: SCARLET-X™ menus shown, EPIC menus similar. UPPER CONTROLS From Left to Right are ISO, WHITE BALANCE, VIEW, PRESETS, MEDIA, SEETINGS, and META. Below the settings is the clip playback status bar. Exit Playback ICON (Touchscreen) Select the O on the Left to exit Playback mode.
WHITE BALANCE Allows you to change the White Balance in the clip during playback. Advanced Menu Opens the advanced White Balance settings without the ability to Calculate. VIEW Allows you to select the items to be displayed in the playback window. Available options are Center, File Name, Time Code, Frame Guide, Action Guide, and Title Guide. 955-0003_v3.
PRESETS Allows you to apply presets to the clip during playback. MEDIA When selected will list all available clips on the attached media. 146 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
Touchscreen 1. Double-Tap the desired clip to open in the playback window. 2. Load will also highlight. You can also select LOAD to load the clip in the player and allow playback. Side Handle / REDMOTE 1. Select the desired clip to playback and press the ENTER button. 2. Load will highlight. Select LOAD to load the clip in the player and allow playback. 955-0003_v3.
SETTINGS Available options are DISPLAY, LOOK and RECORD. Display Available options under Display are TOOLS and ZEBRA. Tools Allows you to toggle ON/OFF Exposure, Focus, Video, Edge, and RAW. Refer to SETTINGS MENU > DISPLAY > TOOLS for complete details about these options. Zebra Allows you to toggle ON/OFF Zebras. Refer to SETTINGS MENU > DISPLAY > ZEBRA for complete details about these options. 148 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
Look Allows you to adjust the Color, Gain, FUT, and Curve of the image during playback. Refer to SETTTINGS MENU > DISPLAY > LOOK for complete details about these options. Record (Exit) When selected will exit playback to the main menu. META Displays current clip META information. 955-0003_v3.
CLIP PLAYBACK STATUS BAR Displays the progress of the clip during playback. Touchscreen When using the touchscreen you can swipe your finger Left or Right to open and allow playback of the previous or next clip on the media. Side Handle / REDMOTE When using the Side Handle or REDMOTE you can use the navigation group to highlight the clip playback status bar.
LOWER CONTROLS From Left to Right, PLAYBACK SPEED, IN POINT MARKER, FRAME-BY-FRAME REVERSE, PLAY/PAUSE, FRAME-BY-FRAME FORWARD, OUT POINT MARKER, PLAY ONCE/LOOP, and PLAYBACK DIRECTION RESOLUTION / PROJECT FRAMERATE / QUALITY Display clip Resolution, Framerate and Quality (REDCODE). When using the touchscreen, touch the Resolution, Framerate and Quality (REDCODE) to display the METADATA for the clip. HISTOGRAM Displays the clip histogram.
IN / OUT POINT MARKER Allows you to set In and Out Points during clip playback. This allows you to playback only a certain portion of the clip as desired. Helps when the clip is rather long and you want to focus on a particular segment. The In (Red) and Out (Green) points will be displayed in the Clip Playback Status Bar. You can use the navigation group to select the exact location of the In and Out Points if desired.
PLAYBACK DIRECTION Allows you to play the clip forward or backwards. Reverse playback is shown. ADDITIONAL CLIP/CAMERA INFORMATION Will indicate if clip was recorded in HDRx and current camera power status as well as audio input signals. POWER The power menu displays the current power status of all attached power sources as well as allows you to shutdown the camera. POWER STATUS The power status is displayed for the BRAIN, SIDE HANDLE, REAR 1, REAR 2, REAR 3, and REAR 4.
SHUTDOWN Power OFF controls are interlocked to prevent accidental powering down of the camera. For details on the different ways to power down your RED DSMC Camera, refer to BASIC OPERATION > POWER DOWN. 1. Enter the Secondary Menu using the touch screen, REDMOTE or Side Handle. 2. Select POWER. 3. Select SHUTDOWN. 4. The camera will immediately power down displaying SHUTTING DOWN…. If a REDMOTE is connected, the same message will display. 154 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
APPENDIX A: UPGRADING CAMERA FIRMWARE Your RED DSMC camera functionality may be upgraded by installing the latest firmware. Camera firmware is identified by Version and SVN number, which will be displayed by the camera on the LCD display when SYSTEM INFO is selected. A higher number reflects a later release. Make a habit of frequently visiting www.RED.com/support to check for later versions of camera firmware, Operations Guide updates, and post-production software.
APPENDIX B: MANAGING DIGITAL MEDIA MEDIA REDMAG 1.8” SSD is available with capacities of 64GB, 128GB or 256GB. Record duration is dependent on resolution, quality and frame rate, but a 64GB SSD will typically provide 24 minutes of 24fps 5K RAW recording. On MAC computers with REDCINE-X PRO installed, RED Watchdog will mount the SSD as “READONLY” by default and you cannot write the firmware to the SSD. RED Watchdog is identified by the RED Coin icon located on the Right side of the Menu Bar.
- On REDMOTE, NONE will be displayed twice (as opposed to when no media is inserted, the GUI displays NONE with three dashes below “---“). - On the Side Handle, NA will be displayed (same as if no media is present). 3. To format the media select SECONDARY MENUS > MEDIA > FORMAT MEDIA. 4. You will be prompted to set the media and select FORMAT. - Viewfinder output(s) will display “FORMATTING”. NOTE: If when selecting FORMAT, the display indicates FORMAT FAILED, refer to MEDIA ERRORS. 5.
MEDIA CAPACITY REMAINING STATUS The Viewfinder output(s) will display the remaining media capacity in the MEDIA indicator (100% is shown). At 10%, remaining capacity the media status will turn yellow, at 5% it will turn red. At 2%, remaining the camera will cease recording. This reserves a small amount of capacity for ancillary data to be written to the media. NOTE: When media is full, the Side SSD LED will flash Red.
3. When media is ejected, Viewfinder output(s) will display “MEDIA EJECTED SUCCESSFULLY“. 4. Media can now be removed from the camera. USING SIDE HANDLE 1. By default, the lower of the three (3) SYSTEM KEYS is set to Eject Media when pressed. 2. When media is ejected, Viewfinder output(s) will display “MEDIA EJECTED SUCCESSFULLY“. 3. Media can now be removed from the camera. USING SIDE SSD 1. Press both User Keys 1 and 2 at the same time to eject REDMAG 1.8” SSD Media. 2.
ERASING MEDIA NOTE: If the media was formatted using SECURE FORMAT, you cannot erase the media using an external source. Erasing of the media must be performed by formatting on the camera. MACINTOSH OS X 1. Connect the REDMAG 1.8” SSD via RED STATION REDMAG 1.8". 2. Open the Disk Utility. 3. Carefully choose the drive from the list on the left. 4. Select the Erase tab. 5. Choose MS-DOS (FAT) as the Volume Format. You can add a Name if desired, however the camera will overwrite this.
APPENDIX C: INPUT / OUTPUT CONNECTORS CAMERA BRAIN FRONT Shown with PL Mount installed. B A A MIC-1 3.5mm Audio Jack B MIC-2 3.5mm Audio Jack Camera Brain Connectors - Front 955-0003_v3.
MIC-1, MIC-2 (MICROPHONE AUDIO) Two 3.5mm phone jacks on the front of the brain support two independent channels of balanced or unbalanced microphone level analog audio inputs.
CAMERA BRAIN REAR G A D B C A E A HD-SDI B Headphone C SYNC (Video Sync) D CTRL (RS232 Control) E GIG-E (Ethernet) F DC IN (Power Input) G HDMI Camera Brain Connectors - Rear 955-0003_v3.
HD-SDI A standard 75 Ohm BNC connector provides a broadcast specification high definition video output. PIN SIGNAL DESCRIPTION DIRECTION Center HD-SDI SMPTE-292M HD-SDI Out Shield/Screen GROUND Camera ground -- HD-SDI Output The HD-SDI output provides a 720p progressive scan video feed operating at 50.00 or 59.94 Hz or a 1080p 10-bit 4:2:2 progressive scan video feed operating at 23.98, 24.00, 25.00 or 29.97 Hz when in 1.
HEADPHONE A 3.5mm stereo jack provides two channels of adjustable level analog audio for monitor headphones. A C B Headphone Output Connector PIN SIGNAL DESCRIPTION DIRECTION A (TIP) LEFT Left channel audio Out B (RING) RIGHT Right channel audio Out C (SLEEVE) GND Camera ground -- The camera’s four audio channels may be monitored in pairs: either 1L - 2R or 3L - 4 R or as a quad mix of 1+3L – 2+4R based on the MIX parameter. Default is 1L-2R. Output volume may be adjusted as follows.
The Video Genlock input may be used as a vertical interval reference signal for the sensor and HD-SDI outputs when precise synchronization is required between cameras, such as for 3D and live broadcasts. Note: When GENLOCK is selected as the sensor shutter reference, shutter start timing (SHUTTER PHASE) may still be adjusted. HD-SDI monitor outputs will automatically sync to the external GENLOCK signal as soon as it is detected, there is no need to enable this function.
NOTE: A pre-fabricated SYNC interface cable is available from RED Digital Cinema. • P/N 790-0154 – Video Sync – Camera to 3 BNC – 3 ft. (1m) • White BNC: Shutter Sync / GPI • Yellow BNC: SMPTE Timecode • Green BNC: RS170A Genlock 955-0003_v3.
CTRL (RS232 CONTROL) A 4-pin LEMO connector supports RS232 remote control for 3D camera communication, and third party metadata ingest applications. The shutter Sync Output signal acts as an immediate response hardware tally of a scan. This is useful for 3D or motion control applications where a slave camera or lighting device needs to be synchronized to a master camera. Alternatively, this output pin may be used as a GPO (General Purpose Output) tally, whose function is programmed in the USER KEYS menu.
GIG-E (ETHERNET) A 9-pin LEMO connector provides a Gigabit Ethernet port for remote camera setup, master / slave camera communication and external metadata ingest. View into Ethernet Interface connector Mating connector: FGG.0B.309.
DC IN (POWER INPUT) The 6-pin LEMO connector accepts DC input power between +11.5 V and +17 V DC. Power conditioning provides protection against reverse-polarity connection, ESD, under and over voltage, and over current. View into camera DC IN Power Input connector Mating Connector: PIN 1 2 3 4 5 6 LEMO FGJ.1B.306.CWLD72Z SIGNAL DESCRIPTION +VBATT Power input, +11.
HDMI OUT The HDMI output supports an HDTV and PC monitor compatible 10-bit 4:2:2 progressive scan video signal (with embedded audio) at 720p and 1080p resolution. The HDMI output may be specified as a PROGRAM output (clean feed video) or as a PREVIEW output (including SurroundView™ look around, Clip Name, Timecode and Safe Action / Safe Title frame guides). In addition to video data, the HDMI output also provides 4 channels of embedded audio. NOTE: Default setting is PREVIEW.
SIDE SSD MODULE B REAR FRONT A A SSD Slot B VIEWFINDER (LCD/EVF) Side SSD Module The Side SSD Module mounts to the left side of the camera Brain. On the rear face of this module is a slot for inserting a REDMAG 1.8”SSD digital Magazine. Do not attempt to insert any other media type, or any foreign objects into this slot, as damage to the Side SSD Module and / or the camera Brain may occur.
REDMOTE This section describes the physical connectors on the REDMOTE. B A A Mini USB B Camera Interface REDMOTE Connections The REDMOTE interface connector allows communication between the REDMOTE and the camera Brain or any expansion module. Make sure these contacts are kept clean and free of any contaminants that may interfere with a reliable electrical contact. 955-0003_v3.
APPENDIX D: DEFAULT KEY FUNCTIONS CAMERA BRAIN KEY FUNCTION KEY FUNCTION Record Half Press Key Disabled- Record Half Release -Key Disabled- Record Full Press Record: Toggle SIDE HANDLE 174 KEY FUNCTION KEY FUNCTION User A Press AF Mode: Cycle User B Release -Key Disabled- User B Press WB: Auto Calc User C Release -Key Disabled- User C Press Magnify: Toggle User D Release -Key Disabled- User D Press Exposure Check: Toggle User 1 Release -Key Disabled- User 1 Press Slot: Set I
SIDE SSD MODULE KEY FUNCTION KEY FUNCTION User 1 Press -Key Disabled- User 1 Release -Key Disabled- User 2 Press -Key Disabled- User 2 Release -Key Disabled- User 1+2 Press Eject Media Record Half Release -Key Disabled- Record Half Press AF: Start Record Full Release -Key Disabled- Record Full Press Record: Toggle REDMOTE KEY FUNCTION KEY FUNCTION User A Press Navigation: Select AF Mode: Cycle Nav Enter Press User B Press RAW Check: Toggle Rocker + Press Iris: Open User C P
APPENDIX E: REDMOTE OPERATION CONTROL, CONNECTORS AND DISPLAY This section describes the REDMOTE physical controls, connectors and color LCD display.
LEDS There are two status LED indicators located above the rockers switch on the left side of the LCD display. The upper LED is used to signal camera readiness and camera record status. • Red – Camera Startup / Camera Recording. The lower LED is used to signal camera readiness and REDMOTE communication status to the camera. • Green – Camera Ready / REDMOTE connected.
C A B REDMOTE Navigation Group A B Scroll Wheel Direction Keys C Enter Button The Navigation Group has three separate operational capabilities. SCROLL WHEEL The Scroll Wheel allows the operator to select and adjust the values of selected camera parameters. DIRECTION KEYS The Direction Keys allows Left / Right / Up / Down navigation thru the camera menus to select a desired parameter for adjustment.
SOFT MENU BUTTONS 4-8 To the right of the LCD are five Soft Menu Buttons. These buttons select a variety of camera status pages. For complete information refer to OPERATION > REDMOTE MENUS > SOFT MENU BUTTONS 4-8. Note: In Version 3.x software, Soft Menu Buttons 7 and 8 are undefined.
Note: For illustration only: rear surface of REDMOTE should face towards camera 2. Slide the REDMOTE down until a click is heard which indicates the REDMOTE is securely attached. UNDOCKING 1. Depress the two latch release buttons located on each side of the REDMOTE. 2. Slide the REDMOTE upward to release from the V-Mount of the camera Brain / rear most module. 3. Remove the REDMOTE. POWER UP / DOWN Located on the upper right side of the REDMOTE is the Power / Key Lock Switch (refer to CONTROLS).
POWER UP CONNECTED TO CAMERA If the REDMOTE is physically attached to a camera, when the camera is powered up the REDMOTE will automatically power up along with the camera. NOT CONNECTED TO CAMERA To manually power up the REDMOTE, slide and hold the Power / Key Lock Switch in the down direction for 2 seconds, then release. POWER DOWN USING CAMERA When REDMOTE is connected to the camera and the camera is powered down, the REDMOTE will also power down.
RECORDING • To record, press the Red REC (record) button. If media is connected and properly formatted, the upper LED will illuminate Red and the Timecode value displayed in the LCD will change to Red text. To stop recording, press the REC button a second time. After recording to media is completed, the upper LED will go out and the Timecode value displayed in the LCD will change back to White text.
CHANGING CAMERA SETTINGS USING CAMERA LCD / EXTERNAL MONITOR AS REFERENCE To adjust a parameter value displayed on the camera’s Upper Status Group, first note the red colored bar (located under 24fps in this example), indicating the currently active parameter for instant adjustment. Use the NAVIGATION GROUP directional pad to move the cursor to a different parameter if desired, then press the ENTER key to select that parameter and use the Scroll Wheel to adjust that parameter’s value.
ADVANCED OPERATION: REDMOTE MENUS SOFT MENU BUTTONS 1-3 Located below the main LCD display are three Soft Menu Buttons, who access advanced function menus identified by text in the LCD directly above the corresponding button. These menus control wireless connection (CONNECT), camera or local menus (REMOTE/LOCAL) and system setup (SETUP). WIRELESS CONNECT: SOFT MENU BUTTON 1 Note: This Button is hidden if REDMOTE is attached to the camera or rear-most camera module.
4. Select the desired camera to connect to for REDMOTE wireless operation and press the ENTER button in the Navigation Group. The REDMOTE will connect to the selected camera. 5. Once connected, the REDMOTE will display the key operating parameters of the selected camera. The wireless signal strength will be shown in the lower Right corner of the REDMOTE screen.
Note: Once this procedure has occurred once, the REDMOTE will automatically search for the camera each time it is undocked, until the paired camera selection is changed. CANCEL If you wish to exit the CONNECT menu at any time press CANCEL. 186 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
DISCONNECT To stop communicating wirelessly with the camera, select Soft Menu Button 1 Connect, then select DISCONNECT and press the ENTER key in the Navigation Group. RECONNECTING IF SIGNAL IS LOST On loss of wireless communication REDMOTE will scan for the camera it was last paired with. If the REDMOTE is unable to re-connect after 30 seconds, it will enter the manual SCAN menu, follow the procedure outlined about to scan and identify camera(s) that you wish to connect to. 955-0003_v3.
OPERATING WITH MULTIPLE CAMERAS FROM A REDMOTE To control more than one camera from a single REDMOTE, first pair the REDMOTE with each camera. After pairing REDMOTE to the desired cameras, press Soft Menu Button 1: CONNECT. Available cameras will be listed. Select the camera you wish to control and press the ENTER button. When you want to switch to a different camera, press Soft Menu Button 1: CONNECT again to list available cameras and re-select.
REMOTE Allows the user to adjust camera settings from REDMOTE, by navigating the camera menus appearing on the VIEWFINDER output of the camera, with summary data only appearing on the REDMOTE LCD LOCAL Allows the user to adjust camera settings from REDMOTE, by navigating camera menus appearing on the REDMOTE LCD, with summary data only appearing on the VIEWFINDER output of the camera. CUSTOMIZING LOCAL MENUS.
6. Select “Setup Slot” and press the ENTER button. 7. A new Setup window will appear displaying available parameters to display. 8. Select the desired parameter and press the ENTER button. 9. You may now control this parameter directly from the REDMOTE. REDMOTE SETUP: SOFT MENU BUTTON 3 When pressed, SETUP provides the option of forcing the REDLINK wireless link ON or OFF and selecting the following REDMOTE Setup menu. 190 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
Adjustable parameters include LCD screen brightness; beep speaker Volume and Auto Shutdown time. In the lower section of the display is the MAC address and the current firmware build of the REDMOTE Brightness The BRIGHTNESS control adjusts the LCD backlight intensity. Set value to maximum for daylight visibility, set value lower for nighttime operation or for maximum battery run time when operating in wireless mode. Default value is Maximum.
MAINTENANCE INTERNAL BATTERY CHARGE STATUS An icon shows the charge status of the REDMOTE battery in the lower right corner of the LCD. When REDMOTE is operating in wireless mode, the icon indicates current charge capacity. When satisfactory the icon is displayed in Green. When battery charge becomes marginal, the icon turns Yellow. When battery charge is critically low, and wireless communication is at risk of being lost the icon turns Red.
CHARGING CHARGE TIME A fully discharged REDMOTE battery will be fully charged in approximately 6 hours. USING CAMERA While connected to the camera, the REDMOTE will automatically recharge its internal battery. Charge status is indicated by the Green Battery Icon at the top-right of the REDMOTE LCD display screen. A fully discharged REDMOTE battery will be re-charged in approximately 6 hours if connected to a powered camera or a USB based power source such as laptop P.C.
UPGRADING REDMOTE FIRMWARE The REDMOTE update utility allows you to upgrade the firmware on your REDMOTE. NOTE: After firmware has been upgraded, the REDMOTE must be paired to the camera again. SETUP CONFIGURING REDMOTE CONNECTION WITH COMPUTER (MAC) The first step in upgrading REDMOTE firmware is to establish communication between the MAC and the REDMOTE. 1. Connect a USB to mini-USB cable between the computer and the USB connector on the REDMOTE. 2. Go to System Preferences and choose Network.
NOTE: After entering the IP address as shown above you may not connect during the upgrade procedure. When you go back and check the IP address you see that it is 0.0.0.0 HOWEVER the status of the device is shown as “Connected”. If this is the case, you may need to enter the IP address a second or possibly a third time to make it stick. 8. Click “Apply’ at the bottom of the Network window. 9. Proceed to UPGRADING REDMOTE FIRMWARE.
7. Click “Connect”. When REDMOTE has been established, “Connection to REDMOTE has been achieved” will be displayed. NOTE: If REDMOTE does not connect, verify that the IP address set under CONFIGURING REDMOTE CONNECTION WITH COMPUTER (MAC) has held. If not, enter it again as outlined in the procedure. 8. Click "Select File" and navigate to the redmote.1.bin file located in the REDmote_firmware_vXXX folder. 196 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
9. Select "Start upgrade". 10. File transfer status will be displayed as a Blue bar. 11. “Updating Firmware” will be displayed with a Green status bar showing upgrade progress. REDMOTE will also display UPGRADE during this process. 955-0003_v3.
12. Once the File Transfer Status is completed, the REDMOTE Software Wizard will display “Please Wait and Don’t Unplug – Firmware Upgrade is in Progress on REDMOTE”. 13. After a few more seconds, the REDMOTE Software Wizard will display “Firmware Upgrade Successfully Done”. Select OK. 14. The REDMOTE Software Wizard will disconnect from the REDMOTE. 15. REDMOTE will reboot. 16. REDMOTE upgrade is complete. REDMOTE will display “POWER UP”, then “SEARCHING” once the upgrade has completed.
17. Verify the current REDMOTE firmware version by selecting SETUP > SETUP SYSTEM on the REDMOTE. 18. REDMOTE upgrade is complete. You can now reconnect to the camera. NOTE: Pairing of the REDMOTE may not be necessary after upgrading the REDMOTE firmware, however after upgrading the camera firmware, you must pair the REDMOTE again. WINDOWS Install Upgrade Utility This procedure outlines installation of the REDMOTE Upgrade Utility for Windows computers. 1.
5. Select “I Agree” to the license agreement. 6. On the Choose Components screen, select Install REDMOTE Firmware. 7. Select “Next”. 200 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
8. Choose location to install the REDMOTE Upgrade Utility . 9. Choose the location for the shortcut. 955-0003_v3.
10. The program will now install. A progress bar is displayed while installing. When complete, select Close. 11. The REDMOTE Upgrade Utility installation is complete. Upgrading REDMOTE Firmware The following information will guide you through proper upgrading of your REDMOTE firmware on Windows computers using the REDMOTE Upgrade Utility. 1. Connect a USB to mini-USB cable between the computer and the USB connector on the REDMOTE. 2.
NOTE: If when connecting, communication is not established quickly, close the Upgrade Utility, open it again and select Connect again. This may have to be repeated a few times until communication is established. 6. When connected, ”Connection is Established with REDMOTE” is displayed. 7. To begin upgrade, click on “Select File”. 8. Navigate to the *.bin file for updating the REDMOTE firmware. NOTE: If you choose an incorrect file, click on “Select File” again to locate the correct file.
9. The selected file is shown in the window. In this case the selected file is: REDmote.1.bin. 10. After selecting and verifying the correct file for upgrading the REDMOTE, select “Start Upgrade”. 11. During the upgrade, the REDMOTE Software Wizard will display “Please Do Not Unplug” as well as a status bar showing “File transfer progress.” 12. During the upgrade, the REDMOTE will display “Upgrading Firmware” as well as a status bar showing upgrade progress.
13. When upgrade is complete, the REDMOTE will automatically reboot and display “REBOOTING” on the screen. 14. The REDMOTE Software Wizard will display “Firmware Upgrade Successfully Done”. 15. Verify the current REDMOTE firmware version by selecting SETUP > SETUP SYSTEM on the REDMOTE. 955-0003_v3.
16. Select “Disconnect” on the REDMOTE Upgrade Utility. 17. REDMOTE firmware upgrade is complete. 206 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
APPENDIX F: 3D SETUP / OPERATION OVERVIEW The following information outlines basic procedures to connect two RED DSMC cameras together in a Master / Slave configuration for 3D operation, operation of cameras in Master / Slave configuration and clip naming conventions for clips recorded on those cameras. The MASTER camera will control only the METADATA parameters of both cameras. On the SLAVE camera, any other setting outside of these will need to be manually changed before recording.
SLAVE CAMERA Perform the following steps on the Slave camera: 1. Go to SECONDARY MENUS > SETTINGS > SETUP > COMMUNICATION > NAME and give the camera a unique NAME (CAM B, RIGHT, etc…). 2. Under TARGET select NONE. 3. Give the Slave camera a unique IP address different from the Master. CLIP NAMING CONVENTIONS REEL NO. / SLATE (CAMERA ID) / CAMERA POSITION Before shooting in Master / Slave or Master / Master configuration for a Stereo / 3D production, make sure the Camera Slate (i.e. Reel No.
For example, if Master is set to LEFT and Slave is set to RIGHT and both Cam IDs are set to S, the first clip recorded by this stereo camera configuration will be: - Master: S001_L001_0503B6.R3D - Slave: S001_R001_0503R7.R3D Where 0503 represents 05 March, B6 and R7 are examples of camera generated wildcard characters.
• Green BNC connector is for Tri-Level Sync (Genlock) input. • White BNC connector is a dual-purpose (Shutter SYNC input or GPI) input. 4. Go to SETTINGS > SETUP > GPIO/SYNC > SYNC MODE and select GENLOCK. 5. Verify the camera’s project frame rate matches the Genlock and Timecode generator(s) framerate(s). 6. When properly connected and synchronized, TC, GEN and SYNC will illuminate Green on the UI.
APPENDIX G: EXPOSURE – USING FALSE COLOR AND ISO NOTE: The following section uses a RED ONE camera display to illustrate exposure tools; however, the same principles apply to RED DSMC camera systems. RED DSMC cameras provide several advanced exposure indication tools. In the following examples, we will show how these tools respond to a reference scene that is under-exposed, over-exposed and then correctly exposed.
ISO 800 - False Color: Exposure Select False Color – Exposure: note the√ E icon in the GUI when active. This mode allows us to visualize where in the image underexposure is taking place. These areas are indicated in purple. It is clear those areas are under the matchbox and coin, and between the bottle and cigar holder. ISO 800 - False Color: Video 212 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
Select False Color – Video: note the √ V icon in the GUI when active. This mode allows us to check the RGB video levels of the scene. As the peak white chips on the test chart are showing up in green and the underexpose areas are showing up in dark blue, this says the monitor path video levels are only ranging between 44 IRE and 1 IRE. Because the scene is under exposed, when the recorded .
ISO 800 - False Color: Exposure Select False Color – Exposure: note the√ E icon in the GUI when active. This mode allows us to visualize where in the image over exposure is taking place. These areas are indicated in red. It is clear those areas are on the highlight on coin, and at the top right edge of the color chip test chart. 214 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
ISO 800 - False Color: Video Select False Color – Video: note the √ V icon in the GUI when active. This mode allows us to check the RGB video levels of the scene. As all the white chips on the test chart are Yellow, this suggests that a significant portion of the monitor path video is at the maximum legal 100 IRE value. Because the scene is over exposed, when the recorded .
APPROPRIATE EXPOSURE ISO 800 - Monitor Output In this image, the camera is appropriately exposed for this scene. The monitor is neither very dark nor very bright and the histogram is spread evenly given that there are bright highlights on the coin we wish not to blow out. Note that there is no red bar on either the left or the right edges of the histogram and the vertical color stack to the right of the histogram is at yellow.
ISO 800 - False Color: Exposure Select False Color – Exposure: note the√ E icon in the GUI when active. This mode allows us to visualize where there is under exposure (purple) or over exposure (red) in the image. In this case, there is a very small area of purple under the cracker box, and just a suggestion of red on the highlight on the coin, which suggested that the sensor is appropriately exposed for this scene. 955-0003_v3.
ISO 800 - False Color: Video Select False Color – Video: note the √ V icon in the GUI when active. This mode allows us to check the RGB video levels of the scene. The two green squares in the upper right corner of the color chart and green in the background indicate that the scene’s mid grey and skin tone elements, plus peak white and blacks are all at appropriate levels.
ADJUSTING THE ISO RATING In the following two examples, the image exposed at ISO 800 rating have had the ISO rating adjusted first to ISO 6400 and then to ISO 100. NOTE: Although the image and Histogram both adjust to changes in the ISO rating, the sensor RAW meters do not change – they always indicate what is happening at the sensor level and hence where the image is truly in noise or at clipping. ISO 6400 - No Exposure Adjustment 955-0003_v3.
ISO 100 - No Exposure Adjustment In these extreme examples, it is clear that the RGB domain images are respectively very bright and very dark. The histogram data reflects that, however you can also see that the sensor RAW meters are unchanged. The exposure at the sensor at this point in time is the same. If you choose to close the iris to reduce the brightness of the first image you will be reducing exposure at the sensor – this biases exposure in favor of protecting the scene highlight.
APPENDIX H: POST PRODUCTION RED workflow is quite easy to understand, especially if you have experience with photographic RAW image processing, or shoot 16mm or 35mm film followed by a telecine transfer to video for non-linear video editing and on-line conform. The RAW data captured by RED cameras has wide dynamic range and color space, so you can freely change the white balance, adjust exposure and alter highlight and shadow tonality in post-production.
REDCINE-X® PRO REDCINE-X PRO is available for Intel based Mac OSX and Windows XP platforms. The application performing white balance and one light color correction, image pan/scan, crop and scaling operations. The application can export either a single clip, or a sequence of clips, as 4K or 2K resolution 10-bit DPX or 16-bit TIFF files. REDCINE-X PRO can also render clips into standalone QuickTime movies using a variety of video codecs including H.
APPENDIX I: MAINTENANCE WARNING: DO NOT attempt to modify, dismantle or open your camera, lens or other accessory as doing so may expose you to electric shock and serious injury. There are no user-serviceable parts inside. Alteration or repairs made to the camera, lens or other accessory, except by a RED authorized service facility, will void the Limited Warranty. CLEANING All RED products are designed for rugged durability, but precision instruments demand proper care.
DO NOT USE any other solvents, chemicals or third party cleaning kits because they have not been tested on RED TOUCH LCD displays and can possibly damage them. Not approved for use on RED TOUCH LCD displays: • Rubbing Alcohol • Isopropyl Alcohol (<90%) • Windex • Pre-packaged lens cleaner containing any additives, such as detergent, anti-static, fragrance, etc. For proper cleaning and storage, remember to protect the RED TOUCH LCD by storing it in the RED Microfiber bag.
BACK FOCUS ADJUSTMENT WARNING: THERE IS A SCREW-IN METAL PLUG INSTALLED IN THE CAMERA BODY COVERING THE BACK FOCUS SCREW. THIS PLUG MUST BE REMOVED BEFORE TO PERFORMING A BACK FOCUS ADJUSTMENT. TO REMOVE THE PLUG, USE A T-10 TORX SCREWDRIVER. NOTE: To be able to perform this procedure as written, you must have a PL mount and RED Focus™. Back focus is adjusted by turning the back focus adjustment on the top of the camera’s front plate using a T-10 Torx screwdriver.
RED Focus Properly Installed on Camera 4. Power up the camera. 5. Power up RED Focus. Refer to POWER UP / DOWN. NOTE: Remember that RED Focus will AUTOMATICALLY power down after 3 minutes. Press the Red button on the front to power back up. 6. Set the camera to Magnify. Go to SECONDARY MENUS > SETTINGS > DISPLAY > FALSE COLOR > MAGNIFY. NOTE: The “Focus” option located under SECONDARY MENUS > SETTINGS > DISPLAY > FALSE COLOR > FOCUS can serve as a good double-check for proper focus during this procedure.
- Turning COUNTER-CLOCKWISE moves the sensor rearward. NOTE: The center of the image will never be in perfect focus as the lines are less than 1/3 of a pixel in size. 9. The back focus adjustment mechanism is self-locking, and does not require a supplementary locking screw. 10. Install the screw-in plug in the back focus adjustment opening using a T-10 Torx screwdriver. 11. This completes the back focus adjustment. 955-0003_v3.
APPENDIX J: TROUBLESHOOTING NO MEDIA ATTACHED Displayed if media is not present or not formatted when pressing the record button. Connect media to camera if necessary. If media is already connected, format media and attempt to record again. Refer to APPENDIX B: MANAGING DIGITAL MEDIA for detailed information. RECORDING HALTED: RECORD ERROR - SHUTDOWN Displayed if media removed while recording. DO NOT remove media while camera is recording.
APPENDIX K: TECHNICAL SPECIFICATIONS SENSOR 14 MEGAPIXEL MYSTERIUM-X™ PIXEL ARRAY 5120 (h) x 2700 (v) DYNAMIC RANGE 13.5 stops, up to 18 stops with HDRx™ 6 fps with 5K FF and HDRx On 12 fps with 4K HD and HDRx™ On MAX IMAGE AREA 5120 (h) x 2700 (v) LENS COVERAGE 27.7mm (h) x 14.6mm (v) = 31.
CAMERA BRAIN DIMENSIONS Dimensions shown in mm Front View 230 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
Side View 955-0003_v3.
Top View Bottom View 232 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
Rear View 955-0003_v3.
APPENDIX L: RESOLUTION CHART 234 COPYRIGHT © 2012 RED Digital Cinema 955-0003_v3.
APPENDIX M: MENU MAPS 955-0003_v3.
IS 800 250 to 12800 ISO Varies WILL VARY BY ATTACHED LENS * Visible ONLY with RED EPIC Canon EOS Mount AND Canon EF / EF-S Lens 1/48 SEC 1/24 to 1/8000 SEC BASIC HDRx DISK PRESETS SELECT EXTERNAL MEDIA PRESET > IMPORT TO CAMERA CAMERA PRESETS SELECT ON-CAMERA PRESET > EXPORT TO EXTERNAL MEDIA SELECT VALUES: Image Project Output System Keys CREATE NEW PRESET CREATE SELECT RMD FROM EXTERNAL MEDIA AND SELECT APPLY RMD PRESET IMPORT/EXPORT TM SCARLET-X TITLE: DELETES DI
99 108 FOCUS 75 TO 107 EXPOSURE LOW IRE 93 TO 109 Center BLUE 1.000 0.0 TO 10.0 VIDEO 47 1 TO 99 EDGE 44 0 TO 84 LOW IRE Look Around: TRANSPARANCY % / COLOR: File Name Lens Info Time Code SHOW: AF Zones Grid OVERLAY 0.000 -10.0 TO 10.0 BRIGHTNESS HIGH IRE DISABLED BY DEFAULT DISABLED BY DEFAULT HIGH IRE ZEBRA 2 ZEBRA 1 ZEBRA 0.000 -1.0 TO 1.0 1.000 CONTRAST 1.000 1.000 0.00 TO 4.0 GREEN 0.0 TO 10.0 RED GAIN LOOK GO TO SHEET 1 OF 4 EXPOSURE 0.0 TO 10.
- 0 + 0 0 TO 59 SECONDS + USER PROVIDED External EXTERNAL USER-PROVIDED 10dB TM SCARLET-X ON / -9 dB LINK CAM None NONE MODE LIMITER PRO I/O LINK OUTPUT AUTO 1080p FREQUENCY Auto AUTO 23.976/24Hz 25Hz 29.976Hz 47.952/48Hz 50Hz 59.94Hz ©2012 RED.COM, INC. 1080p 720p A REV AUTOMATICALLY ASSIGN MENU SCREEN IF ENABLED PLAYBACK * HDMI and HD-SDI cannot be enabledat the same time. Camera MUST be restarted for changes to take effect. SHEET 3 OF 4 VERSION: 3.
LOOK FOCUS Refer to Operation Guide USER KEY Refer to Operation Guide KEY ACTION SCARLET-X CALIBRATION - √ TM MENU KEY RETURNS TO SETINGS MENU TITLE: ENABLES TOUCHSCREEN TEST TO EXIT, TAP AND HOLD OR PRESS ENTER BUTTON MENU MAP ENABLE / DISABLE SENSOR TEST PATTERN TOUCHSCREEN REDISCOVERS ALL HARDWARE REQUIRES REBOOT OF CAMERA Off OFF RECORD / STOP BEEP SPEAKER PROMPTS TO RESTORE TO FACTORY SETTINGS REQUIRES REBOOT OF CAMERA + REDISCOVER 75% 25 TO 100% ©2012 RED.COM, INC.
R E D D I G I T A L C I N E M A ® COPYRI GHT© 2012RedDi gi t alCi nema Al l t r ademar ks ,t r adenames ,l ogos ,i cons ,i mages ,wr i t t enmat er i al ,code,andpr oductnamesus edi nas s oci at i onwi t ht he a c c ompa n y i n gpr odu c t a r et h ec opy r i gh t s , t r a de ma r k sor ot h e r i n t e l l e c t u a l pr ope r t yown e da n dc on t r ol l e de x c l u s i v e l ybyRe dDi gi t a l Ci n e ma
