Instructions / Assembly

Figure 5
LATCH
OPTION B
Drill through 4 holes
using 5/32” drill
GASKET on
back of BASE
Figure 4
BASE
Back View
Push pins into
Receptacle Holes
1-3/8
(2) ROUND/SWITCH
ADAPTERS
Figure 3
Push pin(s) into
Receptacle Holes
(2) DUPLEX
ADAPTERS
Figure 2
(2) WASP
GUARDS
Fold here when
installing
Peel away
Backing
(4) Keyholes
Round Hole
See OPTION C
Cover
Cover
Hinge
Stainless Steel
Hinge Pin
Figure 1
VERTICAL MOUNTING ONLY!
Detail A
Detail B
Base
Port
Port
(Shown with
Wasp Guard installed)
Gasket
Adapter
(DUPLEX shown)
Wasp Guard
Screws
See OPTION B
Receptacle
Strap Face
Receptacle screws must
extend 5/8" from receptacle
strap face to mount cover
FS/FD
Wet Locations Box
(Not included)
2CKPL
Large Cover
2CKPM
Medium Cover
(shown)
1. TURN POWER OFF.
2. INSTALL WASP GUARDS. Remove protective backing from adhesive side of rubber WASP
GUARD. Position and place adhesive side on outside of curved rib in PORT opening.
Carefully fold WASP GUARD along top surface and secure to inside of curved rib in PORT.
Repeat for second WASP GUARD (Figure 1 & 2).
3. DETERMINE DESIRED ADAPTER. SWITCH, Use Round/Switch Adapter. ROUND
RECEPTACLE: Use Round 1-3/8" Adapter and remove inner circle. GFCI, no adaptor is
needed. DUPLEX: use Duplex Adapter (Figures 1 & 3).
4. INSTALL BASE TO BOX.
Use for Flush Mount and Wet Locations Box installations. Attach BASE using
receptacle screws.
NOTE: Position BASE with COVER HINGE on top and open PORTS on bottom. Attach
receptacle to box by loosely inserting the receptacle screws into the box. Thread screws
until heads extend 5/8” from receptacle strap faces (Figure 1, Detail A). Push adapter pin(s)
into receptacles or switches. (Figures. 3 & 4). Place BASE keyholes over receptacle/ or
/switch screws (Figure 1, Detail B). Make certain gasket overlaps box edges and tighten
screws to secure BASE.
5. INSTALL COVER. Place COVER onto BASE so that top HINGE holes are aligned. Push
HINGE PIN through COVER and BASE hinge holes so that the STAINLESS STEEL HINGE
PIN is fully seated and securely in place.
6. IRREGULAR SURFACES. Use caulk or sealant around BASE when installed on an irregular
at surface such as brick or wood siding to block water entry.
7. TURN ON POWER.
OPTION B: Alternative installation for Wet Locations (FS/FD) Boxes ONLY.
Verify receptacle is centered and securely fastened to box. Drill out (4) pre-marked holes in
BASE using 5/32” diameter drill (Figure 5). Push adapter pin(s) into receptacle or switch
(Figures 3 & 4). Make certain gasket overlaps box edges. Insert (4) furnished screws and
tighten to secure BASE. See steps 6 & 7.
OPTION C: Alternative GFCI installation (not pictured).
Verify GFCI receptacles are securely fastened to box. Insert (4) screws (furnished) through top
and bottom ROUND holes (Figure 1, Detail B) in BASE into threaded holes in GFCI. Make
certain gasket overlaps box edges and tighten screws to secure BASE. See steps 5,6 & 7.
Package Includes:
Cover Assembly with attached gasket, 2 Wasp Guards,
4 Adapters, Hinge Pin and 4 Screws.
Code Keeper
®
2-Gang
Wet Locations Cover, Extra Duty
Installation Instructions
For Vertical Mounting ONLY!
English
© 2013 Thomas & Betts Memphis, TN.
All Rights Reserved. www.tnb.com
TA04704 A Page 1 of 4
WARNING
ELECTRICAL HAZARD!
TURN POWER OFF!