MSDS

ManualsBrandsRed Head ManualsPaintS7 10 oz. Cartridge with Nozzle

Product Name: EPCON S7

Date prepared: January 25, 2012

Descriptions:

Part A: Vinyl Ester Adhesive

Part B: Peroxide Activator

Manufacturer: ITW Red Head · 2171 Executive Drive, Suite 100 · Addison, IL 60101

Emergency Number: 1-800-424-9300

Ingredients and Exposure Limits:

CAS

Number

TLV

(mg/m

)

PEL (mg/m

)

STEL

Part A: Vinyl Ester Resin

Proprietary

n/a

Vinyl Toluene

25013-15-4

n/a

480 mg/m

483 mg/m

Mixed acrylate esters

Proprietary

n/a

Part B: Dibutyl Phthalate

84742

5 mg/m

Benzoyl Peroxide

94360

5 mg/m

5 ppm

Ingredients CAS Number TLV: (mg/m3) PEL: (mg/m3) STEL

Abbreviations: TLV = ACGIH Threshold Limit Value PEL = OSHA Permissible Exposure

STEL = Short Term Exposure Limit

NA = Not Applicable NE = None Established

Physical Properties:

Part A: Beige Paste

Part B: Grey Paste

Specific Gravity

= 1.80 g/cm3 (at 20° C)

= 1.60 g/cm3 (at 20° C)

Boiling Point

= > 213°F

Water Solubility

None

SADT

n/a

137

F (55

roperties Part A: Beige Paste Part B: Gray Past

Safe Handling Procedures:

Handling Precautions: Keep away from children. Do not get in eyes, skin or on clothing. Wash

thoroughly after handling. Avoid breathing vapors. Use only as directed; avoid uncontrolled

mixing with other materials, esp. polymerizable or combustible materials.

Summary of content (4 pages)

PAGE 1
Product Name: EPCON S7 Date prepared: January 25, 2012 Descriptions: Part A: Vinyl Ester Adhesive Part B: Peroxide Activator Manufacturer: ITW Red Head · 2171 Executive Drive, Suite 100 · Addison, IL 60101 Emergency Number: 1-800-424-9300 Ingredients and Exposure Limits: CAS TLV PEL (mg/m3) STEL Number (mg/m3) Part A: Vinyl Ester Resin Proprietary n/a n/a n/a Vinyl Toluene 25013-15-4 n/a 480 mg/m3 483 mg/m3 Mixed acrylate esters Proprietary n/a n/a n/a Part B: Dibutyl Phthalate 84742 5 mg/m3 5 mg/m3 5 m
PAGE 2
Storage: For maximum shelf life, store in cool dry area between 40° to 80° F. Do not store above 110° F. Keep away from heat, sparks, open flame. Exposure to high heat can cause violent reaction. Do not store near combustibles. Spill Procedures: Collect with an absorbent material and place in a container for proper disposal. For large spills,transfer to salvage vessels, and dispose of according to state, local and Federal regulations. Flush area with water to remove residue.
PAGE 3
Other: Referral to a physician is recommended if there is any question about the seriousness of the exposure. TERIAL SAFETY 7DATA SHEET Stability and Reactivity: Stability: Stable at normal temperatures. Hazardous Polymerization:Will not occur at normal temperatures. Incompatibility: Strong acids and oxidizing agents. Decomposition Products: Thermal decomposition can yield COx, NOx, water and carbon. Conditions to Avoid: Avoid elevated temperatures which may shorten the shelf-life of this product.
PAGE 4
negligible (< 5%) Actual emissions are a function of substrate and process and should be considered on an individual basis. Canadian regulations: WHMIS hazard classes: B2, C, D2A, and D2B Canadian EPA: All ingredients are listed on the DSL or are exempt as impurities. The information and recommendations in this document are based on the best information available to us at the time of preparation.