Specification

ManualsBrandsRed Head ManualsTools & Hardware1/2 in. x 4 in. Hex-Nut-Head Sleeve Anchors (10-Pack)

Table Of Contents

Call our toll free number 800-848-5611 or visit our web site for the most

current product and technical information at www.itwredhead.com

DESCRIPTION/SUGGESTED SPECIFICATIONS

ADVANTAGES

1.Use a carbide tipped drill

bit whose diameter is equal

to the anchor. See Chart to

determine proper size bit for

anchor used. Dnll hole to any

depth exceeding minimum

embedment. Clean hole.

2. Insert assembled

anchor through fix-

ture and into hole so

that washer or head

is flush with materi-

als to be fastened.

INSTALLATION STEPS

3. Expand anchor

by tightening nut

or head 2 to 3

turns.

APPLICATIONS

Electrical junction boxes are common

applications for the Dynabolt Sleeve

anchor because it works well in solid

concrete, concrete block, and brick.

It is also available in several nished

head styles.

The Dynabolt Sleeve anchor works

well in hollow materials like brick and

block. It is available in zinc-plated

carbon steel and 304 stainless steel.

APPROVALS/LISTINGS

Meets or exceeds U.S. Government G.S.A. Specication A-A-1922A

(Formerly GSA: FF-S-325 Group II, Type 3, Class 3)

Factory Mutual

n Anchor diameter equals hole diameter

n Available in hex head and three other head styles

n Available 1/4 - 3/4” diameter up to 6-1/4” length

n Zinc plated carbon steel and 304 stainless steel

n Provides full 360° hole contact over large area

and reduces concrete stress

n Heavy-loading capacity

n Preassembled for faster, easier installations

n Dynabolt can be installed through object to

be fastened

n Sleeve design improves holding power

n No pre-spotting of holes necessary

Versatile,

Medium-Duty

Sleeve Anchor

Sleeve type anchors feature a split expansion sleeve over a threaded stud bolt body

and integral expander, nut and washer.

Anchors are made of Plated Carbon Steel, or Type 18-8 Stainless Steel.

Anchors should be installed with carbide tipped hammer drill bits made in

accordance to ANSI B212.15-1994.

Anchors are tested to ASTM E488 criteria.

Sleeve Type Anchors—

SPECIFIED FOR ANCHORAGE INTO CONCRETE, GROUT-FILLED CONCRETE BLOCK,

HOLLOW CONCRETE BLOCK AND BRICK

Dynabolt

Masonry

Sleeve

Anchor

Available Head Styles

Phillips Flat Head

(FS)

Hex Nut

(HN)

Full range of head style, corrosion protection, and sizes makes the

Dynabolt Sleeve the right product for almost any application.

Dynabolt

Hex Nut Sleeve Anchor

Dynabolt

Sleeve Anchors

Summary of content (3 pages)

PAGE 1
DESCRIPTION/SUGGESTED SPECIFICATIONS Sleeve Type Anchors— Dynabolt® SPECIFIED FOR ANCHORAGE INTO CONCRETE, GROUT-FILLED CONCRETE BLOCK, HOLLOW CONCRETE BLOCK AND BRICK Sleeve Anchors Versatile, Medium-Duty Sleeve Anchor Dynabolt Masonry Sleeve Anchor Sleeve type anchors feature a split expansion sleeve over a threaded stud bolt body and integral expander, nut and washer. Anchors are made of Plated Carbon Steel, or Type 18-8 Stainless Steel.
PAGE 2
SELECTION CHART Dynabolt Carbon Steel w/Zinc Plating HEAD STYLE PART NO. ANCHOR DIA. EFFECTIVE ANCHOR LENGTH* BOLT DIA. / & DRILL BIT THREADS PER SIZE in. (mm) INCH (mm) in. (mm) HN-1614 5/16" 1-1/2 (38.1) 1/4" / 20 1-1/4 (31.8) 1/4 (6.4) 100 / 4.0 1000 / 41 3/8" 1-7/8 (47.6) 5/16" / 18 1-1/2 (38.1) 3/8 (9.5) 50 / 3.5 500 / 36 3 (76.2) 5/16" / 18 1-1/2 (38.1) 1-1/2 (38.1) 50 / 4.9 400 / 40 1/2" 2-1/4 (57.2) 3/8" / 16 1-7/8 (47.6) 3/8 (9.5) 25 / 3.
PAGE 3
PERFORMANCE TABLE Dynabolt Ultimate Tension and Shear Values in Solid Concrete (lbs/kN)* Sleeve Anchors ANCHOR DIAMETER in. (mm) 1/4 5/16 3/8 1/2 5/8 3/4 INSTALLATION TORQUE ft. lbs. (Nm) (6.4) (7.9) (9.5) (12.7) (15.9) (19.1) 3.5 8 14 20 48 90 (4.7) (10.8) (19.0) (27.1) (65.1) (122.0) BOLT DIAMETER in. (mm) MINIMUM EMBEDMENT DEPTH in. (mm) 3/16 1/4 5/16 3/8 1/2 5/8 1-1/8 1-1/4 1-1/2 1-7/8 2 2-1/4 (4.8) (6.4) (7.9) (9.5) (12.7) (15.9) (28.6) (31.8) (38.1) (47.6) (50.8) (57.