User guide

ManualsBrandsRed Lion ManualsComputer AccessoriesCUB5I

 FOUR SELECTABLE D.C. RANGES

200 A, 2 mA, 20 mA, 200 mA

 MINIMUM AND MAXIMUM DISPLAY CAPTURE

 LCD, REFLECTIVE OR RED/GREEN LED BACKLIGHTING

 0.48" (12.2 mm) HIGH DIGITS

 OPTIONAL SETPOINT OUTPUT CARD

 OPTIONAL SERIAL COMMUNICATIONS CARD (RS232 or RS485)

 OPTIONAL USB PROGRAMMING CARD

 OPERATES FROM 9 TO 28 VDC POWER SOURCE

 FRONT PANEL OR CRIMSON PROGRAMMABLE

 DISPLAY COLOR CHANGE CAPABILITY AT SETPOINT OUTPUT

 NEMA 4X/IP65 SEALED FRONT BEZEL

MODEL CUB5I - MINIATURE ELECTRONIC 5-DIGIT DC CURRENT METER

GENERAL DESCRIPTION

The CUB5 provides the user the ultimate in flexibility, from its complete user

programming to the optional setpoint control and communication capability.

The CUB5I accepts a DC Current input signal and provides a display in the

desired unit of measure. The meter also features minimum and maximum

display capture, display offset, units indicator, and programmable user input.

The display can be toggled either manually or automatically between the

selected displays.

The CUB5 display has 0.48" (12.2 mm) high digits. The LCD is available in

two versions, reflective and red/green backlight. The backlight version is user

selectable for the desired color and also has variable display intensity.

The capability of the CUB5 can be easily expanded with the addition of

option cards. Setpoint capability is field installable with the addition of the

setpoint output cards. Serial communications capability for RS232 or RS485 is

added with a serial option card.

The CUB5 can be powered from an optional Red Lion Micro-Line/Sensor

Power Supply (MLPS), which attaches directly to the back of a CUB5. The

MLPS is powered from 85 to 250 VAC and provides up to 400 mA to drive the

unit and sensors.

CURRENT

The CUB5I is the DC Current meter. It features 4 current input ranges, that

are selected by the user via a programming jumper and software input range

selection. The ranges consist of following: 200 A, 2 mA, 20 mA, or 200 mA.

Users should select the appropriate current range that covers their maximum

signal input.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in this

literature or on equipment must be observed to ensure personal safety and to

prevent damage to either the instrument or equipment connected to it. If

equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

Do not use this meter to directly command motors, valves, or other actuators

not equipped with safeguards. To do so can be potentially harmful to persons or

equipment in the event of a fault to the meter.

Bulletin No. CUB5I-K

Drawing No. LP0658

Released 02/13

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

www.redlion.net

CAUTION: Risk of Danger.

Read complete instructions prior to

installationand operation of the unit.

CAUTION: Risk of electric shock.

DIMENSIONS In inches (mm)

.13 (3.3)

(43.4)

1.71

2.95 (74.9)

SEL

.15 (3.8)

1.54 (39.1)

RST

(68 )

+.025

-.000

-0

1.29 (32.8)

2.68

-.000

1.30

(33 )

-0

+.024

Note: Recommended minimum clearance (behind the panel) for mounting clip installation is 2.15" (54.6) H x 3.00" (76.2) W.

US LISTED

51EB

IND. CONT. EQ.

Summary of content (12 pages)

PAGE 1
Bulletin No. CUB5I-K Drawing No. LP0658 Released 02/13 Tel +1 (717) 767-6511 Fax +1 (717) 764-0839 www.redlion.net MODEL CUB5I - MINIATURE ELECTRONIC 5-DIGIT DC CURRENT METER  FOUR SELECTABLE D.C. RANGES 200 A, 2 mA, 20 mA, 200 mA  MINIMUM AND MAXIMUM DISPLAY CAPTURE  LCD, REFLECTIVE OR RED/GREEN LED BACKLIGHTING  0.48" (12.
PAGE 2
ORDERING INFORMATION TYPE MODEL NO.
PAGE 3
OPTIONAL PLUG-IN CARDS ADDING OPTION CARDS The CUB5 meters can be fitted with optional output cards and/or serial communications cards. The details for the plug-in cards can be reviewed in the specification section below. The plug-in cards, that are sold separately, can be installed initially or at a later date. VDS MAX: 30 VDC Offstate Leakage Current: 0.5 mA max. RS485 SERIAL COMMUNICATIONS CARD Type: RS485 multi-point balanced interface (non-isolated) Baud Rate: 300 to 38.
PAGE 4
3.0 INSTALLING PLUG-IN CARDS The Plug-in cards are separately purchased option cards that perform specific functions. The cards plug into the main circuit board of the meter CAUTION: The Plug-in cards and main circuit board contain static sensitive components. Before handling the cards, discharge static charges from your body by touching a grounded bare metal object. Ideally, handle the cards at a static controlled clean workstation. Also, only handle the cards by the edges.
PAGE 5
2 Wire With External Power Before connecting signal wires, the Input Range Jumper should be verified for proper position. INP + COMM _ CAUTION: Power input common is NOT isolated from user and input commons. In order to preserve the safety of the meter application, the power input common must be suitably isolated from hazardous live earth referenced voltage; or input common must be at protective earth ground potential.
PAGE 6
5.
PAGE 7
6.1 MODULE 1 - SIGNAL INPUT PARAMETERS (1-INP) PARAMETER MENU 1-INP Pro SEL rANGE dECPt OFSEt FILtr Display Offset Value Filter Setting Display Decimal Point Input Range bANd StYLE Filter Band Scaling Style INP 1 Input Value for Scaling Point 1 dSP 1 Display Value For Scaling Point 1   0.02A SELECTION 200uA 0.002A RANGE RESOLUTION SELECTION 200.00 A 0.02A 0.2A 2.
PAGE 8
USER INPUT FUNCTION DISPLAY MODE DESCRIPTION USrIN  Print  NO P-r5t Print and Reset Same as Print Request followed by a momentary reset of the assigned value(s). rSt-1 rSt-2 rSt12 Setpoint 1 Reset Resets setpoint 1 output. Setpoint 2 Reset Resets setpoint 2 output. Setpoint 1 and 2 Reset Reset both setpoint 1 and 2 outputs. DISPLAY NO P-Loc ZErO rESEt d-HLd d-SEL d-LEV COLOr MODE DESCRIPTION No Function Program Mode Lock-out User Input disabled.
PAGE 9
6.3 MODULE 3 - DISPLAY AND FRONT PANEL BUTTON PARAMETERS (3-dSP) PARAMETER MENU 3-dSP Pro Backlight Unit Only SEL dSP-t SEL rSt ZErO Display Update Time Front Panel Display Select Enable Front Panel Reset Enable Zero Display W/Display Reset ScroL UNItS COLOr Units Indicator Selection Display Scroll Enable d-LEV Display Intensity Level Display Color CodE Programming Security Code DISPLAY UPDATE TIME dSP-t   1 DISPLAY COLOR (BACKLIGHT UNIT ONLY) 1 0.
PAGE 10
6.4 MODULE 4 - SETPOINT OUTPUT PARAMETERS (4-SPt) PARAMETER MENU 4-SPt Backlight Unit Only SEL SPSEL Act-n Setpoint Select SPt-n Setpoint Action HYS-n Setpoint Value tON-n tOF-n On Time Delay Hysteresis Value The Setpoint Output Parameters are only active when an optional output module is installed in the meter. SPSEL   NO SP-1  NO YES Standby Operation ChC-n Change Display Color with Output State -19999 to 99999 Enter the desired setpoint value.
PAGE 11
button or user input manual reset, serial reset command or meter power cycle. When the user input or RST button is activated (momentary action), the corresponding “on” output is reset immediately and remains off until the trigger point is crossed again. (Previously latched alarms will be off if power up Display Value is lower than setpoint value.
PAGE 12
RST 5-SEr RST 4-SPt RST 3-dSP RST 2-SEC RST 1-INP RST NO Pro SEL SEL SEL SEL SEL SEL Baud Rate bAUd Setpoint Select SPSEL Display Update Time dSP-t Max Display Enable HI-En Input Range rANGE Exit Programming End Press and hold SEL button to enter Programming Mode.