Manual

ManualsBrandsRed Lion ManualsComputer AccessoriesCUB5T

 LCD, REFLECTIVE OR RED/GREEN LED BACKLIGHTING

 0.46" (11.7 mm) HIGH DIGITS

 7-DIGIT BI-DIRECTIONAL TIMING CAPABILITY

 6-DIGIT CYCLE COUNTING CAPABILITY

 OPTIONAL RELAY OUTPUT MODULE

 OPTIONAL SERIAL COMMUNICATIONS MODULE (RS232 or RS485)

 SELECTABLE TIMER RANGES AND OPERATING MODES

 ELAPSED TIMER AND PRESET TIMER FUNCTIONALITY

 DISPLAY COLOR CHANGE CAPABILITY AT PRESET OUTPUT

 OPERATES FROM 9 TO 28 VDC POWER SOURCE

 NEMA 4X/IP65 SEALED FRONT BEZEL

MODEL CUB5T - MINIATURE ELECTRONIC PRESET TIMER

AND CYCLE COUNTER

GENERAL DESCRIPTION

The CUB5T provides the ultimate in timer flexibility, from its complete user

programming to the optional relay output and serial communications capability.

The meter functions as an Elapsed Timer or Preset Timer. It also has a built-in

Cycle Counter. The display can be toggled either manually or automatically

between the Timer and Cycle Counter values. With eight different input

operating modes and 18 selectable timer ranges, the meter can be programmed

for a wide variety of timing applications.

The CUB5T has an LCD display with 0.46" (11.7 mm) high digits. The LCD

is available in two versions, reflective (CUB5TR00) and backlight (CUB5TB00).

The backlight version is user selectable for red or green backlighting with

variable display intensity.

The Timer has two signal inputs and eight input operating modes. These

modes provide level active or edge triggered start/stop operation. A Display

Hold mode will display the elapsed time for one cycle, while the next cycle

continues timing internally. The Timer Reset modes will automatically reset the

timer value when a time start edge is applied to the input. This allows sequential

timing cycles without having to manually reset the Timer.

In addition to the Timer inputs, a programmable User Input is available to

perform a variety of meter functions. All inputs are current sinking (active low)

and accept a variety of logic and open-collector output signal sources. Relay and

switch contacts can also be used as signal sources, when the software input

debounce filter is enabled.

The capability of the CUB5T can be easily expanded with the addition of a

field installable option module. When the CUB5RLY0 relay output module is

added, the meter becomes a Preset Timer. The Setpoint Output can be assigned

to the Timer or Cycle Counter values, and configured to suit a variety of control

and alarm requirements. Serial communications capability for RS232 or RS485

is added with a serial option module (CUB5COM).

The CUB5T can be powered from an optional Red Lion Micro-Line/Sensor

Power Supply (MLPS), which attaches directly to the back of a CUB5T. The

MLPS is powered from an 85 to 250 VAC source and provides up to 400 mA to

drive the meter and sensors.

SAFETY SUMMARY

All safety related regulations, local codes and instructions that appear in this

literature or on equipment must be observed to ensure personal safety and to

prevent damage to either the instrument or equipment connected to it. If

equipment is used in a manner not specified by the manufacturer, the protection

provided by the equipment may be impaired.

Do not use this meter to directly command motors, valves, or other actuators

not equipped with safeguards. To do so can be potentially harmful to persons or

equipment in the event of a fault to the meter.

Bulletin No. CUB5T-D

Drawing No. LP0628

Released 07/12

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

www.redlion.net

CAUTION: Risk of Danger.

Read complete instructions prior to

installation and operation of the unit.

CAUTION: Risk of electric shock.

DIMENSIONS In inches (mm)

.13 (3.3)

(43.4)

1.71

2.95 (74.9)

SEL

.15 (3.8)

1.54 (39.1)

RST

(68 )

+.025

-.000

-0

1.29 (32.8)

2.68

-.000

1.30

(33 )

1 2 34

-0

+.024

ON ECE

Note: Recommended minimum clearance (behind the panel) for mounting clip installation is 2.15" (54.6) H x 3.00" (76.2) W.

US LISTED

51EB

IND. CONT. EQ.

Summary of content (16 pages)

PAGE 1
Bulletin No. CUB5T-D Drawing No. LP0628 Released 07/12 Tel +1 (717) 767-6511 Fax +1 (717) 764-0839 www.redlion.net MODEL CUB5T - MINIATURE ELECTRONIC PRESET TIMER AND CYCLE COUNTER  LCD, REFLECTIVE OR RED/GREEN LED BACKLIGHTING  0.46" (11.
PAGE 2
ORDERING INFORMATION TYPE CUB5 Optional Plug-in Cards MODEL NO.
PAGE 3
OPTIONAL PLUG-IN CARDS ADDING OPTION CARDS WARNING: Disconnect all power to the meter before installing Plug-in card. The CUB5T meters can be fitted with optional relay card and/or serial communications cards. The details for the plug-in cards can be reviewed in the specification section below. The plug-in cards, that are sold separately, can be installed initially or at a later date.
PAGE 4
3.0 INSTALLING PLUG-IN CARDS The Plug-in cards are separately purchased option cards that perform specific functions. The cards plug into the main circuit board of the meter after the rear cover is removed WARNING: Disconnect all power to the meter before installing Plug-in Card. Comms Card ON 1 2 ECE 3 4 Relay Card REMOVING THE REAR COVER To remove the rear cover, locate the cover locking tab below the 2nd and 3rd input terminals.
PAGE 5
Sinking Logic PWR COMMON INP A INP B The user input of the meter is internally pulled up to +9 to +28 V with 10 K resistance. The input is active when it is pulled low. USR + Connect external switching device between the User Input terminal and Input Common. } INP COMM - INP COMM USR INP A +9 to +28 VDC: +VDC Power Common: -VDC INP B DC Power USR 4.2 USER INPUT WIRING INP COMM 4.1 POWER WIRING +9-28 VDC +9-28 VDC PWR COMMON 4.
PAGE 6
5.0 REVIEWING FRONT BUTTONS THE DISPLAY AND 1 SEL KEY RST DISPLAY MODE OPERATION ENTERING PROGRAM MODE PROGRAMMING MODE OPERATION SEL Select display (timer or cycle counter) Press and hold for 2 seconds to activate Store selected parameter and index to next parameter RST Reset value(s) per Front Panel Reset setting Advances through the program menu Increments selected parameter value or selection OPERATING MODE DISPLAY DESIGNATORS “t” - To the left of the display is the timer value.
PAGE 7
6.
PAGE 8
TIMER RESET AT POWER-UP RStsP-UP   YES NO USER INPUT FUNCTION (Cont’d) YES The Timer can be programmed to Reset at each meter power-up.   NO DISPLAY MODE NO Pro Loc d-SELECt rESEt d-HOLd HOLd-rSt DESCRIPTION Inhibit Inhibit Inhibit timing or counting for the selected value(s). d-LEVEL Display Intensity Level (Edge Triggered) Increase intensity one level for each activation.
PAGE 9
6.3 MODULE 3 - DISPLAY AND FRONT PANEL KEY PARAMETERS (3-dSPLAY) PARAMETER MENU 3-dSPLAY SEL Enb Front Panel Display Select RSt Enb d-ScroLL Front Panel Reset Enable Display Scroll Enable d-COLOr d-LEVEL Display Intensity Level Display Color   yES yES ProsCodE NO  The yES selection allows the SEL button to toggle between the timer and cycle counter displays.
PAGE 10
6.4 MODULE 4 - SETPOINT OUTPUT PARAMETERS (4-SEtPt) 4-SEtPt PARAMETER MENU SPt ASN SPt ACt Setpoint Assignment Setpoint Output Action SPt ON SPt OFF SPt tOUt Setpoint On Setpoint Off Setpoint Output Time-out StOP-t The Setpoint Output Parameters are only active when the optional relay module is installed in the meter. Some parameters will not appear depending on the Setpoint Assignment and Setpoint Output Action selected. t-VALUE SPt rSt SPtstOUt   00.01.00 00.00.
PAGE 11
6.5 MODULE 5 - SERIAL COMMUNICATIONS PARAMETERS (5-SEriAL) PARAMETER MENU 5-SEriAL Pro SEL PAritY bAUd dAtA Baud Rate Data Bit Parity Bit Addr Abbr Prnt OPt COPY Meter Address Abbreviated Printing Print Options Copy Program Settings Module 5 is the programming module for the Serial Communications Parameters. These parameters are used to match the serial settings of the CUB5T with those of the host computer or other serial device.
PAGE 12
Sending Serial Commands and Data Register Identification Chart When sending commands to the meter, a string containing at least one command character must be constructed. A command string consists of a command character, a value identifier, numerical data (if writing data to the meter) followed by a command terminator character, * or $.
PAGE 13
At the beginning of time interval t3, the meter responds with the first character of the reply. As with t1, the time duration of t3 is dependent on the number of characters and baud rate of the channel. At the end of t3, the meter is ready to receive the next command. Command Response Time The meter can only receive data or transmit data at any one time (half-duplex operation). During RS232 transmissions, the meter ignores commands while transmitting data, but instead uses RXD as a busy signal.
PAGE 14
This page intentionally left blank.
PAGE 15
NO 15 RST 5-SEriAL RST 4-SEtPt RST 3-dSPLAY RST 2-Count RST 1-INPUt RST Pro Cnt Enb Timer Range RANGE Exit Programming End SEL SEL SEL Baud Rate bAUd Setpoint Assignment SPt ASN Front Panel Display Select SEL Enb Cycle Counter Enable SEL SEL SEL Press and hold SEL key to enter Programming Mode.
PAGE 16
LIMITED WARRANTY The Company warrants the products it manufactures against defects in materials and workmanship for a period limited to two years from the date of shipment, provided the products have been stored, handled, installed, and used under proper conditions. The Company’s liability under this limited warranty shall extend only to the repair or replacement of a defective product, at The Company’s option.