RED DSMC POWER O P E R AT I O N G U I D E POWER MODULES | CHARGERS B AT T E R I E S | C A B L E S | A C C E S S O R I E S RED.
R E D D S M C P O W E R O P E R AT I O N G U I D E TABLE OF CONTENTS Disclaimer 3 Copyright Notice 3 Trademark Disclaimer 3 Compliance Statements 3 Safety Instructions 5 Battery Storage and Handling 6 Shipping Disclaimer 6 Chapter 1: DSMC Power Introduction 7 Read Before You Shoot 7 Power Operations 8 Basic Battery Operations 10 Additional Resources 10 Chapter 2: DSMC Power Components 11 DSMC Power Modules 12 RED Batteries 13 RED Chargers 14 Power Adaptors, Cables, and Accessories 15 Chapter
R E D D S M C P O W E R O P E R AT I O N G U I D E DISCLAIMER RED ® has made every effort to provide clear and accurate information in this operation guide, which is provided solely for the user’s information. While thought to be accurate, the information in this document is provided strictly “as is” and RED will not be held responsible for issues arising from typographical errors or user’s interpretation of the language used herein that is different from that intended by RED.
R E D D S M C P O W E R O P E R AT I O N G U I D E implies conformity to the following European Product Family Standards.
R E D D S M C P O W E R O P E R AT I O N G U I D E SAFETY INSTRUCTIONS DO NOT use near water. Avoid exposing to moisture. The unit is not waterproof, so contact with water could cause permanent damage to the unit as well as electric shock and serious injury to the user. DO NOT use in the rain or under other conditions with high moisture without appropriate protection, and immediately remove power source if exposed to moisture. Products marked with this symbol are class 2 devices.
R E D D S M C P O W E R O P E R AT I O N G U I D E BATTERY STORAGE AND HANDLING WARNING: Failure to read, understand, and follow these instructions may result in overheating, chemical leakage, smoke emission, fire, or other potentially harmful results. Always follow proper battery handling and storage practices. Improper handling and/or failure to abide by proper storage instructions may cause permanent damage to batteries, or degrade battery charge holding capacity.
R E D D S M C P O W E R O P E R AT I O N G U I D E 01 DSMC POWER INTRODUCTION REDVOLTs and REDVOLT Travel Charger The RED ® Digital Still and Motion Camera (DSMC ® ) system delivers high performance digital imaging over a wide range of frame rates and optical formats. The DSMC system is supported by an expansive arsenal of power modules, batteries, and chargers that provide adaptable configuration solutions to meet your needs.
R E D D S M C P O W E R O P E R AT I O N G U I D E POWER OPERATIONS This section describes the basic power operations of the DSMC system. For more information, see the DSMC Operation Guide, available at www.red.com/downloads. WARNING: Modules, displays, and accessories are NOT HOT SWAPPABLE, meaning that you cannot remove or install the item while the camera is turned on. Before installing or removing a module, display, or accessory, you MUST turn off the camera.
R E D D S M C P O W E R O P E R AT I O N G U I D E POWER CONSUMPTION The BRAIN draws approximately 60 W when recording in 5K resolution, at 24 FPS. Under typical conditions batteries provide the following operating time: REDVOLT: Powers the BRAIN and accessories for approximately 30 minutes. REDVOLT XL: Powers the BRAIN and accessories for approximately 90 minutes. RED BRICK: Powers the BRAIN and accessories for approximately 120 minutes.
R E D D S M C P O W E R O P E R AT I O N G U I D E BASIC BATTERY OPERATIONS This section describes the basic battery operations of REDVOLT, REDVOLT XL, and RED BRICK batteries. BATTERY DISCHARGE PROTECTION REDVOLT, REDVOLT XL, and RED BRICK batteries are equipped with discharge protection and shut off when output voltage falls below 10 V. Lithium-ion batteries self-discharge over time. Charging the battery restores lost capacity. For more information, go to “Battery Storage and Handling” on page 6.
R E D D S M C P O W E R O P E R AT I O N G U I D E 02 DSMC POWER COMPONENTS REDVOLT XL Power Pack This chapter provides an overview of the DSMC Power components, including: “DSMC Power Modules” on page 12 “RED Batteries” on page 13 “RED Chargers” on page 14 “Power Adaptors, Cables, and Accessories” on page 15 WARNING: Modules, displays, and accessories are NOT HOT SWAPPABLE, meaning that you cannot remove or install the item while the camera is turned on.
R E D D S M C P O W E R O P E R AT I O N G U I D E DSMC POWER MODULES This section describes DSMC power modules. REDVOLT XL Module RED DSMC modules enable you to configure your camera BRAIN for your exact shooting requirements and are designed to support REDVOLT ® , REDVOLT XL, and RED BRICK ® batteries. Most DSMC modules require an adaptor module to attach to the BRAIN. Specific module attachment requirements may vary. For more information, go to “DSMC Power Modules” on page 16.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED BATTERIES This section describes RED lithium-ion batteries. REDVOLT XL (left) and REDVOLT (right) The REDVOLT, REDVOLT XL, and RED BRICK are lightweight, rechargeable lithium-ion batteries designed to provide sustained power to the DSMC BRAIN. These batteries provide long-term mobile power and attach to the DSMC BRAIN via a DSMC power module or other RED accessory. For more information, go to “RED Batteries” on page 37.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED CHARGERS This section describes RED chargers used to recharge RED lithium-ion batteries. REDVOLT Travel Charger RED chargers are used to REDVOLT, REDVOLT XL, and RED BRICK lithium-ion batteries. For more information, go to “RED Chargers” on page 41. RED battery charger options include: ITEM PART NUMBER REDVOLT Travel Charger 790-0134 REDVOLT Charger (Quad) 740-0015 RED BRICK Charger 740-0006 WARNING: DO NOT overcharge batteries.
R E D D S M C P O W E R O P E R AT I O N G U I D E POWER ADAPTORS, CABLES, AND ACCESSORIES This section describes DSMC power adaptors, cables, and other accessories. AC Power Adaptor (DSMC) RED power adaptors, cables, and accessories are hand-made and expertly crafted to the highest standards. RED performance cables feature robust industry-standard LEMO connectors, and are available in a variety of connector sizes and lengths to support displays, modules, and other camera accessories.
R E D D S M C P O W E R O P E R AT I O N G U I D E 03 DSMC POWER MODULES DSMC ® power modules and adaptor modules provide battery power and other options for the DSMC BRAIN ® .
R E D D S M C P O W E R O P E R AT I O N G U I D E DSMC SIDE HANDLE DSMC Side Handle Front (left), DSMC Side Handle Rear (right) The DSMC Side Handle provides programmable menu controls and a battery compartment that supports one (1) REDVOLT battery. The backlit LCD displays camera parameter values and illuminates for operation in the dark. Insert a REDVOLT in the DSMC Side Handle to power the DSMC, modules, and attached accessories.
R E D D S M C P O W E R O P E R AT I O N G U I D E DSMC ADAPTOR MODULES This section describes the DSMC adaptor modules. MODULE ADAPTOR The Module Adaptor mounts to the back of the BRAIN and provides power and support for connected modules. The Module Adaptor includes 1/4-20 mounting holes for customized configuration support. Most DSMC modules require the use of an adaptor module. WARNING: The Module Adaptor is NOT compatible with the +1 Adaptor Module.
R E D D S M C P O W E R O P E R AT I O N G U I D E +1 ADAPTOR MODULE CONNECTIONS 1 2 3 4 5 +1 Adaptor Module # CONNECTOR CONNECTOR TYPE CONNECTOR FUNCTION 1 Mounting 1/4-20 mounting Supports bolt-on auxiliary equipment 2 EVF/LCD N/A Custom digital video and power interconnection between the BRAIN and RED EVF or LCD; Pinout not published 3 Auxiliary power out (PWR) 4-pin 0B LEMO Supplies unregulated (+) 11.
R E D D S M C P O W E R O P E R AT I O N G U I D E AUXILIARY POWER OUT (PWR) The auxiliary power output supplies unregulated +11.5 to +17 V battery pass-through power. The maximum sustained current draw is 2.0 A. 1 4 2 3 Auxiliary Power (PWR) Out 4-PIN 0B LEMO PWR CONNECTOR 1 PIN SIGNAL 1 Ground 2 Not used 3 Not used 4 +11.5 to 17 V unregulated battery pass-through power 1. Mating connector: ENG.0B.304.CLL COMPATIBLE CABLES 790-0334: 4-Pin to 2-Pin Adaptor Cable COPYRIGHT © 2014 RED.
R E D D S M C P O W E R O P E R AT I O N G U I D E DSMC ADAPTOR OPERATIONS This section describes the installation and removal of DSMC module adaptors. INSTALL THE +1 ADAPTOR MODULE REQUIRED TOOL: T20 Torx driver 1. Turn off the BRAIN. 2. Remove the REDMOTE, if attached. 3. Position the +1 Adaptor Module over the V-mount on the rear of the BRAIN. Install the +1 Module Adaptor 4. Insert the HDMI connector into the HDMI port on the BRAIN. Insert the HDMI Connector to the BRAIN COPYRIGHT © 2014 RED.
R E D D S M C P O W E R O P E R AT I O N G U I D E 5. Apply pressure and tighten the four (4) captive screws in a cross pattern (“X” pattern) approximately two (2) turns each using a T20 Torx driver. DO NOT FULLY TIGHTEN. Install screws 6. Fully tighten the four (4) screws in a cross pattern (“X” pattern). DO NOT OVERTIGHTEN. REMOVE THE +1 ADAPTOR MODULE REQUIRED TOOL: T20 Torx driver 1. Turn off the BRAIN. 2.
R E D D S M C P O W E R O P E R AT I O N G U I D E DSMC POWER MODULE OPERATIONS This section describes the attachment and removal of DSMC modules. These instructions are applicable to all DSMC modules, except adaptor modules. The Pro Battery Module (Quad) is shown. WARNING: DSMC modules attach to an adaptor module. DSMC modules DO NOT attach directly to the BRAIN. WARNING: Before installing or removing modules, you MUST turn off the BRAIN.
R E D D S M C P O W E R O P E R AT I O N G U I D E REMOVE A DSMC POWER MODULE REQUIRED TOOL: T20 Torx driver 1. Turn off the BRAIN. 2. Use a T20 Torx driver to rotate the lock on the adaptor module counterclockwise to the Unlock position. 3. Rotate the module upwards and away from the adaptor module to disengage. 4. Remove the module. COPYRIGHT © 2014 RED.
R E D D S M C P O W E R O P E R AT I O N G U I D E PRO BATTERY MODULE (DUAL) Pro Battery Module (Dual) The Pro Battery Module (Dual) provides power to the BRAIN using two (2) REDVOLT batteries. The Pro Battery Module (Dual) also supports hot swapping of REDVOLT batteries. Attaching outrigger handles and other tactical gear is convenient using the 1/4-20 mounting points on the top of the module. For installation and removal instructions, go to “DSMC Power Module Operations” on page 23.
R E D D S M C P O W E R O P E R AT I O N G U I D E PRO BATTERY MODULE (QUAD) Pro Battery Module (Quad) with REDVOLTs (left) and REDVOLT XL (right) The Pro Battery Module (Quad) harnesses the power of four (4) REDVOLT batteries or two (2) REDVOLT XL batteries. Similar to the Pro Battery Module (Dual), this module enables hot swap support for continuous power to the BRAIN without missing a shot. The module also offers 1/4-20 mounting points for configuration support..
R E D D S M C P O W E R O P E R AT I O N G U I D E REDVOLT XL MODULE REDVOLT XL Module The REDVOLT XL Module provides flexible mounting and power solutions for the BRAIN. The reversible switch plate on the REDVOLT XL Module enables you to mount the module to the BRAIN or another module. When the module is attached to the BRAIN, a connected REDVOLT XL battery powers the system.
R E D D S M C P O W E R O P E R AT I O N G U I D E REDVOLT XL MODULE CONNECTIONS 2 1 REDVOLT XL Module # CONNECTOR CONNECTOR TYPE CONNECTOR FUNCTION 1 AUX POWER OUT 3.8 A 2-pin 0B LEMO Provides 3.
R E D D S M C P O W E R O P E R AT I O N G U I D E CHARGE IN Use the 6-pin 1B LEMO CHARGE IN port to charge batteries and provide power to the AUX POWER OUT port. 2 3 1 4 6 5 CHARGE IN Connector 6-PIN 1B LEMO CHARGE IN CONNECTOR 1 PIN SIGNAL DESCRIPTION 1 +VBATT Power input, +11.5 to +17 V DC 2 +VBATT N/A 3 SCL-BATT Serial Battery Bus Clock 4 GROUND Power Return (Camera Ground) 5 GROUND N/A 6 SCA-BATT Serial Battery Bus Data 1. Mating connector: FGJ.1B.306.
R E D D S M C P O W E R O P E R AT I O N G U I D E CHARGE WITH THE REDVOLT XL MODULE REDVOLT XL Module Front (left), and Rear (right) The REDVOLT XL Module charges one (1) REDVOLT XL battery when an AC Power Adaptor (DSMC) is connected to the 6-pin 1B LEMO CHARGE IN connector. The REDVOLT XL Module can fully charge a discharged REDVOLT XL battery in approximately four (4) hours. The REDVOLT XL Module can charge a REDVOLT XL battery while attached to the camera, but only when the BRAIN is off.
R E D D S M C P O W E R O P E R AT I O N G U I D E INSTALL THE REDVOLT XL MODULE The REDVOLT XL Module is designed with a reversible switch plate, enabling direct installation to the DSMC BRAIN or mounting to other modules.
R E D D S M C P O W E R O P E R AT I O N G U I D E INSERT A REDVOLT XL 1. Align and insert the REDVOLT XL. 2. Apply pressure to the battery until a click is heard, signalling the battery is properly seated. Insert a REDVOLT XL Battery REMOVE A REDVOLT XL 1. Press the battery release buttons on both sides of the REDVOLT XL Module. 2. Remove the REDVOLT XL. Remove a REDVOLT XL Battery COPYRIGHT © 2014 RED.
R E D D S M C P O W E R O P E R AT I O N G U I D E QUICKPLATE MODULE Quickplate Module The Quickplate Module attaches to a +1 Adaptor Module or Module Adaptor to provide RED BRICK power support for the DSMC BRAIN. Unlike the Backpack Quickplate, the Quickplate Module does not require a LEMO connector cable or Backpack Baseplate. Use a battery-equipped DSMC Side Handle or an AC Power Adaptor (DSMC) to keep the camera running while hot swapping batteries.
R E D D S M C P O W E R O P E R AT I O N G U I D E ATTACH THE QUICKPLATE MODULE Quickplate Module attached to BRAIN The Quickplate Module attaches to a Module Adaptor or +1 Adaptor Module in the same way that other DSMC modules attach. For more information, go to “DSMC Power Module Operations” on page 23. BACKPACK QUICKPLATE (SHORT) Backpack Quickplate (Short) and Backpack Base Plate The Backpack Quickplate and Backpack Quickplate (Short) attach to the Backpack Base Plate to support a RED BRICK.
R E D D S M C P O W E R O P E R AT I O N G U I D E BACKPACK QUICKPLATE CONNECTORS The Backpack Quickplate offers one (1) D-Tap connector that provides power (70 W max) for camera accessories. 1 2 Backpack Quickplate D-Tap Connector 2-PIN DTAP CONNECTOR PIN SIGNAL 1 Ground 2 +12 VDC BACKPACK QUICKPLATE (SHORT) CONNECTORS The Backpack Quickplate (Short) offers two (2) 0B 2-pin AUX ports that provide a maximum combined output of 3.8 A.
R E D D S M C P O W E R O P E R AT I O N G U I D E INSTALL BACKPACK BASE PLATE AND BACKPACK QUICKPLATE (SHORT) REQUIRED TOOL: 3.0 mm Hex driver 1. Turn off the BRAIN. 2. Place the Backpack Base Plate on the rear of the BRAIN. 3. Insert four (4) M4x0.7 mm x 8 mm mounting screws into the Backpack Base Plate mounting holes. 4. Use a 3.0 mm Hex driver to tighten screws in a cross pattern (“X” pattern) approximately two (2) turns each. DO NOT FULLY TIGHTEN. 5.
R E D D S M C P O W E R O P E R AT I O N G U I D E 04 RED BATTERIES REDVOLT ® , REDVOLT XL, and RED BRICK ® batteries are rechargeable lithium-ion batteries designed to power the DSMC ® BRAIN ® during active shooting sessions when you can’t be tied down by cables.
R E D D S M C P O W E R O P E R AT I O N G U I D E REDVOLT AND REDVOLT XL REDVOLT XL (left) and REDVOLT (right) REDVOLT and REDVOLT XL batteries are lightweight and rechargeable batteries designed to power the DSMC BRAIN. REDVOLT batteries can be mounted to DSMC power modules for extended mobile power, or inserted into the DSMC Side Handle for short term power.
R E D D S M C P O W E R O P E R AT I O N G U I D E REDVOLT LED ARRAY REDVOLT LED Array `v The REDVOLT and REDVOLT XL battery LED arrays consist of three (3) LEDs and a status button. Press the status button to illuminate the LEDs, displaying the remaining battery charge level in 33.3% steps. If a single LED blinks or no LEDs illuminate, then the battery is discharged and requires charging.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED BRICK PERFORMANCE The following table provides operational data on RED BRICK battery usage and charging times. BATTERY NOMINAL ENERGY RUN TIME 1 CHARGE TIME (80%) CHARGE TIME (FULL) RED BRICK 153 Wh 120 min 95 min 190 min 1 Approximate battery run times based on recording in 4K FF resolution at 24 FPS. RED BRICK LED ARRAY RED BRICK LED Array (Approximately 60%) The RED BRICK battery LED array consists of five (5) LEDs and a status button.
R E D D S M C P O W E R O P E R AT I O N G U I D E 05 RED CHARGERS REDVOLT ® and RED BRICK ® chargers are designed to recharge RED ® lithium-ion batteries. For more information on battery compatibility and operation, go to “Battery Storage and Handling” on page 6.
R E D D S M C P O W E R O P E R AT I O N G U I D E REDVOLT TRAVEL CHARGER REDVOLT Travel Charger ` The REDVOLT Travel Charger is a compact and portable charger designed to charge a single REDVOLT lithiumion battery. The charger times out automatically after 105 minutes if the battery does not reach a full charge. NOTE: The REDVOLT Travel Charger stops charging automatically if battery temperature exceeds 40˚C (104˚F), or drops below 0°C (32°F).
R E D D S M C P O W E R O P E R AT I O N G U I D E REDVOLT CHARGER (QUAD) REDVOLT Charger (Quad) The REDVOLT Charger (Quad) is the fastest way to charge up to four REDVOLT or two REDVOLT XL batteries. All batteries charge simultaneously, with up to 1.75 A distributed evenly to each cell until fully charged. The REDVOLT Charger (Quad) can charge multiple REDVOLT or REDVOLT XL batteries in two (2) hours or less.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED BRICK CHARGER RED BRICK Charger The RED BRICK Charger offers rechargeable support for RED BRICK (153 Wh) lithium-ion batteries. The RED BRICK Charger provides up to 4 A in constant current mode. The RED BRICK Charger charges two (2) attached RED BRICK batteries sequentially in approximately six (6) to eight (8) hours. The RED BRICK Charger can charge one (1) fully discharged RED BRICK in approximately three (3) hours.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED BRICK CHARGER CONNECTIONS AND FEATURES 1 2 6 3 7 4 8 9 5 10 11 RED BRICK Charger # CONNECTOR/FEATURE DESCRIPTION 1 Carrying handle Robust carrying handle 2 Battery charging LEDs Indicates battery charge state 3 Auxiliary port LED Indicates auxiliary connection state 4 LEMO auxiliary port 13.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED BRICK CHARGER LED INDICATORS COLOR PATTERN DESCRIPTION Green Charger on, battery fully charged Red/Green flashing (alternating) Charger on, fail condition Red Charger on, no battery connected Amber flashing Charger on, battery connected and charging RECHARGE RED BRICKS 1. Connect the RED BRICK Charger to a 100–240 VAC, 50/60 Hz power outlet. 2. Turn on the RED BRICK Charger using the power switch. 3.
R E D D S M C P O W E R O P E R AT I O N G U I D E 06 POWER ADAPTORS, CABLES, AND ACCESSORIES RED ® offers a wide variety of performance power adaptors, cables, and accessories to power and provide support for the DSMC ® , power modules, and other DSMC components.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED CRADLE RED Cradle The RED Cradle enables you to simultaneously mount a RED BRICK and RED DRIVE or RED RAM. NOTE: Requires a 2B-to-1B Power Adaptor Cable for use with the BRAIN. RED QUICKPLATE RED Quickplate The RED Quickplate provides a reliable solution for powering the BRAIN with a RED BRICK. NOTE: Requires a 2B-to-1B Power Adaptor Cable for use with the BRAIN. COPYRIGHT © 2014 RED.
R E D D S M C P O W E R O P E R AT I O N G U I D E BATTERY BELT CLIP (DSMC) Battery Belt Clip (DSMC) The Battery Belt Clip (DSMC) provides a portable power solution for lightweight hand-held configurations. The attached power cable with a 6-pin 1B LEMO connector allows you to plug directly into the BRAIN DC IN port, without the use of a 2B-to-1B Power Adaptor Cable. COPYRIGHT © 2014 RED.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED CABLES RED cables and accessories provide solutions for video monitoring, audio, and power supply requirements. EVF/LCD CABLES EVF/LCD Cable (18") EVF/LCD Cables are high quality braided cables with industry-standard LEMO connectors. They provide a clean video feed and power source from the EVF/LCD port on the BRAIN to an EVF or LCD display. These cables are available in straight or right angle connector options.
R E D D S M C P O W E R O P E R AT I O N G U I D E 4-PIN TO 2-PIN ADAPTOR CABLE 4-Pin to 2-Pin Adaptor Cable The 4-Pin to 2-Pin Adaptor Cable enables you to power 2-pin based accessories from the +1 Adaptor Module or Pro I/O Module. 2-PIN 1B LEMO-TO-FLYING LEAD CABLE The 2-Pin 1B LEMO-to-Flying Lead Cable provides a 1B LEMO connector and flying leads for custom cable creation. Create a custom cable for powering camera accessories using 1B 12 V ports available on DSMC modules.
R E D D S M C P O W E R O P E R AT I O N G U I D E 07 TROUBLESHOOT DSMC POWER RED BATTERIES AND CHARGERS This section provides general troubleshooting information for DSMC ® power-related products. For more information, see the RED Support page, available at https://support.red.com/home . BATTERY DOES NOT FULLY CHARGE In some cases, batteries may not fully charge. If you performed a typical full charge with a RED charger and the battery does not fully charge, follow the instructions below: 1.
R E D D S M C P O W E R O P E R AT I O N G U I D E A TECHNICAL SPECIFICATIONS DSMC MODULES This section provides the technical specifications for DSMC modules. DSMC SIDE HANDLE SPECIFICATION DESCRIPTION Dimensions Height: 4.96 in. (126 mm) Width: 2.76 in. (70 mm) Depth: 3.31 in. (84 mm) Weight Approximately 1.
R E D D S M C P O W E R O P E R AT I O N G U I D E +1 ADAPTOR MODULE SPECIFICATION DESCRIPTION Dimensions Height: 4.29 in. (109 mm) Width: 3.54 in. (90 mm) Depth: 0.87 in. (22 mm) Weight Approximately 0.75 lbs (349 g) Construction Aluminum Alloy Operating Temperature 0°C to 40°C (32 to 104°F) Storage Temperature –30°C to 70°C (–22°F to 158°F) Connectors RED EVF/LCD PWR (4-pin 0B LEMO), 2.0 Amp continuous load at 11.5-17 VDC Firmware Requirement DSMC firmware v4.0.
R E D D S M C P O W E R O P E R AT I O N G U I D E REDVOLT XL MODULE SPECIFICATION DESCRIPTION Dimensions Height: 4.29 in. (109 mm) Width: 4.41 in. (112 mm) Depth: 1.52 in. (39 mm) Weight Approximately 0.94 lbs (425 g), Module only Construction Aluminum Alloy Operating Temperature 0°C to 40°C (32°F to 104°F) Storage Temperature –30°C to 70°C (–22°F to 158°F) Connectors CHARGE IN (6-pin 1B LEMO) AUX POWER OUT (2-pin 0B LEMO) Firmware Requirement DSMC firmware v5.1.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED BATTERIES This section describres the technical specifications for RED batteries. REDVOLT SPECIFICATION DESCRIPTION Dimensions Height: 3.21 in. (82 mm) Width: 1.67 in. (43 mm) Depth: 1.68 in. (43 mm) Weight Approximately 0.55 lbs (249 g) Battery Type Rechargeable Lithium-ion Battery Battery Capacity 37 Wh / 250 mAh Nominal Voltage 14.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED BRICK SPECIFICATION DESCRIPTION Dimensions Height: 6.46 in. (166 mm) Width: 3.54 in. (90 mm) Depth: 2.05 in. (52 mm) Weight Approximately 2.29 lbs (1,038 g) Battery Type Rechargeable Lithium-ion Battery Battery Capacity 153 Wh / 10.4 Ah Output Voltage 14.
R E D D S M C P O W E R O P E R AT I O N G U I D E RED CHARGERS This section describes the technical specifications for RED chargers. REDVOLT TRAVEL CHARGER SPECIFICATION DESCRIPTION Dimensions Height: 4.29 in. (109 mm) Width: 4.41 in. (112 mm) Depth: 1.52 in. (39 mm) Weight Approximately 0.48 lbs (218 g), Charger only Power Supply 100-240 V, .8 A , 50-60 Hz Power Output 16.8 V, 1.
R E D D S M C P O W E R O P E R AT I O N G U I D E B DSMC MODULE COMPATIBILITY This chapter provides information on module types, mounting priority, module restrictions, and compatibility. DSMC MODULE TYPES AND PRIORITY Attach modules to the BRAIN in the order outlined below to optimize power distribution, cable position, and access to batteries, media, and controls. DSMC Module Priority Attach modules to the back of the BRAIN in the following order: 1.
R E D D S M C P O W E R O P E R AT I O N G U I D E PRO I/O MODULE Module Adaptor and Pro I/O Module When using a Pro I/O Module along with other DSMC modules, ensure that it is attached closest to the BRAIN, behind the Module Adaptor or +1 Adaptor Module. This improves access to cables, modules, and batteries, as well as ensuring proper power distribution. WARNING: DO NOT use the EVF/LCD port on the +1 Adaptor Module if a Pro I/O Module is connected to the DSMC BRAIN.
R E D D S M C P O W E R O P E R AT I O N G U I D E DSMC MODULE COMPATIBILITY MATRIX DSMC MODULES MODULE ADAPTOR MODULE ADAPTOR +1 ADAPTOR PRO MODULE BATTERY MODULE (DUAL) PRO BACKPACK QUICKPLATE REDVOLT PRO I/O REDMOTE BATTERY QUICKPLATE MODULE XL MODULE MODULE MODULE (SHORT) (QUAD) N/A X √ √ √ √ √ √ √ +1 ADAPTOR MODULE X N/A √ √ √ √ √ √1 √ PRO BATTERY MODULE (DUAL) √ √ N/A X √ √ X √ √ PRO BATTERY MODULE (QUAD) √ √ X N/A √ √ X √ √ BACKPACK QUICKPLATE √ √ √ √
RED DIGITAL CINEMA COPYRIGHT© 2014 RED.COM, INC. All trademarks, trade names, logos, icons, images, written material, code, and product names used in association with the accompanying product are the copyrights, trademarks, or other intellectual property owned and controlled exclusively by RED.COM, INC.
