RED DSMC O P E R AT I O N G U I D E EPIC | SCARLET | V5.2 DRAGON | MYSTERIUM-X RED.
R E D D S M C O P E R AT I O N G U I D E TABLE OF CONTENTS Disclaimer 3 Copyright Notice 3 Trademark Disclaimer 3 Compliance Statements 4 Safety Instructions 6 Battery Storage and Handling 7 Shipping Disclaimer 7 Chapter 1: DSMC System Introduction 8 Read Before You Shoot 8 DSMC BRAIN 9 RED Digital Sensors 10 R3D File Format and REDCODE 11 Shoot For Video and Stills 12 Post-Production with REDCINE-X PRO 12 HDRx and MAGIC MOTION 13 Additional Resources 13 Chapter 2: DSMC System Components 14
R E D D S M C O P E R AT I O N G U I D E GIG-E (Ethernet) 179 DC IN (Power Input) 180 MIC-1, MIC-2 (Microphone Audio) 181 SSD Module Connectors 181 Appendix C: Lens Mounts and Lenses 182 Lens Mounts 182 Lenses 185 Appendix D: Default Key Functions 191 Appendix E: Menu Map 195 DISCLAIMER RED has made every effort to provide clear and accurate information in these installation instructions, which are provided solely for the user’s information.
R E D D S M C O P E R AT I O N G U I D E COMPLIANCE STATEMENTS CAUTION: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because there signals could interfere with critical aircraft instruments. INDUSTRIAL CANADA EMISSION COMPLIANCE STATEMENTS This device complies with Industry Canada license-exempt RSS standards RSS 139 and RSS 210.
R E D D S M C O P E R AT I O N G U I D E INFORMATION NORWAY Products with the CE marking comply with the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Product Family Standards.
R E D D S M C O P E R AT I O N G U I D E SAFETY INSTRUCTIONS DO NOT use the camera or accessories near water. Avoid exposing your camera to moisture. The unit is not waterproof, so contact with water could cause permanent damage to the unit as well as electric shock and serious injury to the user. DO NOT use the camera in the rain or under other conditions with high moisture without appropriate protection, and immediately remove power source if camera or accessories are exposed to moisture.
R E D D S M C O P E R AT I O N G U I D E BATTERY STORAGE AND HANDLING permanent damage to the battery. DO NOT connect the positive (+) and negative (-) terminals to a metal object such as a wire. DO NOT transport or store the battery together with metal objects such as jewelry, hairpins, etc. as they may generate heat if they come into contact with the battery. DO NOT discard the battery into fire or heat.
R E D D S M C O P E R AT I O N G U I D E 01 DSMC SYSTEM INTRODUCTION EPIC Digital Still and Motion Cameras (DSMC) The RED ® Digital Still and Motion Camera (DSMC ® ) system delivers high performance digital imaging over a wide range of frame rates and optical formats including Super 35mm/APS-H. This section introduces the imaging capabilities and advanced features of the DSMC system.
R E D D S M C O P E R AT I O N G U I D E DSMC BRAIN EPIC-M BRAIN (Left) and SCARLET-X BRAIN (Right) The RED Digital Still and Motion Camera (DSMC) system is a model for image innovation, ushering digital cinema and photography technology into the next generation. At the center of RED modular system is the DSMC BRAIN, housing the critical image capture electronics and digital image sensor.
R E D D S M C O P E R AT I O N G U I D E RED DIGITAL SENSORS Each EPIC or SCARLET BRAIN is equipped with one of the following sensors: RED DRAGON (6K) MYSTERIUM-X ® (5K) MONOCHROME (5K) RED DRAGON MONOCHROME (6K) RED DRAGON SENSOR RED DRAGON 6K Resolution The RED DRAGON sensor captures over nine (9) times more resolution than standard HD. The result is unrivaled detail and impressive native exposure that exceeds 35mm film in both latitude and image density.
R E D D S M C O P E R AT I O N G U I D E The MYSTERIUM-X sensor includes high-precision analog to digital conversion, capable of delivering up to 13.5 stops of dynamic range with daytime light sources 800 ISO. With HDRx, dynamic range can be extended up to approximately 18 stops. A native color balance of 5,000K (Kelvin) and electronic white balance compensation from 1,700K to 10,000K delivers natural images in any environment.
R E D D S M C O P E R AT I O N G U I D E SHOOT FOR VIDEO AND STILLS High resolution video, such as the digital footage captured by the RED DSMC, has surpassed the detail necessary to produce professional full-sized prints. Because of the ability to record at high frame rates and resolution, the DSMC is ideally suited to capture video and still images, simultaneously. Using REDCINE-X PRO, or other editing applications supporting the RED SDK, you can pull full resolution still images from R3D files.
R E D D S M C O P E R AT I O N G U I D E HDRX AND MAGIC MOTION HDRx HDRX HDRx extends dynamic range up to six (6) stops by simultaneously capturing two (2) images of identical resolution and frame rate. The first image is a normally exposed track (A-track), while the second is an underexposed track (X-track) with an exposure value that reflects the additional stops of highlight protection. These tracks are “motion-conjoined” during recording, leaving no time gap between the two (2) exposures.
R E D D S M C O P E R AT I O N G U I D E 02 DSMC SYSTEM COMPONENTS EPIC-M RED DRAGON Kit This section provides an overview of the RED DSMC system components, including: “BRAIN” on page 15 “DSMC Media Modules” on page 16 “REDMAG and RED MINI-MAG Systems” on page 18 “DSMC Adaptor Modules” on page 19 “DSMC Power Modules” on page 21 “RED Batteries and Chargers” on page 22 “Other DSMC Modules” on page 23 “Displays and Electronic Viewfinders” on page 25 “DSMC Remotes and Con
R E D D S M C O P E R AT I O N G U I D E BRAIN EPIC BRAIN (Side) The BRAIN is the image processing center of the DSMC system and supports power, media, and other modules. BRAIN CONTROL: PWR/REC BUTTON Fully press and hold the PWR/REC button for two (2) seconds to turn on/off. When the DSMC is on, fully press and then release the PWR/REC button to toggle record start/stop. BRAIN LEDS This section describes the LED functions for all BRAINs.
R E D D S M C O P E R AT I O N G U I D E DSMC MEDIA MODULES This section describes the DSMC media modules. RED offers the following DSMC media modules: ITEM PART NUMBER DSMC 1.8" SSD Side Module 720-0013 DSMC 1.8" SSD Side Module (DRAGON) 1 N/A Carbon Fiber DSMC 1.8" SSD Side Module (DRAGON) N/A 2 RED MINI-MAG Side SSD Module 720-0021 Carbon Fiber RED MINI-MAG Side SSD Module 2 N/A Rear SSD Module 720-0009 1. The DSMC 1.
R E D D S M C O P E R AT I O N G U I D E DSMC SIDE SSD MODULE CONTROLS CONTROL DESCRIPTION User Key 1 Programmable key User Key 1 + 2 Press: Eject Media User Key 2 Programmable key User Key 1 + 2 Press: Eject Media REC button Programmable key Full Press: Record Toggle Half Press: AF Start REAR SSD MODULE Rear SSD Module The Rear SSD Module secures to the back of a Module Adaptor or a +1 Adaptor Module to serve as a rear location for recording to a REDMAG 1.8" SSD.
R E D D S M C O P E R AT I O N G U I D E REDMAG AND RED MINI-MAG SYSTEMS This section describes the REDMAG and RED MINI-MAG systems. RED MINI-MAG (512GB) REDMAG 1.8" SSDs and RED MINI-MAG SSDs deliver fast and reliable recording options for your DSMC. RED STATIONs enable you to connect media to your computer for offloading and editing. RED offers the following REDMAG 1.
R E D D S M C O P E R AT I O N G U I D E DSMC ADAPTOR MODULES This section describes the DSMC adaptor modules. Module Adaptor (left) and +1 Adaptor Module (right) DSMC adaptor modules enable you to connect other DSMC modules to the BRAIN for expandable functionality. The +1 Adaptor Module provides an auxiliary power port for accessories and an additional EVF/LCD port for additional monitor viewing and output.
R E D D S M C O P E R AT I O N G U I D E +1 ADAPTOR MODULE CONNECTIONS 1 2 3 4 5 +1 Adaptor Module CONNECTOR CONNECTOR TYPE CONNECTOR FUNCTION Mounting 1/4-20 mounting Supports bolt-on auxiliary equipment EVF/LCD 1 N/A Custom digital video and power interconnection between BRAIN and RED EVF or RED LCD; Pinout not published Auxiliary power out (PWR) 4-pin 0B LEMO Supplies unregulated (+) 11.
R E D D S M C O P E R AT I O N G U I D E DSMC POWER MODULES This section describes the DSMC power modules. Pro Battery Module (Quad) DSMC power modules attach to a Module Adaptor or +1 Adaptor Module to provide the DSMC with flexible power options for REDVOLT, REDVOLT XL, and RED BRICK batteries. When used in combination with a DSMC AC Power Adaptor or DSMC Side Handle, you can hot-swap batteries without interrupting recording.
R E D D S M C O P E R AT I O N G U I D E RED BATTERIES AND CHARGERS This section describes the RED lithium-ion batteries and charger solutions. REDVOLT XL (left) and REDVOLT (right) The REDVOLT, REDVOLT XL, and RED BRICK are lightweight, rechargeable lithium-ion battery cells that provide sustained power to the BRAIN. These batteries provide long-term mobile power and attach to the BRAIN via a DSMC power module or other RED accessory, such as the DSMC Side Handle.
R E D D S M C O P E R AT I O N G U I D E OTHER DSMC MODULES This section describes other DSMC modules. RED offers the following miscellaneous DSMC modules: ITEM PART NUMBER Pro I/O Module 720-0004 RED 4K Broadcast Module 1 720-0025 1. The 4K Broadcast Module requires that your DSMC is on firmware v5.2.8 or later.
R E D D S M C O P E R AT I O N G U I D E RED 4K BROADCAST MODULE RED 4K Broadcast Module The RED 4K Broadcast Module allows for live 4K streaming, enabling you to capture and view action in realtime. Compatible with both EPIC DRAGON and SCARLET DRAGON cameras, the 4K Broadcast Module uses four (4) 3G-SDI output connections to broadcast 4K video at up to 60 frames per second. Five (5) 1/4-20 mounting holes are built into the top of the module, allowing for various mechanical peripherals to be attached.
R E D D S M C O P E R AT I O N G U I D E DISPLAYS AND ELECTRONIC VIEWFINDERS This section describes the RED displays and electronic viewfinders (EVFs). RED offers the following displays and EVFs: ITEM PART NUMBER RED Touch 5.0" LCD (800 x 400 resolution) 730-0008 RED Touch 7.0" LCD 1 (1920 x 1136 resolution) 730-0007 RED Touch 9.0" LCD (1280 x 784 resolution) 730-0011 RED PRO LCD 7" (1024 x 600 resolution) 730-0009 BOMB EVF (LCOS) 730-0004 BOMB EVF (OLED) 730-0010 1. The RED Touch 7.
R E D D S M C O P E R AT I O N G U I D E BOMB EVF (LCOS) AND BOMB EVF (OLED) The BOMB EVF (LCOS) and BOMB EVF (OLED) deliver specialized viewing solutions for the DSMC. BOMB EVF (OLED) The BOMB EVF (LCOS) is a high-definition, lightweight, and low-profile viewfinder. The BOMB EVF (OLED) uses OLED technology, providing deeper blacks and more color accurate images. ITEM RESOLUTION CONTRAST RATIO DIOPTER RANGE BOMB EVF (LCOS) 1280 (wide) x 784 (high); full color 1000:1 typical 2.0 to –5.0.
R E D D S M C O P E R AT I O N G U I D E DSMC SIDE HANDLE DSMC Side Handle Front (left), DSMC Side Handle Rear (right) The DSMC Side Handle provides user programmable menu controls and a battery compartment that holds one (1) REDVOLT battery. The DSMC Side Handle LCD display shows camera parameter values and illuminates for operation in dark environments.
R E D D S M C O P E R AT I O N G U I D E REDMOTE REDMOTE The REDMOTE is a remote camera control unit for the DSMC that attaches to the rear of the BRAIN or rearmost expansion module. The REDMOTE may be detached from the camera or rearmost module and provide wireless remote control of the camera over the proprietary REDLINK™ protocol. For a full list of REDMOTE user keys and default actions, go to “Default Key Functions” on page 191. For more information, go to “REDMOTE Operation” on page 133.
R E D D S M C O P E R AT I O N G U I D E DSMC LENS MOUNTS This section describes the DSMC lens mounts. DSMC Ti PL Mount RED offers the following DSMC lens mounts: ITEM PART NUMBER DSMC Ti PL Mount 725-0003 DSMC Al Canon Mount 725-0004 DSMC Ti Canon Mount 725-0005 DSMC Al Nikon Mount 725-0006 DSMC Ti Nikon Mount 725-0007 DSMC Al Leica-M Mount 725-0008 DSMC Motion Mount Ti PL 1 DSMC Motion Mount Ti Canon 725-0012 1 725-0014 1.
R E D D S M C O P E R AT I O N G U I D E DSMC INTERCHANGEABLE OLPFS This section describes the DSMC Interchangeable OLPF system and modular OLPFs. DSMC Interchangeable OLPF System The DSMC Interchangeable OLPF system is an upgrade to the optical low-pass filter (OLPF) in your EPIC DRAGON or SCARLET DRAGON. The modular mounting system enables you to remove and replace OLPFs to achieve optimal color reproduction in any lighting and environment.
R E D D S M C O P E R AT I O N G U I D E 03 DSMC BASIC OPERATIONS POWER OPERATIONS This section describes the basic power operations of the DSMC system. For more information, see the DSMC Power Operation Guide available at www.red.com/downloads. WARNING: Modules, displays, and accessories are NOT HOT SWAPPABLE, meaning that you cannot remove or install the item while the camera is turned on. Before installing or removing a module, display, or accessory, you MUST turn off the camera.
R E D D S M C O P E R AT I O N G U I D E POWER PRIORITY When multiple power sources are connected to the BRAIN, power consumption is prioritized in this sequence: 1. DC power supply (DC IN connector) 2. Attached RED BRICK ® (Lowest state of charge first) 3. Battery module batteries (SEARAY connector; lowest state of charge first) 4. REDVOLT battery in an attached DSMC Side Handle POWER CONSUMPTION The BRAIN draws approximately 60 W when recording in 5K resolution, at 24 FPS.
R E D D S M C O P E R AT I O N G U I D E CONFIGURE YOUR DSMC This section describes common options for configuring your DSMC system. INSTALL THE DSMC SIDE HANDLE WARNING: Before installing or removing the DSMC Side Handle, you MUST turn off the BRAIN. REQUIRED TOOL: T10 Torx ® driver 1. Turn off the BRAIN. 2. Use a T10 Torx driver to remove the single screw located at the bottom of the BRAIN side plate (if the side plate is installed). Remove the BRAIN side plate 3.
R E D D S M C O P E R AT I O N G U I D E INSTALL THE RED SWITCHBLADE-M WARNING: Before installing or removing the RED Switchblade-M, you MUST turn off the BRAIN. REQUIRED TOOL: T10 Torx ® driver 1. Turn off the BRAIN. 2. Use a T10 Torx driver to remove the single screw located at the bottom of the BRAIN side plate (if the side plate is installed). 3. Rotate the BRAIN side plate upwards to disengage the lip at the top of the side plate from the BRAIN, and remove the BRAIN side plate. 4.
R E D D S M C O P E R AT I O N G U I D E INSTALL THE MODULE ADAPTOR You must install an adaptor module on the back of the BRAIN before you install a DSMC module. REQUIRED TOOL: T20 Torx ® driver 1. Turn off the BRAIN. 2. Remove the REDMOTE, if attached. 3. Position the Module Adaptor over the V-mount on the rear of the BRAIN. Install Module Adaptor 4. Apply pressure and tighten the four (4) captive screws in a cross pattern (“X” pattern) approximately two (2) turns each using a T20 Torx driver.
R E D D S M C O P E R AT I O N G U I D E REMOVE THE MODULE ADAPTOR 1. Turn off the BRAIN. 2. Use a T20 Torx driver to loosen the screws attaching the Module Adaptor to the BRAIN. 3. Remove the Module Adaptor from the BRAIN. INSTALL THE +1 ADAPTOR MODULE REQUIRED TOOL: T20 Torx driver 1. Turn off the BRAIN. 2. Remove the REDMOTE, if attached. 3. Position the +1 Adaptor Module over the V-mount on the rear of the BRAIN. Install the +1 Module Adaptor COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E 4. Insert the HDMI connector into the HDMI port on the BRAIN. Insert the HDMI Connector to the BRAIN 5. Apply pressure and tighten the four (4) captive screws in a cross pattern (“X” pattern) approximately two (2) turns each using a T20 Torx driver. DO NOT FULLY TIGHTEN. Install screws 6. Fully tighten the four (4) screws in a cross pattern (“X” pattern). DO NOT OVERTIGHTEN. REMOVE THE +1 ADAPTOR MODULE REQUIRED TOOL: T20 Torx driver 1. Turn off the BRAIN. 2.
R E D D S M C O P E R AT I O N G U I D E ATTACH A DSMC MODULE REQUIRED TOOL: T20 Torx driver 1. Turn off the BRAIN. 2. Insert the lip at the top of the module into the recess at the top of the adaptor module. Insert Module Lip 3. Rotate the module down flush with the rear of the adaptor module. Press Module Flush 4. Apply pressure and use a T20 Torx driver to turn the lock on the bottom of the adaptor module clockwise into the Lock position. REMOVE A DSMC MODULE REQUIRED TOOL: T20 Torx driver 1.
R E D D S M C O P E R AT I O N G U I D E REPLACE THE HOOD SCOOP The hood scoop on some EPIC-X and EPIC-M models extends beyond the rear plane of the BRAIN. RED offers shorter hood scoops so that you can attach an LCD or other accessory to the mounting locations on the top of the +1 Adaptor Module. Replace the Hood Scoop To replace DSMC fan hood scoop, follow the instructions below:. 1. Turn off the BRAIN. 2. Use a T8 Torx driver to remove the four (4) M3x0.5 x 6 mm cap screws holding the hood scoop.
R E D D S M C O P E R AT I O N G U I D E USE A TRIPOD OR MONOPOD This section describes the DSMC mounting points and mounting equipment for use with a tripod or monopod. The DSMC is equipped with two (2) 3/8-16 mounting holes and one (1) 1/4-20 mounting hole on the bottom of the BRAIN. These mounting points are designed for use with a variety of mounting plates and hardware, to support tripods and other support systems.
R E D D S M C O P E R AT I O N G U I D E VIDEO MONITOR OUTPUTS The monitoring path converts RAW sensor data to a white balanced 12-bit depth 1920 x 1080 pixel RGB 4:4:4 video signal. The signal may be modified using ISO, White Balance, or other RGB color space adjustments. The signal is then scaled and gamma-corrected to provide monitor outputs at 10-bit depth in 4:2:2 YCC or 8-bit depth in 4:4:4 RGB. The DSMC offers the following monitor outputs: EVF/LCD: Supports a RED EVF or LCD display.
R E D D S M C O P E R AT I O N G U I D E 04 BASIC MENUS AND CONTROLS This chapter describes the DSMC Basic Menu, controls, including: “Upper Status Row (Basic Menu)” on page 43 “Live Action Area” on page 47 “Lower Status Row” on page 48 “Navigation Controls” on page 51 For more information, go to “Navigation Controls” on page 51 or “Default Key Functions” on page 191.
R E D D S M C O P E R AT I O N G U I D E UPPER STATUS ROW (BASIC MENU) The Upper Status Row displays basic project parameters. The currently selected parameter in the Upper Status Row is underlined with a red bar. The Upper Status Row is also known as the Basic Menu. 9 1 2 3 4 5 6 7 8 Upper Status Row The Upper Status Row includes the following GUI elements: # UPPER STATUS ROW ITEM DESCRIPTION FOR MORE INFORMATION, GO TO...
R E D D S M C O P E R AT I O N G U I D E ACCESS ADVANCED MENUS In the menu for every Upper Status Row item (except for REDCODE) you can select the Advanced... button to access the related menu in the Advanced Menus. For example, select Advanced... in the Frame Rate menu to open Menu > Settings > Project > Frame Rate. For more information about Advanced Menus, go to “Advanced Menus” on page 57. Select “Advanced...” Button “Advanced...” Menu COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E FEATURE: EDIT LIST Select the Edit List... button in the Upper Status Row menus to change the values that display for each setting. For example, if you open the Frame Rate menu and select Edit List..., the camera lets you add or remove values to available frame rates. Select “Edit List...” Button “Edit List...” Menu COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E F STOP (T STOP) The F Stop (also known as the T Stop or aperture) parameter displays when a compatible mount and lens are installed. The aperture controls the depth of field of the image and, in combination with the shutter speed/angle setting, controls the amount of light that reaches the sensor (exposure). Increasing the F stop to a higher number increases the depth of field, but reduces the exposure (brightness).
R E D D S M C O P E R AT I O N G U I D E LIVE ACTION AREA The Live Action Area contains the recorded image area plus Surround View ™ look around area, plus overlays for Frame Guides, Safe Action/Safe Title, Clip Name, and Timecode values. The color of each overlay can be customized to maximize the contrast between the guide(s) and scene being captured.
R E D D S M C O P E R AT I O N G U I D E LOWER STATUS ROW The Lower Status Row provides access to key system information and camera values. 1 2 3 4 5 6 Lower Status Row The Lower Status Row provides key system information and camera values, including: # LOWER STATUS ROW ITEM SUB-ITEM/DESCRIPTION FOR MORE INFORMATION, GO TO...
R E D D S M C O P E R AT I O N G U I D E HISTOGRAM This section describes the elements that comprise the Histogram section in the Lower Status Row. This section of the GUI helps ensure that recorded footage is properly exposed. Tap the Histogram in the Lower Status Row to access the Tools menu. For more information, go to “Tools” on page 58.
R E D D S M C O P E R AT I O N G U I D E GEN INDICATOR Then GEN indicator shows the current genlock status. Gray: No genlock signal is detected, or the signal cannot cross-lock to project (24.00 FPS vs. 23.98 FPS). Red: During process of sync, or genlock is lost while recording. Green: A genlock signal matching the current HD-SDI monitor rate is locked. Yellow: Timing is cross-locked to compatible but not matching monitor rate. For example, genlock is 24.
R E D D S M C O P E R AT I O N G U I D E NAVIGATION CONTROLS This section describes basic controls for navigating the DSMC menus. TOUCHSCREEN NAVIGATION RED Touch displays offer intuitive menu control and four (4) user programmable buttons. 1 2 3 4 RED Touch 7.
R E D D S M C O P E R AT I O N G U I D E NAVIGATION GROUP The Navigation Group is the primary control interface on the DSMC Side Handle, RED Switchblade-M, and REDMOTE.
R E D D S M C O P E R AT I O N G U I D E DSMC SIDE HANDLE This section describes the controls and display of the DSMC Side Handle.
R E D D S M C O P E R AT I O N G U I D E DSMC SIDE HANDLE DISPLAY The DSMC Side Handle displays Basic Menu parameters and other system status information.
R E D D S M C O P E R AT I O N G U I D E RED SWITCHBLADE-M This section describes the controls and display of the RED Switchblade-M.
R E D D S M C O P E R AT I O N G U I D E RED SWITCHBLADE-M DISPLAY The RED Switchblade-M OLED display provides basic camera parameters during operation.
R E D D S M C O P E R AT I O N G U I D E 05 ADVANCED MENUS DSMC ADVANCED MENUS DSMC Advanced Menu The Advanced Menus include: ADVANCED MENU DESCRIPTION FOR MORE INFORMATION, GO TO...
R E D D S M C O P E R AT I O N G U I D E SETTINGS MENU The Settings menu includes: Display, Look, Project, Audio, Recording, Setup, and Maintenance. Settings Menu DISPLAY The Display menu includes: Tools, Zebra, Monitor Control, Modes, Guides, Test Signals, and 4K Broadcast (the 4K Broadcast menu is only accessible when a RED 4K Broadcast Module is installed). TOOLS The Tools menu provides access to false color and display modes.
R E D D S M C O P E R AT I O N G U I D E EXPOSURE Displays color overlay on top of a desaturated image that allows you to check for proper exposure. When enabled, the “E√” indicator displays in the Lower Status Row. The Exposure meter colors indicate the following information: Purple: Underexposed; indicates sensor exposure levels that may be noisy if gained up in post-production. Green: IRE 41–48; based on the RGB levels of the video out signal and not the RAW data.
R E D D S M C O P E R AT I O N G U I D E DISPLAY MODES Display mode options include: Magnify, RAW, and Horizon. MAGNIFY Displays the central region of the sensor in 1:1 pixel resolution. When enabled, the 1:1 text in the Lower Status Row turns green, and the AF Window and the magnified region display. The AF Window determines the center point of the magnified region. If the lens or lens mount is not capable of autofocus with the DSMC, use Confirm mode to turn on the AF Window.
R E D D S M C O P E R AT I O N G U I D E For more information, see the Exposure with RED Cameras: False Color & Zebra Tools article available at www. red.com/learn/red-101/exposure-false-color-zebra-tools. ENABLE ZEBRA INDICATORS 1. Go to Menu > Settings > Display > Zebra. 2. Select a Zebra check box. 3. Select the low and high IRE values. Each value range is 1–100. ‒ ‒ Zebra 1: Areas of the image exposed within the IRE range are indicated by diagonal lines at –45°. Default is IRE 98–100.
R E D D S M C O P E R AT I O N G U I D E OVERLAY Select which overlay shows on top of the video. RED provides preset overlays, which have “(RED)” in the overlay name. Create custom overlays in the Overlay tab. For more information, go to “Overlay” on page 64. RESOLUTION Select the output resolution for HDMI and HD-SDI monitors (you cannot select a resolution for LCD and EVF monitors, since these are determined automatically).
R E D D S M C O P E R AT I O N G U I D E FRAMED OVERLAY The video display is scaled down on the monitor so that the overlay items fit outside of the video area rather than over it. This setting only affects the monitor, and not affect captured footage. Framed Overlay AUTO HIDE MENUS Hides the Upper Status Row and Lower Status Row. When this option is disabled, the video is scaled so that the menus are not overlaid on the video. When this option is enabled, the video is not scaled.
R E D D S M C O P E R AT I O N G U I D E OVERLAY Create custom overlays that include specific items. Overlays can be stored on the camera or transferred to SSD to be shared with other cameras. Camera: Overlays saved internally on the camera display in the Overlay drop-down menu on the Monitor Control > Monitor tab. Media: Overlays saved to an SSD can be found at S-SSD\Overlays. NOTE: Overlays that end with (RED) are provided by default and cannot be edited, deleted, or exported.
R E D D S M C O P E R AT I O N G U I D E Clip Name (CLIP) is on the bottom left, and the Timecode (TC) is on the bottom right. Selecting one (1) of the buttons opens a new dialog that lets you choose a user interface element. 6. Select the Item that you want to add. 7. Select the Size of the item. 8. If adding a Custom Label (LBL), enter the Custom Text for that item. 9. Select Add to return to the previous screen. 10. Add all of the items to the overlay. 11. Select Create or Save.
R E D D S M C O P E R AT I O N G U I D E BRIGHTNESS Control the brightness of each LCD and EVF. Move to the right for a brighter display; move to the left for a dimmer display. NOTE: A rear LCD/EVF is an LCD/EVF that is plugged into any rear RED module, such as the +1 Adaptor Module or the Pro I/O Module. ADVANCED Provides access to additional gestures, settings, and themes. GESTURES Pinch to Magnify: Use two fingers to pinch inward OR slide apart on the LCD to toggle 1:1 Magnify.
R E D D S M C O P E R AT I O N G U I D E DISPLAY MODES Use the Modes menu to determine how the following settings display: Camera Lens CAMERA TAB Display Mode: Camera EXPOSURE Time (Absolute): Displays the exposure time in seconds (1/xx sec). When you change the frame rate in this mode, the shutter time stays the same, but the shutter angle changes. Time (Absolute) is the default. Angle (Relative): Displays the exposure as an angle (1–360°).
R E D D S M C O P E R AT I O N G U I D E LENS TAB Display Mode: Lens APERTURE (F STOP) 1/4 F#: F Stop (aperture) increments in 1/4 stops. 1/3 F#: F Stop (aperture) increments in 1/3 stops. (Default) FOCUS DISTANCE Metric: Displays lens focus distances in meters. Imperial: Displays lens focus distances in feet and inches. (Default) Motion Mount ND AND MOTION MOUNT ISO PULL Only applicable when using a DSMC ® RED Motion Mount TM .
R E D D S M C O P E R AT I O N G U I D E WIDTH/HEIGHT The Width/Height fields replace the Scale field when you select Absolute from the Mode drop-down menu. Select the values for the width and height of the guide in pixels. OFFSET X/Y Percentage to offset guide from its default centered position. Available range is 0–100%. 100%: Right-aligned (for X offset) and bottom-aligned (for Y offset). -100%: Left-aligned (for X offset) and top-aligned (for Y offset).
R E D D S M C O P E R AT I O N G U I D E COLOR Saturation: Adjusts color saturation. Range is 0.0 (monochrome) to 4.0 (super color). Default is 1.0. Contrast: Adjusts the overall contrast of the image. Range is –1.0 (flat) to 1.0 (max contrast). Default is 0.0. Brightness: Adjusts brightness without crushing highlights. Available range is –10.0 to 10.0. Default is 0.0. Exposure: Adjusts exposure compensation. Available range is –7.0 to 7.0. Default is 0.0.
R E D D S M C O P E R AT I O N G U I D E COLOR SPACE AND GAMMA SPACE RED recommends using the most recently released Color Space and Gamma settings. Use legacy settings (such as REDcolor2) only if you need to record footage to match footage that you recorded with that legacy setting. For more information, see the Understanding REDlogFilm and REDgamma article available at www.red.com/ learn/red-101/redlogfilm-redgamma. COLOR TEMPERATURE Select a color temperature.
R E D D S M C O P E R AT I O N G U I D E The default sensor frame rate is 23.98 FPS. If you change the project time base, the sensor frame rate automatically changes its value to match the project time base. PROJECT TIME BASE Select the project time base, which is the rate at which the footage will be played back. The project time base displays in the lower left corner of the display. The following project time bases are available: 23.98 FPS (default) 24.00 FPS 25.00 FPS 29.97 FPS 47.
R E D D S M C O P E R AT I O N G U I D E EPIC DRAGON FRAME RATES The table below describes the maximum frame rate for each resolution of the EPIC DRAGON. The minimum frame rate is always 1 FPS. The table below omits rows for the anamorphic formats, since the maximum frame rate for each anamorphic format and the corresponding non-anamorphic format is the same. NOTE: Frame rates below are based on a 23.98 time base, 8:1 compression, and Lookaround disabled.
R E D D S M C O P E R AT I O N G U I D E FORMAT MAX FRAME RATE (FPS) FORMAT MAX FRAME RATE (FPS) 4K 6:5 121.05 2K 6:5 240.55 4K 3:2 102.24 2K 3:2 203.37 4K 4:3 90.932 2K 4:3 180.99 4K 5:4 85.27 2K 5:4 169.78 4K 4:1 253.52 2K 4:1 400.00 4K 8:1 400.00 2K 8:1 400.00 3.5K FF 139.24 COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E SCARLET DRAGON FRAME RATES The table below describes the maximum frame rate for each resolution of the SCARLET DRAGON. The minimum frame rate is always 1 FPS. NOTE: Frame rates below are based on a 23.98 time base, 8:1 compression, with Lookaround disabled. FORMAT MAX FRAME RATE (FPS) 6K FF 12.08 (in Burst mode) 5K FF 24.62 5K 2:1 25.95 5K WS 30.71 5K HD 26.24 5K 6:5 38.63 4K FF 38.61 4K 2:1 40.87 4K WS 48.22 4K HD 41.16 4K 6:5 60.
R E D D S M C O P E R AT I O N G U I D E EPIC MYSTERIUM-X AND SCARLET MYSTERIUM-X FRAME RATES The table below describes the maximum frame rate for each resolution of the EPIC MYSTERIUM-X and SCARLET MYSTERIUM-X. The minimum frame rate is always 1 FPS. The table below omits rows for the anamorphic formats, since the maximum frame rate for each anamorphic format and the corresponding non-anamorphic format is the same. NOTE: Frame rates below are based on a 23.
R E D D S M C O P E R AT I O N G U I D E EXPOSURE Select the exposure (shutter speed) of each frame. You can change exposure while recording. Decreasing shutter speed increases the amount of time that light hits the sensor, which increases exposure and motion blur of moving objects. Increasing shutter speed decreases the amount of time that light hits the sensor, which decreases exposure and motion blur of moving objects. The Upper Status Row displays the exposure as either shutter speed or shutter angle.
R E D D S M C O P E R AT I O N G U I D E TIMECODE For more information about timecode, go to “Timecode, Genlock, Multi-Camera Setup” on page 143. TIMECODE SOURCE MODE DESCRIPTION User Provided (Internal) Use Real Time Clock (RTC) Uses the internal Real Time Clock as the timecode counter source. You can set the hours, minutes, and seconds in the numerical boxes on the screen. Set Manually Define a custom value as the timecode counter seed.
R E D D S M C O P E R AT I O N G U I D E FORMAT Use the Format menu to select the resolution, aspect ratio, anamorphic setting, and lookaround setting. After selecting format settings, select Set Format. EPIC DRAGON FORMATS The table below describes the formats that are available for EPIC DRAGON. Default for EPIC DRAGON is 6K 2:1. The table below omits rows for the anamorphic formats, since the pixel dimensions for each anamorphic format and the corresponding non-anamorphic format are the same.
R E D D S M C O P E R AT I O N G U I D E RESOLUTION DESCRIPTION DIMENSIONS (PIXELS) WIDTH HEIGHT 4.5K 4:1 4.5K RAW 4:1 4608 1152 4.5K 8:1 4.5K RAW 8:1 4608 576 4K FF 4K RAW Full Frame 4096 2160 4K 2:1 4K RAW 2:1 4096 2048 4K WS 4K RAW Wide Screen—2.
R E D D S M C O P E R AT I O N G U I D E RESOLUTION DESCRIPTION DIMENSIONS (PIXELS) WIDTH HEIGHT 2.5K 4:3 2.5K RAW 4:3 2400 1800 2.5K 5:4 2.5K RAW 5:4 2400 1920 2.5K 4:1 2.5K RAW 4:1 2560 640 2.5K 8:1 2.5K RAW 8:1 2560 320 2K FF 2K RAW Full Frame 2048 1080 2K 2:1 2K RAW 2:1 2048 1024 2K WS 2K RAW Wide Screen—2.
R E D D S M C O P E R AT I O N G U I D E SCARLET DRAGON FORMATS The table below describes the formats that are available for SCARLET DRAGON. SCARLET DRAGON offers a 6:5 aspect ratio for each resolution. Using a 6:5 aspect ratio at 2x anamorphic gives you a 2:40:1 aspect ratio. RESOLUTION DESCRIPTION DIMENSIONS (PIXELS) WIDTH HEIGHT 6K 6K RAW Full Frame 6144 3160 6K 6:5 6K RAW 6:5 3792 3160 5K 5K RAW Full Frame 5120 2700 5K 2:1 5K RAW 2:1 5120 2560 5K WS 5K RAW Wide Screen—2.
R E D D S M C O P E R AT I O N G U I D E EPIC MYSTERIUM-X AND SCARLET MYSTERIUM-X FORMATS The table below describes the formats that are available for EPIC MYSTERIUM-X and SCARLET MYSTERIUM-X. EPIC MYSTERIUM-X: Default is 5K 2:1. SCARLET MYSTERIUM-X: Default is 4K. The table below omits rows for the anamorphic formats, since the pixel dimensions for each anamorphic format and the corresponding non-anamorphic format are the same. For more information, go to “Anamorphic” on page 84.
R E D D S M C O P E R AT I O N G U I D E ASPECT RATIO Select the Aspect Ratio. The available aspect ratios are determined by the selected resolution. For a list of aspect ratios for EPIC DRAGON, go to “EPIC DRAGON Formats” on page 79. For a list of aspect ratios for SCARLET DRAGON, go to “SCARLET DRAGON Formats” on page 82. For a list of resolutions for EPIC MYSTERIUM-X and SCARLET MYSTERIUM-X, go to “EPIC MYSTERIUM-X and SCARLET MYSTERIUM-X Formats” on page 83.
R E D D S M C O P E R AT I O N G U I D E SHORT-CUT TO INDUSTRY-STANDARD ANAMORPHIC FORMATS To quickly access industry-standard anamorphic formats, go to Menu > Settings > Project > Format > Anamorphic. The Anamorphic tab is a short-cut to all of the industry-standard anamorphic formats, so that you can easily select the most common anamorphic formats. The Anamorphic tab lists the following anamorphic formats: EPIC DRAGON: Every format with a 5:4 or 4:3 aspect ratio and a 1.3x or 2x anamorphic setting.
R E D D S M C O P E R AT I O N G U I D E CONTINUOUS RECORD Continuous Record is the “normal” recording mode. The camera continuously records frames at the current sensor frame rate. You can limit each recording to a specific amount of frames using the Limit Recording to setting. INTERNAL TIMELAPSE TIMER In Internal Timelapse Timer mode, the camera records a specified number of frames at a specified interval. The current sensor frame rate determines the timing of the frames per pulse.
R E D D S M C O P E R AT I O N G U I D E 5. Close the menu. 6. Start recording. PRE COUNT AND POST COUNT When Frame Trigger or Burst mode is enabled, select the number of frames for the Pre Count and Post Count: Pre Count: The camera captures the frame cache from the time preceding the marker. Post Count: The camera captures the remaining frame cache after the marker. The maximum frame counts are listed in the Available column, and are based on format and REDCODE.
R E D D S M C O P E R AT I O N G U I D E EXTERNAL RECORD ONLY External Record Only mode allows for external recording only. That is, the recording is NOT saved to the SSD, and external recording is blocked if an SSD is mounted to the camera. An external recorder is required and can be triggered automatically via HD-SDI (if supported by the recorder). FRAME PROCESSING NOTE: Frame processing is not supported in Speed Ramp Mode. For more information, go to “Speed Ramp Mode” on page 87.
R E D D S M C O P E R AT I O N G U I D E PRE-RECORD When enabled, the Pre-Record setting continuously captures a cache of footage before recording starts. Select to have 4–30 seconds (incremented at two second intervals) of pre-record time added to the actual footage. When Pre-Record is enabled, you won’t miss the start of a shot by being a little slow on the trigger. Pre-Record Duration: Select the pre-record time.
R E D D S M C O P E R AT I O N G U I D E OPTIONS MENU key returns to settings menu: Pressing the Menu key on a side module or REDMOTE moves you up one level in the menu tree.
R E D D S M C O P E R AT I O N G U I D E CAMERA NAME Use the Camera menu to set up a unique identifier for your camera (or a group of cameras). All command filtering happens on the receiver side of the communication link. Use camera names and group names to address commands to a specific camera or group of networked cameras. Name: Enter a unique camera name to use in network communications. The field is limited to eight (8) characters.
R E D D S M C O P E R AT I O N G U I D E ETHERNET Use the settings on the Network tab to configure the GIG-E port. Each camera or device requires a unique IP address. For camera-to-camera communication via Ethernet, both cameras need to be in the same sub-net (have the same netmask address) and have the same gateway address. DHCP: Enables DHCP.
R E D D S M C O P E R AT I O N G U I D E SENSOR SYNC MODE Sensor Sync Mode allows the shutter timing (scan start) to sync to an external signal. Off: Sensor runs at the current sensor frame rate. This is the default option. Genlock: Sensor synchronizes with the incoming compatible genlock signal. MoCo: Each rising edge on the sync input triggers a frame to be captured.
R E D D S M C O P E R AT I O N G U I D E PRO I/O GPIO AND PRO I/O SW Use the PRO I/O GPI and PRO I/O SW menus to map input and output (I/O) actions to the GPIO and AUX connectors on the Pro I/O Module. Low and High refer to the voltage. In practice, Low/High correlate to the press/release of a trigger or the on/ off position of a switch. Low: The falling edge (transition from high voltage to low voltage). High: The rising edge (transition from low voltage to high voltage).
R E D D S M C O P E R AT I O N G U I D E GPIO CONNECTOR This table describes the I/O options for the GPIO connector on the Pro I/O Module: I/O OPTION DEFAULT ACTION PIN 1 4 GPI A High Key Disabled 2 GPI A Low Record: Toggle 2 2 3 AUX CONNECTOR This table describes the I/O options for the AUX connector on the Pro I/O Module: I/O OPTION DEFAULT ACTION PIN GPI B High Key Disabled 6 GPI B Low Record: Toggle 6 SW 1 High Key Disabled 7 SW 1 Low Go to: Playback 7 SW 2 High Key Disabled
R E D D S M C O P E R AT I O N G U I D E FAN CONTROL MODES Select a fan control mode for the bottom fan. If a top fan is installed, it runs at a constant speed when necessary. NOTE: After selecting a new fan setting, run the DSMC until the core temperature stabilizes, and then perform a black shading calibration. NOTE: If using a top fan, the top fan may not run immediately after turning on the DSMC, as the top fan runs when the DSMC requires additional cooling power.
R E D D S M C O P E R AT I O N G U I D E LENS LENS TAB The options displayed on the Lens tab change based on the attached lens mount. PL MOUNT Enable Power to Lens: Ensures that the BRAIN powers the lens via the lens mount. This feature is enabled by default, but the camera saves the last selected setting. Deselect when using the Fujinon 19-90mm T2.9 Cabrio Premier PL lens. If you disable this feature for the Fujinon Cabrio, re-enable it when using other lenses.
R E D D S M C O P E R AT I O N G U I D E CALIBRATE The Calibrate menu includes: Sensor, Gyro/Acc, and Lens. SENSOR CALIBRATION Sensor calibration, also known as black shading, is a process during which the camera optimizes image quality by ensuring that pixel sensitivity remains consistent throughout the sensor. Black shading generates a calibration map based on system and environment settings.
R E D D S M C O P E R AT I O N G U I D E caps are made to protect the lens, not necessarily to block light.) ‒ ‒ If possible, use a dark room. ‒ ‒ Just closing the aperture is NOT sufficient. 4. Ensure a properly formatted SSD is attached to the camera. Even if you are not saving the calibration map to the DSMC, an SSD is required to store RAW images during calibration. 5. Go to Menu > Settings > Maintenance > Calibrate > Sensor.
R E D D S M C O P E R AT I O N G U I D E CALIBRATION MAP NAMING CONVENTIONS Each calibration map has a unique name that uses the format described in the table below: NAME DESCRIPTION EXAMPLE Exposure Current exposure; to set exposure, go to Menu > Setting > Projects > Exposure 48 Sensor Temperature Sensor temperature (Celsius); in the Lower Status Row, this is the number to the left of the forward slash (Temp: 34/35) 32C Year Year that the calibration map is created (yyyy) 2014 Month Month that
R E D D S M C O P E R AT I O N G U I D E GYROSCOPE AND ACCELEROMETER CALIBRATION The internal three-axis gyroscope and three-axis accelerometer need to be calibrated for the Horizon overlay to function properly. The Gyro/Acc calibration file is stored in the flash memory of the BRAIN, so you DO NOT need to recalibrate after restoring the camera or upgrading firmware. For more information, go to “Horizon” on page 60. To calibrate the Horizon overlay, follow the instructions below: 1.
R E D D S M C O P E R AT I O N G U I D E CREATE LENS CALIBRATION FILES The calibration process creates a calibration file for the current focal length of the electronic lens. Calibrate the lens at each available focal length to create a full lens calibration file. 1. Attach a DSMC Canon Mount or DSMC Nikon Mount to the BRAIN. 2. Attach an electronic lens. 3. Manually set the first focal length you want to calibrate. 4.
R E D D S M C O P E R AT I O N G U I D E The lens calibration process for the current focal length starts and a progress bar displays. Once the calibration process starts, DO NOT touch the lens, as doing so may cause the lens to calibrate incorrectly. 5. Select OK after the calibration file is created. 6. To calibrate the next focal length, follow the instructions below: A. Go to Menu > Settings > Maintenance > Calibrate > Lens. B. Select the calibration file name in the Camera list and select Edit....
R E D D S M C O P E R AT I O N G U I D E C. Manually set the next focal length. D. Select Add Cal @ xx..., where “xx” is the current focal length. NOTE: If you calibrate a focal length that has already been calibrated, the new files overrides the previous file. The lens calibration process for the current focal length starts and a progress bar displays. Once the calibration process starts, DO NOT touch the lens, since that may cause incorrect calibration. 7.
R E D D S M C O P E R AT I O N G U I D E VIEW AND MODIFY LENS CALIBRATION INFORMATION 1. Go to Menu > Settings > Maintenance > Calibrate > Lens. 2. Select the calibration file name in the Camera list and select Edit.... The following information displays: ‒ ‒ Mount Type ‒ ‒ Focal Length ‒ ‒ F Stop Range: Overall F stop range of lens. ‒ ‒ Lens Status ‒ ‒ Calibrated Focal Lengths 3. You can perform any of the following actions: ‒ ‒ Add Cal @ xx...
R E D D S M C O P E R AT I O N G U I D E EXPORT AND IMPORT LENS CALIBRATION FILES Lens calibration files can be stored on the camera or transferred to SSD to be shared with other cameras. When exporting lens calibration files from camera to SSD, the files are saved to a folder on the SSD called “lens_cal”. DO NOT change the file name of the calibration file after you save it to an SSD. All : Export selected file from camera to SSD. : Export all files from camera to SSD.
R E D D S M C O P E R AT I O N G U I D E SELF TEST The Self-Test menu includes: Enable Sensor Test Pattern and Touchscreen. ENABLE/DISABLE SENSOR TEST PATTERN The Sensor Test Pattern feature is only used during manufacturing. The sensor test pattern is a white screen. TOUCHSCREEN To perform a touchscreen self-test, follow the instructions below: 1. Go to Menu > Settings > Maintenance > Self Test. 2. Select Touchscreen. A grid of green squares displays on the touchscreen. 3.
R E D D S M C O P E R AT I O N G U I D E REDISCOVER Rediscovers all hardware and caches the data for future boot cycles. To perform a Hardware Rediscover, follow the instructions below: 1. Go to Menu > Settings > Maintenance. 2. Select Rediscover. 3. Select Yes on the screen that asks you to confirm the Hardware Rediscover. The camera turns off. 4. Turn on the camera.
R E D D S M C O P E R AT I O N G U I D E OLPF RED offers multiple optical low-pass filters (OLPFs) for EPIC DRAGON and SCARLET DRAGON. Each OLPF optimizes certain characteristics to take full advantage and control of each shooting environment. The camera checks the OLPF type, and adjusts the color scienced based on the selected OLPF. CHECK INSTALLED OLPF To see which OLPF is installed, follow the instructions below: 1. Go to Menu > Settings > Maintenance > OLPF.
R E D D S M C O P E R AT I O N G U I D E MEDIA MENU The Media Menu is used to format and eject (unmount) the SSD. Media Menu For more information about using media, see the RED DSMC Media Operation Guide, available at www.red. com/downloads. PLAYBACK MENU To view clips from the SSD, go to Menu > Playback. PLAYBACK MENUS In Playback mode, the menu is pared-down, so you can’t access all menus. Some menus offer different options. MEDIA Lists all available clips on the attached SSD.
R E D D S M C O P E R AT I O N G U I D E PLAYBACK CONTROLS The images below show the Playback controls. 3 1 4 5 6 7 8 9 2 14 20 Playback Controls 10 11 12 13 Play Options 15 16 17 18 19 Marker Options COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E The table below describes the Playback controls. # CONTROL DESCRIPTION 1 Playback/Record toggle Toggles between Record mode and Playback mode. 2 Histogram Displays the clip histogram. The histogram changes when Look settings change. For more information, go to “Looks” on page 124. If using the touchscreen, touch the histogram to open the Tools menu. 3 Load Previous Clip Loads the previous clip in the playlist.
R E D D S M C O P E R AT I O N G U I D E POWER MENU The Power menu displays the power status of all attached power sources and allows you to turn off the camera. NOTE: For more information about powering the DSMC, see the DSMC Power Operation Guide, available at www.red.com/downloads. POWER IN The power status displays for the BRAIN DC, DSMC Side Handle, Rear 1, Rear 2, Rear 3, and Rear 4.
R E D D S M C O P E R AT I O N G U I D E HDR MENU NOTE: HDR mode cannot be modified when in Magnify 1:1 mode or when test signals are enabled. NOTE: You cannot use HDR mode when: ‒ ‒ A Motion Mount is installed. ‒ ‒ A Sensor Sync Mode (Genlock or MoCo) is enabled. ‒ ‒ Speed Ramp mode is enabled. ‒ ‒ A Frame Processing mode (Frame Summing or Frame Averaging) is enabled. By default HDRx is disabled, and the HDR indicator in the Lower Status Row is gray. To enable HDRx, follow the instructions below: 1.
R E D D S M C O P E R AT I O N G U I D E FOCUS MENU The Focus menu includes: Mode and Rack. MODE TAB The Mode Tab is used to enable and select Focus parameters, including Mode, Zone, Size, and Enhanced A/F. Focus Menu: Mode MODE Select one (1) of the following from the Mode drop-down menu: Manual: When selected, all focus operations are manual. Confirm: Enables the Center or Spot focus target.
R E D D S M C O P E R AT I O N G U I D E In Single, Continuous, and Touch Track modes, a single target displays on the screen that indicates where the image will be in focus. In Rack mode, multiple targets display on the screen to indicate the different areas between which the camera will rack focus. Press the key mapped to AF Mode: Cycle (REDMOTE/DSMC Side Handle button A default) to cycle through the Focus Mode options in order.
R E D D S M C O P E R AT I O N G U I D E MOVE THE SPOT FOCUS TARGET Move Spot target with touchscreen: Tap and hold the touchscreen on the location you want to relocate the Spot target. Tap and hold the touchscreen where the Spot target currently is, and drag the Spot target. Move Spot target with DSMC Side Handle or REDMOTE: 1. Go to the main screen. 2. Press the Down Arrow in the Navigation Group. The Spot target line weight increases and the red cursor under Menu dims slightly. 3.
R E D D S M C O P E R AT I O N G U I D E 8. Close the Focus menu. The target displays on the touchscreen, and the monitor that you selected for the Enhanced A/F feature is in Clean mode. RACK FOCUS Use the Rack tab to configure up to four (4) focus points and execute rack focus between them. SET UP RACK FOCUS 1. Ensure that a DSMC Nikon Mount, DSMC Canon Mount, or DSMC Canon Motion Mount is installed and that a supported lens is attached to the BRAIN. 2. Go to Menu > Focus > Mode. 3.
R E D D S M C O P E R AT I O N G U I D E 4. Select a size from the Size drop-down menu. 5. Go to the Rack tab. 6. Use the Rack Speed slider to change the speed at which the lens moves. Move the slider to the left for a slower speed, and to the right for a faster speed. 7. Select the number of rack points (1–4) from the Rack Points drop-down menu. A line for each rack point displays, indicated by the letters A, B, C, and D. The focus distance displays for each rack point. 8.
R E D D S M C O P E R AT I O N G U I D E 9. To set a rack point location, follow the instructions below: A. Select the rack point: A, B, C, or D. B. Select Close to return to the main screen. C. Tap and hold the touchscreen where you want the rack point to be, or press and drag the rack point. When you move a rack point, the camera autofocuses. NOTE: To prevent a rack point from being accidentally moved, the rack point is less sensitive to touch than the other focus targets.
R E D D S M C O P E R AT I O N G U I D E EXPOSURE ASSIST The Exposure Assist menu provides access to settings for the Auto Exposure (AE) feature. The AE feature maintains a constant image brightness, even if the actual scene brightness changes. The AE feature is different than traditional AE, in that RED AE only controls the amount of light that hits the sensor, either by adjusting F stop or exposure.
R E D D S M C O P E R AT I O N G U I D E METERING Metering determines the area of the sensor that is used for brightness evaluation: Spot: Weights the measurement to the center 5% of the sensor, approximately. Center: Weights the measurement to the center 25% of the sensor, approximately. Average: Averages the entire image area of the sensor. SPEED The Speed setting determines how quickly the algorithm adapts to changing light. Slow: Settings adapt in small steps.
R E D D S M C O P E R AT I O N G U I D E PRESETS MENU The DSMC has three types of presets: Camera Presets: These store and recall camera setup information, such as in-camera Looks, key mappings, I/O configurations, and more. The DSMC has a number of factory-installed presets. Looks: These allow you to save the specific color, image, white balance, and detail settings to be used for other projects. Looks that are generated in-camera display on the Camera Presets tab.
R E D D S M C O P E R AT I O N G U I D E EXPORT AND IMPORT PRESETS Presets can be stored on the camera or transferred to SSD to be shared with other cameras. When exporting presets from camera to an SSD, the presets are saved to a folder on the SSD called “Presets”. When importing presets from an SSD to camera, the presets must be stored on the SSD in a folder called “Presets”. : Export selected preset from camera to SSD. All : Export all presets from camera to SSD.
R E D D S M C O P E R AT I O N G U I D E MANAGE IMPORTED LOOKS Manage Looks imported from REDCINE-X PRO in the Presets > Looks tab. When exporting Looks from camera to SSD, the Looks are saved to a folder on the SSD called “Looks”. You can perform the following actions with imported Looks: All : Export selected Looks from camera to SSD. : Export all Looks from camera to SSD. Apply: Apply the selected Look. Delete...: Delete the selected Look.
R E D D S M C O P E R AT I O N G U I D E 06 RECORD AND MONITOR AUDIO OVERVIEW The DSMC can record up to two (2) discrete stereo channels of uncompressed 24-bit, 48 KHz audio. A Pro I/O Module provides two (2) channels of microphone level or line level audio inputs, and up to four (4) digital AES audio inputs. In total, the DSMC supports eight (8) incoming audio channels, and can record up to four (4) audio channels.
R E D D S M C O P E R AT I O N G U I D E SET UP AUDIO To set up audio, go to Menu > Settings > Audio, and adjust the input, pre-amplifier, headphone, and mix settings.
R E D D S M C O P E R AT I O N G U I D E LINK Gain Sliders: Ensures that each pre-amplifier (Pre-Amp) slider has the same value. If you select the check box while the sliders have different values, you must change one (1) slider for all sliders to sync up. Volume Sliders: Ensures that each headphone (Headphone) slider has the same value, so that you can control the master volume for headphones.
R E D D S M C O P E R AT I O N G U I D E PRE-AMP The pre-amplifier range is 30 dB to 60 dB. The default is 32 dB. To adjust amplification levels, follow the instructions below: 1. Go to Menu > Settings > Audio > Pre-Amp. 2. Move the Pre-Amp (pre-amplifier) sliders up and down to adjust the amplification levels. NOTE: To link the amplification for each channel, go to Menu > Settings > Audio > Channel and select the Gain Sliders check box. For more information, go to “Link” on page 128.
R E D D S M C O P E R AT I O N G U I D E AUDIO OUTPUT OPTIONS DSMC BRAIN: One (1) 2-channel headphone output. For maximum quality, use high impedance headphones. Pro I/O Module: One (1) XLR connector that supports 2-channel line level analog output. The signal strength of the line out cannot be controlled, and is fixed at –15 dB gain. HDMI and HD-SDI monitor: Both output two (2) channels of 24-bit 48 KHz uncompressed, embedded digital audio.
R E D D S M C O P E R AT I O N G U I D E You can control the volume and stereo for each audio monitoring option: Cam Mix (Camera Mix): Headphones plugged into the DSMC BRAIN. Rear Mix: Line out plugged into the Pro I/O Module. The input gain is fixed. Monitor Mix: External HDMI and HD-SDI monitors that support audio.
R E D D S M C O P E R AT I O N G U I D E AUDIO METER LEVELS The DSMC updates the Audio Meter 12 times per second with the maximum signal from the last 1/12 of a second period. The range of the Audio Meter is –52 dBFS to 0 dBFS.
R E D D S M C O P E R AT I O N G U I D E 07 REDMOTE OPERATION OVERVIEW REDMOTE The REDMOTE is a remote camera control unit for the DSMC that attaches to the rear of the BRAIN or other expansion module. When detached from the DSMC, the REDMOTE provides wireless camera control using the proprietary REDLINK™ protocol.
R E D D S M C O P E R AT I O N G U I D E CONTROLS, CONNECTORS, AND LEDS This section describes the REDMOTE controls, connectors, and color LCD display. 3 8 4 1 5 2 12 9 10 6 2 13 11 7 REDMOTE The following table describes default REDMOTE control actions. Each control is also user programmable.
R E D D S M C O P E R AT I O N G U I D E SOFT MENU BUTTONS (1-3) There are three (3) Primary Soft Menu Buttons located below the left side of the REDMOTE LCD. These buttons provide quick access to REDMOTE advanced operations. Button 1: Access Connect Menu. Button 2: Toggle between Local and Remote Modes. Button 3: Access Setup Menu. REDMOTE CONTROL MODES Press Button 2 to toggle between Remote Mode and Local Mode.
R E D D S M C O P E R AT I O N G U I D E REDMOTE BASICS This section describes the common REDMOTE operations. DOCK THE REDMOTE 1. Position the REDMOTE V-Mount dock over the V-Mount on the BRAIN or rear module. 2. Slide the REDMOTE down until you hear a click, which indicates the REDMOTE is securely attached. NOTE: Docking the REDMOTE automatically pairs the REDMOTE with the camera when the DSMC is turned on and wireless settings are enabled. UNDOCK THE REDMOTE 1.
R E D D S M C O P E R AT I O N G U I D E DOCK TO PAIR 1. Turn on the BRAIN. 2. Dock the REDMOTE to the back of the BRAIN or rear module. NOTE: When the REDMOTE is removed from the DSMC, it automatically scans for the wireless signal and connects to that DSMC. PAIR WIRELESSLY 1. Turn on the BRAIN. 2. Go to Menu > Settings > Setup > REDMOTE. 3. Select Scan for REDMOTEs. 4. When the scan is complete, select the REDMOTE from the scan list. 5. Select Pair ->. 6. Select Close to exit the menu.
R E D D S M C O P E R AT I O N G U I D E CHARGE THE REDMOTE A fully discharged REDMOTE battery requires approximately six (6) hours to fully charge. You can use the REDMOTE while it charges. Charge the REDMOTE using either of the following methods: Dock the REDMOTE to a camera or rear module. Connect the REDMOTE to a computer, cell phone charger, or other sufficient power source using the RED Mini-USB-to-USB cable.
R E D D S M C O P E R AT I O N G U I D E REDMOTE LCD DISPLAY MENU The REDMOTE LCD displays key camera settings of a paired and connected DSMC. There are five (5) available REDMOTE Setting menus, accessible with the Soft Menu Buttons (4-8). NOTE: Soft Menu Buttons 7 and 8 are not defined.
R E D D S M C O P E R AT I O N G U I D E UPGRADE REDMOTE FIRMWARE This section describes the REDMOTE firmware upgrade process using Mac, PC, and the DSMC. UPGRADE REDMOTE WITH DSMC When you dock a REDMOTE, the DSMC checks to see if the REDMOTE is running the latest firmware. If the REDMOTE firmware is slightly outdated, you have the option to update the REDMOTE firmware through the DSMC. If REDMOTE firmware is severely outdated, you will be instructed to install updates via USB.
R E D D S M C O P E R AT I O N G U I D E UPGRADE REDMOTE FIRMWARE (MACINTOSH) 1. Download the REDMOTE Firmware, available at www.red.com/downloads. NOTE: Review the read_me_redmote_vX.X.XX instructions contained in the REDMOTE_vX.X.XX.zip file. 2. Uncompress the zip file. 3. Open the REDMOTE_vX.X.XX folder. 4. Click Select File in REDMOTE Upgrade Utility. 5. Open the redmote.1.bin file in the REDMOTE_Firmware_vX.X.XX folder. “Selected File: redmote.1.bin” displays. 6. Click Start Upgrade.
R E D D S M C O P E R AT I O N G U I D E CONFIGURE REDMOTE CONNECTION WITH COMPUTER (WINDOWS) Next, you must establish a connection between the PC and the REDMOTE. 1. Connect a USB to mini-USB cable between the PC and the USB connector on the REDMOTE. If connecting for the first time, a RNDIS/Gadget driver is installed on the system. When the driver is installed, the battery charge indicator flashes on the REDMOTE.
R E D D S M C O P E R AT I O N G U I D E 08 TIMECODE, GENLOCK, MULTI-CAMERA SETUP This chapter describes timecode, genlock, and multi-camera operations such as 3D and array setup. TIMECODE Timecode is a numeric sequence based on SMPTE 12M that aids in the management and synchronization of footage and audio. Timecode is embedded in recorded RAW files as metadata and in HANC metadata provided by the HD-SDI monitor output.
R E D D S M C O P E R AT I O N G U I D E SET UP INTERNAL TIMECODE To set up and adjust timecode generated by the BRAIN, follow the instructions below. 1. Go to Menu > Settings > Project > Time Code. 2. Select the desired Time Code Display mode. 3. Set Time Code Source to User Provided. Source: User Provided 4. Use the additional controls to sync TOD timecode with the RTC or set manually. Alternatively, go to Menu > Media > Format Media... to set Edge timecode manually.
R E D D S M C O P E R AT I O N G U I D E SET UP EXTERNAL TIMECODE To set up and adjust timecode generated by an external device, follow the instructions below. 1. Connect the external timecode generator to the BRAIN using a 3BNC-to-00 LEMO Sync Cable. A. Connect the yellow BNC connector to the output on the timecode generator. B. Connect the 00B LEMO connector to the SYNC port on the BRAIN. 2. Go to Menu > Settings > Project > Time Code. 3. Select the desired Time Code Display mode. 4.
R E D D S M C O P E R AT I O N G U I D E GENLOCK Generator locking (genlock) is a tri-level signal used to synchronize video and audio systems. Genlock is based on SMPTE 296M and 274M. There are two (2) important genlock sync modes: Monitor Sync Sensor Sync NOTE: Genlock is ONLY possible between BRAINs that can achieve the same project time base and sensor frame rate. MONITOR SYNC Monitor Sync occurs when a genlock signal is provided that is compatible with the current monitor output frequency.
R E D D S M C O P E R AT I O N G U I D E SENSOR SYNC Sensor Sync is achieved when a genlock signal is provided that is compatible with the current monitor output frequency, project time base, and sensor frame rate. While operating in Sensor Sync, sensor timing is locked to the genlock signal.
R E D D S M C O P E R AT I O N G U I D E MASTER/SLAVE OPERATION This section describes operation in Master/Slave configuration and clip naming conventions for clips recorded on those cameras. Master/Slave is the most common configuration for Stereo/3D productions. When cameras are operated in Master/Slave configuration, you can perform the following operations: Power: Turn off the Master camera to turn off both cameras.
R E D D S M C O P E R AT I O N G U I D E C. For Target, select None. Slave Settings D. Go to Menu > Settings > Setup > Communication and select the Ethernet tab. E. Verify the Enable Camera to Camera check box is selected. The LAN indicator in the Lower Status Row illuminates green. NOTE: Cameras can also be set up in Master/Master configuration. To set as Master/Master, set Target to All on both cameras, allowing either camera to make changes and control record start/stop. COPYRIGHT © 2014 RED.
R E D D S M C O P E R AT I O N G U I D E SET REEL NUMBER, CAMERA ID, AND CAMERA POSITION To prepare media and slate settings for a Master/Slave or Stereo/3D production, follow the instructions below: 1. On both Master and Slave cameras, go to Menu > Media and select Format Media... 2. On both Master and Slave cameras, select the desired Reel No and Cam ID settings. NOTE: The Reel No and Cam ID settings on both BRAINs should match. 3.
R E D D S M C O P E R AT I O N G U I D E SET UP STEREO/3D CONFIGURATION This section describes basic procedures for connecting two (2) DSMC BRAINs in a Master/Slave configuration for 3D operation. NOTE: When providing the signals to a Stereo Image Processor (SiP) for verifying 3D alignment, set the HD-SDI monitor output on both cameras to have the same overlay configuration. NOTE: Genlock is ONLY possible between BRAINs that can achieve the same project time base and sensor frame rate.
R E D D S M C O P E R AT I O N G U I D E SET UP A CAMERA ARRAY You can sync more than two (2) cameras for applications and productions that require a camera array. To set up a camera array, you need a 1000Base-T gigabit Ethernet router. NOTE: Genlock is ONLY possible between BRAINs that can achieve the same project time base and sensor frame rate. NOTE: To operate a camera array setup from a PC or workstation, you need a terminal communications application such as Tera Term ® .
R E D D S M C O P E R AT I O N G U I D E SET UP MOTION CONTROL (MOCO) Motion Control, or “MoCo” for short, is a form of sensor synchronization used to automate precision camera movements required for special effects and difficult shots. Motion Control uses GPIO signals transmitted using the SYNC (GPI) and CTRL (GPO) ports on the camera BRAIN or a connected Pro I/O Module or 4K Broadcast Module. For more information GPIO connections, go to “Input/Output Connectors” on page 174.
R E D D S M C O P E R AT I O N G U I D E 5. On the Brain GPIO tab, set Camera Input to Sync In. MoCo BRAIN/GPIO Settings 6. On the Brain GPIO tab, set Camera Output to Sync Out. (Optional) Supply a pulse from the Motion Control device to sync the shutter to the rising edge of the sync input. For more information, refer to the Motion Control manufacturer’s instructions. REQUIRED CABLE 790-0154: 3BNC-to-00 LEMO Sync Cable (required per SYNC and CTRL port used) COPYRIGHT © 2014 RED.
R E D D S M C O P E R AT I O N G U I D E 09 UPGRADE DSMC FIRMWARE Your RED DSMC functionality may be upgraded by installing the latest firmware. Make a habit of frequently visiting www.red.com/downloads to check for new versions of camera firmware, updated operation guides, and post-production software. Your REDMOTE also requires a firmware upgrade. For more information on upgrading your REDMOTE, go to “Upgrade REDMOTE Firmware” on page 140.
R E D D S M C O P E R AT I O N G U I D E 8. Insert the SSD with the force_upgrade folder into your DSMC. 9. Turn on the DSMC. The upgrade runs automatically. During upgrade, the fans run at high speed and the PWR and REC LEDs flash green. After approximately 15 seconds, the LEDs stop flashing and the camera turns off. Nothing displays on the external monitors during the upgrade. 10. After the camera turns off, remove the SSD and wait 10 seconds. 11. Turn on the camera.
R E D D S M C O P E R AT I O N G U I D E 10 DSMC MAINTENANCE All RED products are designed for rugged durability, but precision instruments demand proper care. Follow the instructions in this chapter to clean, maintain, and store RED devices. WARNING: DO NOT rinse or immerse the DSMC ® or other accessories in water. Keep dry at all times. WARNING: DO NOT use soaps, detergents, ammonia, acetone, alkaline cleaners, abrasive cleaning compounds, or solvents.
R E D D S M C O P E R AT I O N G U I D E LCD AND EVF SCREENS This section explains how to clean screens on the following items: BOMB EVF RED PRO LCD RED Touch LCD DSMC Side Handle REDMOTE NOTE: This section describes only how to clean screens on specific RED devices, and not how to clean the entire device.
R E D D S M C O P E R AT I O N G U I D E 11 TROUBLESHOOT YOUR DSMC PERFORM A STRESS TEST Perform a stress test before important projects to ensure the reliability and stability of your gear. A stress test subjects your DSMC system and equipment to the increased stress of prolonged operation. If any components are developing issues, this test will help identify those problems before you have an equipment failure during a major shoot. 1. Configure your DSMC as desired. 2.
R E D D S M C O P E R AT I O N G U I D E CANNOT CONTROL CAMERA EXTERNALLY SYMPTOM The camera displays the message “For reliable external control over Ethernet your camera’s hardware may need to be upgraded. Please contact your Bomb Squad representative”. POTENTIAL RESOLUTIONS If you see this message, contact your Bomb Squad representative to have your hardware upgraded. You will not be able to control the camera externally until the hardware is upgraded.
R E D D S M C O P E R AT I O N G U I D E SCREEN FREEZES OR DOES NOT DISPLAY SYMPTOM The screen freezes or does not display. POTENTIAL RESOLUTION Perform a Hard Restore. A Hard Restore functions like a System Restore in that it changes all settings to the factory default values. To perform a Hard Restore, follow the instructions below: 1. Press and hold the PWR/REC button on the BRAIN for 20 seconds or until the fans turn at a high speed. 2. Release the PWR/REC button. The screen displays correctly.
R E D D S M C O P E R AT I O N G U I D E INCORRECT COLOR TEMPERATURE SYMPTOM The camera color temperature is off and the image looks warmer or cooler than normal. POTENTIAL RESOLUTION Perform an auto white-balance. For more information, go to “Color Temperature” on page 71. Perform a black shade calibration. For more information, go to “Calibrate” on page 98. If you have the DSMC Interchangeable OLPF system installed, verify that you have the correct OLPF selected in the OLPF menu.
R E D D S M C O P E R AT I O N G U I D E A TECHNICAL SPECIFICATIONS EPIC DRAGON EPIC DRAGON TECHNICAL SPECIFICATIONS SPECIFICATION DESCRIPTION Sensor 19 megapixels, RED DRAGON ™ Pixel Array 6144 (h) x 3160 (v) S/N Ratio 80 dB Dynamic Range 16.5+ stops Max Image Area 6144 (h) x 3160 (v) Lens Coverage 30.7mm (h) x 15.8mm (v) x 34.
R E D D S M C O P E R AT I O N G U I D E EPIC DRAGON TECHNICAL SPECIFICATIONS SPECIFICATION DESCRIPTION Operating Temperature Range 0˚C to 40˚C (32˚F to 104˚F) Storage Temperature Range –20˚C to 50˚C (–4˚F to 122˚F) COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E SCARLET DRAGON SCARLET DRAGON TECHNICAL SPECIFICATIONS SPECIFICATION DESCRIPTION Sensor 19 megapixels, RED DRAGON ™ Pixel Array 6144 (h) x 3160 (v) S/N Ratio 80 dB Dynamic Range 16.5+ stops Max Image Area 6144 (h) x 3160 (v) Lens Coverage 30.7mm (h) x 15.8mm (v) x 34.5 mm (d) Max Depth of Field Equivalent to S35mm (Motion)/APS-H (Still) lenses Acquisition Formats 1 6K 5K 4K 3K 2K Project Frame Rates 23.98, 24, 25, 29.97, 47.96, 48, 50, 59.
R E D D S M C O P E R AT I O N G U I D E SCARLET DRAGON TECHNICAL SPECIFICATIONS SPECIFICATION DESCRIPTION Operating Temperature Range 0˚C to 40˚C (32˚F to 104˚F) Storage Temperature Range –20˚C to 50˚C (–4˚F to 122˚F) 1. Go to “SCARLET DRAGON Formats” on page 82 for a full list. 2. To see all of the maximum available REDCODE values, see the DSMC Media Operation Guide at www.red.com/downloads. COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E EPIC MYSTERIUM-X EPIC MYSTERIUM-X TECHNICAL SPECIFICATIONS SPECIFICATION DESCRIPTION Sensor 14 megapixels, MYSTERIUM-X ™ Pixel Array 5120 (h) x 2700 (v) S/N Ratio 66 dB Dynamic Range 13.5 stops, up to 18 stops with HDRx ™ Max Image Area 5120 (h) x 2700 (v) Lens Coverage 27.7mm (h) x 14.6mm (v) x 31.
R E D D S M C O P E R AT I O N G U I D E SCARLET MYSTERIUM-X SCARLET MYSTERIUM-X TECHNICAL SPECIFICATIONS SPECIFICATION DESCRIPTION Sensor 14 megapixels MYSTERIUM-X ™ Pixel Array 5120 (h) x 2700 (v) S/N Ratio 66 dB Dynamic Range 13.5 stops, up to 18 stops with HDRx ™ On 6 FPS with 5K Full Frame and HDRx ™ On 15 FPS with 4K HD and HDRx ™ On Max Image Area 5120 (h) x 2700 (v) Lens Coverage 27.7mm (h) x 14.6mm (v) = 31.
R E D D S M C O P E R AT I O N G U I D E BRAIN DIMENSIONS NOTE: Dimensions are shown in mm. EPIC BRAIN DIMENSIONS FRONT VIEW COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E SIDE VIEW COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E TOP VIEW COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E BOTTOM VIEW COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E BACK VIEW COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E B INPUT/OUTPUT CONNECTORS 1 2 3 4 5 6 7 8 9 DSMC Connectors (Rear) # CONNECTOR CONNECTOR TYPE FOR MORE INFORMATION, GO TO... 1 REDMOTE Dock 8-point POGO “REDMOTE Operation” on page 133 2 Module Power SEARAY “Power Inputs” on page 31 3 HD-SDI BNC “HD-SDI Out” on page 175 4 HDMI HDMI “HDMI Out” on page 176 5 Headphone Jack 3.
R E D D S M C O P E R AT I O N G U I D E HD-SDI OUT A standard 75 ohm BNC connector provides the following output: Broadcast specification HD-SDI video output (default mode is Clean) Two (2) channels of embedded audio Time of Day and Edge timecode Record Tally flag Clip name information (as SMPTE RP-188 VITC2 HANC metadata) For more information, go to “Monitor” on page 61.
R E D D S M C O P E R AT I O N G U I D E HDMI OUT A standard HDMI connector provides the following output: High-definition video output (default mode is Overlay) Two (2) channels of embedded audio The HDMI output provides the formats described in the table below: HDMI OUTPUT FORMATS 1 VIDEO FEED 2 FREQUENCY (HZ) 720p 24.00, 25.00, 30.00, 50.00, 60.00 1080p 24.00, 25.00, 30.00, 50.00, 60.00 1200p 60.00 1. Ensure you select a frequency supported by your monitor. 2.
R E D D S M C O P E R AT I O N G U I D E SYNC (VIDEO SYNC IN) The 4-pin 00B LEMO SYNC connector accepts timecode, genlock, and General Purpose Input (GPI) signals. 1 4 2 3 SYNC (Video Sync) Connector 4-PIN 00B LEMO SYNC CONNECTOR 1 PIN SIGNAL DESCRIPTION 1 GROUND Common Ground 2 SS/GPI Shutter Sync/GPI Trigger Input 3 TIMECODE SMPTE unbalanced timecode Input 4 GENLOCK RS170A Tri-Level Sync Input 1. Mating connector: FGG.00.304.
R E D D S M C O P E R AT I O N G U I D E COMPATIBLE CABLES 790-0154: 3BNC-to-00 LEMO Sync Cable ‒ ‒ White BNC: Shutter Sync/GPI ‒ ‒ Yellow BNC: SMPTE Timecode ‒ ‒ Green BNC: RS170A Genlock 790-0187: 4-Pin 00 LEMO-to-Flying Lead 790-0415: RED Start/Stop Cable (14-Pin LEMO to SYNC, CTRL, BNC) 790-0428: RED Start/Stop Cable (14-Pin to 00 SYNC) CTRL (RS232 CONTROL) The 4-pin 00B LEMO CTRL connector supports RS232 remote control for 3D camera communication and thirdparty metadata ingest applic
R E D D S M C O P E R AT I O N G U I D E GIG-E (ETHERNET) The GIG-E 9-pin 0B LEMO connector provides a 1000BASE-T (IEEE 802.3ab) gigabit Ethernet connection for remote camera setup, master/slave camera communication, and external metadata ingest. Since the GIG-E connector does not support slower speeds (10BASE-T and 100BASE-T), ensure that any device you connect to supports 1000BASE-T.
R E D D S M C O P E R AT I O N G U I D E DC IN (POWER INPUT) The 6-pin 1B LEMO connector accepts DC input power from 11.5 V DC to 17 V DC. A built-in power conditioner protects against reverse-polarity connections, electrostatic discharge (ESD), undervoltage, overvoltage, and overcurrent. WARNING: Both pairs of +VBATT and GROUND pins must be wired. Using a third-party power cable that wires only one (1) pair of +VBATT and GROUND pins may damage the power supply or the DSMC.
R E D D S M C O P E R AT I O N G U I D E MIC-1, MIC-2 (MICROPHONE AUDIO) The two (2) 3.5mm microphone jacks are microphone level analog audio inputs. Each jack has 2.4K ohm of nominal impedance. For more information, go to “Record and Monitor Audio” on page 126.
R E D D S M C O P E R AT I O N G U I D E C LENS MOUNTS AND LENSES LENS MOUNTS This section describes DSMC lens mounts. DSMC mounts may be configured with 19mm rods to accommodate most cinematography lenses, matte boxes, and follow focus systems. DSMC MOTION MOUNTS The DSMC RED Motion Mount is a revolutionary and adjustable lens mount system for your DSMC.
R E D D S M C O P E R AT I O N G U I D E REMOVE LENS MOUNTS NOTE: You can change lens mounts in the field. However, RED recommends that you change lens mounts only in dust-free environment. REQUIRED TOOL: T20 Torx ® driver 1. Turn off the DSMC. 2. Attach the DSMC to a stable platform or position the DSMC on a clean and level work surface so that the lens mount screws are accessible. 3.
R E D D S M C O P E R AT I O N G U I D E INSTALL LENS MOUNTS NOTE: You can change lens mounts in the field. However, RED recommends that you change lens mounts only in dust-free environment. REQUIRED TOOL: T20 Torx driver 1. Ensure that the DSMC is turned off and remove any accessories or cables that may interfere with installation. 2.
R E D D S M C O P E R AT I O N G U I D E LENSES This section describes lenses and lens operations for the DSMC system. WARNING: All lenses are hot swappable. However, lens mounts are NOT HOT SWAPPABLE, meaning you cannot remove or install lens mounts while the camera is turned on. Before installing or removing lens mounts, you MUST turn off the camera. Failure to do so may result in damage to the lens mounts or DSMC that will not be covered under warranty.
R E D D S M C O P E R AT I O N G U I D E POSITIVE LOCK (PL) LENSES This section describes the appropriate method for attaching and detaching PL lenses. For more information, refer to the original manufacturer’s instructions. WARNING: ALWAYS protect your equipment, when it is not in use, by replacing lens caps and mount caps. ATTACH PL LENSES 1. Rotate the lens mount frame counter-clockwise to release the DSMC mount cap. 2. Remove the rear lens cap and the DSMC mount cap. 3.
R E D D S M C O P E R AT I O N G U I D E NIKON F-MOUNT LENSES This section describes the appropriate method for attaching and detaching Nikon F-Mount lenses. For more information, refer to the original manufacturer’s instructions. WARNING: ALWAYS protect your equipment, when it is not in use, by replacing lens caps and mount caps. ATTACH NIKON F-MOUNT LENSES 1. Rotate the secondary locking clamp counter-clockwise to disengage. 2.
R E D D S M C O P E R AT I O N G U I D E DSMC CANON MOUNT SUPPORTED LENSES The DSMC Canon Mount and DSMC Canon Motion Mount electronically support the following lenses: COMPATIBLE LENS TYPE FOCAL LENGTH Canon EF Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon C
R E D D S M C O P E R AT I O N G U I D E COMPATIBLE LENS TYPE FOCAL LENGTH Canon EF Canon Canon Canon Canon Canon Canon Canon Canon Canon Canon EF EF EF EF EF EF EF EF EF EF Canon EF-S Canon Canon Canon Canon Canon EF-S EF-S EF-S EF-S EF-S Sigma Sigma Sigma Sigma Sigma Sigma Sigma Sigma Sigma Sigma 10-20mm f/3.5 EX DC HSM 17-70mm f/2.8-4 DC Macro OS HSM 18-35mm DC HSM 20mm f/1.8 EX DG ASP RF 24mm f/1.8 EX DG ASP Macro AF 24-70mm f/2.8 IF EX DG HSM 28mm f/1.8 EX DG ASP Macro AF 50mm f/1.
R E D D S M C O P E R AT I O N G U I D E DSMC NIKON MOUNT SUPPORTED LENSES The DSMC Nikon Mount electronically supports the following lenses: COMPATIBLE LENS TYPE FOCAL LENGTH Nikkor AF AF Nikkor 50mm f/1.8D AF DX Fisheye-Nikkor 10.5mm f/2.8G ED AF Fisheye-Nikkor 16mm f/2.8D 1 Nikkor AF-S AF-S AF-S AF-S AF-S AF-S AF-S AF-S AF-S AF-S AF-S AF-S AF-S AF-S AF-S Sigma Sigma Sigma Sigma Sigma Sigma APO Sigma APO 120-300mm f/2.8 EX DG OS HSM Tamron Tamron SP 24-70mm f2.
R E D D S M C O P E R AT I O N G U I D E D DEFAULT KEY FUNCTIONS CAMERA BRAIN KEY FUNCTION KEY FUNCTION Record Half Press Key Disabled Record Half Release Key Disabled Record Full Press Record: Toggle Record Full Release Key Disabled GPI In High Record: Start GPI In Low Record: Stop SIDE SSD MODULE KEY FUNCTION KEY FUNCTION Record Full Press Record: Toggle Record Full Release Key Disabled Record Half Press AF: Start Record Half Release Key Disabled User 1 Press Key Disabled
R E D D S M C O P E R AT I O N G U I D E UI SOFT KEYS KEY FUNCTION KEY FUNCTION UI Softkey A Press Key Disabled UI Softkey 1 Press Key Disabled UI Softkey B Press Key Disabled UI Softkey 2 Press Key Disabled UI Softkey C Press Key Disabled UI Softkey 3 Press Key Disabled UI Softkey D Press Key Disabled UI Softkey 4 Press Key Disabled DSMC SIDE HANDLE KEY FUNCTION KEY FUNCTION User A Press AF Mode: Cycle User A Release Key Disabled User B Press WB: Auto Calc User B Release Key
R E D D S M C O P E R AT I O N G U I D E REDMOTE KEY FUNCTION KEY FUNCTION User A Press AF Mode: Cycle User A Release Key Disabled User B Press RAW Check: Toggle User B Release Key Disabled User C Press Magnify: Toggle User C Release Key Disabled User D Press Exposure Check: Toggle User D Release Key Disabled Still Select Focus Mode: Still Movie Select Focus Mode: Motion Record Full Press Record: Toggle Record Full Release Key Disabled Record Half Press AF: Start Record Half Re
R E D D S M C O P E R AT I O N G U I D E PRO I/O GPIO KEY FUNCTION KEY FUNCTION GPI A High Key Disabled GPI A Low Record: Toggle GPI B High Key Disabled GPI B Low Record: Toggle SW 1 High Key Disabled SW 1 Low Go to: Playback SW 2 High Key Disabled SW 2 Low Record: Toggle COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E E MENU MAP See the menu map on the following page. The menu map is applicable to the following cameras, except as noted in the this guide: EPIC-M RED DRAGON™ (CARBON FIBER) EPIC-M RED DRAGON EPIC-X RED DRAGON SCARLET DRAGON EPIC-M MYSTERIUM-X EPIC-X MYSTERIUM-X SCARLET-X MYSTERIUM-X EPIC-M MONOCHROME EPIC-X MONOCHROME EPIC-M RED DRAGON MONOCHROME COPYRIGHT © 2014 RED.COM, INC 955-0020_V5.
R E D D S M C O P E R AT I O N G U I D E MENU SETTINGS MEDIA } Eject Media PLAYBACK } Playback Screen } Format Media POWER HDR FOCUS } Power In } HDRx Toggle } Mode } Power Save } Stops } Rack } Utils...
RED DIGITAL CINEMA COPYRIGHT© 2014 RED.COM, INC. All trademarks, trade names, logos, icons, images, written material, code and product names used in association with the accompanying product are the copyrights, trademarks or other intellectual property owned and controlled exclusively by RED.COM, INC.
