565 Trailer Sprayer Parts and Operator’s Manual
565 Trailer Sprayer Patent Pending TO THE OWNER Congratulations on your selection of a Redball® Model 565 Trailer Sprayer. Redball® Sprayers have earned a reputation of providing a durable sprayer throughout the U.S. and Canada. Redball® Sprayers have been designed to provide many years of profitable and dependable service. To assure maximum performance of your sprayer, it is mandatory that you thoroughly study the operator's manual and follow its recommendations.
565 Trailer Sprayer Table of Contents TABLE OF CONTENTS Safety Instructions Safety First Safety Instructions for Operation Safety Decal Placement Section A 1 2 5 Operation Instructions Section B Inspect Unit 1 System Overview 1 Hitch 2 Liquid Tanks & Cradle Frame 2 Sprayboom & Nozzles 2 Liquid Pumping & Plumbing 3 Centrifugal Pump 4 Hydraulically Driven Centrifugal Pump 4 PTO Driven Centrifugal Pump 5 Fill Solution Tank 5 Fill Solution Tank, Utilizing Eductor (Optional) 6 Fill Solution Tank, Tank Agitatio
565 Trailer Sprayer Table of Contents TABLE OF CONTENTS Connection & Startup Connection Hitch Visual Inspection Axles Fixed Row Crop Width Axles Tire Weight Capacities Hydraulics Hydraulically Driven Pumps Centrifugal Pump Hydraulic SprayBoom Control Solution Spray Control System Light System Seven Pin Connector Foam Marker Section C 1 1 2 2 2 3 5 Storage Storage Sprayer Winterization Section D 1 2 Maintenance, Service & Troubleshooting Liquid Tank, Frame and Plumbing Hydraulics Electrical & Control Sys
65 Trailer Sprayer - Safety Instructions Section A 3-07
565 Trailer Sprayer - Safety Instructions Section A Safety First Accidents can be prevented by recognizing the causes or hazards before an accident occurs..... and doing something about them. Regardless of the care used in the design and construction of this equipment, there are some areas that cannot be completely safeguarded without interfering with the accessibility and efficiency of operation. THIS MESSAGE ALERT SYMBOL IDENTIFIES IMPORTANT MESSAGES IN THIS MANUAL.
565 Trailer Sprayer - Safety Instructions Section A Safety Instructions for Operation 1. DO NOT ALLOW ANYONE TO OPERATE THIS REDBALL SPRAYER UNTIL HE OR SHE HAS READ THIS MANUAL AND IS COMPLETELY FAMILIAR WITH ALL SAFETY AND OPERATION PROCEDURES. WARNING Observe the IMPORTANT SAFETY INSTRUCTIONS listed below at all times! THE BEST KIND OF SAFETY IS A CAREFUL OPERATOR CAUTION Always wear protective clothing, goggles, respirator and gloves when handling chemicals.
565 Trailer Sprayer - Safety Instructions Section A 4. People who are allergic to any of the chemicals used must never be allowed in or near the sprayer. 5. Always park the sprayer on a level surface, and lock the tractor brakes,or block the tires, before making adjustments or repairs. 6. Before operating this equipment, thoroughly inspect the unit to insure it is in good working order. 7. Do not operate this unit if any defect or malfunction exists.
565 Trailer Sprayer - Safety Instructions Section A 11. Do not replace components or parts with those other than genuine Redball® Factory Service Parts. To do so may reduce the effectiveness of safety features or decrease the accuracy of the unit. 12. Read the Operator Instructions section of this manual for further necessary information relating to the safe operation of the applicator.
565 Trailer Sprayer - Safety Instructions Section A SAFETY DECALS ON A REDBALL® 565 TRAILER SPRAYER P/N 002439 2 1 P/N 002438 P/N 004772 3 4 P/N 004773 P/N 004774 5 P/N 004775 6 7 P/N 004776 8 9 P/N 30000000 5 Section A P/N 30000001 3-07
565 Trailer Sprayer - Safety Instructions Section A SAFETY DECAL PLACEMENT Ref-016805B 6 Section A 3-07
565 Trailer Sprayer - Safety Instructions Section A SAFETY DECALS ON A REDBALL® 565 TRAILER SPRAYER Boom Decals 1 3 P/N 002439 P/N 005499 2 5 4 7 Section A 3-07
565 Trailer Sprayer - Safety Instructions Section A SAFETY DECAL PLACEMENT 015890A 8 Section A 3-07
565 Trailer Sprayer - Safety Instructions Section A NOTES: 9 Section A 2-07
3-07
565 Trailer Sprayer - Operation Instructions Section B Inspect Unit IMPORTANT CAUTION Check machine thoroughly for screws, bolts, fittings, etc., which may have come loose during transport or operation. Prior to loading with chemical, the operator needs to test the sprayer with water only to ensure the system is intact prior to putting chemical into the system. Test to verify application at the desired rate and all components work correctly.
565 Trailer Sprayer - Operation Instructions Section B Hitch Verify hitch is correctly attached to the tractor. See Section C for connection procedures. IMPORTANT 1.) Towing tractor must weigh 12,000 pounds to ensure adequate stopping ability. Refer to your tractor manufacturer rating capabilities. 2.) Do not tow sprayer over 20 MPH. Clevis Hitch Safety Chain Main Product Liquid Tank & Steel Saddle A polyethylene tank is supported by a structural steel saddle. The tank is strapped in the saddle.
565 Trailer Sprayer - Operation Instructions Section B Main Line Filter Liquid Pumping & Plumbing Regulating Valve Solution Quick Fill Valve Solution Tank Main Valve The liquid system begins with a suction line supplying a centrifugal pump. This pump is powered via tractor hydraulics or PTO shaft and provides flow to the sprayer.
565 Trailer Sprayer - Operation Instructions Section B Centrifugal Pump Pump operation is very important. The following must be followed when operating a centrifugal pump. Proper pump operation will make your system operate with minimal maintenance and down time. Failure to follow the manufacturer’s pump operation instructions will void the pump warranty. The pump must never be run in a non-flooded condition.
565 Trailer Sprayer - Operation Instructions Section B There are two basic rules to follow when operating a hydraulically driven centrifugal pump: 1. Never run the pump in a “non-flooded” condition. 2. Always have the correct oil flow to the pump motor. Always read and follow the pump manufacturer’s operational instructions. IMPORTANT Turn off a hydraulically driven centrifugal pump using the “float” posi- IMPORTANT tion of the tractor’s hydraulic valve.
565 Trailer Sprayer - Operation Instructions Section B Fill Solution Tank, Utilizing Optional Eductor: Load the solution tank using the optional eductor via the following steps: 1. Close all valves. 2. Remove solution quick fill cap & connect load hose. 3. Open solution quick fill valve and solution tank main valve. 4. Open valve on loading reservoir (i.e. nurse tank) 5. Fill eductor with desired amount of chemical to be pulled into the solution tank. CLOSE Eductor Lid. 6. Start the remote transfer pump. 7.
565 Trailer Sprayer - Operation Instructions Section B Solution Quick Fill Valve Solution Tank Main Valve Quick Fill Cap Fill Solution Tank, With Tank Agitation: Loading of the solution tank, using tank agitation, is accomplished via the following steps: 1. Close all valves. 2. Remove solution quick fill cap & connect load hose. 3. Open solution quick fill valve and the solution tank main valve. 4. Open valve on loading reservoir (i.e. nurse tank). 5. Start the remote transfer pump. 6.
565 Trailer Sprayer - Operation Instructions Section B Rinse Solution Tank Using the clean water rinse tank system (optional on 665), rinsing the solution tank with clean water is accomplished via the following steps: IMPORTANT Only you, the operator can determine the length of time required to completely rinse all chemical residue from the sprayer tanks and plumbing systems. Close all valves. Open the clean water rinse tank valve. Open the rinse ball valve. Power ON the liquid pump of the sprayer.
565 Trailer Sprayer - Operation Instructions Section B Rinse Sprayboom Plumbing Using the clean water rinse tank system (optional on 665), rinse the sprayboom plumbing with clean water via the following steps: Sprayboom Section Valves IMPORTANT Only you, the operator can determine the length of time required to completely rinse all chemical residue from the sprayer tanks and plumbing systems. Rinse Ball Valve 1. Close all valves. 2. Open the clean water rinse tank valve. 3.
565 Trailer Sprayer - Operation Instructions Section B Spraying Spraying is accomplished via the following steps: 1. Close all valves. 2. Open the the solution tank main valve. 3. Setup control system. (Setup and operation of the control system is covered in the manual provided by the controller manufacturer.) 4. Power ON the liquid pump of the trailer sprayer. 5. Open desired spray boom section valves. 6. Perform spraying according to the control system provided. 7.
565 Trailer Sprayer - Operation Instructions Section B Solution Quick Fill Valve Solution Tank Main Valve Quick Fill Cap IMPORTANT Unload Three processes can be utilized for unloading of liquid remaining in the solution tank. Option A: Spray remaining liquid out the sprayboom plumbing. Option B: Remove Quick Fill Cap, open the solution quick fill valve and the solution tank valves and let remaining liquid drain via gravity from the solution tank. Option C: Remove plug in main solution tank.
565 Trailer Sprayer - Operation Instructions Section B Solution Spray Control System (Optional) See the controller manufacturer’s manual for operation instructions. Light and Marking System The light system on the sprayer works with the tractor’s light system. Amber lights flash in unison with the tractor amber flashing lights. If a turn is not being signaled, both amber lights flash.
565 Trailer Sprayer - Operation Instructions Section B NOTES: 13 Section B 3-07
565 Trailer Sprayer - Connection & Startup Section C 3-07
565 Trailer Sprayer - Connection & Startup Section C Connection Hitch Redball® provides a clevis style hitch. Connect the sprayer to the tractor according to the tractor manufacturer’s instruction via the clevis. Clevis Hitch Safety Chain Hook Latch Safety Chain Hook WARNING Safety Chain Make certain that the safety chain is securely fastened to both the tractor and the sprayer. The tractor end must be attached according to the tractor manufacturer’s instructions.
565 Trailer Sprayer - Connection & Startup Section C Visual Inspection All steps of the inspection should be performed with the tractor engine turned off and the brakes correctly set, or the tires blocked. A visual inspection of the entire sprayer should be made.
565 Trailer Sprayer - Connection & Startup Section C Tire Weight Capacities - 20 MPH NOTE Use this chart as a guide to determine the maximum amount of various solutions your sprayer tires are rated for. 8 MPH is the service or field speed for this sprayer. 20 MPH is used here to demonstrate a speed used to transport the sprayer, NOT as a service or field speed. Only the operator can determine the maximum safe operating speed of the sprayer.
565 Trailer Sprayer - Connection & Startup Section C Tire Weight Capacities - 8 MPH NOTE Use this chart as a guide to determine the maximum amount of various solutions your sprayer tires are rated for. 8 MPH is the service or field speed for this sprayer. 20 MPH is used here to demonstrate a speed used to transport the sprayer, NOT as a service or field speed. Only the operator can determine the maximum safe operating speed of the sprayer.
565 Trailer Sprayer - Connection & Startup Section C Hydraulics Tractor Hydraulic System Pressure The hydraulic system on the Redball® Model 565 Trailer Sprayer requires from the tractor's hydraulic system a pressure of at least 2200 PSI. A system pressure less than this may not provide the force necessary for boom functions or pump output. If you have difficulty running the pump and/or boom functions at the same time, check your tractor’s hydraulic pressure. Recommended pressure is 2500 PSI.
565 Trailer Sprayer - Connection & Startup Section C Hydraulic SprayBoom Control In reference to the hydraulic control functions, the hydraulic hoses that connect to the tractor have been marked for your convenience to indicate what function a particular hose serves. See the identification method to the right. Direct Tractor Hookup (Option on 565) Quick couplers should be connected to the tractor. Make certain to correctly connect the pressure and return line hoses to the tractor hydraulic ports.
565 Trailer Sprayer - Connection & Startup Section C It has a set of hoses leading from the hydraulic valve bank to the tractor hydraulics connecting with a pair of hydraulic hoses with quick couplers. The operator needs to actuate the tractor hydraulic controls for the valve the hydraulic controller connects first, then actuate the toggle switch on the hydraulic controller's switch box for the function needed.
565 Trailer Sprayer - Connection & Startup Section C Calibration of the radar or speed sensor is necessary to ensure accurate readings. Calibrate the speed sensor or radar according to the manufacturer’s instructions or the instructions provided with the solution controller. Even with a radar or speed sensor, calibration of the spray output is necessary to assure correct application. Follow the control manufacturer’s guidelines for this calibration.
565 Trailer Sprayer - Connection & Startup Section C NOTES: 9 Section C 3-07
565 Trailer Sprayer - Storage Section D 3-07
565 Trailer Sprayer - Storage Section D Storage When storing the sprayer for longer periods of time, the following procedures must be followed to lessen the chance of rust and corrosion on the unit. It may be easier to perform functions 1 - 5 while the unit is connected to the tractor. This will allow for pumping and spray rinsing power. CAUTION Block and support the trailer sprayer when working on a unit that has been removed from the tractor 1. Make certain tank is completely empty. 2.
565 Trailer Sprayer - Storage Section D Sprayer Winterization Proper winterization is an important step in extending the life of your sprayer investment and preparing it for operation next season. The following steps are a guideline to assist in the winterization of your sprayer. DANGER All chemical contaminated rinse material must be collected and disposed of according to product label instructions and in accordance with all local, state, and federal laws.
565 Trailer Sprayer - Storage Section D 3. Begin the process of protecting the plumbing with the addition of RV antifreeze. a. Close all of the valves in the system, including the solution tank valve located between the tank and the pump. b. Add a minimum of 10 gallons of RV antifreeze to the rinse tank. c. Open the rinse tank valve to let the antifreeze solution flow from the rinse tank to the pump. Make sure that the pump is charged with solution.
565 Trailer Sprayer - Storage Section D c. One at a time, turn on each of the boom sections to allow the antifreeze solution to be pumped through the controls and the boom valves. Run enough solution that the antifreeze begins to spray out the boom sections. d. Turn off the solution pump. Cycle the spray boom valves open and closed to allow the antifreeze solution that is trapped in the hoses to drain back. Remove the strainers, clean and reinstall. 5.
565 Trailer Sprayer - Storage Section D NOTES: 5 Section D 3-07
565 Trailer Sprayer - Maintenance, Service & Troubleshooting Section E 3-07
565 Trailer Sprayer - Maintenance, Service & Troubleshooting Section E IMPORTANT Proper maintenance of the Sprayer and the tractor is critical for peak performance, reliability and accuracy of this system. The following is a guideline of the type of maintenance and servicing that should be performed on this unit. Your environment and uses may require additional maintenance and service beyond this list to assure a reliable and safe unit.
565 Trailer Sprayer - Maintenance, Service & Troubleshooting Section E Hydraulics 1. Inspect cylinder shafts for corrosion or damage. Repair or replace shaft to avoid hydraulic leaks or cylinder failure. 2. Inspect hydraulic hoses. Replace any hose that shows signs of wear or damage. 3. Removing hydraulic hoses for any reason requires that you plumb them back to their original position. Failure to do this may result in incorrect operation and may damage the sprayer.
565 Trailer Sprayer - Maintenance, Service & Troubleshooting Section E Lubrication 1. Always lubricate the 565 Trailer Sprayer before bringing the machine to the field. 2. Stop the tractor, set the parking brake and turn off the engine before performing maintenance or lubricating the machine. 3. Grease fittings every 10 hours of use. See drawing below. 4. Clean grease fittings before lubricating. 5. If grease fittings are missing or damaged, replace the fittings to ensure lubrication. 6.
565 Trailer Sprayer - Maintenance, Service & Troubleshooting Section E NOTE Failure to check and maintain the proper lug nut torque could result in elongation of rim and/or broken lug-bolts. We recommend checking lug nut torque at regular maintenance intervals to ensure proper wheel tightness on your Redball® 565 Trailer Sprayer. Wheel Lug Nut Torque When receiving your sprayer or replacing a tire, follow these steps for ensuring proper lug-nut torque: NOTE DO NOT lubricate threads. 1.
565 Trailer Sprayer - Maintenance, Service & Troubleshooting Section E Bolt Torque Data The chart provided contains information concerning standard hardware used on this machine. It is recommended that all fasteners be tightened to the torque values specified.The grade of the bolt is identified by the markings on the head of the bolt . GENERAL BOLT TORQUE DATA IN FT./LB.
565 Trailer Sprayer - Maintenance, Service & Troubleshooting Section E SYMPTOM Loss of hydraulic fluid due to leakage PROBABLE CAUSE CORRECTIVE ACTION Fittings and tubes leaking Tighten loose fittings and replace worn hoses or cracked tubing. Leakage between flange and housing Repair or replace Pump not primed Check vent line for proper installation. Clean if necessary.
565 Trailer Sprayer - Maintenance, Service & Troubleshooting Section E NOTES: 7 Section E 3-07
565 Trailer Sprayer - Parts & Schematics Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Ref-016818B Decal Placement 1 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Decal Placement Item# Part # Description Quantity 1 2 3 4 5 6 007527 010879 012293Y 9030-0021 001 013046 Decal; Tighten Straps Decal; Valve Chart Decal; 565 Black/Yellow Decal; Black & Yellow 2 x 13” Redball Decal; FEMA Decal; Made In USA 1 1 2 2 1 1 2 Section F 3-07
5 Trailer Sprayer - Parts & Schematics Section F 3 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Lighting and Marking Placement Item# Part # Description Quantity 1 001186 Bracket; Light Mounting 2 2 004560 Lamp; Turn/Tail, Red 2 3 004561 Lamp; Flash/Warn Tail, Amber 2 4 006978 Turn Signal Module II 1 5 007179 Harness; Tractor/Implement 1 6 007206 Harness; Light - 3 PT LG Equip 1 7 17-5910 Reflector; Amber 2” x 9” Night 4 8 17-5915 Reflector; Red 2” x 9” Night 2 9 17-5920 Reflector; Orange 2” x 9” Da
565 Trailer Sprayer - Parts & Schematics Section F 5 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: 565 Frame Assembly Item# Part # 9 016660 10* Description Quantity Brace; Frame 2 AC313003 Rail; Tongue L.H. Weldment 1 11* AC313193 Hitch; Weldment - 750 1 12* AC313296 Frame Mount Weldment 1 13 AC313309 Stand Mount Weldment L.H. 1 14 AC313310 Stand Mount Weldment R.H.
565 Trailer Sprayer - Parts & Schematics Section F Description: 565 Tank & Sprayer Front Assembly Tank/Handrail/Ladder 7 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: 565 Tank & Sprayer Front Assembly Tank/Handrail/Ladder Item# Part # 6 AC217944 7* 016062 8 Description Quantity Weldment; Ladder Mount 1 Weldment; Cradle 565 1 AC313519 Weldment; Ladder 1 9 AC607449 Jack; Swivel, Side Wind, 2000# 1 10 AC607451 Snap Ring; Part of AC607449 1 11 NW60012 Rim for 16” Lid 1 12 SFPI-10ST Screw; 1”x #10 FH PH Self Tap, SS 8 13 0254-1035 Rope; 1/8” Nylon 14 NW60011 Lid; 16” with Ai
565 Trailer Sprayer - Parts & Schematics Section F Description: Ref-016752C Vertical Mast Assembly 9 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Vertical Mast Assembly Item# Part # Description 1 016346 Weldment; Mast Tube Front 2 2 AC313308 Channel Upper Support 1 3 AC313384 Lower Lift Weldment 1 4 AC217453 Plate Side 4 5 AC313298 Tube Slider 2 6 BH-050-350-5 Bolt, 1/2” x 3 1/2” Hex. GR.
565 Trailer Sprayer - Parts & Schematics Section F 11 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: 60 Ft. Boom Carriage & Suspension Item# Part # Description Quantity 1 014896 Weldment; Boom Carriage 1 2 014906 Bushing; 1.06 OD Stepped x .650 ID 2 3 014908 Flat; .375 x 2.00 x 5.25 w/holes 4 4 014911 Spring; 5.25 OD x 12.75 Lg, .56 Wire 2 5 014919 Washer, Belleville; 7/8 ID x 1 3/4 OD 14 Ga.
565 Trailer Sprayer - Parts & Schematics Section F Description: Ref-016395A Center Boom Assembly 13 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Center Boom Assembly Item# Part # Description 1 014855 Weldment; Boom Center 1 2 014871 Weldment; Pin 10.125 w/Threads 2 3 014937 Slide; UHMW .625 x 1.75 x 11.00 w/HOLS 4 4 014947 Weldment; Wing Tilt Adj Rod 2 5 014951 Round, CR; .625 x 2.625 w/HOLS 2 6 015812 Screw, Torx; 1/4-20 x 1.00 12 7 FW-087 Flatwasher; 7/8” 4 8 LN-075-NI Locknut; 3/4” Nylon Insert 2 9 MB-062-100-14 Bushing, Machine 5/8 x 1.
565 Trailer Sprayer - Parts & Schematics Section F Description: Pivot to Primary 15 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Pivot to Primary Item# Part # Description Quantity 1* 014880 Weldment; Boom Pivot LH 1 2* 015000 Weldment; Boom Primary LH 150” 1 3 014878 Weldment; Boom Pivot RH 1 4 014909 Turnbuckle, Closed Body, 5/8” 4 5 014910 CYL; U-60 Boom Fold (1.50” x 11.62”) 2 6 014936 Slide; UHMW .218 x 1.50 x 4.0 w/HOLS 4 7 014944 Weldment, Pivot Pin; 1.00 Pin w/Formed 2 8 014950 Urethane; 90A .63 x 1.88 x 3.
565 Trailer Sprayer - Parts & Schematics Section F Description: Secondary Boom Fold 17 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Secondary Boom Fold Item# Part # Description Quantity 1* 015000 Weldment; Boom Primary LH 150” 1 2 008053 Connecting Link; #50 4 3 014933 Assembly; Cable 191” with LRG Spring 2 4 014934 Assembly; Cable 114” with SM Spring 2 5 014964 Urethane, Bumper; 2.00 x 1.60 with 3/8” THRD 2 6 014979 Flat; .625 x 2.00 FRMD 2 7 014980 Weldment; Boom Sec., RH 51” 1 8 014985 Weldment; Sprocket w/.
565 Trailer Sprayer - Parts & Schematics Section F Description: Breakaway Assembly 19 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Breakaway Assembly Item# Part # Description Quantity 1* 014917 Weldment; Boom Section, LH 51” 1 2 014958 Weldment; Breakaway 98” 2 3 014980 Weldment; Boom Section, RH 51” 1 4 015797 Weldment; Lower Breakaway Clutch 2 5 015803 Weldment; Upper Breakaway Clutch 2 6 015804 Pin; Threaded Breakaway Shaft 2 7 015806 Spring; .375 Wire 2” DIA x 4” LG 2 8 015807 Spring Cup; 2.219 ID x .
565 Trailer Sprayer - Parts & Schematics Section F Description: 565 Hydraulic Breakdown 21 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Hydraulic Multiplier Valve Breakdown Item# Part # Description Quantity 1 270-058 Block M10937-1 1510/BP 1 2 272-019 Coupling Fasse ISO Poppet Male Tip 2 3 272-018 Coupling Fasse ISO Poppet Female 4 4 210-180 Fitting Fasse Orbit Eccentric 2 5 230-095 Cap #3 2 6 253-003 Coil 6354012 DD 2 7 273-004 Cart SV10-44-0-N-00 2 Notes: 1. Torque HFCART (Item 15) to 25 Ft. Lbs. 2. Torque Coil Nuts (Item 13) to 5 Ft. Lbs.
565 Trailer Sprayer - Parts & Schematics Section F Description: Ref-006421A Vertical Mast Cylinder 23 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Vertical Mast Cylinder Item# Part # 1 TA-02053 Tube Assembly 1 2 RA-01163 Rod 1 3 PI-00002 Piston 1 4 HE-00040 Head 1 5 PP-00014 Locknut, 3/4-16 1 6 MM-00036 Retaining Ring 1 7* O-Ring 1 8* O-Ring 1 9* Back-up 2 10* O-Ring 1 11* Back-up 1 12* O-Ring 1 13* Back-up 1 14* Wiper 1 SK-00924 Description Quantity Seal Kit * Not Sold Separately, Only Available as a Seal Kit.
565 Trailer Sprayer - Parts & Schematics Section F Description: Ref-012419A Ace Hydraulic Pump 25 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Ace Hydraulic Pump Item# Part # Description 1 #4JM Clamp; 1/4 x 5/16 Stainless 2 2 004627 Hyd Hose; 1/2 x 68” MORBX1/2MPT 2 3 150G Gasket; For 2” Flanged Valve 4 4 3A1814 Hosebarb; 1/8 x 1/4, Poly 1 5 8010-15P Hyd Quick Coupler; Univ. Poppet 2 6 BH-038-150-2 Bolt; 3/8” x 1 1/2” Hex. Gr. 2 2 7 FC200BJ Clamp; 2” 4 8 FMCSC150HYD206 Pump; Ace Cent.
565 Trailer Sprayer - Parts & Schematics Section F Description: Ref-009390C 565 Standard Plumbing 27 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: 565 Standard Plumbing Item# Part # 7 3371-0028 8 600432 9 BU038-375-500-2 10 Description Jet Agitator; High Capacity Quantity 2 Hose; 2” Enforcer, Fertilizer Solution U-Bolt; 3/8 x 3 3/4 x 5 Gr.
565 Trailer Sprayer - Parts & Schematics Section F Description: 565 Rinse Tank Kit For Hydraulic Pump 29 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: 565 Rinse Tank Kit For Hydraulic Pump Item# Part # Description Quantity 7 008956 Weldment; Rinse Stand L.S. 8 011612 Hose; 1” 150# Black Rubber 9 150G Gasket; For 2” Flanged Valve 2 10 2000-6 Rinse Nozzle; Tank Rinse 1 11 504-019 Check Valve; 2” (Must be Glued) 1 12 M200FPT Manifold; 2” x 2” Female Thread 1 13 BH-050-150-2 Bolt; 1/2” x 1 1/2” Hex. GR. 2 4 14 BH-050-300-2 Bolt; 1/2” x 3” Hex. GR.
565 Trailer Sprayer - Parts & Schematics Section F Description: Wet Boom Plumbing; 3 Section 31 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Wet Boom Plumbing; 3 Section Item# Part # Description Quantity 1 #12J Clamp, 3/4” Hose Worm Screw 14 2 #16J Clamp; 1” x 1/2 Stainless 5 3 #24J Clamp, 1 1/2” Hose Worm Screw 1 4 #80J Clamp, Hose, 5” x 1/2” Stainless 2 5* 001212 Hose; 3/4” 150# EPDM 6* 011612 Hose; 1” 150# Black Rubber 7* 012412 Hose; 1 1/2” 150# EPDM 8 015814 Flat; .188 x 1.
565 Trailer Sprayer - Parts & Schematics Section F Description: Raven Controls 33 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Raven Controls Item# Part # 1 #24J 2 Description Quantity Clamp, 1 1/2” Hose Worm Screw 2 003667 Plate; Gauge Mount 1 3 006367 Cable; Flow, 12’ w/Packards 1 4 012012 Hose; 1 1/4” 150# Black Rubber 5 063-0171-220 Console Assembly; 450 1 6 063-0171-793 Flow Meter, RFM 60P 1 7 063-0171-894 Valve; Control, 1 1/2” Poly 1 8 106-0159-437 Mounting Bracket 1 9 115-159-492 Cable; Raven Control Cable 1 10 150G Ga
565 Trailer Sprayer - Parts & Schematics Section F Description: Banjo and Strainer Mount; Outer 35 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Banjo and Strainer Mount; Outer Item# Part # 1 016023 2 BH-031-450-5 3 CPC-075 4 Description Quantity Plate; Ball Valve & Strainer Mount 1 Bolt; 5/16 x 4 1/2” Grade 5 2 Clamp; Cobra Poly Pipe 1 FC100 Coupling; 1” FPT 4 5 FW-031 Washer, Flat, 5/16 4 6 LN-031-NI Locknut; 5/16” Nylon Insert 2 7 M100075MPT Fitting; 1” Flange x 3/4” MPT 1 8 M100BRB Hose Barb; 1” x 1” Straight 1 9 M100CPG90 Fitting; 1” 90° Coup
565 Trailer Sprayer - Parts & Schematics Section F Description: 016978A Banjo & Strainer Mount; Center 37 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Banjo & Strainer Mount; Center Item# Part # 1 016023 2 BH-031-450-5 3 CPC-075 4 Description Quantity Plate; Ball Valve & Strainer Mount 1 Bolt; 5/16 x 4 1/2” Grade 5 2 Clamp; Cobra Poly Pipe 1 FC100 Coupling; 1” FPT 5 5 FW-031 Washer, Flat, 5/16 4 6 HB075 Hose Barb; 3/4MPT x 3/4 HB Poly 1 7 LN-031-NI Locknut; 5/16” Nylon Insert 2 8 M100075MPT Fitting; 1” Flange x 3/4” MPT 1 9 M100CPG Flange; 1 x 1 1 10
565 Trailer Sprayer - Parts & Schematics Section F Description: 016014B TeeJet 744 w/ TeeJet Valves w/Flanged Fittings 39 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Item# TeeJet 744 w/ TeeJet Valves w/Flanged Fittings Part # Description Clamp; 1” x 1/2” Stainless Quantity 1 #16J 3 2 011612 Hose; 1” 150# Black Rubber 3 150G Gasket; for 2” Flanged Valve 5 4 21720-15 Cable Assembly; 15’ Ext.
565 Trailer Sprayer - Parts & Schematics Section F Description: TeeJet & Strainer Mount; Outer 41 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: TeeJet & Strainer Mount; Outer Item# Part # Description 1 016023 Plate; Ball Valve & Strainer Mount 1 2 016790 Valve; 1” Elec.
565 Trailer Sprayer - Parts & Schematics Section F Description: 016977A TeeJet & Strainer Mount; Center 43 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: TeeJet & Strainer Mount; Center Item# Part # Description 1 016023 Plate; Ball Valve & Strainer Mount 1 2 016790 Valve; 1” Elec.
565 Trailer Sprayer - Parts & Schematics Section F 45 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Item# 9 Gallon Tank Assembly Part # 1 016201 2 Description Quantity Weldment; Safety Tank Mount, 565 1 6000-30Y Tank; 9 Gal. Rinse Tank, Yellow 1 3 0009-UY Tank; 9 Gal. Tank, Molded (Yellow) 1 4 RW01 Rivet Washer, 3/8 OD x 3/16 ID 4 5 000016 Cover, 9 Gal. Tank Molded 1 6 0001-U Lid, 9 Gal.
565 Trailer Sprayer - Parts & Schematics Section F Description: Ref-013505B Sprayer Eductor 47 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Sprayer Eductor Item# Part # 1 013487 2 V-150 3 HB-150-90 4 #28J 5 012412 6 Description Quantity Eductor, Hypro Clean Load 1 Valve, 1 1/2 Bolt, FNPT 1 Hose Barb, 1 1/2 MNPT, 1 1/2 HB, EL 1 Clamp; 1 1/2 Hose 4 Hose, 1 1/2” 150# EPDM 6 NIP200-SH Nipple, 2” Short 1 7 FC200BJ Clamp, 2” FLG 1 8 RB200-125 Reducer Bushing; Poly 2 x 1 1/4 1 9 HB-125-90 Hose Barb, 1 1/4 MPT x 1 1/4 HB 2 10 012012 Hose; 1 1/4 1
565 Trailer Sprayer - Parts & Schematics Section F 49 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Manual Fence Row Nozzle Assembly Item# Part # 1 #12J 2 000612 3 3EL1438 4 Description Quantity Clamp, 3/4” Hose Worm Screw 2 Hose; 3/8” 150# EPDM(Not Shown) - Elbow; 1/4MPT x 3/8 ELHB 1 3EL38 Hose Fitting: 3/8 MPT x 3/8 HB 1 5 3FC34 Coupling; 3/4, FPT, Poly 1 6 3M3438 Nipple; 3/4 x 3/8, Reduc, Poly 1 7 90FFB38 Valve; 3/8 Female NPT, Brass 1 8 QJ1/4T-NYB QJ-1/4T Quickjet Body 1 50 Section F 3-07
565 Trailer Sprayer - Parts & Schematics Section F Description: Raven Proximity Sensor Item# Part # Description 1 010439 Weldment; Axle Mount 1 2 010442 Rod; Adjustment 1 3 010443 Weldment; Sensor Mount 1 4 171-C Screw; TEK 410HSS Cad Plated 2 5 063-0159-982 Sensor; Gear Tooth Speed 1 6 115-0159-018 Cable; Speed Sensor 24’ Ext. Cable 1 7 BH-025-075-2 Bolt; 1/4 x 3/4 Gr.
565 Trailer Sprayer - Warranty Section G 3-07
565 Trailer Sprayer - Warranty Section G Serial and Model Number Location Model and Serial Number Plate Hitch/Drawbar Tubes (Front of Sprayer) Model and Serial Number Plate The following page contains a space for you to record the information about your sprayer found on this plate. Please record this information here for future reference. SERIAL NUMBER INFORMATION Redball® Model Number: Redball® Serial Number: Component Serial Numbers: Manufacturer Part Number IMPORTANT Serial No.
565 Trailer Sprayer - Warranty Section G NEW PRODUCT WARRANTY Redball, LLC warrants each new Redball® product to be free under normal use and service from defects in workmanship and materials for a period of one (1) year from the date of first use.
The Employees of would like to thank you for purchasing this Redball® 565 Trailer Sprayer.
To Our Valued Redball Customer: I would like to take this opportunity to personally thank you for your recent Redball® purchase. In an effort to serve you better, please take a moment to warranty register your new Redball® product. Warranty registration provides Redball, LLC the information necessary to contact and inform you through Redball® Customer Services.
Place Stamp Here TY AN ION R T R WA RMA O INF Redball, LLC 140 30th Ave SE PO Box 159 Benson, MN 56215 3-07
