VENT-FREE GAS WALL HEATER OWNER’S OPERATION AND INSTALLATION MANUAL INFRARED MODELS IWH10NLTC IWH16NLTC IWH26NLTC PFS ® US WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. — Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance.
TABLE OF CONTENTS Safety......................................................... 3 Specifications............................................. 4 Qualified Installing Agency......................... 5 Product Features........................................ 5 Local Codes............................................... 5 Preparing For Installation........................... 6 Unpacking.................................................. 6 Water Vapor: A By-Product Of Unvented Room Heaters.......................
SAFETY IMPORTANT: Read this owner’s manual carefully and completely before trying to assemble, operate, or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, explosion, electrical shock and carbon monoxide poisoning. Only a qualified installer, service agent, or local gas supplier may install and service this product. WARNING: Keep the appliance area clear and free from combustible materials, gasoline, and other flammable vapors and liquids.
SAFETY 1. Do not place Propane/LP supply tank(s) inside any structure. Propane/LP supply tank(s) must be placed outdoors. 2. Heaters 10,000 Btu/Hr or more shall not be installed in a bedroom or bathroom. 3. This heater needs fresh air ventilation to run properly. This heater has an Oxygen Depletion Sensing (ODS) safety shutoff system. The ODS shuts down the heater if not enough fresh air is available. See Air for Combustion and Ventilation, page 7. If heater keeps shutting off, see Troubleshooting, page 21.
QUALIFIED INSTALLING AGENCY Only a qualified agency should install and replace gas piping, gas utilization equipment or accessories, and repair and equipment servicing.
PREPARING FOR INSTALLATION Before beginning assembly or operation of the product, make sure all parts are present. Compare parts with package contents list. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts. Ignitor Control Knob Button Grill Burner Front Panel Base (Optional) Heater Cabinet Figure 1 - Vent-Free Gas Heater UNPACKING 1. Remove heater from carton. 2.
AIR FOR COMBUSTION AND VENTILATION WARNING: This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air. Read the following instructions to insure proper fresh air for this and other fuel-burning appliances in your home. Today’s homes are built more energy efficient than ever. New materials, increased insulation and new construction methods help reduce heat loss in homes.
AIR FOR COMBUSTION AND VENTILATION Ventilation Air Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Air for Combustion and Ventilation for required size of ventilation grills or ducts.
INSTALLATION NOTICE: This heater is intended for use as supplemental heat. Use this heater along with your primary heating system. Do not install this heater as your primary heat source. If you have a central heating system, you may run system’s circulating blower while using heater. This will help circulate the heat throughout the house. In the event of a power outage, you can use this heater as your primary heat source.
INSTALLATION GAS SELECTION This appliance is factory preset for propane/LP gas. No changes are required for connecting to propane/LP. Only a qualified installer or service technician can perform gas selection and connecting to gas supply. CAUTION: Two gas line installations at the same time are prohibited. The access plate to the simple switching means shall not be opened while the heater is in operation.
INSTALLATION 1. 2. 3. 4. For changing from natural gas supply to propane supply: Remove 2 screws from cover plate located on back of heater to expose fuel selection device (see Figure 6). For propane gas, press in knob using a flat screwdriver with a blade the thickness of a quarter and turn knob counterclockwise until the knob locks into the LP position (see Figure 6). Fuel selection device must be locked in the LP position. Do not operate heater between locked positions.
INSTALLATION Methods For Attaching Mounting Bracket To Wall Use only the last hole on each end of mounting bracket to attach bracket to wall. Attach mounting bracket to a wall only in one of two ways: 1. Attaching to wall stud: This method provides the strongest hold. Insert mounting screws through mounting bracket and into wall studs. 2. Attaching to wall anchor: This method allows you to attach mounting bracket to hollow walls (wall areas between studs) or to solid walls (concrete or masonry).
INSTALLATION 3. Insert wall anchor (wings first) into hole. Tap anchor flush to wall. 4. For thin walls (1/2" or less), insert red key into wall anchor. Push red key to “pop” open anchor wings (see Figure 11, page 12). IMPORTANT: Do not hammer anchor key! For thick walls (over 1/2" thick) or solid walls, do not pop open wings. 5. Place mounting bracket onto wall. Line up last hole on each end of bracket with wall anchors. 6. Insert mounting screws through bracket and into wall anchors. 7.
INSTALLATION CONNECTING TO GAS SUPPLY WARNING: A qualified service technician must connect heater to gas supply. Follow all local codes. WARNING: This appliance requires a 3/8” NPT (National Pipe Thread) inlet connection to the pressure regulator. WARNING: For natural gas, Never connect heater to private (non-utility) gas wells. This gas is commonly known as wellhead gas. WARNING: Do not overtighten gas connections. CAUTION: Use only new, black iron or steel pipe.
INSTALLATION Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged heater valves. For propane/LP gas, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11" and 14" of water. If you do not reduce incoming gas pressure, heater regulator damage could occur.
INSTALLATION 4. Check all joints of gas supply piping system. Apply a noncorrosive leak detection fluid to all joints. If bubbles form, there may be a leak. 5. Correct all leaks at once. 6. Reconnect heater and equipment shutoff valve to gas supply. Check reconnected fittings for leaks. Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa) 1. Close equipment shutoff valve (see Figure 16). 2.
OPERATION FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor.
OPERATION Note: If pilot goes out, repeat steps 3 through 7. This heater has a safety interlock system. Wait one (1) minute before lighting pilot again. 8. Turn control knob counterclockwise to desired heating level. The main burner should light. Set control knob to any heat level between 1 and 5. IWH10NLTC CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve. WARNING: If input gas type is NG, make sure NG pilot burner ignites.
INSPECTING HEATER IMPORTANT: Owner’s should check pilot flame pattern and burner flame pattern often. Incorrect flame patterns indicate the need for cleaning (see Care and Maintenance, page 20) or service. WARNING: Only a qualified service person should service and repair heater. This includes maintenance requiring replacement or alteration of components. PILOT FLAME PATTERN Figure 22 shows a correct pilot flame pattern. Figure 23 shows an incorrect pilot flame pattern.
CARE AND MAINTENANCE WARNING: Turn off heater and let cool before servicing. CAUTION: You must keep control areas, burner, and circulating air passageways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service technician. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, pet hair, etc. WARNING: Failure to keep the primary air opening(s) of the burner(s) clean may result in sooting and property damage.
TROUBLESHOOTING WARNING: If you smell gas: • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department. WARNING: Only a qualified service technician should service and repair heater. Make sure that power is turned off before proceeding.
TROUBLESHOOTING Problem Possible Cause Corrective Action ODS/pilot lights but flame 1. Control knob is not fully 1. Press in control knob fully. goes out when control pressed in. knob is released. 2. Control knob is not pressed 2. After ODS/pilot lights, keep in long enough. control knob pressed in 30 seconds. 3. Equipment shutoff valve is 3. Fully open equipment shutoff not fully open. valve. 4. Thermocouple connection is 4. Hand tighten until snug, and loose at control valve.
TROUBLESHOOTING Problem Possible Cause Corrective Action Slight smoke or odor 1. Residues from manufactur- 1. Problem will stop after a few during initial operation. ing process. hours of operation. Heater produces a whis- 1. Turning control knob to high 1. Turn control knob to low (1) position and let warm up for tling noise when burner (5) position when burner is a minute. is lit. cold. 2. Operate burner until air is 2. Air in gas line. removed from line. Have gas line checked by local gas supplier. 3.
REPLACEMENT PARTS Note: Use only original replacement parts. This will protect your warranty coverage for parts replaced under warranty. PARTS UNDER WARRANTY Call Customer Service toll free at 1-800-229-5647 to order parts under warranty.
SERVICE HINTS When Gas Pressure Is Too Low • pilot will not stay lit • burners will have delayed ignition • fireplace will not produce specified heat • propane/LP gas supply might be low (propane/LP units only) You may feel your gas pressure is too low. If so, contact your local gas supplier. TECHNICAL SERVICE You may have further questions about installation, operation, or troubleshooting. If so, contact SHM International, Corp. at 1-800-229-5647.
PARTS MODEL IWH10NLTC 16 1 15 2 12 5 3 6 7 8-1 8-2 4 11 13 17 26 9 10 www.sureheat.
PARTS MODEL IWH10NLTC This list contains replaceable parts for your heater. When ordering replacement parts, follow the instructions listed under Replacement Parts on page 24 of this manual.
PARTS MODEL IWH16NLTC 16 1 15 12 2 5 11 6 3 7 9 8-1 8-2 10 13 4 19 17 14 18 28 www.sureheat.
PARTS MODEL IWH16NLTC This list contains replaceable parts for your heater. When ordering replacement parts, follow the instructions listed under Replacement Parts on page 24 of this manual.
PARTS MODEL IWH26NLTC 16 1 15 12 2 5 11 6 7 3 10 8-1 8-2 9 13 19 17 14 4 30 www.sureheat.
PARTS MODEL IWH26NLTC This list contains replaceable parts for your heater. When ordering replacement parts, follow the instructions listed under Replacement Parts on page 24 of this manual.
WARRANTY KEEP THIS WARRANTY Model ________________________________ Serial No. _____________________________ Date Purchased ________________________ Keep receipt for warranty verification. IMPORTANT: We urge you to fill out your warranty information above. Complete with the entire serial number which can be found on the rating plate. Retain this manual for future reference. Always specify model and serial numbers when communicating with customer service.
CALENTADOR DE GAS DE PARED SIN VENTILAS MANUAL DE FUNCIONAMIENTO E INSTALACIÓN DEL PROPIETARIO INFRARROJO MODELOS IWH10NLTC IWH16NLTC IWH26NLTC PFS ® US ADVERTENCIA: Este aparato está equipado para funcionar con gas (natural y propano). No se permite convertir más que a gas natural o gas propano.
TABLA DE CONTENIDOS Seguridad................................................. 35 Especificaciones....................................... 37 Agencia de Instalación Calificada............ 37 Características del Producto.................... 38 Normas Locales....................................... 38 Preparación Para la Instalación............... 39 Desempaque............................................ 39 Vapor De Agua: Un Producto Derivado de Los Calentadores de Habitación Sin Ventilación....................
SEGURIDAD IMPORTANTE: Lea este manual del propietario cuidadosa y completamente antes de intentar ensamblar, operar o dar servicio a este calentador. El uso inadecuado de este calentador puede causar daños a la propiedad, lesiones graves o la muerte por quemaduras, incendio, explosión, electrocución e intoxicación con monóxido de carbono. No seguir estas instrucciones anula la garantía.
SEGURIDAD ADVERTENCIA: Este calentador alcanza temperaturas muy altas cuando el calentador está en funcionamiento. Mantenga a niños y adultos alejados de las superficies calientes para evitar quemaduras o que la ropa se encienda. El calentador permanecerá caliente durante algún tiempo después de que se ha apagado. Permita que la superficie se enfríe antes de tocarla. ADVERTENCIA: No coloque ropa ni otros materiales inflamables sobre el aparato ni cerca del mismo.
ESPECIFICACIONES MODELO Encendido Tipo de gas BTU (disponible) Ajuste del regulador de presión: Presión del gas de entrada* (pulg. de agua) Tipo de gas BTU (disponible) Ajuste del regulador de presión: Presión del gas de entrada* (pulg.
CARACTERÍSTICAS DEL PRODUCTO PILOTO DE SEGURIDAD El calentador posee un piloto que cuenta con un sistema de apagado de seguridad por medio de un sensor de agotamiento de oxígeno (ODS). El sensor de agotamiento de oxígeno del piloto apaga el calentador si no hay suficiente cantidad de aire fresco. 2 OPCIONES DE GAS DISPONIBLES El calentador está diseñado para funcionar con gas propano o con gas natural. El calentador es enviado de fábrica listo para conectarse a gas propano.
PREPARACIÓN PARA LA INSTALACIÓN Antes de ensamblar u operar el producto, asegúrese de tener todas las piezas. Compare las piezas con la lista del contenido del paquete. Si hay piezas dañadas o si faltan piezas, no intente armar, instalar ni usar el producto. Póngase en contacto con el servicio al cliente para obtener piezas de repuesto. Rejilla Botón de encendido Perilla de control Quemador Panel anterior Base (opcional) Gabinete del calentador Figura 1 - Calentador de gas sin ventilación DESEMPAQUE 1.
AIRE PARA COMBUSTIÓN Y VENTILACIÓN ADVERTENCIA: Este calentador no debe instalarse en un espacio confinado ni en una construcción inusualmente sellada, a menos que se hayan tomado las medidas necesarias para proporcionar el aire adecuado para la combustión y la ventilación. Lea las instrucciones siguientes para asegurarse de que su hogar cuente con la cantidad adecuada de aire fresco para éste y otros aparatos que queman combustible.
AIRE PARA COMBUSTIÓN Y VENTILACIÓN Aire del exterior Proporcione aire fresco adicional mediante el uso de rejillas o conductos de ventilación. Debe haber dos aberturas permanentes: una a 30.48 cm (12") del techo y otra a 30.48 cm (12") del suelo. Conecte estos elementos directamente al exterior o a los espacios que estén abiertos al exterior. Estos espacios incluyen áticos y espacios debajo del piso de la casa. Consulte el Código Nacional de para ventilación Gas Combustible, ANSI Z223.
INSTALACIÓN AVISO: Este calentador está diseñado para utilizarse como calefacción adicional. Use este calentador junto con su sistema de calefacción principal. No instale este calentador como fuente de calefacción principal. Si tiene un sistema de calefacción central, puede activar el ventilador de circulación del sistema mientras utiliza el calentador. Esto ayudará a que el calor circule por toda la casa.
INSTALACIÓN DISTANCIA DE SEPARACIÓN DE COMBUSTIBLES Siga con atención las siguientes instrucciones. Este calentador es una unidad de montaje en la pared diseñada para apoyarse directamente sobre el suelo o una base de repisa. ADVERTENCIA: Mantenga las distancias mínimas como se muestra en la Figura 4. Si es posible, proporcione distancias mayores respecto al suelo, al techo y a las paredes adyacentes. Mida desde el punto más alejado del calentador. TECHO 20.
INSTALACIÓN Para cambiar de gas propano a gas natural: 1. Retire los 2 tornillos de la placa de la Perilla de cubierta situados en la parte posterior NG selección de del calentador para exponer dispositivo combustible de selección de combustible (consulte la Figura 5). LP 2.
INSTALACIÓN UBICACIÓN DEL CALENTADOR Este calentador está diseñado para montarse en la pared. Para mayor comodidad y eficiencia, instale el calentador: • Donde haya fácil acceso para la operación, inspección y servicio. • En el lugar más frío de la habitación. COLOCACIÓN DEL CALENTADOR EN LA PARED Soporte de montaje El soporte de montaje se encuentra en el panel posterior del calentador (consulte la Figura 7). Se colocó con cinta en ese lugar para el transporte.
INSTALACIÓN Instalación del soporte de montaje a la pared Nota: Los anclajes de pared, los tornillos de montaje y los separadores se encuentran en el paquete de ferretería. El paquete de ferretería se incluye con el calentador. Método de fijación a viga de pared Para fijar el soporte de montaje a las vigas de pared: 1. Perfore orificios en los lugares marcados utilizando una broca de 9/64". 2. Coloque el soporte de montaje en la pared.
INSTALACIÓN Colocación del calentador en el soporte de montaje 1. Localice las dos ranuras horizontales en el panel posterior del calentador (consulte la figura 12). 2. Coloque el calentador en el soporte de montaje. Deslice las ranuras horizontales hacia las lengüetas salientes del soporte de montaje. Ranuras horizontales Soporte de montaje (fijado a la pared) Lengüeta saliente Figura 12 - Montaje del calentador en el soporte de montaje Instalación de los tornillos de montaje inferiores 1.
INSTALACIÓN CONEXIÓN AL SUMINISTRO DE GAS ADVERTENCIA: Una persona de servicio capacitada debe conectar el calentador al suministro de gas. Siga todas las normas locales. ADVERTENCIA: Este aparato requiere una conexión de entrada tipo NPT (rosca de tubería nacional) de 3/8" al regulador de presión. ADVERTENCIA: Para gas natural, nunca conecte el calentador a pozos de gas privados (que no sean de servicio público). Este gas se conoce comúnmente como gas de pozo.
INSTALACIÓN Antes de instalar el calentador, asegúrese de tener los elementos que se indican a continuación.
INSTALACIÓN REVISIÓN DE LAS CONEXIONES DE GAS ADVERTENCIA: Después de instalar el calentador o de darle servicio, pruebe todas las conexiones y tubos de gas de la unidad, tanto internas como externas, en busca de fugas. Repare todas las fugas inmediatamente. ADVERTENCIA: Nunca use una llama al descubierto para verificar si hay fugas. Aplique líquido no corrosivo para detectar fugas en todas las uniones. La formación de burbujas indicará una fuga. Repare todas las fugas inmediatamente.
INSTALACIÓN Comprobación de la presión de las conexiones de gas del calentador 1. Abra la válvula de cierre del equipo (consulte la figura 16, página 50). 2. Si usa gas natural, abra la válvula principal de gas ubicada en el medidor de gas o cerca de éste. Si usa propano o gas LP, abra la válvula de suministro de propano o gas LP. 3. Compruebe que la perilla de control del calentador esté en la posición OFF (apagado). 4.
FUNCIONAMIENTO INSTRUCCIONES DE ENCENDIDO 1. ¡ALTO! Lea la información de seguridad en la página 51. 2. Asegúrese de que la válvula de cierre del equipo esté totalmente abierta. 3. Gire la perilla de control en dirección de la manecillas del reloj hasta la posición OFF (apagado). 4. Espere cinco minutos a que se disipe el gas. Luego, compruebe que no huela a gas, incluso cerca del piso. Si percibe olor a gas, ¡DETÉNGASE! Siga el punto “B” en la información de seguridaden la página 51.
FUNCIONAMIENTO IWH10NLTC IWH16NLTC IWH26NLTC Quemadors Perilla de control Figura 20 - Patrón del quemador FUNCIONAMIENTO DEL CONTROL CON TERMOSTATO El termostato que se usa en este calentador detecta la temperatura de la habitación. Algunas veces, la temperatura de la habitación puede ser mayor que la establecida. Si esto ocurre, el quemador se apagará. El quemador volverá a encenderse cuando la temperatura de la habitación disminuya por debajo de la temperatura que se estableció.
INSPECCIÓN DEL CALENTADOR IMPORTANTE: El propietario debe revisar frecuentemente los patrones de la llama del piloto y de la llama del quemador. Patrones de llama incorrectos indican la necesidad de limpieza o servicio de mantenimiento (consulte Cuidado y mantenimiento, página 55). ADVERTENCIA: Sólo una persona de servicio capacitada debe repararlo o darle servicio. Esto incluye el mantenimiento requerido, refacciones o alteración de componentes.
CUIDADO Y MANTENIMIENTO ADVERTENCIA: Apague el calentador y deje que se enfríe antes de darle mantenimiento. PRECAUCIÓN: Debe mantener limpias las áreas de control, el quemador y las vias de circulación de aire del calentador. Inspeccione estas áreas del calentador antes de cada uso. Haga que una persona de servicio calificada inspeccione el calentador una vez al año.
SOLUCIÓN DE PROBLEMAS ADVERTENCIA: Si percibe olor a gas • Cierre el suministro de gas. • No intente encender ningún aparato. • No toque ningún interruptor eléctrico; no use ningún teléfono en el edificio. • Llame inmediatamente a su proveedor de gas desde el teléfono de algún vecino. Siga las instrucciones del proveedor de gas. • Si no puede localizar al proveedor de gas, llame al departamento de bomberos. ADVERTENCIA: Sólo una persona de servicio capacitada debe reparar la calentador y darle servicio.
SOLUCIÓN DE PROBLEMAS Problema Causa Posible Acción correctiva Cuando se presiona el 1. El suministro de gas está 1. Abra el suministro de gas o la botón del encendedor, cerrado o la válvula de cieválvula de cierre del equipo. hay chispa en el piloto/ rre del equipo está cerrada. ODS pero no se en- 2. La perilla de control no se 2. Presione la perilla de control ciende. presionó del todo al pulsar del todo al pulsar el botón el botón de encendido. de encendido. 3. Quedó aire en las líneas 3.
SOLUCIÓN DE PROBLEMAS Problema Causa Posible Acción correctiva El quemador no se en- 1. El orificio del quemador 1. Limpie el quemador (consulte ciende después de que el está tapado. Cuidado y mantenimiento, en piloto/ODS se enciende. la página 55) o remplace el quemador. 2. El diámetro del orificio del 2. Remplace el orificio del quequemador es demasiado mador. pequeño. 3. La entrada de la presión de 3. Contacte a su proveedor local gas es demasiado baja. de gas. Encendido demorado del 1.
SOLUCIÓN DE PROBLEMAS Problema Causa Posible Acción correctiva El calentador produce un 1. Se giró la perilla de control 1. Gire la perilla de control a la silbido cuando el quemaa la posición alto (5) cuanposición bajo (1) y deje que se dor está encendido. do el quemador estaba frío. caliente durante un minuto. 2. Hay aire en la tubería de 2. Haga funcionar el quemador gas. hasta que se elimine el aire de la tubería. Pida a la empresa proveedor local de gas que revise la línea de gas. 3.
SOLUCIÓN DE PROBLEMAS Problema Causa Posible Acción correctiva El calentador se apaga 1. No hay suficiente aire fres- 1. Abra la ventana y/o la puerta mientras se está usando co. para proporcionar ventilación. (el ODS funciona). 2. Hay poca presión en la 2. Contacte a su proveedor local tubería. de gas. 3. El piloto/ODS está parcial- 3. Limpie el piloto/ODS (consulte mente tapado. Cuidado y mantenimiento, en la página 55). Hay olor a gas incluso 1. Fugas de gas. Consulte la 1.
ACCESORIOS Adquiera estos accesorios con su distribuidor local. Si no pueden proporcionarle estos accesorios, comuníquese SHM International, Corp. al 1-800-229-5647 para obtener información. VÁLVULA DE INTERRUPCIÓN DE EQUIPOS RMH-120-00088 Para todos los modelos. Válvula de interrupción de equipos con 1/8". Llave de paso del TNP. CONSEJOS PARA SERVICIO Cuando la presión del gas de entrada sea muy baja • El piloto no permanecerá encendido. • El quemador tendrá un retraso durante el encendido.
PIEZAS MODELO IWH10NLTC 16 1 15 2 12 5 3 6 7 8-1 8-2 4 11 13 17 62 9 10 www.sureheat.
PIEZAS MODELO IWH10NLTC Esta lista contiene las piezas remplazables utilizadas en el calentador. Al hacer un pedido de piezas, siga las instrucciones listadas en Piezas de repuesto en la página 60 de este manual. Art. Piezo # Descripción Cant.
PIEZAS MODELO IWH16NLTC 16 1 15 12 2 5 11 6 3 7 9 8-1 8-2 10 13 4 19 17 14 18 64 www.sureheat.
PIEZAS MODELO IWH16NLTC Esta lista contiene las piezas remplazables utilizadas en el calentador. Al hacer un pedido de piezas, siga las instrucciones listadas en Piezas de repuesto en la página 60 de este manual. Art. Pieza # Descripción Cant.
PIEZAS MODELO IWH26NLTC 16 1 15 12 2 5 11 6 7 3 10 8-1 8-2 9 13 19 17 14 4 66 www.sureheat.
PIEZAS MODELO IWH26NLTC Esta lista contiene las piezas remplazables utilizadas en el calentador. Al hacer un pedido de piezas, siga las instrucciones listadas en Piezas de repuesto en la página 60 de este manual. Art. Pieza # Descripción Cant.
GARANTÍA GUARDE ESTA GARANTÍA Modelo___________________________________ Número de serie___________________________ Fecha de compra __________________________ Conserve su recibo para la verificación de la garantía. IMPORTANTE: Le pedimos que complete la información de su garantía antes mencionada. Completo con todo el número de serie que se puede encontrar en la placa de características. Conserve este manual para futuras consultas.