SERIES: 1200 CONFIGURATION: Door-Door MOUNTING PACKAGE: Frameless, sliding door RDQCI5022 Rev.
Tools: To install your New Shower Enclosure, you may need the following: Drill Pencil Hack Saw 1/8” & 3/16” Drill Bit Low Tack Tape Caulk Gun Center Punch Tape Measure Clear Silicone Caulk Files 4’ & 6’ Levels Suction Cups #2 Phillips Screwdriver Safety Notes: This unit is best installed by two people. Handle the glass panels carefully and protect the edges.
PARTS LIST ITEM DESCRIPTION QTY. A Tub Track with Vinyl 1 B Wall Jambs 2 C Plastic Wall Anchors 6 D #8 x 1 1/2” Truss Head Screws 6 E 2 Nylon Spacers 4 F Header 1 G Glass panels 2 H Hanger Brackets (Pre-assembled) 4 I Back Plates 4 J Clear Plastic Discs 8 K Glass Hole Sleeves 4 L Front Plates 4 N Towel Bar 2 S Nylon Bottom Guide 1 T #6 x 3/8” Pan Head Screw 2 U Stainless Bumper Inserts 4 V Vinyl Jamb Bumpers 4 X Allen Wrench *Quantities may vary.
EXPLODED VIEW RDQCI5022 Rev.
1 Measure the wall-to-wall opening at the center of the tub rim. Cut the tub track [A] 1/16” short of this dimension. An inexpensive miter box available at your local hardware store will help you get clean square cuts. • • • • • • • • • • • • • • • • • • Position the tub track in the center of the tub rim with the tall leg to the exterior. It may be necessary to file a radius on the ends of the tub track and wall jambs to match the corners of the tub.
4 Replace one wall jamb [B] and attach to the wall with a #8 x 2” truss head screw [D] inserted through the center hole. Slip a nylon spacer [E] over a #8 x 2” truss head screw and install in the top hole of the wall jamb. Repeat for the bottom jamb. Check jamb for plumb and tighten screws. WALL JAMB NYLON SPACER NOTE: Do not over-tighten the jamb screws. #8 x 2” TRUSS HEAD SCREW 5 This bath enclosure is equipped with safety teelock wall jambs.
Slide one of the clear plastic discs [J], then a glass hole sleeve [K] onto the back plate [I]. Push the assembly through the hole in the glass panel, so that the glass hole sleeve is flush with the other side of the panel. Slide the other clear plastic disc onto the protruding end of the back plate, and then slide on the front plate [L]. Repeat this for the second hole on the panel. While holding the towel bar [N] in place, and screw the back plates into the towel bar.
10 Locate the nylon bottom guide [S] in the middle of the tub track [A] with the glass panels in the position shown. With a 7/64” bit, drill two holes into the V-groove through the mounting holes in the guide. Install the bottom guide with two #6 x 3/8” pan head screws [T] thru the drilled holes as shown.
CURVED TOWEL BAR SUPPLEMENT Slide one of the clear plastic discs [J], then a glass hole sleeve [K] onto the back plate [I]. Push the assembly through the hole in the glass panel, so that the glass hole sleeve is flush with the other side of the panel. Slide the other clear plastic disc onto the protruding end of the back plate, and then slide on the front plate [L]. Repeat this for the second hole on the panel. While holding the towel bar [N] in place, and screw the back plates into the towel bar. I. J. K.
Tile Ready® Brand Shower Pan Installation Addendum SPECIAL INSTRUCTIONS FOR REDI DOOR® ENCLOSURE INSTALLATIONS WITH TILE READY® BRAND SHOWER PANS Designated screw pack for Tile Ready® Brand Shower Pans: For Redi Door® enclosure installations with a Tile Ready® brand shower pan, a special screw pack containing eight (8) #8x¾” pan-head screws is included with your door. These #8x¾”screws replace curb screws included in the main hardware package, and their use is mandatory.
