Manualshelf

Application Guide

ManualsBrandsRedLine Tools ManualsBall Nose End MillsRedLine Tools - .0250 Single End Ball Carbide End Mill, AlTiN Coated .0750 Flute Length, 4 Flute, 30° Helix Angle.2500 Length Below Shank, 1.5000 OAL - RET9025
1
redlinetools.com
800.791.7542
215
Endmills - Technical Info
Endmills
Tech Info -
General Purpose Micro Endmills Speeds & Feeds
Material Grades
SFM SFM Feed by Endmill Diameter (IPT)
Uncoated AlTiN (.0050) (.0150) (.0300) (.0450) (.0600) (.0750) (.1000)
P - Steels
High Strength Tool Steel A2, D2, P20, H11, H13, S2, 01 240 300 .00002 .00005 .00010 .00014 .00019 .00024 .00032
High Strength Tool Steel >32 HRC N/A N/A N/A N/A N/A N/A N/A N/A N/A
Low Carbon
A36, 12L14, 12L15, 1005, 1018, 1020,
1108-1119, 1213-1215, 1513-1518,
4012, 5015, 9310
280 350 .00003 .00010 .00019 .00029 .00038 .00048 .00064
Low Carbon >32HRC N/A N/A N/A N/A N/A N/A N/A N/A N/A
Medium Carbon
1040-1095, 1140-1151, 1330-1345,
1520-1572, 4023-4063, 4120-4161,
4330-4340, 4620-4640, 8620-8660,
8740-8750, 6150, 51000, 52100
200 250 .00002 .00005 .00010 .00014 .00019 .00024 .00032
Medium Carbon >32 HRC N/A N/A N/A N/A N/A N/A N/A N/A N/A
M - Stainless Steels
Austenitic 301-304L, 310, 316L, 321, 347 180-400 225-500 .00002 .00006 .00012 .00018 .00024 .00030 .00040
Austenitic >32 HRC N/A N/A N/A N/A N/A N/A N/A N/A N/A
Martensitic 403, 410, 416, 420, 430, 431, 440 160 200 .00002 .00005 .00010 .00014 .00019 .00024 .00032
Martensitic >32 HRC N/A N/A N/A N/A N/A N/A N/A N/A N/A
Precipitation Hardening
12/8, 15/5, 17/4, AM-350/355/ 363,
PH13-8MO, PH14-8/MO
160 200 .00002 .00005 .00010 .00014 .00019 .00024 .00032
Precipitation Hardening >32 HRC N/A N/A N/A N/A N/A N/A N/A N/A N/A
K - Cast Irons
Ductile A536, J434, 60-40-18 280 350 .00005 .00014 .00029 .00043 .00058 .00072 .00096
Gray A48, A436, A319, Class 20, G4000 400 500 .00006 .00019 .00038 .00058 .00077 .00096 .00128
Malleable A220, A602, J158 270 330 .00005 .00014 .00029 .00043 .00058 .00072 .00096
N - Non-Ferrous
Aluminum Alloys Max RPM Max RPM .00013 .00038 .00077 .00115 .00154 .00192 .00256
Aluminum High Silicon Max RPM Max RPM .00006 .00019 .00038 .00058 .00077 .00096 .00128
Brass/Bronze Aluminum Bronze, Low Silicon Bronze 600 750 .00006 .00019 .00038 .00058 .00077 .00096 .00128
Composites
G-10, Fiberglass, Graphite, Graphite
Epoxy, Plastics
800 1000 .00013 .00038 .00075 .00113 .00150 .00188 .00250
Copper 480 600 .00006 .00019 .00038 .00058 .00077 .00096 .00128
Magnesium Max RPM Max RPM .00013 .00038 .00077 .00115 .00154 .00192 .00256
S - High Temp Alloys
Cobalt Base Stellite, HS-21, Haynes 25/188, 80 100 .00002 .00005 .00011 .00016 .00022 .00027 .00036
Cobalt Base >32HRC X40, L605 N/A N/A N/A N/A N/A N/A N/A N/A N/A
Iron Base Incoloy 800-802, Multmet N-155 80 100 .00002 .00005 .00011 .00016 .00022 .00027 .00036
Iron Base >32HRC Timkin 16-25-6, Carpenter 22-b3 N/A N/A N/A N/A N/A N/A N/A N/A N/A
Nickel Base Inconel 625/718, Inco 700, 713C, 718 80 100 .00002 .00005 .00011 .00016 .00022 .00027 .00036
Nickel Base >32HRC
Monel 400-401, 404, K401, Rene,
Rene 41 & 95 Hastelloy, Waspoloy,
Udimet 500 & 700
N/A N/A N/A N/A N/A N/A N/A N/A N/A
Titanium
Commercially Pure, 6Al-4V, ASTM
1/2/3, 6Al-25N-4Zr-2Mo-Si, Ti-8Al-
1Mo, Ti-8Al-4Mo
200 250 .00002 .00007 .00014 .00022 .00029 .00036 .00048
NOTE: Speeds and Feeds listed are estimated and will vary by application.
These General Purpose tools can be found on pages 102-105, 110-113, 134-138, 160-164.

Summary of content (1 pages)