848-D13-93A1 (501) OWNER / OPERATOR MANUAL HEDGE-TRIMMERS HT2200 CHT2200 WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Thank you for purchasing a RedMax product. Before using our hedge-trimmers, please read this manual carefully to understand the proper use of your unit.
Read this manual carefully to understand all safety precautions, controls, proper operation and maintenance of your RedMax hedgetrimmers. Failure to do so could result in serious injury. SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail.
CONTENTS SAFETY PRECAUTIONS · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 4 PROPER AND SAFE OPERATION OF YOUR HEDGE-TRIMMER WORK GEAR AND CLOTHING WARNINGS CONSIDERING HANDLING OF FUEL THINGS TO CHECK BEFORE USING YOUR HEDGE-TRIMMER THINGS TO CHECK BEFORE STARTING UP THE ENGINE AVOID NOISE PROBLEM THINGS TO BE CAREFUL ABOUT WHEN USING YOUR HEDGE-TRIMMER NOTES ON CARE AND MAINTENANCE OF YOUR HEDGE-TRIMMER PARTS LOCATION & SPECIFICATIONS · · · · · · · · · · · · · · · · · · · · ·
Safety Precautions ■ IN ORDER TO ENSURE PROPER AND SAFE OPERATION OF YOUR HEDGE-TRIMMER • Read this Owner/Operator Manual carefully. Be sure you understand how to operate this unit properly before you use it. Failure to do so could result in serious injury. • Be sure to keep this manual handy so that you may refer to it later whenever any questions arise.
Safety Precautions ■ WORK GEAR AND CLOTHING ■ WARNINGS CONSIDERING HANDLING OF FUEL • When using your hedge-trimmer, always be sure to wear strong, durable, work clothing; shirts should be long-sleeved shirts and pants should be full-length pants reaching down to the ankles. • The engine of the RedMax hedge-trimmer is designed to run on a mixed fuel which contains highly flammable gasoline.
Safety Precautions ■ THINGS TO CHECK BEFORE USING YOUR HEDGE-TRIMMER ■ THINGS TO CHECK BEFORE STARTING UP THE ENGINE • Before beginning work, look around carefully to get a feel for the shape of the land, the trees, or hedges to be trimmed, and whether or not there are any obstacles which might get in the way while working, and remove any obstacles which can be cleared away before beginning work.
Safety Precautions ■ THINGS TO BE CAREFUL ABOUT WHEN USING YOUR HEDGE-TRIMMER • When using your hedge-trimmer, grip the handles of the hedge-trimmer firmly with both hands, place your feet slightly apart (slightly further apart than the width of your shoulders) so that your weight is distributed evenly across both legs, and always be sure to maintain a steady, even posture while working.
Safety Precautions ■ NOTES ON CARE AND MAINTENANCE OF YOUR HEDGE-TRIMMER • In order to maintain your hedge-trimmer in proper working order, perform the maintenance and checking operations described in this manual at regular intervals. In the event that any parts must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance.
Parts Location & Specifications 1. 2. 3. 4. 5. 6. 7. 8. Right handle Fuel tank Starter Left handle Throttle lever Ignition switch Throttle Cable Muffler 9. 10. 11. 12. 13. 14. 15. 16.
Emission Control Label IMPORTANT ENGINE INFORMATION INFORMATION IMPORTANTE CONCERNANT LE MOTEUR THIS ENGINE CONFORMS TO 2005 U.S. EPA REGULATIONS FOR SMALL NONROAD ENGINES. COMPLIANCE PERIOD : CATEGORY A ENGINE FAMILY : 5KZXS. 0254CD : EM ENGINE DISPLACEMENT : 23cc REFER TO OWNER’S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS. MANUFACTURED: KOMATSU ZENOAH CO. RedMax MADE IN JAPAN CE MOTEUR EST CONFORME A LA REGLEMENTATION U.S. EPA 2005 POUR LES PETITS MOTEURS HORS-ROUTE.
Set up ■ HT2200 1. Join the engine unit to the clutch housing of the cutter unit, with the fuel tank on the blade side. 2. Align the mounting holes and tighten the engine securely with the 3 screws. 5. Install the left handle to the bracket attached to the clutch housing. Use the hardware as shown below. 7. Cover the throttle cable with colgate tube. Connect the throttle cable and the switch wire. Hold the wires at the lower part of the handle using the tie band. 3.
Set up ■ CHT2200 1. Attach the engine to the clutch housing of the cutter unit. Casually fix the front 2 points with the screws(.55" long). 2. After connecting the ground wire, install the rear handle to the clutch housing with the screw(2" long) and the nut. 3. Put the screw(1.6" long) through the ground wire terminal and the rear handle, and in to the engine mounting base. Securely tighten all of the engine mounting screws. 4. Attach the front handle onto the gear housing and fasten with 2 screws(1.
Fuel WARNING • Gasoline is very flammable. Avoid smoking or bringing any flame or sparks near fuel. Make sure to stop the engine and allow it cool before refueling the unit. Select outdoor bare ground for fueling and move at least 3m (10ft) away from the fueling point before starting the engine. • The RedMax engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use.
Fuel again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture. 5. Put a clear indication on the outside of the container to avoid mixing up with gasoline or other containers. 6. Indicate the contents on outside of container for easy identification.
Operation ■ STARTING ENGINE WARNING 4. Rest the unit on a firm place. Pull the starter knob quickly. • Keep the blades clear of the surrounding as they will start moving upon starting of the engine. 1. When first starting up after putting fuel into the machine, push the priming pump until fuel runs out in the clear tube. Then close the choke. Choking may not be necessary when re-starting right after stopping the engine. NOTE 2.
Operation ■ STOPPING ENGINE 1. Release the throttle lever and run the engine at idling speed for a half minute. 2. Slide the ignition switch to the STOP position. NOTE • Except for an emergency, avoid stopping the engine while running it at high speed. ■ ADJUSTING IDLING SPEED 1. When the engine tends to stop frequently at idling mode, turn the idle set screw clock-wise. 2.When the cutting blades keep moving after releasing the throttle trigger, turn the idle set screw counter-clockwise.
Maintenance Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual. WARNING • Make sure that the engine has stopped and is cool before performing any service to the hedge-trimmer. Contact with moving cutting head or hot muffler may result in a personal injury. ■ DAILY INSPECTION • Check all the fasteners for loose or missing ones. • Brush off dirt on the blades and apply a light coating of oil.
Maintenance ■ MUFFLER WARNING • Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, do not use the hedge-trimmer and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire. ■ SPARK ARRESTER • The muffler is equipped with a spark arrester to prevent red hot carbon from flying out of the exhaust outlet. Periodically inspect and clean as necessary with a wire brush.
Maintenance ■ PROCEDURES TO BE PERFORMED AFTER EVERY 100 HOURS OF USE 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. Wipe away any carbon buildup on the muffler exhaust vent at the same time. 2. Tighten all screws, bolts, and fittings. 3. Check to see if any oil or grease has worked its way in between the clutch lining and drum, and if it has wipe it away using oil-free, lead-free gasoline.
Storage • Old fuel left in the carburetor can cause starting failure. Before storing the unit, empty the fuel tank and drain the carburetor with the priming pump equipped on it.
Parts List HEDGE-TRIMMERS HT2200 CHT2200 NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model name and the serial number are applicable to those specified in the parts list, then use parts number described in the parts list. 4.
Parts List Fig.
Parts List Fig.1 CUTTER GROUP — HT2200 Key# Description Part Number Q'ty 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Gear case Cover Gasket Drum Bearing Snap ring Pinion Bearing Gear comp. Rod Snap ring Fitting Felt Bolt Guide plate Upper blade Lower blade Screw(L:19) Screw(L:29) Washer Nut Screw Nut Cover, blade Handle comp. • Grip Washer Bolt Handle comp.
Parts List Fig.
Parts List Fig.
Parts List Fig.
Parts List Fig.3 CUTTER GROUP — CHT2200 Key# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 101 102 Description Gear case Cover Gasket Drum Bearing Snap ring Pinion Bearing Gear comp.
Parts List Fig.
Parts List Fig.4 ENGINE GROUP — CHT2200 Key# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 Description Cylinder Gasket, base Bolt, M5x22 Insulator Gasket, insulator Gasket, carb Screw, M5x20 Muffler assy • Muffler • Spark arrester Bolt, M5x50 Gasket, muffler Plate, muffler Screw, M4x16 Crancase comp.
RedMax LIMITED WARRANTY EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP.
RedMax Garantie limitée Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage défectueux pendant deux (2) ans à compter de la date initiale de livraison d’une unité.
KOMATSU ZENOAH AMERICA INC.