User guide

ManualsBrandsRedring ManualsLawn and GardenExpression 520M

APPLIED ENERGY PRODUCTS LIMITED, MORLEY WAY, PETERBOROUGH PE2 9JJ

TEL: +44 (0) 844 372 7761 / FAX: +44 (0) 844 372 7762

WEBSITE: www.redring.co.uk

We offer a technical advisory service on the telephone: Ring: 0844 372 7766

GUARANTEE AND CONTACT DETAILS

(A4) Leaflet No. 559-2333-03C

IMPORTANT:

This booklet should be left with the user after

installation and demonstration

WARNING:

Under no circumstances should this unit be connected

to the mains cold water supply

REDRING EXPRESSIONS 520

Manual and Thermostatic

Power Shower Units

Installation and User Guide

Summary of content (6 pages)

PAGE 1
GUARANTEE AND CONTACT DETAILS REDRING EXPRESSIONS 520 Manual and Thermostatic Power Shower Units Installation and User Guide IMPORTANT: This booklet should be left with the user after installation and demonstration APPLIED ENERGY PRODUCTS LIMITED, MORLEY WAY, PETERBOROUGH PE2 9JJ TEL: +44 (0) 844 372 7761 / FAX: +44 (0) 844 372 7762 WEBSITE: www.redring.co.uk We offer a technical advisory service on the telephone: Ring: 0844 372 7766 12 (A4) Leaflet No.
PAGE 2
Thank you for purchasing a quality Redring Expressions 520 Power Shower manufactured in England. CONTENTS Section Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to install your Expressions 520 Power Shower . . . . . . . . . . . . . . . . . . . . . . . . . . How to use your Expressions 520 Power Shower . . . . . . . . . . . . . . . . . . . . . . . . . . . . How to maintain your Expressions 520 Power Shower . . . . . . . . . . . . . . . . . .
PAGE 3
HOW TO INSTALL YOUR EXPRESSIONS 520 POWER SHOWER WHAT TO DO IF THINGS GO WRONG (1) SELF HELP If the shower is not working satisfactorily, make the following checks before calling out the installer. Any one of these adjustments could restore the performance. System will not operate Check that the mains electricity supply is switched on. Pump operates but no Check water is available to both ports, and that all isolating valves are open. water is delivered Check for an air-lock in the pump chamber.
PAGE 4
7. If you have not yet done so, remove the front cover assembly by undoing the retaining screws at the top and bottom of the unit. Remove Temperature Control Knob “B” Cap (see Diagram 10) by levering out carefully with a small flat bladed screwdriver and remove the small fixing screw as shown in Diagram 3. Your shower is provided with 4 fixing positions in the backplate (Diagram 11). The top-fixing holes are “key-hole” slots and the most convenient should be marked and drilled first.
PAGE 5
HOW TO USE YOUR EXPRESSIONS 520 POWER SHOWER 1. Ensure the electricity and water are turned on to the unit. 2. Your shower has 2 control knobs (Diagram 10). Knob “A” controls the Start/Stop operation and the water flow rate of the shower unit. Knob “B” controls the temperature of water and also incorporates a temperature limiter. 5. In all cases a dedicated cold water supply should be taken from the cold water cistern to the shower unit.
PAGE 6
7. Ø15mm copper pipe should be used. Ensure all burrs have been removed from the pipes before inserting into the push fit inlet ports. Diagram 7 illustrates the correct procedure for inserting and removing the pipes from the inlet ports. Take care to line up the inlet pipe correctly with the inlet port to avoid straining the internal “O”-Ring seal. DO NOT use solder fittings within 300mm of plastic fittings. DO NOT insert fingers into the push-fit inlet ports. Doing so could result in injury 8.