570 Pumped Electric Shower Installation instructions & User guide IMPORTANT: This booklet should be given to the customer after installation and demonstration. WARNING: Under no circumstances should this unit be connected to the mains cold water supply.
Thank you for choosing a quality 'Redring' product manufactured in Peterborough, England. CONTENTS Information for the user Important Safety Instructions How to use your 'Redring' shower How your 'Redring' shower works How to maintain your 'Redring' shower What to do if things go wrong Additional accessories Information for the installer Fixing the shower to the wall Plumbing Electrical Guarantee Knob 'A' Page Overheat Light 2 2 3 4 4 9 6 7 8 12 IMPORTANT SAFETY INSTRUCTIONS 1.
the option of reduced water flow. This option is mainly for summer usage and if this is used then knob 'B' must be re-adjusted. 8. When you have finished showering turn knob 'B' fully clockwise to the '• Stop' position. The motor will switch off and water will stop flowing. The 'POWER ON' light will also switch off. 9. Switch off the electricity at the ceiling switch or local isolator. Diagram 2 10.
temperature climbs above a set limit and the 'overheat' light will come on. This cut-out which gives an audible click, may also operate due to residual heat when the shower is switched off. It will reset itself if cold water is run through the shower for 10 to 20 seconds and the 'overheat' light will go out. 8. A pressure relief device is fitted to safeguard against extreme abuse conditions. 9. There are three defined plate spray settings adjustable by rotating the spray plate (see diagram 4).
b) Water too COLD c) Pump operates but no water is delivered d) Pump fails during shower Check power is on (indicated by 'power on' light). Decrease water flow by adjusting the temperature control (knob 'B') clockwise to a higher number on the temperature scale. Switch power to '• high power' setting. Select inner or outer spray patterns only . Water starvation. Stop pump immediately by turning knob 'B' fully clockwise to the '• Stop position'. Check the cold water cistern is full.
e) Water leaks from burst pressure relied valve Check for cause of high pressure and remove it. Blockage on outlet i.e: blocked spray plate etc. Replace the pressure relief disc. REDRING AFTER SALES SERVICE We offer a technical advisory service on the telephone to contractors and other customers with problems in the field. Ring 0870 9000 430 (Normal Office Hours) Spare parts can be supplied against any VISA or Access cards.
b) The heater must not be mounted in the direct spray from the handset. c) The handset must not be able to come into contact with the used water in the cubicle, bath or basin. If it can, even after the hose has been retained by the hose retainer (see diagram 12), then a vacuum breaker must be fitted. It should be noted that these devices are liable to minor leakage so they must be positioned so that any drips are not detrimental. 4. Fix the riser rail with screws provided.
6. The shower is designed to have an open outlet and should only be used with Redring recommended fittings. WARNING: DO NOT FIT A TAP ON THE SHOWER OUTLET. TAKE CARE TO AVOID RESTRICTING THE OUTLET OF THE PRESSURE RELIEF DEVICE. (SHOWN IN DIAGRAM 2). Diagram 8 Simply push in tube to attach A Tube is secured in position B Push in collet to release tube C 2. Cable Sizes Model Exp. 570 (8.5 kW) Exp. 570 (9.
5. A dual position cable clamp is provided. For top cable entry use retaining bar in horizontal position supplied. For bottom cable entry rotate retaining bar to the angled position. 6. WARNING: THIS APPLIANCE MUST BE EARTHED. 7.
ASSEMBLY OF RISER RAIL, HANDSET AND SOAP DISH Diagram 12 Additional knock out fixing slot if required Removable insert in soap dish for ease of cleaning 10 Locating Key
Guarantee We, GDA Applied Energy, guarantee that should this instant water heater prove to be defective by reason of faulty workmanship or material within 24 months (12 months outside the U.K.) of the date of purchase or commencement of hire purchase we will replace the defective parts FREE OF CHARGE on condition that: • The appliance has been correctly installed and used only on the supply circuit or voltage stamped on the rating plate.
