User manual

ManualsBrandsREELY ManualsModel Making LiPo Charger SystemsLiPo checker Suitable for batteries: 1 1 pc(s)

c) Battery safety

• Never damage the battery while measuring. Damaging the casing of the battery may cause

it to explode or catch re! Unlike conventional batteries (e.g. AA or AAA batteries) with a thin

sheet metal case, the case of the LiPo battery is made of a sensitive plastic lm.

• Never short-circuit the contacts of the battery. Do not throw the battery or the product into re.

This may cause a re or explosion!

Product overview

MOLEX

2.0 mm port

MCX

1.25 mm port

JST

2.54 mm port

MCPX

2.0 mm port

Operation

• Connect the battery to the battery tester. To do this, use the appropriate connector plug for your battery.

Pay attention to the correct orientation when doing so. Never use force when connecting a plug. Doing so

could damage the product.

• The remaining battery voltage is shown on the LE display. Only voltage values within the input voltage

range are displayed. In the event of a low voltage <3.3 V, the display ashes. In the event of an excess

voltage >4.35 V, no message is displayed.

• Never connect several batteries to the connections at the same time.

• Remove the tested battery before testing another battery with a different plug connector.

Do not measure at voltages higher than 4.35 V! This will damage the product.

Care and cleaning

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may damage the

casing or cause the product to malfunction.

• Use a dry, lint-free cloth to clean the product.

Disposal

Electronic devices are recyclable waste and must not be placed in household waste. At the end

of its service life, dispose of the product according to the relevant statutory regulations.

Remove any connected battery and dispose of it separately from the product.

You thus full your statutory obligations and contribute to protection of the environment.

Technical data

Input voltage range ..............................2.5 to 4.35 V

Display unit ..........................................V

Power consumption .............................0.05 W

Accuracy ..............................................3.65 V>>0.01 V; 4.2 V>>0.01 V, 4.35 V>>0.01 V (±10 mV)

Usable .................................................1 cell

Display .................................................0.36” LED (22 x 14 mm)

Connections ......................................... JST (2.54 mm), MCPX (2.0 mm), MCX (1.25 mm), MOLEX (2.0 mm)

Dimensions (W x H x D) .....................60 x 34 x 17 mm

Weight .................................................14 g

Operating instructions

LiPo Checker 1S

Item no. 1719875

Intended use

The product is intended to be used for fast and precise measurement and display of the charging state of

lithium batteries in volts. The product can test LiFe 3.3 V/LiPo 3.7 V/Li-Hv 3.8 V batteries. Measure and

connect only one battery in each case.

This product is intended for indoor use only. Do not use it outdoors. Contact with moisture (e.g. in bathrooms)

must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. Using the product for

purposes other than those described above may damage the product. In addition, improper use can cause

hazards such as a short circuit or re. Read the instructions carefully and store them in a safe place. Only

make this product available to third parties together with its operating instructions.

This product complies with statutory, national and European regulations. All company and product names are

Delivery content

• Battery tester (for lithium batteries)

• Operating instructions

Up-to-date operating Instructions

Download the up-to-date operating instructions at www.conrad.com/downloads or scan the QR code shown.

Follow the instructions on the website.

Explanation of symbols

The symbol with an exclamation mark in a triangle is used to highlight important information in

these operating instructions. Always read this information carefully.

The arrow symbol indicates special information and advice on how to use the product.

Safety information

Read the operating instructions and safety information carefully. If you do not follow the

safety information and information on proper handling in these operating instructions,

we will assume no liability for any resulting personal injury or damage to property. Such

cases will invalidate the warranty/guarantee.

a) General information

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may become dangerous playing

material for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,

moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and protect it

from any accidental use. Safe operation can no longer be guaranteed if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height may

damage the product.

• Always observe the safety information and operating instructions of any other devices which

are connected to the product.

• Consult a technician if you are not sure how to use or connect the product, or if you have

concerns about safety.

• Maintenance, modications and repairs may only be carried out by a technician or a specialist

repair centre.

• If you have questions which remain unanswered by these operating instructions, contact our

technical support service or other technical personnel.

• Always comply with the accident prevention regulations for electrical equipment when using

the product in commercial facilities.

• In schools, educational facilities, hobby and DIY workshops, measuring devices must be

operated under the responsible supervision of qualied personnel.

b) Persons and product

• Never use the product immediately after it has been brought from a cold room into a warm

one. The condensation that forms might destroy the product. Allow the product to reach room

temperature before connecting it and putting it to use. This may take several hours.

• Never overload the product. Observe the technical data.

• Never operate the product with wet hands.

• Never cover the product during use.

• Keep the product away from ignition sources or naked ames, do not smoke while handling

and using the product.

• The product may not be used in the vicinity of ammable materials or gases.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming or capturing in

electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is

prohibited. This publication represents the technical status at the time of printing.