Table of Contents EN 1. Precaution.........................................................................2 2. Preparation....................................................................... 5 Standard Accessories...................................................5 Part Names.................................................................... 6 Start the Image Copier................................................. 8 3. Place Film Into The Holder.......................................... 10 4.
Welcome Thank you for purchasing a reflecta x120. Please take a moment to read through this manual. Its contents will send you on an educational journey into your copier multiple capabilities. 1. Precaution Before using reflecta x120, please ensure that you read and understand the safety precautions described below. Always ensure that the reflecta x120 is operated correctly. Never operate reflecta x120 inside of an aircraft or anywhere else where operation of such devices is restricted.
If you notice smoke or a strange odor coming from reflecta x120, turn the power off immediately. Take the reflecta x120 to the nearest authorized service center for repairing. Never attempt to reflecta x120 on your own. EN Use only the recommended power accessories. Use of power sources not expressly recommended for reflecta x120 may lead to overheating, distortion of the equipment, fire, electrical shock or other hazards. reflecta x120 may become slightly warm during use.
FCC Notice This equipment has been tested and found to comply with the limits for a Class B Digitize device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instruction, it may cause harmful interference to radio communication.
2.
Part Names EN -6-
Note: We suggest using bundled brush to insert into reflecta x120 slot and clean the glass surface periodically to produce a clear image. Please make sure your film Holder and cover tray are clean before inserting into the reflecta x120 as well. Dust or dirt from the film and cover tray will affect the quality of your scanned images.
Starting the reflecta x120 EN Connecting Electric Power to the Copier (a) From Computer USB port: Plug the USB mini B of the supplied USB cable to the USB port of the copier, and plug the other USB end into the USB port of your computer/notebook. (b) From Power Adaptor: Plug the USB mini B of the supplied AC adaptor to the USB port of the copier, and plug the adaptor to the power outlet.
Insert SD Card Into The SD Card Slot The golden prints of the card facing upward when insert into the card slot. Push with a slight force, the card will automatically lock when it is in the right position. Push once again will unlock the card. Turn on the power of the Copier: After the electric power is connected, lift up the top cover, press the Power On / OFF Button to turn on the scanner for scanning film The blue LED and the LCD screen will be lighted and ready for film scanning.
3. Place the film Into The Holder 1. Keep the glossy surface of the film in the upward direction. Open the film holder as Illustrated. 2. Put the 120 reversal / negative / B&W film into the holder as shown. 3. Close the holder and please make sure the holder close properly.
4. Using the reflecta x120 EN Press Power button to power on the unit. Press Power button to power off if you do not want to use the reflecta x120. 1. Insert the loaded film holder properly into the slot according to the ▲ or ● sign shown on the reflecta x120 and film holder.
You can adjust the location of the film by moving the film holder; the film holder can be moved in both directions. Keep your picture in the rectangular white frame, improper adjustment of picture may copy the extra edges of the film. You may crop away the extra edges later by the software. (please refer to page 27 edit the pictures section 1.4 crop) To select film type: Press the Type Button for selecting the type of film.
Note: Improper selection of Film type may not get good result. (2) Press Copy button to convert picture to Digital image. To get the best Digitize image wait for the image display on the LCD screen to adjust the brightness until it becomes stable. It normally take 3~4 seconds, depending on the brightness of your film. Note: For safety purpose the copier will automatically turn to OFF condition if you are not using it for more than 10 minutes.
Moving the film holder for next scan Move the film holder forward for the next scan as shown below -14- EN
Choosing the best Exposure for the film The exposure of the copier is set automatically, it normally does not need any adjustment. In some occasion you need to adjust the brightness (exposure) at your main subject. Press EV/Delete button to adjust expose value. Press Up or Down Button to adjust the exposure compensation from +2EV to -2EV in 0.5 EV increments. The amount of compensation is shown at the bottom of the LCD. Press EV/Delete button to confirm the exposure compensation.
EN 5. Playback Mode 1. Press Playback button for reviewing Digital image. 2. Press UP button to forward reviewing. Press DOWN button for backward reviewing. 3.
4 Press Playback button again to go back to original screen.
EN 6. Delete Mode 1. Under Playback Mode Press Delete button once then OK button to delete current image stored in the card. 2. Press Delete button twice then OK button to delete all images stored in the card. 3. Press Delete button three times then OK button to format SD card. 4. Press Delete button again will go back to the playback Mode Note: a. Formating SD card will delete all the files in the card. Download your files in the SD card into your computer before the SD card is formatted. b.
EN 7. Install the Software Installing the Software in Windows OS computer 1. Insert the installation CD into the CD-ROM drive and the installation CD menu should appear. 2. When you see the following screen, choose “ArcSoft MediaImpression” to install the software. 3. Follow the on-screen instructions. 4. On Customer Information, please refer to the sticker with SN no. on the CD paper cover for License Key. 5. The installed software will automatically create a MediaImpression logo on your desktop. 6.
Installing the Software in Mac OS computer 1. Insert the installation CD into your computer’s CD-ROM drive and click CD icon. 2. Click” MediaImpression Installer” 3. Follow the on-screen instructions. 4. On Customer Information, please refer to the sticker with SN no. on the CD paper cover for License Key.
8. To Link the Card to Computer 1. Plug the USB cable to copier and computer properly. EN 2. Turn power on. 3. Press the Up button to select “SD to PC” to YES, then press the OK button for confirmation.
4. To active bundled software-MediaImpression, the images saved in SD card will be import to you computer automatically for reviewing. Please copy the images from SD card to the designated folder or album of your computer.
Note: EN Bundled MediaImpression is only for images editing purpose. The Acquire function is for Film Scanner/ Photo Scanner without TFT display.
9. Viewing Images from TV Connect your copier to the HDTV by the USB cable. The copier only support to those HDTV model with USB link. 1 2 3 4 Turn on the HDTV set and select USB link from the HDTV set (See section of USB link in HDTV manual). Turn on the power of the Copier and select YES for TV connection, and the LCD will turn OFF For operating the playback/review images on the TV screen, please refer to the operation of USB link (U-link).from the HDTV manual.
EN 10. Edit The Pictures First, click on the picture to select, and then use the ArcSoft MediaImpression tools to edit the pictures as you like. Edit Photo Editing Tools The Photo Editing Tools module includes a complete set of photo enhancement, editing and retouching controls. The windows can be stretched to provide a large size view of the active photo. Double click the module’s tool bar to maximize the window to fill the computer screen.
EN 1.2 Color This feature is designed to fix Digitize photos that have unnatural color or appear too dark. It’s also great for fixing scanned versions of old prints that have faded or whose colors have changed after many years. How to fix the color of a photo: 1. Drag the color balance sliders to make the photo color appear more natural. Add red or yellow to make the photo warmer. Add blue or green to make the photo cooler. 2.
2. Drag the small white box inside the zoom navigator to move over a red eye. 3. Place your cursor directly over the red eye and click. 4. Repeat the process until all the red eyes are fixed. 5. Click “Undo” if you make a mistake or don’t like the result. 1.4 Crop This feature enables you to trim photos for a dramatic effect or cut off the distracting parts of a picture. How to use the crop function: 1. Choose the crop orientation (portrait or landscape). 2.
EN How to use Straighten: 1. Move the slider (or click the rotate buttons) until the photo appears straight. 2. Use the superimposed grid lines for vertical and horizontal reference. 3. Click “Apply” if you like the result. Click “Cancel” if you do not. 1.6 Blur Background This feature can be used in subtle way – to tone down un-important background details, or for dramatic effect- by making the main subject of a photo “pop out” of the picture. How to use the Blur Background function: 1.
2. Retouch 2.1 Healing Brush The Healing Brush is good for fixing dust, scratches and removing skin blemishes. How to use the Healing Brush to fix a skin blemish: 1. Establish a source point for the Healing Brush by holding the Shift key and clicking on an area of the skin that is close in color and texture to the area you want to heal. 2. Use the zoom control to zoom in on the blemish. 3. Adjust the size of the healing brush so the cursor (circle) is only slightly larger than the blemish. 4.
3. Click and hold your mouse button and carefully paint over the telephone pole. Do not release the mouse button until the job is done. The sky will be cloned into place. 4. Click “Undo” if you make a mistake or don’t like the result. EN 2.3 Lighten/Darken The Light/Darken tool is good for adjusting specific areas of a photo. 2.4 Smudge Simulate the smearing of wet paint. Please click and drag the sliders below to change the brush size and sharpness. 2.5 Sharpen Sharpen blurry areas.
2.7 Paint Brush Allows you to “paint” on your image when you click and drag the mouse. Click and drag the sliders below to change the brush size and transparency. 2.8 Line Draw a straight line in the photo. Click and drag the sliders below to change the line width and transparency. 2.9 Eraser Simulate an eraser, removing the image painting by paintbrush and line tools from your photo. Click and drag the sliders below to change the eraser size and effect. 3.
11. Appendix EN Specifications Image Sensor Preview and Review Lens Specification 1/2.3” 14 Mega CMOS Sensor, 2.4” Color LCD Display F/No. 5.6, 5 elements Aspheric hybrid lens Color Balance Automatic Exposure Control Automatic & Manual adjustment Support Film Size 120 Film: Auto Cropping 6X9/6X8/6X7/6X6/6X4.5 cm Support Film Type 120 Color Reversal Film (REV) Auto Converting 120 Color Negative Film (NEG) 120 B&W Negative Film (B&W) Focusing Fixed Focus EV adjustment Yes, + - 2.0 EV PC Interface USB 2.
Icons & Indicators 6X9, 6X8,---645 REV NEG B/W Film size Selected Playback Mode Delete One Delete All Slide Show Format SD Card Wait Yes Reversal film (Transparent film) No Negative Film Card Error B/W Negative Film PC-SD-Card Selection PC-SD Card Link-connect ed Card Full Card Lock HDTV (USB) Connection EV Compensation Indicator EV Compensation Available number take in SD card -33-
PC System Requirements z Intel® Pentium® P4 1.6GHz or equivalent AMD Athlon z Free USB2.0 port z 512MB RAM z 500MB free hard disk space z 1024 x 768 pixel color monitor z CD-ROM drive z Windows® XP Service Pack II / Vista™, 32/64 bits Windows 7/Windows 8 Mac System Requirements z PowerPC G5 or Intel Core Duo processor recommended z Free USB2.0 port z 768MB RAM z 500MB free hard disk space z 1024 x 768 color monitor z CD-ROM drive z Mac 10.5 ~ 10.