Walk Thru Gate MODEL NO: 1158, 1160, & 1165 Owner’s Manual 11/25/2013_BL READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE USE. www.regalo-baby.com ........................................................................... Regalo International, LLC.
Assembly and Installation Instructions Read and follow all instructions carefully to ensure that your gate and extensions are properly installed. Improper installation could result in the gate becoming unstable or dislodged from the doorway. Always make sure the extension is securely attached to the gate before using. The safety of your child is your responsibility. Please keep these instructions for your reference. NOTE: • Never use more than two extensions per gate.
Check to make sure you have all of the parts shown: B. C. A. D. A. Gate Frame B. 4 Wall Cups C. 4 Screws (requires a Phillips/crosshead screwdriver) D.
Extensions List NOTE Item NO. 12 6 8 4 MAX Size 1158 29--58 inches 1160 1165 29--40 inches 29--44 inches NOTE: When installing any gate at its maximum width use Wall Mounting Cups to ensure stability and safety.
Assembling and Installing Your Gate **Note: IMPORTANT!! You will notice a slight gap between the gate door latch and the frame. THIS IS NOT A DEFECT. Your gate is a pressure mounted gate and this gap will disappear once you tighten your gate in its opening. Step 1. Locate the 4 threaded spindle rods. Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot. Threaded Spindle Rod Diagram A Adjustment Wheel Rubber Foot Step 2.
Step 3. Position the gate so that it is level and centered within your doorway or opening. Rotate the adjustment wheels on the threaded spindle rods in the opposite direction at in Step 1, expanding the gap between the rubber foot and the adjustment wheel. Expand each of the 4 Threaded Spindle Rods until they make contact with the doorway or opening. Do not fully tighten the Threaded Spindle Rods yet.
Step 4. When you are satisfied with the general placement of your gate, fully tighten the Threaded Spindle Rods attached to the lower corners of the gate by further rotating the Adjustment Wheels. Continue by tightening the upper Threaded Spindle Rods. As you tighten the upper Threaded Spindle Rods, you will notice the gap between the Door Frame and the Easy Open Latch begin to narrow.
Positioning and Attaching the Wall Cups Your gate is a pressure mounted gate. Therefore, it is not necessary to use the screw attached Wall Cups in your door opening if you choose not to. However, IF YOU ARE USING THE GATE AT THE TOP OF STAIRS YOU MUST USE THE WALL CUPS. Using the Wall Cups will affix your gate more firmly in the doorway or opening. Step 1.
Step 3. With the gate fully removed, you can now use the circles you marked during Step 1 as guides for screwing in your 4 Wall Cups. Center each of the Wall Cups within the guide circles and use the provided self-tapping screws to fasten them in place via the hole through the center of each Wall Cup. Diagram F Step 4.
Operating the Door Latch Step 1. Pull the Spring Lock away from the Easy Open Latch while simultaneously lifting the Lock Lever upwards. This will release the Locking Latch from the Gate Frame and allow the door to push or pull open. Spring Lock Lock Lever Diagram H Step 2.
Adding a Gate Extension Step 1. Assemble the gate per the gate instructions. Step 2. Choose the side of the gate to be extended and remove the top and bottom Threaded Spindle Rods. Step 3. Assemble the gate and extension as illustrated. Step 4. Reposition the gate and fit in accordance with the gate fitting instructions.
Care And Maintenance Periodically check the gate for signs of damage, wear, or missing components. Do not use if any part is missing, worn or damaged. Check the gate regularly to ensure all the hardware and mountings are tightened. Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.
Replacement Parts Available In the event of any damage or breakage, the following replacement parts are available for order by contacting Regalo Customer Service. Wall Cups 1” Wall Mount Screws (#10001) (#14015) Threaded Spindle Rods with Adjustment Wheel (#14016) Bottom Plug Insert (#14019) Easy Open Latch (#13037) Top Plug Insert (#14020) Contact Regalo for questions and replacement parts. For questions about the use of your gate, call our customer care line 866-272-5274.
Regalo International, LLC.
