1/22/2013_BL Easy Open Extra Wide Gate MODEL NO: 1185 Owner’s Manual READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. KEEP INSTRUCTIONS FOR FUTURE USE. www.regalo-baby.com ........................................................................... Regalo International, LLC.
Assembly and Installation Instructions Please read these instructions carefully before installing your gate. WARNING: Intended for young children aged 6 months through 24 months. Check the gate regularly to see if all the hardware and mountings are tightened. To prevent serious injury or death, securely install gate or enclosure and use according to manufacturer’s instructions. Never use with a child able to climb over or dislodge the gate or enclosure. Never leave child unattended.
Check to make sure you have all of the parts shown: A. B. D. E. A. Easy Open Gate B. 6” Extension C. 12” Extension D. 4 Threaded Spindle Rods E. 4 Wall Mounting Cups F. 4 Screws (requires a Phillips/crosshead screwdriver) 1 C. F.
Assembling and Installing Your Gate **Note: IMPORTANT!! You will notice a slight gap between the gate door and the gate frame. THIS IS NOT A DEFECT. Your gate is a pressure mounted gate and this gap will disappear once you tighten your gate in its opening. Step 1. Locate the 4 threaded spindle rods. Rotate the adjustment wheels along the threading, eliminating the gap between the adjustment wheel and the rubber foot. Threaded Spindle Rod Diagram A Adjustment Wheel Rubber Foot Step 2.
Step 3. Position the gate so that it is level and centered within your doorway or opening. Rotate the adjustment wheels on the threaded spindle rods in the opposite direction as in Step 1, expanding the gap between the rubber foot and the adjustment wheel. Expand each of the 4 Threaded Spindle Rods until they make contact with the doorway or opening. Do not fully tighten the Threaded Spindle Rods yet.
Step 4. When you are satisfied with the general placement of your gate, fully tighten the Threaded Spindle Rods attached to the lower corners of the gate by further rotating the Adjustment Wheels. Continue by tightening the upper Threaded Spindle Rods. As you tighten the upper Threaded Spindle Rods, you will notice the gap between the Door Frame and the door begin to narrow.
Positioning and Attaching the Wall Cups Your gate is a pressure mounted gate. Therefore, it is not necessary to use the screw attached Wall Cups in your door opening if you choose not to. However, IF YOU ARE USING THE GATE AT THE TOP OF STAIRS YOU MUST USE THE WALL CUPS. Using the Wall Cups will affix your gate more firmly in the doorway or opening. Step 1.
Step 3. With the gate fully removed, you can now use the circles you marked during Step 1 as guides for screwing in your 4 Wall Cups. Center each of the Wall Cups within the guide circles and use the provided self-tapping screws to fasten them in place via the hole through the center of each Wall Cup. Diagram F Step 4.
Operating the Door Latch Step 1. Use your thumb or forefinger to pull back on the Thumb Lock. This action will release the locking pin below the metal saddle that joins the door and the gate frame. Step 2. With the Thumb Lock pulled back, lift up on the entire door panel, raising the gate high enough for the upper and lower metal saddles to clear free of their counterparts. Your gate door should now be free to fully open. To close the gate, simply repeat these steps in reverse.
Adding a Gate Extension Step 1. Assemble the gate per the gate instructions. Step 2. Choose the side of the gate to be extended and remove the top and bottom Threaded Spindle Rods. Step 3. Assemble the gate and extension as illustrated. Step 4. Reposition the gate and fit in accordance with the gate fitting instructions.
Replacement Parts Available In the event of any damage or breakage, the following replacement parts are available for order by contacting Regalo Customer Service. Wall Cups (#14015) 1” Wall Mount Screws (#10001) Threaded Spindle Rods with Adjustment Wheel (#14016) Bottom Plug Insert B Tapered Round Insert (#14041) (#14042) Untapered Round Insert (#14043) Contact Regalo for questions and replacement parts. For questions about the use of your gate, call our customer care line 866-272-5274.
Regalo International, LLC.
