06/21/2013_DC FOR THE MOST IMPORTANT PEOPLE IN THE WORLD CONVERTIBLE CRIB RAIL INSTRUCTIONS Model: 2015 www.regalo-baby.com ........................................................................... Regalo International, LLC.
WARNING: IMPORTANT ! KEEP FOR FUTURE REFERENCE ! • Failure to follow these instructions for the assembly and use of your crib rail could result in serious injury or death. • This crib rail is intended for use with children 2 years to 5 years of age. WARNING: SUFFOCATION AND STRANGULATION HAZARD -Gaps in and around crib rails have entrapped young children and killed infants. -NEVER use with children younger than 2 years old. Use ONLY with older children who can get in and out of toddler bed without help.
PART LIST : 1. Crib Rail Mesh Wall 2. Right Upper Support Bar 3. Left Upper Support Bar 4. Right Bottom Support Bar 5. Left Bottom Support Bar 6. Right Under Bar 7. Left Under Bar 8. Right Anchor and Strap 9.
CRIB RAIL ASSEMBLY AND SET UP Step 1 : Remove crib rail from packaging and set all parts out in front of you. Step 2 : Insert Left Upper Support Bar into Left Bottom Support Bar. Make sure the spring pin fits securely into opposing hole so that the two pieces cannot pull apart. (Diagram A1) Step 3 : Repeat Step 2 directions to assemble the right side of the crib rail. (Diagram A2) (Diagram A1) (Diagram A2) Step 4 : With the left and right sides of the crib rail assembled, connect the two sides.
Frame assembly should look like the image below. (Diagram B2) (Diagram B2) Step 5 : To install the mesh wall on the crib rail, slide the mesh wall over the frame until it reaches the other end and zip it shut to complete the installation. (Diagram C1) NOTE : If the zipper does not close securely, make the necessary adjustments to ensure proper closure.
Step 6: With the wall of the crib rail completely assembled, you will now connect the remaining legs with the anchor straps. (Diagram D1) (Diagram D1) Spring button Spring button (Diagram D2) (Diagram D3) Step 7: Insert one side of the wall frame into one of the leg pieces. Press in the metal spring button to fully insert the tube into the hole in the plastic hinge. (Diagram D2) The spring button should line up with the access hole in the plastic sleeve on the hinge.
MOUNTING THE CRIB RAIL TO THE CRIB Note : The next steps may require the help of a secondary person. Step 1: Make sure that you have configured your convertible crib into its toddler bed configuration, and the crib mattress has been removed. Then, place the crib rail atop the mattress support structure so that it is poitioned to create a barrier across the opening of your convertible crib. (Diagram E1) You may need to release the strap locking buckles located on the under side of the plastic hinges.
(Diagram E2) Step 2: Once the crib rail is properly placed, check to make sure the left and right Guide Bar Assemblies are parallel to one another. Then, place the mattress on top of the assembly.
WARNING : In order for the crib rail fabric wall to be firmly held against the side of the mattress you MUST properly tighten the anchoring straps. Please follow the directions below very carefully. Step 3 : Tighten the straps to bring the crib rail into it’s proper position. To tighten the straps, first release the strap locks on the under side of the Left and Right Under Bars. Pull the straps towards you until all the excess slack has been pulled out from under the mattress.
OPERATION OF SWING DOWN FEATURE (Diagram F) Step 1: With the crib rail side in the ‘up’ position, locate the locking tab on each of the hinges. (Diagram F) A close up view of the hinge is shown in (Diagram G1). Step 2: Once the locking tabs have been located, flip the tab up to expose the open side of the lock. (Diagram G2)This will allow the upper part of the crib rail to move freely.
Step 3 : With both locking tabs turned to the ‘open’ position, hold the upper part of the crib rail firmly and swing it down. (Diagram H1) The crib rail should now be in the ‘down’ position. (Diagram H2) NOTE : To return the crib rail to the ‘up’ position, reverse the previous instructions. IMPORANT: Make sure that the crib rail is in the ‘up’ position and the locking tabs are securely closed before leaving a child alone in the bed.
CARE AND MAINTENANCE Periodically check the crib rail for signs of damage, wear and/or for missing components. Do not use if any part is missing, worn or damaged. Check the crib rail regularly to make sure all hardware and mountings are tight and secure. Do not use abrasive cleaners or bleach when cleaning. Proper cleaning of crib rail can be done by sponging it with warm water and mild detergent.
COPYRIGHT 2013 Regalo International, LLC.
