• Style that revolves around you. CEILING FAN OWNER'S MANUAL • READ AND SAVE THESE INSTRUCTIONS • REGULATOR • 09/08 WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
GENERAL INSTALLATION & OPERATION INSTRUCTIONS IMPORTANT SAFEGUARDS: 1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
IMPORTANT SAFETY PRECAUTIONS Thank you for choosing a Regency Ceiling Fan. You have chosen the best! Your new ceiling fan has been designed to provide many years of service and enjoyment. Warnings: • Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting. • Support directly from building structure. • To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked "Acceptable for Fan Support of 22.7 kg (50 lbs.
UNPACKING YOUR FAN 1. Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. 2. Examine all parts. You should have the following: 2 8 12 3 1 4 13 5 9 6 10 11 7 14 1. Fan blades (5) 2. Mounting bracket 3. Hanging bracket 4. Ceiling canopy 5.
PREPARATION Parts identification on assembled fan Canopy Downrod Blade Collar Cover Motor Housing Blade arm Pull chain with fob Detachable Switch Housing PREPARATION: Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box.
INSTALLING THE MOUNTING BRACKET AND HANGING BRACKET Caution: To avoid possible electrical shock, be sure electricity is turned off at the main power box before wiring. All wiring must be in accordance with National and Local Electrical Codes and the ceiling fan must be grounded as a precaution against possible electric shock. Outlet box IMPORTANT NOTE: THIS CEILING FAN EXCEEDS THE MAXIMUM WEIGHT (35 LBS) SPECIFIED BY UL FOR HANGING FROM A STANDARD CEILING FAN RATED OUTLET BOX.
INSTALLING THE FAN 1. Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out) facing upward. 2. Loosen the two set screws and remove the downrod pin and cotter pin from the top coupling of the motor assembly. 3. Remove ball from the downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove ball. 4.
INSTALLING THE FAN CONTINUED WARNING: To avoid damaging the blade arms and blades, do not install them onto fan until fan is fastened to ceiling. 1. Lift ball/downrod/fan into hanging bracket opening. NOTE: The tab opposite hanging bracket opening should fit in slot on ball. Tab Slot ELECTRICAL CONNECTIONS * Be sure electricity is turned off at the main power box before wiring. 1. Four wires are connected to the fan. Black - this is the "hot" power to run fan.
FINISHING THE INSTALLATION 1. Tuck connections neatly into ceiling outlet box. 2. Slide the canopy up to ceiling and over the 2 screws on the hanger bracket. Rotate canopy clockwise. Next, while holding the canopy with one hand, slide the canopy screw cover plate over the screws and rotate clockwise until tight. NOTE: adjust the canopy screws as necessary until the canopy and canopy screw cover plate are snug.
INSTALLATION OF DETACHABLE SWITCH HOUSING MOUNTING HUB 1. Remove one of the three screws on the mounting hub located on the fan motor. 2. Loosen the other two screws. 3. Install detachable switch housing mounting hub to mounting hub. 4. Pass the 2 light wires through the center hole of the detachable switch housing mounting hub. 5. Line up the two slotted holes with the two loose screws on the mounting hub located on fan motor. 6. Re-install the third screw removed and tighten all three.
INSTALLING THE REMOVABLE SWITCH HOUSING NOTE: Be sure the power is off before installing. 1. Loosen the 3 side screws on detachable mounting plate halfway. 2. If installing light kit, carefully remove light kit cover in bottom of switch housing. Attach the light kit to the switch housing per instructions supplied with light kit. (Follow the instructions included with the kit.) 3. Connect the plug and receptacle and make sure side buckle snaps in place. 4. Attach the switch housing to the mounting plate. 5.
OPERATION Turn on the power and check operation of the fan. The fan is controlled by the use of the pull chain as follows: one pull = high speed two pulls = medium speed three pulls = low speed four pulls = off For proper functions, ensure that the chain is pulled down fully and released each time. NOTE: Leave pull chain switch in "high speed" position when using optional wall control. The slide switch on the side of the switch housing controls forward or reverse rotation.
CARE AND CLEANING Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound during operation. This is especially true in climates with broad temperature and humidity ranges. When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. If you experience any flaws in the operation of your fan, please check the following points.
