Style that revolves around you. • CEILING FAN OWNER’S MANUAL • • STRASBURG • 11/05 WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
GENERAL INSTALLATION & OPERATION INSTRUCTIONS IMPORTANT SAFEGUARDS: 1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
IMPORTANT SAFETY PRECAUTIONS Thank you for choosing a Regency Ceiling Fan. You have chosen the best! Your new ceiling fan has been designed to provide many years of service and enjoyment. Warnings: • Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting. • Support directly from building structure.
UNPACKING YOUR FAN 1. Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. 2. Examine all parts. You should have the following: 1 8 15 2 9 3 10 10” 6” 4 11 5 16 12 6 13 7 HI U/L MED D/L LOW FAN OFF OFF 5GM 17 18 19 20 5GM REV ON 14 1. 2. 3. 4.
PREPARATION Parts identification on assembled fan Canopy Downrod Fan Housing Glass Shade Blade Blade Arm PREPARATION: Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box. Do not lay motor housing on its side as this could result in shifting of motor in decorative enclosure.
INSTALLING THE FAN 1. Carefully support fan housing (motor) in its styrofoam packing with the mounting collar (where the wires come out) facing upward. 2. Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove ball. 3. Attach glass w/screws to the top of the motor housing. 4.
INSTALLING THE FAN HANGING THE FAN WARNING: To avoid damaging the blade arms and blades, do not install them onto fan until fan is fastened to ceiling. 1. Lift ball/downrod/fan into hanging bracket opening. NOTE: The tab opposite hanging bracket opening should fit in slot on ball. 2. Make wire connections, (refer below to “Electrical Connections”). 3. Slide canopy up and fasten to hanging bracket with 4 screws provided.
REMOTE CONTROL GENERAL INFORMATION Multiple code choices are included with your fan’s remote control in case: • you have more than one remote control fan and want them to respond only to their own remote control • you have other radio controlled devices in your home that may interfere with the fan remote control (i.e.
ELECTRICAL CONNECTIONS Five wires are connected to the fan Black - the “hot” power to run fan. White - the “common” power to run fan and light, also referred to as “AC neutral”. Blue - power for light. Orange - power for uplighting Green - ground wire. WH BLK WH Green BLK ELECTRICITY IS TURNED OFF AT THE BE SURE ground FAN MAIN POWER BOX BEFORE WIRING. Green ground switch WH RED Connect six power wires as shownGround [Fig. 1], to using wire nuts downrod on mounting bracket provided.
BLADE & BLADE ARM ATTACHMENT 1. Place washer on screw. Insert this assembly through the blade and start the screw into the blade arm. Repeat this procedure without tightening the screw until all 3 screws have been started into the blade arm (Fig. 1). Screw Washer 2. Tighten each screw, starting with center screw. Blade 3. Fasten blade assembly to motor with Blade Arm provided screws and metal lockwashers (Fig. 2). repeat procedure for remaining blades.
INSTALLATION OF DETACHABLE SWITCH HOUSING NOTE: Be sure to turn of the power before installing. 1. If installing a light kit, attach to switch housing per instructions supplied with light kit. See “Electrical Connections” for hook-up of light kit. Carefully remove kit plug in bottom of switch housing. 2. If not already installed, install detachable switch housing mounting hub. Remove only one screw and loosen the other two only. Install detachable switch housing mounting hub and re-install screw.
OPERATION OPERATING BUTTONS ON THE TRANSMITTER HI – fan high speed MED – fan medium speed LOW – fan low speed FAN/OFF – fan speed off LIGHT – light brightness and off function for uplight, and one for downlight FOR/REV – forward and reverse • The light functions are controlled by pressing the light button. Hold button down to increase or decrease light brightness. Tap button quickly to turn light off or on for either uplight or downlight.
CARE AND CLEANING Periodic cleaning of your new ceiling fan is about the only maintenance that is needed. Only use a soft brush or lint free cloth to avoid scratching the finish. DO NOT use water when cleaning your ceiling fan. It could damage the motor or the wood blades, and/or create the possibility of electrical shock. NOTE: Periodically it may be necessary to re-tighten blade screws to prevent clicking or humming sound during operation.
THANK YOU FOR PURCHASING A REGENCY CEILING FAN. Write to us at: Regency Ceiling Fans P.O. Box 730 Fenton, MO 63026 For additional troubleshooting tips, visit us on the Web at: www.regencyfan.
