Instructions / Assembly

ManualsBrandsRegency ManualsFurnitureLegacy 168 in. Java Modular Racetrack Conference Table with Power Data Grommet

Parts: Quantity will vary with model.

A: End Leg B: Center Leg

Quantity: 2

H: Thumb

Screws

I: Flat

Bracket

D: Stringer

F: Cord Holder

G: EClip Bracket

IMPORTANT NOTICE:

Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid scratching the parts.

Check to be sure that you have all parts and hardware.

Remove all wrapping materials, including staples & packing straps before you start to assemble.

Keep all hardware parts and packaging out of reach of children.

Any problems or questions call Regency Ofce Furniture at 1-866-816-9822

C: Round End

Legacy Modular Conference Table • INSTRUCTIONS

(LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652,

LCTRT24052, LCTRT26452, LCTRT28852)

Organize your parts. You may need a rubber mallet.

E: Center Piece

Hardware: Quantity will vary with model.

J: DPEL

Summary of content (5 pages)

PAGE 1
Legacy Modular Conference Table • INSTRUCTIONS (LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652, LCTRT24052, LCTRT26452, LCTRT28852) Organize your parts. You may need a rubber mallet. Hardware: Quantity will vary with model. Parts: Quantity will vary with model.
PAGE 2
Legacy Modular Conference Table • INSTRUCTIONS (LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652, LCTRT24052, LCTRT26452, LCTRT28852) Organize your parts. You may need a rubber mallet. STEP 1: Attach Stringer(A) to one of the End Legs(A) by lining up the Eclip with its corresponding holes, and sliding down into place (see figure 1.) Please Note: End Legs (A) have EClip attachment holes on one side only.
PAGE 3
Legacy Modular Conference Table • INSTRUCTIONS (LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652, LCTRT24052, LCTRT26452, LCTRT28852) Organize your parts. You may need a rubber mallet. STEP 3: Attach next Stringer(D) to other side of Center Leg(B) by lining up Eclip with corresponding holes, and sliding down into place. STEP 4: Attach next End Leg(A) or Center Leg(B) (Will vary depending on model of table.) Attach by lining up holes with corresponding Eclip, and slilding down into place.
PAGE 4
Legacy Modular Conference Table • INSTRUCTIONS (LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652, LCTRT24052, LCTRT26452, LCTRT28852) Organize your parts. You may need a rubber mallet. STEP 5: Attach Center Piece(E) onto assembled base by lining up pre-drilled holes on the bottom with the EClips on each Eclip Bracket(G) and Center Leg(B) and sliding into place. Please Note: Repeat this step until you have used all included Center Pieces(E).
PAGE 5
Legacy Modular Conference Table • INSTRUCTIONS (LCTRT14452, LCTRT16852, LCTRT19252, LCTRT21652, LCTRT21652, LCTRT24052, LCTRT26452, LCTRT28852) Organize your parts. You may need a rubber mallet. STEP 7A: From underneath the table, lock all available Sash Locks on the Center Pieces(E) (see figure 1). STEP 7B: From underneath the table, attach all available Flat Brackets(E) by using Thumb Screws(E) (see figure 2). E I Figure 1. Figure 2. OPTIONAL STEP 8: Insert DPEL(J) using provided screws.