Instructions / Assembly

ManualsBrandsRegency ManualsAccent TablesKobe Grey 72 in. W x 30 in. D Flip Top Mobile Training Table

IMPORTANT NOTICE

Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the parts from being scratched.

Check to be sure that you have all parts and hardware.

Remove all wrapping materials, including staples & packing straps before you start to assemble.

Do not tighten all screws/bolts until completely assembled.

Keep all hardware parts, tools and packaging out of reach of children.

Any problems or questions please call Regency Oce Furniture at 1-866-816-9822

Kobe Flip Top Training Table

Organize your parts. You will need a drill, 16 mm and 5/16” socket wrenches, rubber mallet, pliers and measuring tape.

Two people are required for assembly.

(MKTBFT4824, MKTBFT6524, MKFT4824, MKFT6024, MKFT7224, MKFT8424)

Parts

A: Vertical Assembly • B: Table Top • C: Top Bracket • D: Feet (2)

Hardware:

E: Casters(4) • F: Small Screws (8) • G: Large Screws (8) (10 for MKTBFT6524) • H: Assembly Key • I: Foot Cap (2) • J: Small Bolt (2) •

K: Nut and Washer (2 Each)

Pre-Attached Hardware:

L: Long Bolt (2) • M: Small Nut (2)

E F G H I

J K

STEP 1: Attach 2 Casters (E) to each Foot (D) as shown in Figure 1.

Figure 1

Pre-Attached HardwareHardware Pack

Summary of content (4 pages)

PAGE 1
Kobe Flip Top Training Table (MKTBFT4824, MKTBFT6524, MKFT4824, MKFT6024, MKFT7224, MKFT8424) Organize your parts. You will need a drill, 16 mm and 5/16” socket wrenches, rubber mallet, pliers and measuring tape. Two people are required for assembly.
PAGE 2
Kobe Flip Top Training Table (MKTBFT4824, MKTBFT6524, MKFT4824, MKFT6024, MKFT7224, MKFT8424) STEP 2: Use Assembly Key (H) to remove Pre-Attached Long Bolts (L) from ends of Vertical Assembly (A). Attach Feet (D) to Vertical Assembly (A) with Long Bolts (L) as shown in Figure 2. Note: Holes in Feet (D) to attach Long Bolts (L) are drilled off-center. Make sure the shorter length of each Foot (D) coordinates with the same side as the levers of the Vertical Assembly (A).
PAGE 3
Kobe Flip Top Training Table (MKTBFT4824, MKTBFT6524, MKFT4824, MKFT6024, MKFT7224, MKFT8424) STEP 4: Attach Top Bracket (C) to both sides of Vertical Assembly (A) using Small Bolts (J) and Nuts and Washers (K) as shown in Figure 4. Note: To line up holes in Top Bracket (C) and Vertical Assembly (A) adjust tension by squeezing lever. J K C A Figure 4 STEP 5: Remove Pre-Attached Small Nuts (M) from springs on Top Bracket (C). Thread spring through holes on top rail of Vertical Assembly (A).
PAGE 4
Kobe Flip Top Training Table (MKTBFT4824, MKTBFT6524, MKFT4824, MKFT6024, MKFT7224, MKFT8424) STEP 6a: Ensure Assembly is correct and Feet (D) are facing the right direction. Tighten all Bolts, Nuts and Washers. STEP 6b: Conceal holes on bottom of Feet (D) with Foot Caps (I). I D STEP 7a: Place Table Top (B) on a clean flat surface with desired table finish face down. Using a measuring tape, center the base on Table Top (B).