• CEILING FAN OWNER’S MANUAL • •OASIS• 5/04 WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
GENERAL INSTALLATION & OPERATION INSTRUCTIONS IMPORTANT SAFEGUARDS: 1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. 2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
IMPORTANT SAFETY PRECAUTIONS Thank you for choosing a Regency Ceiling Fan. You have chosen the best! Your new ceiling fan has been designed to provide many years of service and enjoyment. WARNINGS: * Disconnect power by removing fuse or turning off circuit breaker before installing the fan. * To reduce the risk of fire, electrical shock, or personal injury, mount only to the building’s structure.
UNPACKING YOUR FAN Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, the decorative housing may shift, be bent or damaged. Examine all parts. You should have the following: 1 6 2 4 3A 7 3 5 5A 9 10 11 8 1 2, 3. 4. 5.
PREPARATION Parts identification on assembled fan Bracket Canopy Downrod Collar Blade Blade Arm Detachable Switch Housing Pull Chain Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box. Do not lay fan on its side as this could result in shifting of motor in decorative enclosure.
ASSEMBLY OF DOWNROD SYSTEM ATTACHING DOWNROD, CANOPY AND COLLAR COVER (FIG. 2): 1. Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out) facing upward. 2. Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove ball. 3.
INSTALLING THE FAN * 1. Be sure your hanger bracket is secure. The entire weight of the fan will now be hanging from it. 2. Lift fan body/downrod/ball assembly into hanger bracket opening. NOTE: The tab in hanger bracket opening should fit into slot on ball (Fig. 3). 3. Make wire connections, (refer to section titled “Electrical Connections”page 7) Hanger bracket tab 4. Slide canopy up and fasten to hanger bracket with screws provided AFTER all electrical connections are complete. Ball slot Ball Fig.
ELECTRICAL CONNECTIONS * ELECTRICAL CONNECTIONS: Be sure electricity is turned off at the main power box before wiring 1. Four wires are connected to the fan. Black - this is the “hot” power to run fan. White - this is the “common” power to run fan and light. Blue - this is the “hot” power for light kit. Green - Ground wire (on bracket or downrod) 2. If fan and light are to be connected to the same circuit, black and blue wires can both be connected to house circuit black wire.
BLADE ATTACHMENT BLADE ATTACHMENT: 1. Place washer on screw. Insert this assembly through the blade and start the screw into the blade arm. Repeat this procedure without tightening the screw until all screws have been started into the blade arm. (Fig. 4). 2. Tighten all screws. Repeat for remaining blade arms/blades. 3 Fasten blade assembly to motor with screws and washers provided. Repeat procedure for remaining blades (Fig. 5).
INSTALLATION OF REMOVABLE SWITCH HOUSING NOTE: Be sure to turn the power off before installing. 1. If installing light kit, attach to switch housing per instructions supplied with light kit. See “Electrical Connections” for hook up of light kit. Carefully remove light kit plug in bottom of switch housing. 2. Connect the plug and receptacle and make sure side buckle snaps in place. 3. Attach the switch housing to switch housing hub by aligning keyhole slots and tabs in both. 4.
GENERAL INSTALLATION & OPERATION INSTRUCTIONS Turn on the power and check operation of the fan. The fan is controlled by the use of the pull chain as follows: one pull = high speed two pulls = medium speed three pulls = low speed four pulls = off For proper functions, ensure that the chain is pulled down fully and released each time. * Leave fan in “high speed” position when using optional wall control. The slide switch on the side of the switch housing controls forward or reverse rotation.
THANK YOU FOR PURCHASING A REGENCY CEILING FAN. Write to us at: Regency Ceiling Fans P.O. Box 730 Fenton, MO 63026 Visit us on the Web at: www.regencyfan.