Users Manual
Table Of Contents
- Equipment Set Up and Initial Testing
- Turn BUS ignition switch to the ON position.
- Verify that the POWER indicator on the ECVR-6700T is Blue, and the radio loads with the REI logo screen.
- Vehicle Dimmer Check
- Camera Check
- Hand Microphone Check
- Wireless Microphone Check (if installed)
- Passenger Radio Check
- Press the PASSANGER RAD button on the ECVR-6700T control head to place the system in RADIO
- mode. Select the FM band if necessary. Passenger Radio should be displayed on the active section of the display.
- Tune the ECVR-6700T to a known good FM station using the SEEK/MANUAL tune buttons. Touch the tuner grid for quick frequency changes also.
- Audio should be present on both the left and right sides of the Passenger speakers on the Bus. The audio should be relatively clear without exceptional alternator or engine noise at normal volume levels. Adjust the level using the Passengers VOL/SEL k...
- Passenger Subwoofer Check (if installed)
- Passenger Tweeters Check (if installed)
- Passenger Video Check
- Insert a DVD disc into the disc slot. If disc doesn’t automatically begin playing, press VID button on the ECVR-6700T. Chapter and time information should be displayed on the ECVR-6700T. The video monitors shall ALL turn on, verify their operation. T...
- Press any of the playback options to control the DVD.
- Press EJECT button to eject DVD disc.
- Passenger Media Panel Check (if installed)
- Insert a USB THUMBDRIVE into the USB input on the media panel with .mp3 audio and verify audio playback. Radio should switch to USB after pressing the passengers SRC button, and begin playback.
- Recording levels will vary, adjust the PASSENGERS volume on the ECVR-6700T if necessary.
- Insert an audio source into the 3.5mm input. Switch the ECVR-6700T into EMS A/V 3 mode. Verify audio buy using the PASSANGERVOL/SEL knob to adjust the volume level. If necessary, adjust the level of the AUX audio source also.
- Remove the 3.5mm audio source and connect a valid HDMI audio/video source into the HDMI input. With the ECVR-6700T still in EMS mode select HDMI 2, verify the HD source is playing content. Check that all monitors are displaying HD video. Some delay...
- Media Player Verification Test (if installed)
- Passengers Bluetooth AUDIO Check
- Passengers AUX Check (if installed)
- External DVD2 Check (if installed)
- Driver Radio Check
- Press RAD button on the “DRIVER’s” section of the ECVR-6700T. Select the FM BAND, see below:
- Radio sound shall be heard in the DRIVERS speakers section. SEEK/MANUAL tune buttons. Touch the tuner grid for quick frequency changes also. The audio should be relatively clear without exceptional alternator or engine noise at normal volume levels.
- Adjust volume up and down using the DRIVER’s VOL/SEL knob. Display should read “Drivers” and the level adjusted will be indicated between 0-30.
- Drivers AUX Check (if installed)
- Drivers Bluetooth AUDIO Check
- Factory Setup
- Amplifier Adjustments (if necessary)
- Firmware Conformation
- It is recommended that the above steps be followed 2 times, once with and once without the coach running.
1.10.2. Insert an audio source into the 3.5mm input. Switch the ECVR-6700T into EMS A/V 3 mode. Verify audio
buy using the PASSANGERVOL/SEL knob to adjust the volume level. If necessary, adjust the level of
the AUX audio source also.
1.10.3. Remove the 3.5mm audio source and connect a valid HDMI audio/video source into the HDMI input. With
the ECVR-6700T still in EMS mode select HDMI 2, verify the HD source is playing content. Check that
all monitors are displaying HD video. Some delay is possible when waiting for HDMI connections to
properly sync. Verify audio buy using the PASSANGERVOL/SEL knob to adjust the volume level.