Rekon3 FPV Racing Drone Manual 1 rekonfpv.
Product Specifications.............................................................................................................................1 Interface Description...............................................................................................................................2 Check the flight control drive................................................................................................................3 Calibration accelerometer............................................
1.Product Specifications Product parameters Model Rekon3 VTX FPV Racing Drone Frame Kit Rekon3 Frame Kit Flight Controller Zeus5 AIO Flight Controller VTX Zeus nano 350mW 1202.5 Motor Motor 1S KV11600 Support Neceiver Input Voltage SBUS .DSMX.CRSF Weight 62.5g 1S Lipo 3 Rekonfpv.
2.Interface Description 4 Rekonfpv.
3.Check the flight control drive 1. Long Press BOOT buttons.connect USB.The system automatically install the driver 2.Driver cannot be installed, please download ImpulseRC_Driver_Fixer 3.Double-click on the run(Plug in the flight controller to automatically install the driver) 4.open betaflight configurator ，enter DFU mode 5 Rekonfpv.
5.Click 6.Click completion Select firmware version Load firmware. It will be prompted upon Waiting for completion. .Controller 7. open betaflight configurator plugged into the computer. Betaflight Automatically assigned port，click “Connect” Enter setup interface（Different computer COM） 6 Rekonfpv.
4. Calibration accelerometer 1. Put the aircraft horizontal and click“Reset Z axis” Click again 5.UART serial port use 1.UART1 uses WIFI Open WIFI CLI command: ‘’resource PINIO 1 B10 serial 0 1 115200 57600 0 115200 set pinio_config = 129,1,1,1 set pinio_box = 0,255,255,255 SAVE‘’ 7 Rekonfpv.
2. UART2 uses receiver S5 is a soft serial port, dedicated to video transmission (VTX) FM CLI command of soft serial port: ‘’resource MOTOR 5 none resource SERIAL_TX 11 B03 SAVE‘’ 6.WIFI function instruciton 1.Click Select Ports 2.Install Speedy Bee on your mobile phone. Connect to WIFI name Started with HermesXXXX. 3.Then click connect to adjust the parameters normally. 4.If the WIFI module light is solid, it means the WIFI is connected to the mobile phone.。 5.
7.Select aircraft model 1.Click 2.Click Select model Click “I understand the risks”Push Master to check motor steering“Master”Steering can be changed at BLHeliSuite 9 Rekonfpv.
8.Choose ESC protocol 9.Voltage and current parameters setting 1.Click Setting parameters 10 Rekonfpv.
10.Setting up the receiver 1.Receiver connection diagram 2.Click .have found“UART2”Open the receiver serial port 3.Set the SBUS receiver 4.Set the CRSF receiver 11 Rekonfpv.
11.VTX serial port use wiring 1. 5.8G VTX connection 2. 5.8G VTX serial port opens. The protocol is selected according to its own VTX protocol. 3.Use OSD to adjust VTX which displays information like battery voltage and mAh consumed while you fly. In addition, the Betaflight OSD can be used to configure the quadcopter, making in-field adjustments and tuning more convenient. MODE2 MODE1 12 Rekonfpv.
The graphics above show the stick command to bring up the OSD menu. The stick command is: throttle centered, yaw left, pitch forward. The exact stick command therefore depends on which mode your transmitter sticks are in. In the OSD menu, use pitch up/down to move the cursor between menu items. When a menu option has a > symbol to the right of it, this indicates that it contains a sub-menu. Roll-right will enter the sub-menu.
12.Check receiver signal 1.Click Check the remote control output signal 13.Select flight mode startup mode 1.Click set up the function of remote control switch across the channel (below are for reference only) 14 Rekonfpv.
14.OSD settings 1. Click the OSD Settings, according to the need to choose, drag the OSD schematic diagram of the parameters can be adjusted. 15.LED settings 1.Click 2.Click need Turn on LED support .Click set according to 15 Rekonfpv.
.Troubleshooting Warning: Please read the cautions as follows, otherwise stability of your flight controller cannot be ensured, your flight controller will even get damaged. ● Keep focus on the polarity. Check carefully before power supply. ● Cut off the power when you connect, plug and pull anything. ● The refresh rate of PID and Gyroscope is up to 8K/8K. after sales question: 1. After receiving the goods, it is found that the product can not be used normally.
Product daily problems 1.OSD garbled: If you find garbled characters, please open Betaflight, click “OSD” .and click “Font Manager” clicks on “Upload Font” to update 1. When plugged in the battery, the aircraft does not pass the self-test without "BBB" sound. There is only one sound. Please check if the ESC agreement is correct 3.The spin of the aircraft keeps spinning 1. Please check if the propeller is correct 2. Please check if the motor direction is correct 17 Rekonfpv.
