Use & care guide

ManualsBrandsReliance Water Heaters ManualsWater Heater606

Residential Electric

Heat Pump Water Heater

Installation

Instructions and

Use & Care Guide

To obtain technical, warranty or service assistance during or after

the installation of this water heater, call toll free

1-800-365-4054

When calling for assistance, please have the following

information ready:

1. Model number

2. 7 Digit product number

3. Serial number

4. Date of installation

5. Place of Purchase

Water Heater Safety ............................................................................... 2

Installing Your Water Heater .................................................................3-9

Consumer Information ................................................................ 3

Consumer Responsibilities ......................................................... 3

Unpacking Instructions ............................................................3-4

Location Requirements ............................................................... 4

Water System Piping ................................................................ 5-6

Temperature & Pressure Relief Valve .......................................7-8

Electrical Requirements ...........................................................8-9

Installation Checklist .............................................................................. 10

Operating Your Water Heater ........................................................... 11-13

Before Using ............................................................................. 11

Water Temperature Regulation ................................................. 11

Adjusting the User Interface Module/ Operational Mode .......... 12

Operational Conditions ............................................................. 13

Maintenance of Your Water Heater ..................................................14-15

Temperature and Pressure Relief Valve .................................... 14

Draining and Flushing ................................................................ 14

Heating Element Replacement ............................................. 14-15

Cleaning the Heat Pump ........................................................... 15

Diagnostic Codes .................................................................................. 16

Troubleshooting Chart ........................................................................... 17

Repair Parts Illustration ......................................................................... 18

Notes... ..............................................................................................19-20

Table of Contents Page

318259-001

August 2010

Summary of content (20 pages)

PAGE 1
Residential Electric Heat Pump Water Heater Installation Instructions and Use & Care Guide To obtain technical, warranty or service assistance during or after the installation of this water heater, call toll free 1-800-365-4054 When calling for assistance, please have the following information ready: 1. Model number 2. 7 Digit product number 3. Serial number 4. Date of installation 5. Place of Purchase Table of Contents Page Water Heater Safety .........................................................
PAGE 2
WATER HEATER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.
PAGE 3
INSTALLING YOUR WATER HEATER Consumer Information This water heater should be installed in accordance with the local code authority having jurisdiction, the power company or electric utility, and this installation manual. In the absence of local code requirements, follow the regulations set forth in the latest edition of The National Electric Code, NFPA 70.
PAGE 4
• The water heater must NOT be placed on its side. It should be transported and stored in an upright position. Remove exterior packaging and place installation components aside. Inspect all parts for damage prior to installation and start-up. Completely read all instructions before attempting to assemble and install this product. After installation, dispose of/recycle all packaging materials. • • • • Location Requirements Site location Select a location near the center of the water piping system.
PAGE 5
Water System Piping Piping, fittings, and valves should be installed according to the installation drawing (Figure 4). If the indoor installation area is subject to freezing temperatures, the water piping must be properly insulated. Water supply pressure should be 50-60 PSIG and not exceed the maximum 80 PSIG. If the supply line pressure exceeds 80 PSIG, a pressure reducing valve (PRV) with a bypass should be installed in the cold water supply line.
PAGE 6
Please note the following: • The system should be installed only with piping that is suitable for potable (drinkable) water such as copper, CPVC, or polybutylene. This water heater must not be installed using iron piping or PVC water piping. • Use only pumps, valves, or fittings that are compatible with potable water. • Use only full flow ball or gate valves. The use of valves that may cause excessive restriction to water flow is not recommended. • Use only 95/5 tin-antimony or other equivalent solder.
PAGE 7
Temperature and Pressure Relief Valve WARNING Explosion Hazard If the temperature and pressure relief valve is dripping or leaking, have a qualified person replace it. Examples of a qualified person include: licensed plumbers, authorized electric company personnel, and authorized service personnel. Do not plug valve. Do not remove valve. Failure to follow these instructions can result in death or explosion.
PAGE 8
Figure 6 T&P Relief Valve Insulation T&P Relief Valve Insulation Manual Relief Lever T&P Relief Valve T&P Relief Valve Drain Line 4. Locate the hot water (outlet) & cold water (inlet) pipes to the water heater. 5. Locate the slit running the length of a section of pipe insulation. 6. Spread the slit open and slip the insulation over the cold water (inlet) pipe. Apply gentle pressure along the length of the insulation to ensure that it is fully seated around the pipe.
PAGE 9
5. Connect these two wires to the two wires on the water heater using wire nuts or other connectors. Figure 8A Junction Box 6. Connect the free ends of the two wires to the shut off switch on the condensate pump in accordance with the manufacturers recommendations. Green Ground Wire 7. Turn on electrical power to the water heater. Ground Wire Black Wire Conduit (Field Connection) Red Wire 8. Press the power button to turn the water heater on and select the desired operational mode.
PAGE 10
INSTALLATION CHECKLIST Water Heater Location Condensate Drain Line Installation □ Centrally located with the water piping system. □ □ The flooring beneath the water heater must be able to support the weight of the water heater when filled with water (See Table 1). Must be located with access to an adequate drain or condensate pump. □ Condensate drain lines installed and piped to an adequate drain or condensate pump (See Figure 4).
PAGE 11
OPERATING YOUR WATER HEATER Before Using 1. Make sure the water heater has been properly installed. See “Installing Your Water Heater” section. 2. Make sure the air filter is correctly seated, as it may shift during shipping or installation. See “Repair Parts Illustration” section. 3. Completely fill the tank with water (See “Water Piping” section). 4. After the water heater tank is completely filled with water, connect electrical power to the water heater. 5.
PAGE 12
Adjusting the User Interface Module/Operational Modes Water Temperature Adjustment Other Controls The water temperature can be adjusted from 95°F to 150°F. on the front Use the Up and Down Buttons panel to set the desired temperature. IMPORTANT: Before attempting to adjust the thermostat, read the “Water Temperature Regulation” section. If the instructions are not clear, contact a qualified person. IMPORTANT: Filling a spa or hot tub from this water heater may result in extended recovery/re-heat time.
PAGE 13
Operational Conditions Water Heater Sounds Powered Anode Operation During the normal operation of the water heater, sounds or noises may be heard. These noises are common and may result from the following: To shelter the glass-lined water tank from corrosion through electrolysis, this water heater is equipped with a non-sacrificial powered anode which should not need to be replaced under normal operating conditions. NOTE: The powered anode operates only when electrical power is applied.
PAGE 14
MAINTENANCE OF YOUR WATER HEATER Temperature and Pressure Relief Valve WARNING Explosion Hazard If the temperature and pressure relief valve is dripping or leaking, have a qualified person replace it. Examples of a qualified person include: licensed plumbers, authorized electric company personnel, and authorized service personnel. Do not plug valve. Do not remove valve. Failure to follow these instructions can result in death or explosion.
PAGE 15
Routine Preventive Maintenance Figure 12: Wires Element Screws 4. Remove the access cover(s), then remove the foam insulation block. 5. Remove the protective plastic cover(s) over the elements from their attachment point. 6. Disconnect the electrical wires from the heating element(s) by loosening the screws (Figure 12). Remove the screw-in element(s) by turning the element(s) counterclockwise with a 1-1/2 inch socket wrench. Remove the existing gasket(s). 7.
PAGE 16
DIAGNOSTIC CODES DISPLAY SHOWS UPPER ELEMENT CONNECT FAULT INDICATES 1. Upper element is not functioning CORRECTIVE ACTION 1. 2. LOWER ELEMENT CONNECT FAULT 1. Lower element is not functioning 1. Turn off power at the circuit breaker/fuse box and check for a loose connection at the element. For access directions see “Heating Element Replacement” section. If error persists proceed to the next step. Replace non-functioning element. See “Heating Element Replacement” section. 2.
PAGE 17
DIAGNOSTIC CODES ELECTRONIC POWER ANODE ERROR #0-9 (# CAN BE 0-9) 1. Indicates the power anode is not operating properly 1. Contact a qualified person to service the unit. NOTE: The diagnostic codes listed above are the most common. If a diagnostic code not listed above is displayed, contact Residential Technical Assistance referencing the number on the front of this manual. TROUBLESHOOTING CHART PROBLEM NO HOT WATER POSSIBLE CAUSE(S) 1. No power to the water heater (power button not lit) 1.
PAGE 18
REPAIR PART ILLUSTRATION REPAIR PARTS LIST 11 PARTS DESCRIPTION ITEM 10 NO. 12 9 8 17 13 18 5 7 16 6 1 19 15 3 2 19 15 4 14 REPAIR PARTS Repair parts may be ordered through your plumber, local distributor, home improvement center, or by calling 1-800-365-4054. When ordering repair parts always give the following information: 1. Model, serial and product number 2. Item number 3.
PAGE 19
NOTES 19