Thank you for choosing the Reliance EC5805 Wi-Fi Router (EC5805). Note: Supported functions and actual appearance depend on the specific models you purchased. The following illustrations are provided for your reference only. For details about the model you selected, consult your service provider. This guide briefly describes the functions of the EC5805. For details about how to set management parameters, see Help on the web management page.
Getting to Know Your EC5805 Packing List The package should contain the following items. If any of the items are missing or damaged, contact your local dealer immediately. Main unit Battery Data cable Charger Quick Start Guide Safety Information Some accessories are optional and are not provided with the modem. To purchase any optional accessories, contact your local dealer.
Connection Scenarios A Wi-Fi device or computer can be connected to the Internet through the EC5805. The actual connection procedure depends on the operating system of the Wi-Fi device or computer. The connection scenarios illustrated here are for your reference.
Scenario 3: Multi-device access via Wi-Fi and USB at the same time Smart phone Game machine Digital camera Laptop
Appearance No.
Indicator Status Wi-Fi/WPS Power Signal Off: Wi-Fi and WPS are disabled. Continuously on green: Wi-Fi is enabled. Blinking green: The WPS is enabled. Blinking red: Battery power level is low and must be charged immediately. Otherwise the EC5805 will power off automatically. Continuously on red: Battery power is weak. Blinking green: Battery is being charged. Continuously on green: Battery power is good.
Installing the Battery Install the battery as shown. 1 2 3 Installing the microSD Card Install the microSD card as shown. Note: The microSD card is an optional accessory.
your Wi-Fi Router, you may purchase one yourself. To remove the microSD card, press in the card gently. The microSD card will pop out for removal. Do not remove the microSD card when it is in use. Doing so may damage the card and the EC5805, and data stored on the card may be lost. Charging the Battery Note: If the battery has not been used for a long time, it must be charged first.
Method 1: Using the charger Caution: Only use chargers compatible with the EC5805 and provided by a designated manufacturer. Use of an incompatible charger or one from an unknown manufacturer may cause the EC5805 to malfunction, fail, or could even cause a fire. Such use voids all warranties, whether expressed or implied, on the product. Method 2: Connecting to a PC for charging Connect the EC5805 to a PC using a compatible data cable.
Accessing the Internet via Wi-Fi Connection Note: By default, management parameters are preset on the EC5805 according to the requirements of the service provider. Follow the steps below to quickly access the Internet. For the details about how to set management parameters, see Help on the Web management page. Step1: Power on the EC5805. Step2: Establish a Wi-Fi Connection. Step3: Access the Internet. 1. Power on the EC5805 Press and hold power button until the indicators turn on.
on. Note: Press and hold power button until the indicators turn off. The EC5805 is powered off. 2. Establish a Wi-Fi Connection (Take a computer with Windows XP operating system as an example) . 1 Make sure that the Wi-Fi/WPS indicator is continuously on green. . 2 Select Start > Control Panel > Network Connections > Wireless Network Connection. Note: To set up a Wi-Fi connection, the PC must have a wireless network adapter installed.
you have a wireless network adapter installed. . 3 Click View available wireless networks to display a list of wireless networks available. . 4 Select a network that has the same SSID as that of the EC5805, and then click . Note: If the encryption parameter is already set for the EC5805, the Wireless Network Connection dialog box is displayed. Enter the network key in the dialog box as shown below. The SSID and key label are affixed to your EC5805, as illustrated below.
3. Access the Internet After successfully establishing a Wi-Fi connection, access the Internet in either the On Demand or Manual mode. The default mode is On Demand. Mode Operations On Demand Manual After the EC5805 is powered on, it can automatically connect to the network when data transmission is required. If no data transmission occurs over a certain period of time, the EC5805 automatically disconnects from the Internet.
network, you can only establish a network connection manually.
Accessing the Web Management Page . 1 Make sure that the connection between the EC5805 and the client is a proper one. . 2 Start the Internet browser and enter http://192.168.1.1 in the address bar.
. 3 Click the Login button on the upper-right corner of the page. . 4 To connect internet Click the ‘Connect’ button on index page. . 5 Enter the user name and password, and then click Login.
Note: The default user name is admin，The default password is admin.
Sharing Data Stored on the microSD card After the microSD card is inserted, you can store data on the card or use the web management page to share data stored on the card. . 6 Insert the microSD card. . 7 Access the web management page. . 8 Click SD Card to manage the data stored on the microSD card.
Please Note above details is for example purpose. Settings . 9 Setting > System > Device Information – All the information regarding the Device is provided . 10 Setting > System > network Settings – Preferred operating mode is shown, ideally the device should be kept in HYBRID (Broadband+ & High Speed 1x) . 11 Setting > System > Profile Settings – Please input the MDN which you can check from Setting > System > Device Information. Username: MDN Password: MDN Authentication: PAP+CHAP .
Daily Use Power Saving Mode If no operation is performed on the EC5805 for a while, the power indicator slowly blinks green, and all other indicators are off. The EC5805 is in standby state. If the EC5805 has not been accessed for 10 minutes (by default), it goes to deep sleep state and Wi-Fi is disabled. When the EC5805 is in deep sleep state, press and hold Wi-Fi/WPS button to enable Wi-Fi. Enabling/Disabling the Wi-Fi Function When the EC5805 is powered on, Wi-Fi is enabled by default.
Note: Press and hold the Wi-Fi/WPS button until the Wi-Fi/WPS indicator is off. WiFi is now disabled. Establishing a WPS Connection If a Wi-Fi client connected to the EC5805 supports the WPS function, the EC5805 can generate a network key without manual input. To establish a WPS connection, perform the following steps: . 1 Power on the EC5805. . 2 Start the client. . 3 Enable the WPS function of the EC5805. Note: After Wi-Fi is enabled, press and hold the Wi-Fi/WPS button.
Restoring Factory Defaults If you forget the changes you have made to some parameters, you may restore factory defaults and reconfigure the EC5805. To restore the factory defaults, press and hold the RESET button until all the indicators are off. All factory default settings are successfully restored. Note: Restoring factory defaults deletes all personal configuration settings and restores all web-based management settings and parameters to their default values.
Example 1: Wi-Fi Connection to Game Machine (Sony PSP) . 1 Make sure that the Wi-Fi of the EC5805 is enabled. . 2 Turn on the PSP WLAN switch. . 3 Select Settings > Network Settings. . 4 Select Infrastructure Mode to connect to your local Wi-Fi access point. . 5 Select New Connection to specify an easy to remember connection name (such as MyEC5805). . 6 Select Scan to detect all networks within range. The access point list is displayed.
. 7 Select the SSID the same way as you did for the EC5805. First press the ► button of your game machine to confirm the SSID and then press it again to input the Wi-Fi key. SSID: The Wi-Fi name of the EC5805. WEP: The Wi-Fi key of the EC5805. The default SSID and key label are affixed to the EC5805. . 8 Press the ► button of your game machine to continue, and then press the X button to save the settings. . 9 Select Test Connection to check the connection. If the test succeeds, you are online. .
Example 2: Wi-Fi Connection to a Smart Phone (iPhone) . 1 Make sure that the Wi-Fi of the EC5805 is enabled. . 2 Select Settings > Wi-Fi, and then turn on Wi-Fi. . 3 Automatically detect the networks in range and display the access point list. . 4 Select a network that the EC5805 is using. . 5 If necessary, enter a password and tap Join. (Networks requiring a password appear with a lock icon.) Note: Some Wi-Fi clients such as iTouch, PS3 and NDS can also access the Internet via the EC5805.
Frequently Asked Questions (FAQ) What can I do if a client cannot access the Internet? .1 .2 .3 .4 Check that the client is properly connected to the EC5805. Check power status to ensure that the EC5805 is powered on. Check signal strength to ensure that the area is covered by the network. Check that the User Name, Password and Authentication are correct. For details, See Profile Settings on the web management page. .
What can I do if a client cannot access the WLAN? . 1 If interference seems to be the problem, adjust the position of the EC5805 or move it to a more favorable location. . 2 Check and record the following settings for your client and your EC5805: SSID, WEP type, and key. The SSID of the client must be set to ANY or to the same value as that of the EC5805. The WEP type and key of the client must be the same as that of the EC5805. Change the settings as needed. .
Version: V100R001_01 Part Number: 31010XXX 29
