Relion Lithium Charging Instructions

ManualsBrandsRelion ManualsWind and Solar EnergyRelion RB20 Lithium Ion LiFePO4 Battery 12V 20Ah

relionbattery.com

1.803.547.7288

844.385.9840

9868 Harrisburg Road

Fort Mill, SC 29707, US

© 2018 Relion Battery, LLC. All rights reserved. Relion Battery is not liable for damages that may result from any information provided in or omitted from this publication, under any circumstances. Relion Battery reserves the right to make adjustments to this publication at any time, without notice or obligation.

Charging Instructions 06.13.18

CHARGING INSTRUCTIONS

RELiON LITHIUM IRON PHOSPHATE (LiFePO4) BATTERIES

To ensure your Lithium Iron Phosphate (LiFePO) battery provide its maximum life, follow these Charging Instructions. When

charging LiFePO make sure that you are not using a charger meant for other lithium ion chemistries, which are typically set to a

higher voltage than required by LiFePO batteries. A lead-acid battery charger can be used if the voltage settings are within the

parameters of LiFePO batteries.

Charger Inspection

Check that your charger cables are insulated and free of breakage. Charger terminal connectors should be clean and properly

mate with the battery terminals to ensure a good connection and optimum conductivity.

Charging Guidelines

When to Charge your LiFePO4 Battery

If LiFePO batteries are not fully discharged, they do not need to be charged after each use. LiFePO batteries do not get damaged

when left in a partial state of charge (PSOC). You can charge your LiFePO batteries after each use or when they have been

discharged up to 80% (20% SOC). If the Battery Management System (BMS) disconnects the battery due to low voltage, at 100%

depth of discharge, remove the load to reconnect the battery circuit and charge immediately. Please note that we recommend

storing batteries at 50% state of charge (SOC) to minimize irreversible capacity loss.

Charging Temperature

LiFePO batteries can safely charge between -20°C to 55°C (-4°F to 131°F). However, at temperatures below 0°C (32°F) the charge

current must be reduced, until the temperature is >0ºC (32ºF), as follows:

1. 0°C to -10°C (32°F to 14°F) charge at 0.1C (10% of the battery capacity)

2. -10°C to -20°C (14°F to -4°F) charge at 0.05C (5% of the battery capacity)

LiFePO batteries do not require temperature compensation for voltage when charging at hot or cold temperatures.

All Relion LiFePO come with a BMS that protects the battery from over-temperature. If the BMS disconnects due to high

temperature, wait until the temperature reduces and the BMS reconnects the battery circuit before using or charging the battery.

Please refer to your battery data sheet for the BMS high temperature cut-o value.

Charging with Lead-Acid Battery Chargers

Most lead-acid battery chargers can be used with LiFePO batteries as long as they are within the appropriate voltage guidelines.

AGM and Gel algorithms typically fall within the LiFePO voltage requirements. The voltage for flooded battery charging algorithms

are often higher than LiFePO requirements, which will result in the BMS disconnecting the battery at the end of the charge cycle

and possibly result in the charger displaying an error code. If this happens, it is generally a good practice to replace your charger

for one with a LiFePO charge profile. Since the BMS protects the battery, using lead-acid chargers will typically not damage the

battery.

Summary of content (4 pages)

PAGE 1
CHARGING INSTRUCTIONS RELiON LITHIUM IRON PHOSPHATE (LiFePO4) BATTERIES To ensure your Lithium Iron Phosphate (LiFePO4) battery provide its maximum life, follow these Charging Instructions. When charging LiFePO4 make sure that you are not using a charger meant for other lithium ion chemistries, which are typically set to a higher voltage than required by LiFePO4 batteries. A lead-acid battery charger can be used if the voltage settings are within the parameters of LiFePO4 batteries.
PAGE 2
CHARGING INSTRUCTIONS Charging Parameters LiFePO4 can be charged with either a 1-stage profile (constant current (CC) aka Bulk Stage) or a 2-stage profile (constant current, constant voltage (CC-CV) profile aka Bulk and Absorption Stages). The 1-stage profile will charge the battery ~95% and the 2-stage profile will charge the battery 100%. The 1-stage profile is sufficient, since LiFePO4 batteries do not need to be fully charged; this will not reduce life as it does with lead-acid.
PAGE 3
CHARGING INSTRUCTIONS Charging Series or Parallel Systems When connecting batteries in series or parallel, please make sure each battery is within 50mV (0.05V) of each other before putting them in service. This will minimize the chance of imbalance between batteries. If your batteries get out of balance, the voltage of any battery is >50mV (0.05V) from another battery in the set, you should charge each battery individually to rebalance.
PAGE 4
CHARGING INSTRUCTIONS Charging with an Inverter or Charge Controller Charger Inverter and Charge Controller Charge Parameters Below are the typical charger inputs when using an inverter or charge controller with LiFePO4 batteries. LiFePO4 batteries do not require equalizing. LiFePO4 batteries do not require temperature compensation for voltage when charging at hot or cold temperatures. CHARGE PARAMETER 12V SYSTEM 24V SYSTEM 48V SYSTEM Bulk Voltage 14V – 14.6V 28V - 29.2V 56V - 58.