User Manual

18 BK Radio
TALKBACK SCAN
If your radio is programmed for Talkback
Scan, press PTT while a channel is active or
while scan delay time remains. You will be
responding on the transmit frequency of the
received channel.
Talkback Scan will not work if Priority Scan is
also on and your radio is programmed to
always transmit on the Priority 1 channel.
CHANGE THE SCAN LIST
If the radio has not been programmed for
Scan List Lock, the user may add or remove
channels from the Scan List. If user changes
are enabled, follow these steps to change the
Scan List:
1. Slide Switches B (scan) and C (priority)
down.
2. Select a channel
to be added or removed
from the Scan List by turning the Channel
Selector knob. If the channel is already on
the Scan List, SCN appears in the display.
3. Press the [ENT] key
to add a channel to
the Scan List. A short beep sounds and
SCN appears in the display.
4. Press the [CLR] key
to remove a channel
from the Scan List. A short beep sounds
and SCN disappears from the display.
GROUP SCAN
Channels on each “Channel Scan List” in
groups on the “Group Scan List” are scanned
sequentially. The selected group is always
scanned when Group Scan is enabled, even if
that group is not on the Group Scan List.
When Group Scan is enabled, the following
features are disabled:
• Priority Scan
• Dual Priority Scan
• User-Selected Channel Guard
• Nuisance Channel Delete
SCN
LABEL 1
2
1 2
3
4
5
6
7
8
9
0
*
#
CLR
FCN
PRI
ENT
DPH Owner’s Manual 27
INITIATING A UNIT-TO-UNIT CALL
To initiate a Unit-To-Unit call, press the [*] key
to enter Unit-To-Unit Mode. The label of the
last active (called or received) ID will appear
on the display.
If the last active ID was a Call List ID, its label
will be displayed along with the phone icon,
otherwise the numeric ID will be displayed
along with the phone and ID icon. If a label is
displayed, press and hold [#] to view the
corresponding numeric ID.
To place a call to the displayed unit, press
PTT. To choose another unit, use the keypad
to enter the desired call list entry (0 - 9), or
press [PRI] repeatedly to cycle through all call
list entries, or press [#] to manually key in a
new ID (up to 7 digits). To re-select the ‘last
active’ ID, press the [*] key. Once the new
unit ID is selected or entered, press PTT to
place the call.
To exit Unit-To-Unit Mode, press and hold
the [*] key.
RECEIVING A UNIT-TO-UNIT CALL
When a Unit-To-Unit call is received while the
radio is in normal Operating Mode, the radio
will beep twice. The display will show the ID
of the calling unit. If the ID matches one of the
Call List IDs, the associated label will be
displayed along with the RX and phone icons.
Otherwise the numeric ID will be displayed
along with the RX, phone, and ID icons. The
calling unit’s ID will be displayed for the
duration of the reception, and once the signal
goes away, for a programmed hold time.
When the hold time expires, the display will
return to the normal Operating Mode display,
but the phone icon will flash until the [*] key is
pressed, putting the radio in Unit-To-Unit
Mode, displaying the last active ID.
1 2 3
4 5 6
7 8 9
0
*
#
CLR
FCN
PRI
ENT
LABE
L
Last Active Was Unit
On Call List
ID
<
Prompt For
Manual ID Entr
y
RX
LABE
L
Incoming Call From
Unit
O
n
Call List
ID
14
5
Last Active Was Unit
Not On Call List
C
H
5
Missed Call
Incoming Call From
Unit Not On Call List
RX ID
14
5