User Manual

6 BK Radio
FEDERAL COMMUNICATIONS COMMISSION
REGULATIONS
The FCC rules require manufacturers to comply with the FCC RF
energy exposure limits for portable 2-way radios before they can be
marketed in the U.S. When 2-way radios are used as a consequence
of employment, the FCC requires users to be fully aware of and able to
control their exposure to meet occupational requirements. Exposure
awareness can be facilitated by the use of a product label directing
users to specific user awareness information. Your BK Radio 2-way
radio has a RF exposure product label. Also, your BK Radio owner’s
and service manuals include information and operating instructions
required to control your RF exposure and to satisfy compliance
requirements.
COMPLIANCE WITH RF EXPOSURE STANDARDS
Your BK Radio 2-way radio is designed and tested to comply with a
number of national and international standards and guidelines (listed
below) for human exposure to radio frequency electromagnetic energy.
This radio complies with the IEEE and ICNIRP exposure limits for
occupational/controlled RF exposure environment at operating duty
factors of up to 50% transmitting and is authorized by the FCC for
occupational use only. In terms of measuring RF energy for
compliance with the FCC exposure guidelines, your radio radiates
measurable RF energy only while it is transmitting (during talking), not
when it is receiving (listening) or in Standby Mode. Note: The approved
batteries supplied with this radio are rated for a 5-5-90 duty factor (5%
talk-5% listen - 90% standby), even though this radio complies with the
FCC occupational RF exposure limits and may operate at duty factors
of up to 50% talk.
Your BK Radio 2-way radio complies with the following RF energy
exposure standards and guidelines:
• United States Federal Communications Commission, Code of
Federal Regulations; 47 CFR §§ 1.1307, 1.1310, 2.1091 and
2.1093
• American National Standards Institute (ANSI) / Institute of
Electrical and Electronic Engineers (IEEE) C95. 1-1992
• Institute of Electrical and Electronic Engineers (IEEE) C95.1-
1999 Edition
INDUSTRY CANADA COMPLIANCE
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numerique de la classe B est conforme à la norme NMB-
003 Canada.
DPH Owner’s Manual 39
SPECIAL CLONING INSTRUCTIONS
You can change Channel 0 values on the master radio, hold them in a
temporary memory, and download them to the clone without actually
entering them into the permanent memory of the master. This is
convenient if sequential identification numbers are used to identify a
series of portables in a radio system. Assuming that the frequencies,
Channel Guard values, and other CH 0 values are common for all
radios in the system, but that the radio identification number should be
unique to each radio, the following method can be used to clone
additional radios for the system:
1. Program the master with all frequencies,
Channel Guard values, and Channel 0
values that will be common to all radios.
2. Advance the display to show the ID
number of the master (for example 100).
3. Press [CLR]; press 1, 2, and 5. The ID
number 125 is now only in temporary
memory.
4. Press
[*], connect the cloning cable to the
clone radio, and download by pressing
[FCN]. ID number 125 is now stored in the
permanent memory of the clone.
5. After downloading, press
[CLR] on the
Master radio. Disconnect the clone. The
master radio display will show that 125 is
still being held in the temporary memory of
the master.
6. Press [PRI]. This will increment the ID
number one digit to 126.
NOTE: Any new number can be entered
at this point by pressing [CLR]
and using the keypad to enter the
new number.
7. Press
[*]. Connect the cloning cable to
the next clone and download by pressing
[FCN].
Any number of radios can be coded with
different or sequential ID numbers using
this technique. The ID number in the
permanent memory of the master will
remain unchanged at 100.
PRG ID
1
2
5
PRG ID
12
5
PRG ID
126
1 2 3
4 5
6
7 8
9
0
*
#
CLR
FCN
PRI
ENT