User's Manual
Table Of Contents
- Introduction
- FCC Requirements
- Industry Canada Compliance
- Safety Precautions
- Information and Options
- Battery Installation and Removal
- Battery Care and Maintenance
- Antenna Installation and Removal
- Radio Controls
- LCD Display
- Programmable Switch and Button Functions
- Channel/Zone Selection Options
- Basic Radio Operation
- Command Zone Operation
- Code Guard/NAC Operation
- Mixed Mode Operation
- Trunking Channel Basic Operation
- Scan Options
- Pick List Options
- Unit-to-Unit Call Options
- Emergency Signaling Options
- Encryption Operation
- Messaging
- Paging and Call Alert
- Radio Inhibit/Enable [INH]/[UNINH]
- Other Options and Functions
- Backlight [LITE]
- Battery Life [LIFE]
- Bluetooth [BT]
- Busy Channel Operation
- Channel Select [CHAN]
- Cloning [CLON]
- Contrast
- Control Lockout [LCK]
- Date and Time [DATE]
- Global Positioning [GPS]
- Hard Power Down [PWRD]
- Keypad Programming
- Minimum Volume [VOL]
- Monitor [MON]
- Nuisance Channel Delete [DEL]
- Phone [PHN] and Hang Up [HANG]
- Radio Accountability Tone [RAT]
- Radio info
- Repeater Talkaround [T/A]
- Send Alert Tone [SNDT]
- Send Signal [SEND]
- Squelch Adjust [SQL]
- Site Display [STDS]
- Site Lock [STLK]
- Site Search [STSR]
- Surveillance Mode [SURV]
- System Test
- Transmit Digital [TXAD]
- Transmit Power [PWR]
- Two-Tone Select [TONE]
- Versions
- Zone Select [ZONE] (Conventional and Trunked Channels)
- Keypad Programming
- Warranty
- My Radio Settings
RELM Wireless Corporation
- 22 -
Mixed Mode Operation
The receiver and transmitter are capable of operating in analog wide-
band (25 kHz channel spacing), analog narrow-band (12.5 kHz channel
spacing) and APCO Project 25 Digital Mode.
Each channel’s Receive and Transmit Mode can be set independently
as follows:
Mode RX TX
Analog Receive qualied analog
signals only
Transmit analog signals only
Digital Receive qualied digital
signals only
Transmit digital signals only
Mixed Automatically receive qualied
analog or digital signals
Transmit analog or digital signal,
depending on the status of “TX
Digital” switch
Digital receptions and transmissions will be
indicated by illuminating the D annunciator in
addition to the RX or TX annunciator.
Analog receptions and transmissions will be
indicated by illuminating the A annunciator in
addition to the RX or TX annunciator.
Mixed Mode Talkback
If Mixed Mode Talkback is enabled, transmissions initiated while
hold time remains will be in the same mode as the received signal,
if the signal was received on the Ready to Transmit (RTX) channel.
Depending on programming, the RTX channel can be the main
channel, a held scan or priority channel if Talkback Scan is enabled, or
the Priority 1 channel if “TX on PR1” is enabled. TX Mode on the RTX
channel must be set to MIXED.
While hold time after a reception remains,
transmissions will be in the same mode as the
received signal, regardless of the status of the
TX Digital switch. As in Talkback Scan, the
RTX channel and receive annunciators will be
displayed for the duration of the timer.
Ch 1
171.58500 MHz
TXD
KNG2-P150
CHAN+ TXCG ZONE MENU
Ch 1
171.58500 MHz
TXA
KNG2-P150
CHAN+ TXCG ZONE MENU
Ch 1
171.58500 MHz
RXD
KNG2-P150
CHAN+ TXCG ZONE MENU
Press the PTT while the RX
indicator is shown