, OWNER S MANUAL RPU4200A FM HANDHELD TRANSCEIVER
NOTE , OWNER S MANUAL RPU4200A FM HANDHELD TRANSCEIVER We are very grateful for your purchasing brand twoway radios produced by Relm Wireless Corporation. We believe two-way radio, which always incorporates the latest technology, can bring great convenience to your life and work; we also believe that the quality and function of twoway radio can meet your demands for reliable communication. PRECAUTIONS Please observe the following precautions to prevent fire, personal injury, and radio damage.
Do not place the radio in excessively humid areas or on unstable surfaces. Do not modify this radio for any reason. Refer service to qualified licensed or certificated technicians only. Notice to the User: Government laws prohibit radio communication without permission in government districts. Illegal operation is subject to punishment by fine and/or imprisonment. Refer service to the well-trained professional technicians only.
receive for 4 minutes. Long time transmitting or continuous working in high power mode will make the rear side of the radio generate heat. Please don't disassemble or assemble the radio under any circumstances. Please don't expose the radio to direct sunlight for a long time; don't place the radio near any heating devices, either. Please don't put the radio in extremely dusty, moist or dabbling places; don't place it on any unstable surfaces, either.
UNPACKING AND CHECKING EQUIPMENT Carefully unpack the radio. We recommend that you identify the items listed in the following table before discarding the packing material. If any damage has occurred during shipment, please contact the dealer immediately . PREPARATION CHARGING THE BATTERY PACK A new battery or a battery whose power appears low (power indicator displays one bar or no bar) needs charging before using.
* Do not charge the battery again if it has been fully charged or it is not in the low battery warning state, otherwise, its life will be shortened or it will be damaged. * Remove the battery from the charger after charging. * If the battery has been depleted, the red indicator will light approximately 1 minute after the battery is placed in the charger.
RADIO OVERVIEW 2 7 1 6 4 5 3 8 channel number will be changed. Emergency Button Press and hold this button for over 2 seconds to activate warning tone. Press it again to exit the emergency alert state. Note: When warning tone sounds, all of the buttons are disabled. Microphone/Speaker Jacks For connecting external Microphone/Speaker. BASIC OPERATION LED Indicator Lights red while transmitting; lights green while receiving a signal. Flashes red while in low battery power.
Make a Call To make a call, select the desired channel, press and hold the PTT button, and speak in normal voice. Please keep your mouth 1-2 in. away from the microphone. Receive a Call Release the PTT button to receive a call. Select the desired channel and adjust the volume to a proper level. SCAN FUNCTION (See your dealer for setting-up the Scan List and Scan Functions.
the scanning pause, the radio will transmit from the currently working channel. Note: Currently working channel means the channel in which the radio holds on under the following four conditions. 1) After receiving the signals, the radio will still stay in the current channel before restarting the scan. 2) When receiving signals during scanning, the radio will pause on the current channel and will keep staying on it for 3 seconds after the signals disappears.
Monitor Lock: Press the monitor button once to mute the audio. Press it again to mute the audio and return to normal operation. SQ Off: When there is no signal received, the squelch circuit of the radio will automatically mute the speaker, so you will not hear the background noise. Press the MONI key to un-mute the audio. CTCSS/DCS CTCSS/DCS tones may have been pre-programmed on some channels.
TROUBLE SHOOTING GUIDE NO. PROBLEM The radio cannot be switched on 1 or no display after being switched on. SOLUTION Battery power may be insufficient. Recharge or replace the battery pack. Battery pack may not be installed properly. Remove the battery pack and install it again. SETTINGS (set by the dealer) Model: ____________ 1) Serial No.: ___________ Channels List CHANNEL TRANSMITTING FREQUENCY RECEIVING FREQUENCY CTCSS/DCS 1 2 3 2 The battery power consumes quickly after charging.
Selected channel Selected channel or currently working channel Priority channel Priority channel or currently working channel 4) Squelch monitor: Open Close 5) Time-out timer: Open Close 6) Automatic scan: Open Close 15 CE Versions of the RPU4200A which display the "CE" symbol on the serial number seal, comply with the essential requirements of the European Radio and Telecommunication Terminal Directive 1999/5/EC.
