IM_IQ2.qxp 10.07.2008 14:27 Uhr Seite 1 Bedienungsanleitung m ACHTUNG! Lesen Sie sich vor der ersten Inbetriebnahme zur eigenen Sicherheit diese Bedienungsanleitung sorgfältig durch! Alle Personen, die mit der Aufstellung, Inbetriebnahme, Bedienung, Wartung und Instandhaltung dieses Gerätes zu tun haben, müssen entsprechend qualifiziert sein und diese Betriebsanleitung genau beachten.
IM_IQ2.qxp 10.07.2008 14:27 Uhr Seite 2 BEDIENUNGSANLEITUNG DEUTSCH Wir gratulieren Ihnen zum Kauf des Reloop IQ2+ / Reloop IQ2+ USB Mischpultes. Vielen Dank, dass Sie unserer Diskjockey-Technologie Ihr Vertrauen schenken. Vor Inbetriebnahme bitten wir Sie, alle Anweisungen sorgfältig zu studieren und zu befolgen. Nehmen Sie den Reloop IQ2+ / Reloop IQ2+ USB aus der Verpackung. Bitte überprüfen Sie vor der ersten Inbetriebnahme, ob kein offensichtlicher Transportschaden vorliegt.
IM_IQ2.qxp 10.07.2008 14:27 Uhr - - - - - - - - Stellen Sie keine Flüssigkeitsbehälter, die leicht umfallen können, auf dem Gerät oder in dessen Nähe ab. Falls doch einmal Flüssigkeit in das Geräteinnere gelangen sollte, sofort den Netzstecker ziehen. Lassen Sie das Gerät von einem qualifizierten Servicetechniker prüfen, bevor es erneut genutzt wird. Beschädigungen, die durch Flüssigkeiten im Gerät hervorgerufen wurden, sind von der Gewährleistung ausgeschlossen.
IM_IQ2.qxp 10.07.2008 14:27 Uhr Seite 4 BESTIMMUNGSGEMÄßE VERWENDUNG - - - - Bei diesem Gerät handelt es sich um ein professionelles Mischpult, mit dem sich niederpegelige Audiosignale regeln und mischen lassen. Das Gerät wird dabei zwischen einer Signalquelle und eine Audioendstufe geschlossen. Dieses Produkt ist für den Anschluss an 240 V, 50 Hz Wechselspannung zugelassen und wurde ausschließlich zur Verwendung in Innenräumen konzipiert.
IM_IQ2.qxp 10.07.
IM_IQ2.qxp 10.07.
IM_IQ2.qxp 10.07.2008 14:27 Uhr Seite 7 BEZEICHNUNGEN DEUTSCH 1. . . . . . . Mikrofon-Lautstärkedrehregler 2. . . . . . . 2-Band Equalizer für Mikrofon 3. . . . . . . Mikrofon-, Talkover-, Aktivierungsschalter 4. . . . . . . Gain-Drehregler Kanäle A + B 5. . . . . . . 3-Band Equalizer für Kanäle A + B 6. . . . . . . Signal-Eingangswahlschalter für Kanäle A + B (USB-Position nur für Reloop IQ2+ USB) 7. . . . . . . Master Volume-Drehregler 8. . . . . . Cue Volume-Drehregler 9. . . . . .
IM_IQ2.qxp 10.07.2008 14:27 Uhr Seite 8 BEZEICHNUNGEN LCD INFORMATIONS-DISPLAY -13- I V II IV III I...............Kanalzuweisungs-Anzeige II..............BPM-Anzeige III.............X-Parameter-Anzeige IV.............Y-Parameter-Anzeige V..............Effektauswahl-Anzeige DEUTSCH ANSCHLÜSSE 1. Verbinden Sie Ihre Line-Quellen (CD-Player, MD-Player, etc.) und Ihre Plattenspieler mit den Eingangsbuchsen für Kanal A und B -31-.
IM_IQ2.qxp 10.07.2008 14:27 Uhr Seite 9 5. Verbinden Sie beispielsweise einen MP3-Player mit der AUX-Eingangsbuchse (3,5 mm Klinke) -38-. Wenn Sie Tracks Ihres MP3-Players über den Mixer abspielen wollen, so muss der CD1/AUX-Eingangsschalter -37- auf die Position „AUX“ gestellt werden. Wenn Sie Tracks Ihres an Kanal A angeschlossenen CD-Players über den Mixer abspielen wollen, so muss der CD1/AUXEingangsschalter -37- auf die Position „CD1“ gestellt werden.
IM_IQ2.qxp 10.07.2008 14:27 Uhr Seite 10 BEDIENUNG 1. Strom einschalten [siehe Bezeichnungen, Nummer 27] Nachdem alle Anschlüssse vorgenommen wurden, schalten Sie das Gerät bitte mit dem EIN/AUS-Schalter -27- ein. 2.
IM_IQ2.qxp 10.07.2008 14:27 Uhr 7. Seite 11 Faderstart [siehe Bezeichnungen, Nummern 17, 21, 28 & 40] Falls Sie zwei geeignete CD-Player mit dem Reloop IQ2+ (wie unter dem Kapitel „Anschlüsse“, Punkt 7 beschrieben) verbunden haben, so können Sie diese mit dem Crossfader -21- oder mit den Linefadern -17- fernsteuern.
IM_IQ2.qxp 10.07.2008 14:27 Uhr Seite 12 DEUTSCH 9. Aussteuerung [siehe Bezeichnungen, Nummern 4, 5, 7, 10, 17 & 42] Die Aussteuerungs-LEDs für Cue/Master -12- zeigen die Ausgangspegel für die Kanäle A und B an. Zwischen den beiden LEDs befindet sich eine Leiste die mit Zahlen von -24 bis +14 beschriftet ist.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 13 13. Beatcounter [siehe Bezeichnungen, Nummern 13, 16 & 23] Das Reloop IQ2+ Mischpult ist mit einem automatischen und einem manuellen Beatcounter ausgestattet. Wenn Sie das Mischpult einschalten, ist der automatische Beatcounter eingestellt. Wählen Sie mittels des EffektZuweisungsreglers -16- den Kanal dessen BPM-Wert ermittelt werden soll (Position A entspricht Kanal A; Position B entspricht Kanal B).
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 14 Je nach Effekt sind Art und Bereich des Zeitparameters und die durch den Taktzuweisungsschalter -24- vorgenommenen Veränderungen verschieden: • ECHO = Echo-Effekt Wiederholt einen bestimmten Intervall des Signals dauerhaft. Zeitparameter-Wert: 2 – 2000 mSec Direkt-Taktzuweisung: Intervalle von 125 – 2000 einstellbar Drehen des X Parameter-Drehregler -25- verändert den Wert in 1er Schritten.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 15 • REVERB = Reverb-Effekt Simuliert Reflexionen von Schallwellen in einem natürlich begrenzten Bereich. Zeitparameter-Wert: 0 – 100% Direkt-Taktzuweisung: 0/20/40/60/80/100% Drehen des X-Parameter-Drehreglers -25- verändert den Wert in 1er Schritten. XParameter-Drehregler -25- gedrückt halten und drehen verändert den Wert in 10er Schritten.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 16 Es stehen Ihnen die folgenden drei Crossfader-Effekte zur Verfügung: a.) LoopX: Je nach ausgewähltem Takt, den Sie zuvor mittels des X-Parameter-Drehreglers -25- oder der Taktzuweisungstasten für die DSP Effekteinheit -24- (wie im Kapitel Bedienung, Punkt 14 beschrieben) eingestellt haben, wird mit diesem Effekt ein Loop erzeugt. Je weiter der Crossfader zur gegenüberliegenden Seite bewegt wird, desto leiser wird die Loop-Frequenz.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 17 TECHNISCHE DATEN Folgende Daten des Herstellers werden von der Global Distribution GmbH nicht auf Plausibilität und Richtigkeit geprüft: Eingänge: . . . . . . . . . . . . . . . . . . . . . .2 x Phono, 2mV/47 kOhm; . . . . . . . . . . . . . . . . . . . . . . . . . . . .2(+2) x Line, 200mV/47 kOhm; . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 x Mic, 2mV/10 kOhm; . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 x AUX 200mV/10 kOhm Ausgänge: . . .
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 18 OPERATION MANUAL ENGLISH Congratulations on purchasing your Reloop IQ2+ / Reloop IQ2+ USB. Thank you for placing your trust in our disc jockey technology. Before operating this equipment we ask you to carefully study and observe all instructions. Please remove the Reloop IQ2+ / Reloop IQ2+ USB from its packaging. Check before initial operation to make sure that the device has not been visibly damaged during transport.
IM_IQ2.qxp 10.07.2008 14:28 Uhr - - - - - - - Do not rest any containers filled with liquid that could easily spill onto the device or in its immediate vicinity. If, however, fluids should access the inside of the device, immediately disconnect the mains plug. Have the device checked by a qualified service technician before re-use. Damage caused by fluids inside the device is excluded from the warranty.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 20 APPLICATION IN ACCORDANCE WITH REGULATIONS - - - This device is a professional mixing console which can regulate and mix low level audio signals. The device is thereby connected between a signal source and an audio amplifier. This product is authorised for connection to 240 V, 50 Hz AC and is designed exclusively for indoor application.
IM_IQ2.qxp 10.07.
IM_IQ2.qxp 10.07.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 23 DESIGNATIONS ENGLISH 1. .............Microphone volume knob 2. ...........2-band equalizer for microphone 3. ............Microphone, talkover, activation switch 4. ...........Gain knob for channels A + B 5. ...........3-band equalizer for channels A + B 6. ...........Signal input selector for channels A + B (USB position only available for Reloop IQ2+ USB) 7. ............Master volume knob 8. ...........Cue volume knob 9. ...........CueFX LED button 10. .......
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 24 DESIGNATIONS LCD INFO DISPLAY -13- I V II IV III I...............Channel assignment indicator II..............BPM indicator III.............X parameter indicator IV.............Y parameter indicator V..............Effect selection indicator ENGLISH CONNECTIONS 1. Connect your line sources (CD players, MD players, etc.) and your turntables via the inputs for channels A + B -31-.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 25 5. Connect an MP3 player (for example) to the AUX input (3.5 mm jack) -38-. If you want to play tracks from your MP3 player via the mixer, the CD1/AUX input switch -37- has to be in the “AUX” position. If you want to play tracks from the CD player connected to channel A via your mixer, the CD1/AUX input switch -37- has to be in the “CD1” position. NOTE! The function described above is only available for channel A. 6.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 26 OPERATION 1. Power on [see designations; number 27] After having connected all necessary devices turn on the mixer via the ON/OFF switch -27-. 2.
IM_IQ2.qxp 10.07.2008 14:28 Uhr 7. Seite 27 Fader start [see designations; numbers 17, 21, 28 & 40] If you have connected two appropriate CD players to your Reloop IQ2+ (as described in chapter “connections”, point 7) it is possible to operate them by remote control using the crossfader -21- or the linefaders -17-.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 28 10. Monitoring [see designations; numbers 8, 9 & 11] With the CueMix fader -11- you can determine which signal you would like to monitor. If the CueMix fader -11- is in the outer left position (position “CHA”), you will hear the cue signal for channel A via your headphones; if the CueMix fader -11- is in the outer right position (position “CHB”), you will hear the cue signal for channel B via your headphones.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 29 NOTE! Via the separate TAP/BPM button -23- you can manually adjust the bars when effects are active. NOTE! The DSP effect unit is only available for use if the crossfader effect unit is turned off. To obtain this the fader effect switch -15- must be in the “OFF” position. ENGLISH 14.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 30 Depending on the effect, the time parameter's type and interval and the adjustments according to the beat assignment buttons -24-, will differ. • ECHO = echo effect Continuously repeats a certain interval of the signal. Time parameter value: 2 – 2000 msec Direct bar assignment: Intervals adjustable from 125 – 2000 By turning the X parameter knob -25- the value will be changed in steps of 1.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 31 • REVERB = reverb effect Simulates reflecting sound waves in a naturally restricted area. Time parameter value: 0 – 100% Direct bar assignment: 0/20/40/60/80/100% By turning the X parameter knob -25 the value will be changed in steps of 1. Push, hold and turn the X parameter knob -25- and the value will change in steps of 10.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 32 The following three crossfader effects are at your disposal: a.) LoopX Depending on the bar that has been adjusted via the X parameter knob -25or the beat assignment buttons for the DSP effect unit -24- (as described in the chapter “operation”, point 14) a loop can be created with this effect. The further the crossfader is being moved to the opposite side the lower the loop sequence will become.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 33 TECHNICAL INFORMATION Global Distribution GmbH did not test the following manufacturers’ specifications for plausibility and accuracy: Inputs: .....................................................2 x Phono, 2mV/47 kOhm; ...........................................................2(+2) x Line, 200mV/47 kOhm; ...........................................................1 x Mic, 2mV/10 kOhm; ...........................................................
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 34 MODE D'EMPLOI FRANÇAIS Nous vous félicitons d’avoir choisi la console de mixage Reloop IQ2+ / Reloop IQ2+ USB, preuve de la confiance que vous accordez à notre technologie pour Disc Jockey. Avant la mise en service, nous vous prions de lire attentivement ce mode d’emploi et de respecter les instructions pendant l’utilisation. Retirez la Reloop IQ2+ DSP / USB de son emballage. Avant la première mise en service, vérifiez le bon état de l’appareil.
IM_IQ2.qxp 10.07.2008 14:28 Uhr - - - - - - - Ne placez jamais des récipients de liquides susceptibles de se renverser sur l’appareil ou à proximité directe. En cas d’infiltration de liquides dans le boîtier, retirez immédiatement la fiche électrique. Faites contrôler l’appareil par un technicien qualifié avant de le réutiliser. La garantie exclu tous les dégâts dus aux infiltrations de liquides. N’utilisez pas l’appareil dans un environnement extrêmement chaud (plus de 35°C) ou froid (sous 5° C).
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 36 UTILISATION CONFORME - - - Cet appareil est une console de mixage professionnelle permettant de régler et d’enchaîner des signaux audio de bas niveau. La console doit être connectée entre la source de signal et un ampli audio. Ce produit est certifié pour le branchement sur secteur 240 V, 50 Hz tension alternative et est exclusivement conçu pour être utilisé en local fermé.
IM_IQ2.qxp 10.07.
IM_IQ2.qxp 10.07.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 39 DESCRIPTIONS FRANÇAIS 1. .............Bouton de réglage du volume du microphone 2. ...........Égaliseur 2 voies du microphone 3. ............Commutateur microphone-Talkover 4. ...........Régleur de gain canaux A + B 5. ...........Égaliseur 3 voies pour les canaux A + B 6. ...........Sélecteur de source du signal pour les canaux A + B ................(position USB uniquement pour Reloop IQ2+ USB) 7. ............Régleur rotatif Master Volume 8. ...........
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 40 DESCRIPTIONS ÉCRAN D'INFOS ACL -13- I V II IV III FRANÇAIS I. . . . . . .Affectation du canal II. . . . . . .BPM III. . . . . .Paramètre X IV. . . . . .Paramètre Y V . . . . . ..Sélection d'effet CONNECTIQUE 1. Raccorder les sources Line (lecteur de cédérom, MD, etc.) et votre platine vinyle avec les prises d'entrées pour les canaux A et B -31-.
IM_IQ2.qxp 10.07.2008 14:28 Uhr Seite 41 5. La prise d'entrée AUX (3,5 mm jack) -38- permet par exemple de raccorder un lecteur MP3. Pour restituer les pistes du lecteur MP3 via la console, le commutateur d'entrée CD1/AUX -37- doit être sur „AUX“. Si vous désirez restituer les pistes de votre lecteur de cédérom raccordé au canal A via la console de mixage, le commutateur d'entrée CD1/AUX -37- doit être sur „CD1“. NOTE ! La fonction plus haut décrite est alors uniquement disponible pour le canal A. 6.
IM_IQ2.qxp 10.07.2008 14:29 Uhr Seite 42 UTILISATION 1. Mise sous tension [voir Descriptions, n° 27] Après avoir effectué tous les branchements, veuillez allumer l'appareil avec l'interrupteur MARCHE/ARRÊT -27-. 2.
IM_IQ2.qxp 10.07.2008 14:29 Uhr 7. Seite 43 NOTE ! Consulter également les instructions relatives au démarrage curseur du mode d'emploi de votre lecteur de cédérom. Les instructions peuvent être différentes de celles plus haut décrites selon le modèle de lecteur de cédérom. 8. DJ-Mic [voir Descriptions, n° 1, 2 & 3] Le bouton de réglage du volume du microphone -1- sert à ajuster le niveau de sortie du canal DJ-Mic.
IM_IQ2.qxp 10.07.2008 14:29 Uhr Seite 44 FRANÇAIS 9. Saturation [voir Descriptions, n° 4, 5, 7,10, 17 & 42] Les DEL de saturation Cue/Master -12- indiquent le niveau de sortie pou les canaux A et B. Une barre numérotée de -24 à +14 est située entre les deux DEL.
IM_IQ2.qxp 10.07.2008 14:29 Uhr Seite 45 13. Compteur de battements [voir Descriptions, n° 13, 16 & 23] La console de mixage Reloop IQ2+ est équipée d'un compteur de battements automatique et d'un compteur de battements manuel. Le compteur de battements automatique est le réglage par défaut à l'allumage de la console. Sélectionner le canal dont les BPM doivent être comptés avec le régleur d'affectation pour effets -16- (la position A correspond au canal A ; la position B au canal B).
IM_IQ2.qxp 10.07.2008 14:29 Uhr Seite 46 Selon l'effet, le type et la plage du paramétrage de temps et les modifications effectuées par la touche d'affectation de tempo -24- diffèrent : • ECHO = effet Echo Répète plusieurs fois un intervalle déterminé du signal. Valeur de paramétrage de temps : 2 – 2000 mSec Affectation directe du tempo : intervalles de 125 – 2000 réglables Tourner le régleur rotatif du paramètre X -25- pour modifier la valeur par étapes de 1 unité.
IM_IQ2.qxp 10.07.2008 14:29 Uhr Seite 47 • REVERB = effet Reverb Simule des réflexions d'ondes sonores dans un espace naturellement limité. Valeur de paramétrage de temps : 0 – 100% Affectation directe du tempo : 0/20/40/60/80/100% Tourner le régleur rotatif du paramètre X -25- pour modifier la valeur par étapes de 1 unités. Enfoncer et tourner le régleur rotatif du paramètre X -25- pour modifier la valeur par étapes de 10 unités.
IM_IQ2.qxp 10.07.2008 14:29 Uhr Seite 48 Vous disposez des trois effets de Crossfader ci-dessous : a.) LoopX : cet effet génère une boucle selon le tempo auparavant réglé à l'aide du régleur rotatif du paramètre X -25- ou des touches d'affectation de tempo pour l'unité d'effets DSP -24- (comme décrit au chapitre Utilisation, paragraphe 14). Plus le Crossfader est déplacé vers le côté opposé, plus le volume de la séquence bouclée est faible.
IM_IQ2.qxp 10.07.2008 14:29 Uhr Seite 49 CARACTÉRISTIQUES La plausibilité et l'exactitude des données suivantes du fabricant ne sont pas contrôlées par la société Global Distribution GmbH : Entrées: ..................................................2 x Phono, 2mV/47 kohms ; ...........................................................2(+2) x Line, 200mV/47 kohms ; ........................................................... 1 x Mic, 2mV/10 kohms ; ...........................................................
NOTES IM_IQ2.qxp 50 10.07.
IM_IQ2.qxp 10.07.
IM_IQ2.qxp 10.07.2008 14:29 Uhr Seite 52 Reloop Distribution Global Distribution GmbH, Schuckertstr. 28, 48153 Münster/Germany Fax +49.251.