Bedienungsanleitung ACHTUNG! Lesen Sie sich vor der ersten Inbetriebnahme zur eigenen Sicherheit diese Bedienungsanleitung sorgfältig durch! Alle Personen, die mit der Aufstellung, Inbetriebnahme, Bedienung, Wartung und Instandhaltung dieses Gerätes zu tun haben, müssen entsprechend qualifiziert sein und diese Betriebsanleitung genau beachten.
BEDIENUNGSANLEITUNG ACHTUNG! Lesen Sie sich vor der ersten Inbetriebnahme zur eigenen Sicherheit diese Bedienungsanleitung sorgfältig durch! Alle Personen, die mit der Aufstellung , Inbetriebnahme, Bedienung, Wartung und Instandhaltung dieses Gerätes zu tun haben, müssen entsprechend qualifiziert sein und diese Betriebsanleitung genau beachten.
SICHERHEITSHINWEISE ACHTUNG! Seien Sie besonders vorsichtig beim Umgang mit der Netzspannung. Bei dieser Spannung können Sie einen lebensgefährlichen elektrischen Schlag erhalten! Bei Schäden, die durch Nichtbeachtung dieser Bedienungsanleitung verursacht werden, erlischt jeder Gewährleistungsanspruch. Bei Sach- oder Personenschäden, die durch unsachgemäße Handhabung oder Nichtbeachtung der Sicherheitshinweise verursacht werden, übernimmt der Hersteller keine Haftung.
- In Schulen, Ausbildungseinrichtungen, Hobby- oder Selbsthilfewerkstätten ist das Betreiben des Gerätes durch geschultes Personal verantwortlich zu überwachen. - Heben Sie diese Bedienungsanleitung für spätere Fragen und Probleme gut auf. BESTIMMUNGSGEMÄSSE VERWENDUNG Bei diesem Gerät handelt es sich um einen professionellen DJ MIDI Controller mit integrierter 6-In / 4-Out Soundkarte, mit dem sich Software steuern lässt. Das Gerät wird dabei mit einem USB Kabel am Computer angeschlossen.
Geräteoberseite Bezeichnung Shift Bezeichnung T01 Pitchfader Key T02 Dry/Wet-Regler Effektwechsel im Advanced-Effekt-Modus T03 Effektparameter Effektwechsel im Chained-Effekt-Modus T04 FX On-Taste FX Preset 1 T05 Effekt-Reset bzw. FX 1 On FX Preset 2 T06 Effekt-Taste 1 bzw. FX 2 On FX Preset 3 T07 Effekt-Taste 2 bzw.
1.2.
Geräteseite # Bezeichnung S69 Jog Wheel-Widerstand S70 Kensington-Lock 2. INBETRIEBNAHME - Schalten Sie das Gerät zunächst über den Ein/Aus-Schalter -B56- auf der Rückseite aus. - Verbinden Sie das beiliegende Netzteil mit der DC-Buchse -B55- des Gerätes. Stecken Sie nun den Netzadapter in eine freie Steckdose. - Verbinden Sie anschließend das mitgelieferte USB-Kabel mit dem Anschluss -B57- auf der Rückseite des Gerätes und einer freien USB-Schnittstelle an Ihrem Computer. 3.
2. Klicken Sie nun auf die Schaltfläche „Treiber installieren“. DEUTSCH 3. Sie werden anschließend aufgefordert, Reloop Jockey 3 anzustecken und einzuschalten. Sollte Reloop Jockey 3 noch nicht per USB verbunden sein, so schließen Sie das mitgelieferte USBKabel am USB-Port -B57- und an einem freien USB-Anschluss Ihres Computers an. Verbinden Sie ebenfalls das mitgelieferte Netzteil mit dem Netzteilanschluss -B55-. Schalten Sie nun das Gerät über den Ein/Aus-Schalter -B56- ein. 4.
Mit Reloop Jockey 3 erhalten Sie die kostenlose und uneingeschränkt verwendbare DJ-Software „Traktor LE“. HINWEIS! Upgrade auf Traktor Pro (4 Deck-Unterstützung): Mit Ihrer beiliegenden Traktor LE Version haben Sie den Vorteil, die umfangreiche Traktor PRO Version zum Vorzugspreis zu erwerben. Aktuelle Preiskonditionen erfahren Sie auf www.nativeinstruments.de 3.2.1. INSTALLATION DEUTSCH 3.2.
HINWEIS! Standardmäßig sollte das Audio-Setup auf den Internal-Mixing-Modus eingestellt sein. Sollte dies nicht der Fall sein, so beachten Sie die folgenden Punkte genau. Ansonsten können Sie dieses Kapitel überspringen und beim Kapitel „Bedienung“ fortsetzen. Audio Setup Internal-Mixing-Modus DEUTSCH 1. Öffnen Sie in Traktor den Einstellungsdialog, indem Sie auf das kleine Zahnrad am oberen, rechten Rand klicken. 2.
3. Öffnen Sie nun die Kategorie „Output Routing“ und wählen im Bereich „Mixing Mode“ die Schaltfläche „Internal“. Die Kanalzuweisung entnehmen Sie bitte folgendem Beispiel: DEUTSCH 3.3. TRAKTOR PRO-KONFIGURATION [GEGEBENENFALLS] Sollten Sie bereits Traktor Pro besitzen oder kostengünstig von der beiliegenden Traktor LE-Version upgegradet haben, so können alle Funktionen von Jockey 3 voll ausgeschöpft werden.
3.3.2. MAPPING-IMPORT Damit Traktor die MIDI-Befehle, die vom Jockey 3 gesendet werden, den richtigen Funktionen zuordnen kann, ist eine Befehlszuweisungstabelle, auch Mapping genannt, nötig. Eine passende Mapping-Datei finden Sie auf der Installations-CD im Ordner „Mappings/Traktor Pro“. HINWEIS! Stets aktualisierte und erweiterte Mappings finden Sie auch online. Surfen Sie dazu auf http:// www.reloopdj.com/forum und öffnen Sie die Kategorie „Mapping files“ im Bereich „Downloads for all Reloop products“.
4. Betätigen Sie nun die Schaltfläche „Add...“ und wählen „Import“. DEUTSCH Im Auswahlfenster öffnen Sie die Mapping-Datei, die sich auf der CD befindet oder gerade von der Reloop-Supportseite heruntergeladen wurde. Problembehebung Sollte ein Problem auftauchen, wobei die LEDs des Jockey 3 nicht ordnungsgemäß aufleuchten, so liegt es in den meisten Fällen an installierter MIDI-Software (z.B. MidiYoke, Maple Virtual MIDI cable, OSCulator, Bome Midi-Translator, etc.).
4. BEDIENUNG Nachdem der Reloop Jockey 3 angeschlossen und richtig in der DJ-Software Traktor konfiguriert wurde, kann diese nun bedient werden. Wird Traktor Pro verwendet, so kann die Jockey 3 Bedienoberfläche voll ausgeschöpft werden. Für Traktor LE ergeben sich, insbesondere für die Effektsteuerung, die Anzahl der verwendbaren Decks und die Hot Cue-Belegung einige Unterschiede. 4.1. TRAKTOR-FUNKTIONSBELEGUNG DEUTSCH HINWEIS! Im Folgenden wird die gesamte Traktor-Funktionsbelegung beschrieben.
Funktion Funktion bei aktivem Shift -T3- T8 Loop-Länge Drehen des Encoders variiert die Länge eines gesetzten Loops. Drücken des Encoders aktiviert bzw. deaktiviert die Loop Active-Funktion. T9 Loop verschieben Drehen des Encoders verschiebt einen gesetzten Loop. Drücken und gleichzeitiges Drehen des Encoders legt die Schrittweite der Bewegung fest. T10 Filter Reguliert den Filter-Effekt für das aktive Deck. In der Nullstellung wird der Filter automatisch deaktiviert.
DEUTSCH 16 Element Funktion Funktion bei aktivem Shift -T3- T21 Jog Wheel Modus-Tasten Es stehen insgesamt 4 Modi zur Verfügung, die die Funktion des Jog Wheels -T28- bestimmen: - SCRATCH Ist dieser Modus aktiv, so lässt sich der aktuelle Track scratchen, solange die Oberseite des Jog Wheel -T22- berührt wird. Wird nur die Seite berührt und das Jog Wheel bewegt, so lässt sich der laufende Track beschleunigen (Uhrzeigersinn) bzw. abbremsen (gegen den Uhrzeigersinn).
Funktion T30 Deck-Auswahl-Schalter Mit diesem Schalter werden die steuerbaren Decks angewählt. Ist der Schalter auf Input gestellt kann der Mixer als analoger Mixer verwendet werden. T31 Gain-Regler Mit diesem Regler lässt sich die Lautstärke des Decks einstellen. T32 EQ-Regler High Mit diesem Regler lassen sich die Höhen einstellen. T33 EQ-Regler Mid Mit diesem Regler lassen sich die Mitten einstellen. T34 EQ-Regler Low Mit diesem Regler lassen sich die Tiefen einstellen.
4.2. ROUTING-FUNKTIONEN Der Jockey 3 verfügt über verschiedene Routing-Möglichkeiten, um vorhandenes Equipment einbinden zu können. 4.2.1.MIKROFON Auf der Gerätevorderseite kann ein Mikrofon über einen 6,3 mm Klinkenstecker eingebunden werden -F45-. Neben einem Volume-Regler -46- ist ein Routing-Schalter -47- enthalten, der folgende Routing-Optionen für das Mirkofon steuert: SW = Das Mikrofon-Signal wird zur Software geroutet. Für diese Funktion ist ein freies Deck für das Mikrofon-Signal notwendig.
Um das Signal über den Master hörbar zu machen muss das Deck nun noch auf Audio-Thru gestellt werden. Thru = Das Mikrofon-Signal wird direkt auf den Master-Ausgang geroutet. Bei dieser Variante wird kein Kanal in der Software benötigt und eignet sich daher sehr gut für User der Traktor LE Version oder bei der Verwendung von vier Decks in Traktor Pro. Off= Das Mikrofon wird stumm geschaltet. 4.2.2.
DEUTSCH Zunächst müssen in den Einstellungen die richtigen Inputs für das entsprechende Deck gewählt werden. Im Beispiel wird Deck C als analoger Kanal verwendet. Um das Signal über den Master hörbar zu machen muss das Deck nun noch auf Audio-Thru gestellt werden. Um das Signal über den Mixer zu steuern muss der Deck-Auswahl-Schalter auf C gestellt sein. Durch die Verwendung dieser Routig-Option kann das Input-Signal mit den Traktor-internen Effekten aufgewertet werden.
IN1 = Mix Ist das Input-Routing auf MIX geschaltet, so wird das Input-Signal direkt auf den Mixer geroutet. Wird der Deck-Auswahl-Schalter -30- auf IN1 gesetzt, werden die beiden Decks A und C in Traktor stumm geschaltet. Lediglich das analoge Signal ist zu hören. IN1 = Off IN1 wird stumm geschaltet 4.3. ANALOG-MIXING-FUNKTION Der Jockey III kann ebenfalls als Zwei-Kanal-Mixer ohne die Einbindung eines Computers genutzt werden. Zu diesem Zweck müssen beide Deck-Auswahl-Schalter -T30- auf IN1 bzw.
5.1.1. MIDI-CHANNEL-ZUWEISUNG ACHTUNG! Standardmäßig ist der Jockey 3 auf die MIDI-Kanäle 1-4 konfiguriert. Deck A ist dabei auf dem 1., Deck B auf dem 2., Deck C auf dem 3. und Deck D auf dem 4. Kanal. Die offiziellen Mappings seitens Reloop sind auf die standardmäßige Konfiguration ausgelegt. Eine Veränderung ist damit im Normalfall nicht notwendig. Sollten Sie dennoch vorhaben, die Decks auf die MIDI-Kanal-Kombinationen 5-8, 9-12 oder 13-16 legen zu wollen, gehen Sie wie folgt vor: 1.
5.3. AUTO-SETUP Hiermit können Sie ein Auto-Setup durchführen. Das Auto-Setup dient zur Problembehebung und sollte durchgeführt werden, wenn der Jockey 3 nicht richtig reagieren sollte. 1. Stellen Sie sicher, dass der Jockey 3 ausgeschaltet ist (siehe Stellung Ein/Aus-Schalter -B56-). 2. Halten Sie die rechte Play-Taste -T27- gedrückt und schalten Sie den Jockey 3 durch Umlegen des Ein/Aus-Schalters -B56- ein. 3. Lassen Sie nun die Play-Taste -T27- los. 4. Das Auto-Setup wird nun durchgeführt. 5.
Durchführen eines Firmware-Updates DEUTSCH 1. Stellen Sie sicher, dass der Jockey 3 ausgeschaltet (siehe Stellung Ein/Aus-Schalter -B56-) und per USB-Kabel am Rechner angeschlossen ist. 2. Halten Sie die rechte CUP-Taste -T25- und die rechte CUE-Taste -T26- gedrückt und schalten Sie den Jockey 3 durch Umlegen des Ein/Aus-Schalters -B56- ein. 3. Lassen Sie nun beide Tasten los. 4. Die obersten LEDs des VU-Meter blinken nun auf. Der Jockey 3 befindet sich im Update-Modus. 5.
8. N achdem das Update erfolgreich abgeschlossen ist beenden Sie das Firmware-Update-Tool und starten den Jockey 3 über den Ein/Aus-Schalter -B56- neu. 6.2. TREIBER-UPDATE Speziell für das integrierte Audio-Interface werden ebenfalls aktualisierte Treiber angeboten, die heruntergeladen werden können. 6.3. MAPPINGS Auch werden für Traktor Pro Nachfolgeversionen und andere DJ-Softwares stets aktualisierte Mappings bereitgestellt, damit Sie den Reloop Jockey 3 auch in Zukunft verwenden können.
DEUTSCH 26 SW name Type MIDI MIDI 2 (Shift) Remarks JOG CCW SW 24 63 SCRATCH LED = ON & No Touch Inner Wheel KEY PITCHBEND/VR PitchBend 2C GAIN VR 2D 6C HIGH VR 2E 6D MID VR 2F 6E LOW VR 30 6F CH FADER VR 31 70 FILTER VR/CENTER 32/32 71/71 PAN VR/CENTER 33/33 72/72 CUE/MASTER FADER VR 36 -- CH1 Only CROSSFADER VR 37 -- CH1 Only FX ON SW/LED 01/01 40/01 RST SW/LED 02/02 41/02 FX B1 SW/LED 03/03 42/03 FX B2 SW/LED 04/04 43/04 LOOP SW/LED 0
CC-ABSOLUTE (VR) Control Change messages are sent with status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number. The value from 0x00 to 0x7F, directly related to the location of the controller. CC-RELATIVE (ENC) Control Change messages are status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number.
7.3. TIPPS ZUR FEHLERBEHEBUNG Sollten Probleme bei der Benutzung von Reloop Jockey 3 auftreten, so ist dies Ihre erste Anlaufstelle, um diese zu beheben: DEUTSCH Symptome Mögliche Ursachen Überprüfen Sie, ob das USB-Kabel richtig mit einem USB-Port Ihres Computers und mit dem Jockey 3 USB-Port -B69- verbunden ist. Bitte prüfen Sie ebenfalls, ob das Steckernetzteil korrekt an dem Netzanschluss -B54- angeschlossen ist. Die LEDs des Controllers leuchten nur schwach auf und das Gerät reagiert nicht.
7.4. TECHNISCHE DATEN Folgende Daten des Herstellers werden von der Global Distribution GmbH nicht auf Plausibilität und Richtigkeit geprüft: Allgemeine Daten Stromquelle: . . . . . . . . . . . . . . . . . . . . . USB 5V 500mA / DC: 6V, 2A; Maße: . . . . . . . . . . . . . . . . . . . . . . . . . . . 420 x 315 x 61,55 mm Gewicht: . . . . . . . . . . . . . . . . . . . . . . . . . 5 kg USB 2. USB Slave Player Sektion: (Signal Format: MP3, 128kbps, Sony Sound Forge 8.0) 2.
DEUTSCH
INSTRUCTION MANUAL CAUTION! For your own safety, please read this operation manual carefully before initial operation! All persons involved in the installation, setting-up, operation, maintenance and service of this device must be appropriately qualified and follow this operation manual in detail. This product complies with the requirements of the applicable European and national regulations. Conformity has been proven. The respective statements and documents are deposited at the manufacturer.
SAFETY INSTRUCTIONS ENGLISH CAUTION! Please exercise particular caution when handling power voltage. This voltage rating may lead to a critical electrical shock! Any damage caused by the non-observance of this operation manual excludes any warranty claims. The manufacturer is not liable for any damage to property or for personal injury caused by improper handling or non-observance of the safety instructions. 32 - This device has left the factory in perfect condition.
APPLICATION IN ACCORDANCE WITH REGULATIONS - This device is a professional DJ MIDI controller with integrated 6-In / 4-Out soundcard that can control software. The device should be connected via USB cable to a computer. - This product is authorised for connection to 240 V, 50 Hz AC via the included mains adapter and is designed exclusively for indoor application.
ENGLISH Surface 34 # Designation Shift Designation T01 Pitchfader Key T02 Dry/Wet Control Effect change in Advanced Effect Mode T03 Effektparameter Effect change in Chained Effect Mode T04 FX On Button FX Preset 1 T05 Effect Reset and FX 1 On respectively FX Preset 2 T06 Effect Button 1 and FX 2 On respectively FX Preset 3 T07 Effect Button 2 and FX 3 On respectively T08 Loop Length T09 Loop Shift T10 Filter T11 Pan(Balance) Control T12 Pitch Bend Button – FX 1 T13 Pitch
1.2. CONNECTIONS B65 B54 B58 B55 F46 B56 B59 B60 B61 B62 B63 B64 B65 B66 B67 B65 B57 F47 F48 F49 F52 F50 F51 F45 # Designation B54 Mains Cord Strain Relief B55 Mains Adapter Connection (DC 6V/1,5A) B56 ON/OFF Switch B57 USB Port B58 Jog Wheel Sensitivity B59 LED Dimmer B60 Shift Lock Switch B61 3.5 mm Jack Master-Thru Input B62 6.
Lateral View # Designation S69 Jog Wheel Drag S70 Kensington Lock 2. INITIAL OPERATION - First make sure to turn off the device via the ON/OFF Button -B56- on the rear panel. - Connect the included mains adapter to the device‘s DC jack -B55- and a shock-proof outlet. - Then connect the included USB cable to the corresponding connection -B57- on the device‘s rear panel and a free USB port of your computer. 3.
2. Now click on the „Install the driver“ button. 3. You will then be asked to connect and turn on your Reloop Jockey 3. If your Reloop Jockey 3 is not connected via USB yet, please connect the included USB cable to the USB port -B57- and a free USB port of your computer. Also connect the included mains adapter to the corresponding connector -B55-. Now turn on the device via the ON/Off Button -B56-. ENGLISH 4. The installation will be continued.
ENGLISH 3.2 TRAKTOR LE SETUP Along with Reloop Jockey 3 you receive the gratuitous and non-restrictive DJ software „Traktor LE“. NOTE! Upgrade to Traktor Pro (4 deck support): Via the included Traktor LE version you can purchase the extensive Traktor Pro version at a bargain price. Current price conditions can be found under www.nativeinstruments.de 3.2.1 INSTALLATION Besides the ASIO drivers, you can also find a directory named „Traktor“ on the included installation CD.
NOTE! By default the audio setup should be adjusted to internal mixing mode. If this is not the case, please pay close attention to the following items. Otherwise you can skip this chapter and continue with the chapter „Operation“. Audio Setup: Internal Mixing Mode 1. In Traktor open the setup dialogue by clicking the small cog wheel in the upper right corner. 2. Open the catagory „Audio Setup“ and in the filed „Audio Device“ select the item „Reloop Jockey 3“.
ENGLISH 3. Open the category „Output Routing“ and in the field „Mixing Mode“ select the button „Internal“. For channel assignment please see the following example. 3.3 TRAKTOR PRO CONFIGURATION (IF APPLICABLE) If you already possess Traktor Pro or you have upgraded Traktor LE at a lower-cost price, it is possible to fully utilize all Jockey 3 functions. Pay close attention to the following points in order for Traktor to be able to work in combination with Jockey 3. 3.3.
3.3.2 MAPPING IMPORT In order for Traktor to be able to assign the MIDI commands sent by the Jockey 3 to the correct functions, a special mapping is necessary. A suitable mapping can be found on the installation CD in the folder „Mappings/Traktor Pro“. NOTE! You can find updated and extended mappings online. Go to http://www.reloopdj.com/forum and open the category „Mapping files“ in the field „Downloads for all Reloop products“. Please proceed as follows in order to import the mapping: 1.
ENGLISH 4. Now select the button „Add...“ followed by „Import“. In the select screen open the mapping file that is found on the CD or that was downloaded from the Reloop support site. Troubleshooting Should a problem arise and the Jockey 3‘s LEDs are not lit correctly, in most cases this is probably caused by installed MIDI software (e.g. MidiYoke, Maple Virtual MIDI Cable, OSCulator, Bome Midi Translator etc.). In order to solve the problem proceed as follows: 1.
4. OPERATION After connecting and configuring Reloop Jockey 3 correctly for the DJ software, Traktor can now be used. If Traktor Pro is used, it is possible to fully utilize the Jockey 3 user interface. There are some differences for Traktor LE regarding effect control, the number of usable decks and the hot cue assignment. 4.1 TRAKTOR FUNCTION ASSIGNMENT NOTE! In the following the whole Traktor function assignment will be described.
ENGLISH 44 Element Funktion Funktion bei aktivem Shift -T3- T10 Filter Adjusts the filter effect for the active deck. In zero position the filter is automatically turned off. T11 Pan Dial Herewith it is possible to adjust the volume assignment for the left and right channel. Zero position corresponds to an equal level on both channels. T12 Pitchbend Button Slows down the deck‘s pitch. FX Routing Button 1 Herewith it is possible to assign FX Unit 1 to the current deck.
Funktion Funktion bei aktivem Shift -T3- T21 Jog Wheel Mode Buttons There are 4 modes at your disposal which determine the jog wheel‘s function. - SCRATCH If this mode is active, it is possible to scratch the current track as long as the jog wheel‘s -T22- surface is being touched. If only the side is being touched, the current track‘s pitch can be increased (clockwise) or decreased (counterclockwise).
ENGLISH 46 Element Funktion T31 Gain Dial With this dial it is possible to adjust the deck‘s volume. T32 EQ Dial High Via this dial the high frequencies can be adjusted. T33 EQ Dial Mid Via this dial the middle frequencies can be adjusted. T34 EQ Dial Low Via this dial the low frequencies can be adjusted. T35 Cue Monitor Via this button it is possible to monitor the selected deck. T36 Linefader Via the linefader the channel‘s volume can be adjusted.
4.2 ROUTING FUNCTIONS The Jockey 3 disposes of various routing options in order to include already existing equipment. 4.2.1 MICROPHONE On the device‘s front panel a microphone can be included via a 6.3 mm jack -F45-. Besides a volume dial -46- there is also a Routing Switch -47- that operates the following routing options: SW = The microphone‘s signal is routed to the software. For this function a free deck for the mic signal is necessary.
In order to make the signal become audible via master, the deck has to be switched to Audio Thru. ENGLISH By using this routing option the mic signal can be enhanced with Traktor‘s internal effects. Thru = The mic‘s signal is directly routed to the master output. With this variant a signal in the software is not necessary, thus becoming especially adequate for Traktor LE users or when using four decks in Traktor Pro. Off = The mic becomes mute. 4.2.
First the correct inputs for the corresponding deck have to be selected. In this example deck C is used as analog channel. ENGLISH In order to make the signal become audible via Master, the deck has to be switched to Audio Thru. In order to operate the signal via the mixer the Deck Select Switch has to be put to C. By using this routing option the input signal can be enhanced with the internal Traktor effects.
IN1 = Mix If the Input Routing is switched to MIX, the input signal will be routed directly to the mixer. If the Deck Select Switch -30- is switched to IN1 both decks A and C in Traktor are mute. Only the analog signal is audible. IN1 = Off IN1 is switched to mute. 4.3 ANALOG MIXING FUNCTION The Jockey 3 can also be used as 2 channel mixing console without the necessity to involve a computer. To do so both Deck Select Switches -T30- have to be switched to IN1 and IN2 respectively.
5.1.1 MIDI CHANNEL ASSIGNMENT NOTE! By default the Jockey 3 is configured for MIDI channels 1-4. Deck A is assigned to channel 1, Deck B is assigned to channel 2, Deck C is assigned to channel 3 and Deck D is assigned to channel 4. Reloop‘s official mappings are laid out for the standard configuration. An adjustment is usually not necessary. However, if you wish to switch the decks to the MIDI channel combinations 5-8, 9-12 or 13-16, please proceed as follows: 1.
5.3 AUTO SETUP Herewith it is possible to carry out an auto setup. The auto setup is used to solve problems and should be carried out in case the Jockey 3 does not work correctly. 1. 2. 3. 4. 5. Make sure that the Jockey 3 is turned off (see position On/Off Button -B56-). Press and hold the right Play Button -T27- and turn on the Jockey 3 via the On/Off Button -B56-. Now release the Play Button -T27-. The auto setup will now be carried out.
How to carry out a firmware update 1. Make sure that the Jockey 3 is turned off (see position On/Off Button -B56-) and connected via USB to your computer. 2. Press and hold the right CUP Button -T25- and the right CUE Button -T26- and simultaneously turn on the Jockey 3 via the On/Off Button -B56-. 3. Now release both buttons. 4. Now the upper LEDs of the UV meter blink. The Jockey 3 is now in update mode. 5.
8. After the successful update exit the firmware update tool and reboot your Jockey 3 via the On/ Off Button -B56-. 6.2 DRIVER UPDATE Updated drivers for the integrated audio interface that can be downloaded are also offered. 6.3 MAPPINGS Follow-up versions for Traktor Pro and other DJ softwares Updated mappings for follow-up versions of Traktor Pro and other DJ softwares are also always provided, so that the Jockey 3 can also be utilized in the future.
Type MIDI MIDI 2 (Shift) Remarks JOG CCW SW 24 63 SCRATCH LED = ON & No Touch Inner Wheel KEY PITCHBEND/VR PitchBend 2C GAIN VR 2D 6C HIGH VR 2E 6D MID VR 2F 6E LOW VR 30 6F CH FADER VR 31 70 FILTER VR/CENTER 32/32 71/71 PAN VR/CENTER 33/33 72/72 CUE/MASTER FADER VR 36 -- CH1 Only CROSSFADER VR 37 -- CH1 Only FX ON SW/LED 01/01 40/01 RST SW/LED 02/02 41/02 FX B1 SW/LED 03/03 42/03 FX B2 SW/LED 04/04 43/04 LOOP SW/LED 05/05 44/05 RELOOP
CC-ABSOLUTE (VR) Control Change messages are sent with status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number. The value from 0x00 to 0x7F, directly related to the location of the controller. CC-RELATIVE (ENC) Control Change messages are status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number.
7.3 TROUBLESHOOTING If any problem should arise while using Reloop Jockey 3 the following chart is the first drop-in center: Possible Causes Corrective Measures The device does not receive any power when turning it on via the ON/ OFF Button -B56-. USB cord or mains adapter are not connected correctly. Check whether the USB cord is connected correctly to a free USB port of your computer and Jockey 3‘s USB port -B69-.
7.4 TECHNICAL SPECIFICATIONS The following specifications are not verified by Global Distribution GmbH in terms of plausibility and accuracy: 1. General Section Power Source: . . . . . . . . . . . . . . . . . . . . USB 5V 500mA / DC: 6V, 2A; Dimensions: . . . . . . . . . . . . . . . . . . . . . 420 x 315 x 61.55 mm Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . 5 kg USB 2. USB Slave Player Sektion: (Signal Format: MP3, 128kbps, Sony Sound Forge 8.0) 2.
ENGLISH 59
MODE D´EMPLOI ACHTUNG! Lesen Sie sich vor der ersten Inbetriebnahme zur eigenen Sicherheit diese Bedienungsanleitung sorgfältig durch! Alle Personen, die mit der Aufstellung , Inbetriebnahme, Bedienung, Wartung und Instandhaltung dieses Gerätes zu tun haben, müssen entsprechend qualifiziert sein und diese Betriebsanleitung genau beachten.
CONSIGNES DE SÉCURITÉ ATTENTION ! Soyez particulièrement vigilant lors des branchements avec la tension secteur 240 V. Une décharge électrique à cette tension peut être mortelle ! La garantie exclu tous les dégâts dus au non-respect des instructions de ce mode d’emploi. Le fabricant décline toute responsabilité pour les dégâts matériels et personnels dus à un usage incorrect ou au non-respect des consignes de sécurité. FRANÇAIS - Cet appareil a quitté l’usine de fabrication en parfait état.
UTILISATION CONFORME - Cet appareil est un contrôleur MIDI professionnel avec carte son intégrée à 6-In / 4-Out permettant de commander le logiciel. L’appareil doit pour cela être raccordé à un ordinateur par un câble USB. - Ce produit est certifié pour le branchement sur secteur 240 V, 50 Hz tension alternative et est exclusivement conçu pour être utilisé en local fermé. - Toute utilisation non conforme peut endommager le produit et annuler les droits de garantie.
Face supérieure de l‘appareil Désignation Désignation 2ème fonction (touche Maj) T01 Pitchfader Key T02 Régleur Dry/Wet Changement d'effet en mode d'effets Advanced T03 Paramètre d'effet Changement d'effet en mode d'effets Chained T04 Touche FX On FX Preset 1 T05 Reset effet ou FX 1 On FX Preset 2 T06 Touche d'effet 1 ou FX 2 On FX Preset 3 T07 Touche d'effet 2 ou FX 3 On FX Preset 4 T08 Longueur de boucle T09 Décalage de boucle T10 Filter T11 Régleur Pan(Balance) T12 Touche
1.2. CONNECTIQUE B65 B54 B58 B55 F46 B56 B59 B60 B61 B62 FRANÇAIS B64 B65 B66 B67 B65 B57 F47 F48 F49 F52 F50 F51 F45 Face arrière de l‘appareil # Désignation B54 Décharge de traction du câble secteur B55 Connecteur du bloc secteur (DC 6 V/1,5 A) B56 Interrupteur marche/arrêt B57 Port USB B58 Sensibilité de la Jog-Wheel B59 Variateur à DEL B60 Touche Verr.
Face de l‘appareil # Désignation S69 Résistance de la Jog-Wheel S70 Kensington-Lock 2. MISE EN SERVICE - Commencer par éteindre l‘appareil avec l‘interrupteur marche/arrêt -B56- situé sur la face arrière. - Brancher le cordon secteur fourni dans la prise DC -B55- de l‘appareil. Brancher à présent l‘adaptateur secteur dans une prise de courant libre. - Raccorder ensuite le câble USB fourni au port -B57- situé sur la face arrière de l‘appareil et à un port USB libre de votre ordinateur. 3.
2. Cliquer ensuite sur le bouton „Installer le pilote“. FRANÇAIS 3. L‘écran d‘installation vous demande alors de connecter et d‘allumer votre Reloop Jockey 3. Si votre Reloop Contour n‘est pas encore raccordé via USB, brancher le câble USB livré au port USB -B57- de votre Jockey 3 et à un port USB libre de votre ordinateur. Brancher également le bloc d‘alimentation fourni sur le connecteur du bloc secteur -B55-. Allumer ensuite l‘appareil avec l‘interrupteur marche/arrêt -B56-. 4.
Votre Reloop Jockey 3 est livré avec une version complète et gratuite du logiciel pour DJ „Traktor LE“. NOTE! Mise à niveau Traktor Pro (prise en charge de 4 platines) : votre présente version Traktor LE offre l‘avantage de pouvoir acheter la version Traktor PRO complète à un prix préférentiel. Vous pouvez consulter les prix sur le site www.nativeinstruments.de 3.2.1 INSTALLATION Outre le répertoire des pilotes ASIO, le cédérom d‘installation ci-joint comporte également le répertoire „Traktor“.
NOTE! Par défaut, la configuration audio doit être réglée sur le mode Internal Mixing. Si cela n‘est pas le cas veuillez lire attentivement les instructions ci-dessous. Autrement, vous pouvez passer ce chapitre et reprendre la lecture du manuel au chapitre „Utilisation“. Configuration audio : Mode Internal Mixing FRANÇAIS 1. Ouvrir le dialogue de réglage de Traktor en cliquant sur la petite roue dentée en haut sur le côté droit de la fenêtre. 2.
3. Ouvrir ensuite la rubrique „Output Routing“ et sélectionner le bouton „Internal“ pour „Mixing Mode“. Consulter l‘exemple ci-dessous pour l‘affectation des canaux : FRANÇAIS 3.3 CONFIGURATION TRAKTOR PRO [LE CAS ÉCHÉANT] Si vous possédez déjà Traktor Pro ou avez effectué la mise à niveau de la version Traktor LE ci-jointe, vous pouvez profiter sans restriction de toutes les fonctions de votre Jockey 3. Veuillez lire attentivement ce qui suit pour assurer le bon fonctionnement de Traktor avec Jockey 3.
3.3.2 IMPORTATION DE MAPPAGE La table d‘affectation des commandes, dénommée mappage, est nécessaire pour que le logiciel Traktor affecte correctement les commandes MIDI envoyées par la console Jockey 3 aux fonctions respectives. Le fichier de mappage adéquat se trouve sur le cédérom d‘installation dans le répertoire „Mappings/ Traktor Pro“. NOTE! Vous trouverez également les mappages actuels et améliorés sur notre site http://www.reloopdj.
4. Cliquer à présent sur le bouton „Add...“ et sélectionner „Import“. FRANÇAIS Dans la fenêtre de sélection, ouvrir le fichier de mappage situé sur le cédérom ou téléchargé du site Reloop. Dépannage Si un problème survient et que les DEL de la console Jockey 3 ne s‘allument pas correctement, la panne vient généralement du logiciel MIDI installé (par ex. MidiYoke, Maple Virtual MIDI cable, OSCulator, Bome Midi-Translator, etc.). Procéder comme suit pour le dépannage : 1.
4. UTILISATION Maintenant que votre console Reloop Jockey 3 est correctement raccordée et configurée dans le logiciel Traktor, vous pouvez l‘utiliser. Si Traktor Pro est utilisé, l‘interface de commande Jockey 3 peut être exploitée sans restrictions. Par contre, il existe quelques différences pour Traktor LE, spécialement concernant la commande des effets, le nombre de platines utilisables et l‘affectation Hot Cue. 4.
Fonction Fonction avec touche Maj enfoncée : -T23- T9 Décalage de boucle Tourner l‘Encoder pour décaler une boucle définie. Enfoncer et tourner simultanément l‘Encoder pour définir la longueur de pas du déplacement. T10 Filter Règle l‘effet Filter pour la platine active. En position zéro, le filtre est désactivé automatiquement. T11 Régleur Pan (Balance) Sert à régler la répartition du volume sur les canaux gauche et droite. La position zéro correspond à un niveau identique sur les deux canaux.
FRANÇAIS 74 Élément Fonction Fonction avec touche Maj enfoncée : -T23- T21 Touches de mode Jog Wheel Vous disposez au total de 4 modes pour définir la fonction de la Jog Wheel -T28- : - SCRATCH Lorsque ce mode est actif, vous pouvez scratcher la piste actuelle en touchant la surface de la Jog Wheel -T22-. Saisir uniquement le côté et tourner la Jog Wheel pour accélérer la piste en lecture (rotation à droite) ou la freiner (rotation à gauche).
Fonction T30 Sélecteur de platine Permet de sélectionner les platines commandables. Si le sélecteur est sur Input, la console peut être utilisée en tant que console de mixage analogique. T31 Gain-Regler Mit diesem Regler lässt sich die Lautstärke des Decks einstellen. T32 Gain Dial With this dial it is possible to adjust the deck‘s volume. T33 EQ Dial High Via this dial the high frequencies can be adjusted. T34 EQ Dial Low Via this dial the low frequencies can be adjusted.
4.2 FONCTIONS DE ROUTAGE Le Jockey 3 dispose de diverses possibilités de routage pour pouvoir raccorder un équipement existant. 4.2.1 MICROPHONE La face avant permet le branchement d‘un micro avec une fiche jack 6,3 mm -F45-. À côté d‘un régleur de volume -46- se trouve un sélecteur de routage -47- permettant de définir les options de routage suivantes pour le microphone : SW = Signal du microphone routé par le logiciel. Cette fonction requiert une platine libre pour le signal du micro.
Pour que le signal soit audible par le Master, il faut aussi régler la platine sur Audio-Thru. L‘utilisation de cette option de routage permet de transformer le signal du microphone avec les effets internes de Traktor. Off= Le microphone est coupé. 4.2.2 ENTRÉES Les deux entrées 1 et 2 peuvent au choix être routées vers le logiciel (SW) ou vers la sortie Master (MIX) avec les sélecteurs de routage -F49- et -F50-. La position Off désactive les entrées.
FRANÇAIS commencer par sélectionner les entrées correctes pour la platine respective dans les réglages. Dans l‘exemple, la platine C est utilisée en tant que canal analogique. Pour que le signal soit audible par le Master, il faut aussi régler la platine sur Audio-Thru. Pour commander le signal par la console de mixage, le sélecteur de platine doit être réglé sur C. L‘utilisation de cette option de routage permet de transformer le signal d‘entrée avec les effets internes de Traktor.
IN1 = Mix Si le routage d‘entrée est commuté sur MIX, le signal d‘entrée est directement routé vers la console de mixage. Si le sélecteur de platine -30- est réglé sur IN1, le son des deux platines A et C est coupé dans Traktor. Seul le signal analogique est audible. IN1 = Off IN1 est coupé 4.3 FONCTION DE MIXAGE ANALOGIQUE Le Digital Jockey III peut aussi être utilisé en tant que console deux canaux sans raccordement d‘un ordinateur.
5.1.1 AFFECTATION DES CANAUX MIDI ATTENTION ! Par défaut, Jockey 3 est configuré sur les canaux MIDI 1 à 4. La platine A est alors affectée au canal 1, la platine B au canal 2, la platine C au canal 3 et la platine D au canal 4. Les mappages officiels fournis par Reloop sont conçus pour la configuration par défaut. Normalement, il n‘est donc pas nécessaire de les modifier. Si cependant vous désirez configurer les platines sur les combinaisons de canaux MIDI 5 à 8, 9 à 12 ou 13 à 16, procédez comme suit.
5.3 AUTO-SETUP Permet d‘effectuer un Auto-Setup. La configuration automatique sert au dépannage et ne doit être exécutée que si le Jockey 3 ne répond plus. 1. 2. 3. 4. 5. Vérifier que le Jockey 3 est éteint (voir position de l‘interrupteur marche/arrêt -B56-). Enfoncer la touche droite Play-T27- et allumer le Jockey 3 en commutant l‘interrupteur marche/arrêt -B56-. Relâcher ensuite la touche Play -T27-. Auto-Setup est alors exécuté.
Mise à jour du micrologiciel FRANÇAIS 1. Vérifier que votre Jockey 3 est éteint (voir Position de l‘interrupteur marche/arrêt -B56-) et connecté à l‘ordinateur via le câble USB. 2. Enfoncer la touche droite CUP -T25- et la touche droite CUE -T26- et allumer le Jockey 3 en commutant l‘interrupteur marche/arrêt -B56-. 3. Relâcher ensuite les deux touches. 4. Les DEL supérieures du vumètre clignotent. Le Jockey 3 est alors en mode de mise à jour. 5.
8. A près l‘exécution correcte de la mise à jour, quitter l‘outil de mise à jour du micrologiciel, puis éteindre et rallumer votre Jockey 3 avec l‘interrupteur marche/arrêt -B56-. 6.2 MISE À JOUR DU PILOTE Plus spécialement pour l‘interface audio intégrée sont également proposés des pilotes actuels qui peuvent être téléchargés. 6.
FRANÇAIS 84 SW name Type MIDI MIDI 2 (Shift) Remarks JOG CCW SW 24 63 SCRATCH LED = ON & No Touch Inner Wheel KEY PITCHBEND/VR PitchBend 2C GAIN VR 2D 6C HIGH VR 2E 6D MID VR 2F 6E LOW VR 30 6F CH FADER VR 31 70 FILTER VR/CENTER 32/32 71/71 PAN VR/CENTER 33/33 72/72 CUE/MASTER FADER VR 36 -- CH1 Only CROSSFADER VR 37 -- CH1 Only FX ON SW/LED 01/01 40/01 RST SW/LED 02/02 41/02 FX B1 SW/LED 03/03 42/03 FX B2 SW/LED 04/04 43/04 LOOP SW/LED
CC-ABSOLUTE (VR) Control Change messages are sent with status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number. The value from 0x00 to 0x7F, directly related to the location of the controller. CC-RELATIVE (ENC) Control Change messages are status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number.
7.3 CONSEILS DE DÉPANNAGE FRANÇAIS Si vous avez des problèmes lors de l‘utilisation de votre Reloop Jockey 3, consultez cette ressource en premier recours pour dépanner : 86 Symptoms Possible Causes Corrective Measures The device does not receive any power when turning it on via the ON/ OFF Button -B56-. USB cord or mains adapter are not correctly connected. Check whether the USB cord is correctly connected to a free USB port of your computer and Jockey 3‘s USB port -B69-.
7.4 CARACTÉRISTIQUES La plausibilité et l’exactitude des données suivantes du fabricant ne sont pas contrôlées par la société Global Distribution GmbH : Caractéristiques generals Alimentation électrique . . . . . . . . . . . . USB 5V 500mA / DC: 6V, 2A; Dimensions: . . . . . . . . . . . . . . . . . . . . . . 420 x 315 x 61,55 mm Poids: . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 kg USB 2. Section USB Slave Player: (Signal Format: MP3, 128kbps, Sony Sound Forge 8.0) 2.
FRANÇAIS
WWW.RELOOPDJ.COM Reloop Trademark Global Distribution GmbH Schuckertstr. 28 48153 Muenster / Germany © Copyright 2009 Nachdruck Verboten! Unbenannt-3 1 19.05.