Bedienungsanleitung ACHTUNG! Lesen Sie sich vor der ersten Inbetriebnahme zur eigenen Sicherheit diese Bedienungsanleitung sorgfältig durch! Alle Personen, die mit der Aufstellung, Inbetriebnahme, Bedienung, Wartung und Instandhaltung dieses Gerätes zu tun haben, müssen entsprechend qualifiziert sein und diese Betriebsanleitung genau beachten.
BEDIENUNGSANLEITUNG ACHTUNG! Lesen Sie sich vor der ersten Inbetriebnahme zur eigenen Sicherheit diese Bedienungsanleitung sorgfältig durch! Alle Personen, die mit der Aufstellung , Inbetriebnahme, Bedienung, Wartung und Instandhaltung dieses Gerätes zu tun haben, müssen entsprechend qualifiziert sein und diese Betriebsanleitung genau beachten.
DEUTSCH - Die Sicherung darf nur gegen Sicherungen des gleichen Typs, der gleichen Auslösecharakteristik und Nennstromstärke ausgetauscht werden. - Stellen Sie sicher, dass die Stromversorgung erst nach dem Aufbau des Gerätes erfolgt. Den Netzstecker immer als letztes einstecken. Vergewissern Sie sich, dass der Netzschalter auf „OFF“ steht, wenn Sie das Gerät ans Netz anschließen. - Benutzen Sie nur vorschriftsmäßige Kabel.
WARTUNG -Ü berprüfen Sie regelmäßig die technische Sicherheit des Gerätes auf Beschädigungen des Netzkabels oder des Gehäuses, sowie auf die Abnutzung von Verschleißteilen wie Dreh- und Schiebereglern. -W enn anzunehmen ist, dass ein gefahrloser Betrieb nicht mehr möglich ist, so ist das Gerät außer Betrieb zu setzten und gegen unbeabsichtigten Betrieb zu sichern.
1.1 BEDIENELEMENTE & ANSCHLÜSSE Geräteoberseite DEUTSCH T1. . . . . . . Pitch Bend – Taste T2. . . . . . Pitch Bend + Taste T3. . . . . . Shift-Taste T4. . . . . . Autoloop (Funktion) Taste (Shift: Loop In) T5. . . . . . Loop Length -/+ (Loop-Länge) (Shift: Beat Move > nur Traktor Pro) T6. . . . . . Gain-Regler T7. . . . . . Pitchfader inkl. Status LED Anzeige (leuchtet bei 0%) T8. . . . . . Reloop-Taste (Shift: Loop Out) T9. . . . . . FX Select-Taste (Shift: Master Deck-Zuweisung) T10. . . . . .
2. INBETRIEBNAHME - Schalten Sie das Gerät zunächst über den Ein/Aus-Schalter -B41- auf der Rückseite aus. - Verbinden Sie das beiliegende Netzteil mit der DC-Buchse -B40- des Gerätes. Stecken Sie nun den Netzadapter in eine freie Steckdose. - Verbinden Sie anschließend das mitgelieferte USB-Kabel mit dem Anschluss -B42- auf der Rückseite des Gerätes und einer freien USB-Schnittstelle an Ihrem Computer. 3.
Im Setup Wizard wählen Sie folgende Punkte aus: 1. D ie erste Frage „Are you using a USB/FireWire controller?“ beantworten Sie mit „Yes“. Anschließend klicken Sie auf „Next“. 2. I m Bereich „Choose your manufacturer:“ wählen Sie den Eintrag „Reloop“. Die anschließende Auswahlmöglichkeit „Choose your model:“ beantworten Sie mit „Mixage“. Wiederum bestätigen Sie die Auswahl mit „Next“. DEUTSCH 3.
3.2 MAPPING IMPORT [NUR TRAKTOR PRO] Damit Traktor die MIDI-Befehle, die Mixage sendet, den richtigen Funktionen zuordnen kann, ist eine Befehlszuweisungstabelle, auch Mapping genannt, nötig. Eine passende Mapping-Datei finden Sie auf der Installations-CD im Ordner „Mappings/Traktor Pro“. HINWEIS! Stets aktualisierte und erweiterte Mappings finden Sie auch online. Surfen Sie dazu auf http:// www.reloopdj.com/forum und öffnen Sie die Kategorie „Mapping Files“ im Bereich „Downloads for all Reloop products“.
Im Auswahlfenster öffnen Sie die Mapping-Datei, die sich auf der CD befindet oder gerade von der Reloop-Supportseite heruntergeladen wurde. Problembehebung Zur Behebung des Problems wie folgt vorgehen: 1. Öffnen Sie in Traktor den Einstellungsdialog, indem Sie auf das kleine Zahnrad am oberen, rechten Rand klicken. 2. Öffnen Sie die Kategorie „Controller Manager“. 3.
DEUTSCH 10 Element Funktion Funktion bei aktivem Shift -T3- T4 Autoloop (Funktion) Taste Setzt einen automatischen Loop mit der eingestellten Loop-Länge (-T15-), ohne dass der Loop-Endpunkt manuell bestimmt werden muss. Loop In / Set Cue Taste Setzt manuell den Anfangspunkt eines Loops. Gleichzeitig wird auch ein Cue-Punkt definiert. T5 Loop Length -/+ (Loop-Länge) Regler Drehen des Encoders variiert die Länge eines gesetzten Loops. Drücken des Encoders aktiviert bzw.
Element Funktion Funktion bei aktivem Shift -T3- T19 Play/Pause Taste Startet bzw. pausiert die Wiedergabe des Tracks. Cue 4 Taste Setzt und triggert den 4. CuePunkt. T20 TRAX-Encoder (Tracklist-Navigation) TRAX-Encoder (Ordner-Navigation) - D urch Drehen des Encoders lässt sich im Trackverzeichnis scrollen. -D urch Drücken des Encoders maximiert sich die Browser Ansicht. - Durch Drehen des Encoders lässt sich im Ordnerverzeichnis navigieren.
5.1 MIDI-CHANNEL-ZUWEISUNG ACHTUNG! Standardmäßig ist Mixage auf MIDI-Kanäle 1 oder 2 konfiguriert, der MIDI-Kanal kann dabei über den rückseitigen Schalter -B43- gewählt werden. Ein weiterer Mixage Controller kann - z.B. für DJ Teams – angeschlossen werden. Wichtig dabei ist, dass ein Mixage auf MIDI-Kanal 1 steht und der zweite Mixage auf MIDI-Kanal 2 (siehe Schalter -B43-). Die offiziellen Mappings seitens Reloop sind auf die standardmäßige Konfiguration ausgelegt.
5. Starten Sie nun das Firmware-Update-Tool von der Installations-CD und öffen die für Ihr Gerät passende Firmware-Datei. DEUTSCH 6. Führen Sie nun das Firmware-Update durch, indem Sie auf die Schaltfläche „Start“ klicken. 7. Die neue Firmware wird nun an das Gerät übertragen. 8. Ist das Update erfolgreich verlaufen, leuchten alle LEDs des Controllers. 9. Nachdem das Update erfolgreich abgeschlossen ist, beenden Sie das Firmware-Update-Tool und starten Mixage über den Ein/Aus-Schalter -B41- neu. 10.
Auch werden für Traktor (Pro) Nachfolgeversionen und andere DJ-Softwares stets aktualisierte Mappings bereitgestellt, damit Sie Reloop Mixage auch in Zukunft verwenden können. Ebenfalls können speziell auch für abweichende Setups spezielle Mappings erworben werden, die z.T. von der Nutzergemeinde stammen. Schauen Sie daher regelmäßig auf folgender Internetseite: www.reloopdj.com/forum Neben zahlreichen Downloads steht Ihnen hier auch ein Support zur Verfügung. 7. ANHANG 7.
Type MIDI MIDI 2 (Shift) CD1 LOW VR 37 76 CD1 CH FADER VR 38 77 CD2 GAIN VR 39 78 CD2 FILTER VR/CENTER 3A/3A 79/79 CD2 HIGH VR 3B 7A CD2 MID VR 3C 7B CD2 LOW VR 3D 7C CD2 CH FADER VR 3E 7D CUEMIX VR/CENTER 32/32 -- CH1 Only CROSSFADER VR 31 -- CH1 Only MASTER VR 30 -- CH1 Only PHONES VR 2F -- CH1 Only CD1 - SW/LED 01/01 40/01 CD1 + SW/LED 02/02 41/02 CD1 Search SW/LED 03/03 42/03 CD1 Scratch SW/LED 04/04 43/04 CD1 LOOP SW/LED 05/05 44
CC-ABSOLUTE (VR) Control Change messages are sent with status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number. The value from 0x00 to 0x7F, directly related to the location of the controller. CC-RELATIVE (ENC) Control Change messages are status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number.
7.3TIPPS ZUR FEHLERBEHEBUNG Sollten Probleme bei der Benutzung von Reloop Mixage auftreten, so ist dies Ihre erste Anlaufstelle, um diese zu beheben: Symptome Mögliche Ursachen Korrekturmaßnahmen Überprüfen Sie, ob das USB-Kabel richtig mit einem USB-Port Ihres Computers und Mixages USB-Port -B42- verbunden ist. Bitte prüfen Sie ebenfalls, ob das Steckernetzteil korrekt an dem Netzanschluss -B40- angeschlossen ist. Die LEDs des Controllers leuchten nur schwach auf und das Gerät reagiert nicht.
DEUTSCH
INSTRUCTION MANUAL CAUTION! For your own safety, please read this operation manual carefully before initial operation! All persons involved in the installation, setting-up, operation, maintenance and service of this device must be appropriately qualified and observe this operation manual in detail. This product complies with the requirements of the applicable European and national regulations. Conformity has been proven. The respective statements and documents are deposited at the manufacturer.
ENGLISH - The inside of the device does not contain any parts which require maintenance, with the exception of wear parts that can be exchanged from the outside. Only qualified staff must carry out maintenance, otherwise warranty does not apply! - The Fuse must exclusively be exchanged against fuses of the same class, with the same trigger features and nominal current rating. - Make sure that the power will only be supplied after the device has been fully set up. Always plug in the mains plug last.
MAINTENANCE - Check the technical safety of the device regularly for damage to the mains cord or the casing, as well as for wearout of wear parts such as rotary knobs and sliding faders. - If it is to be assumed that a safe operation is no longer feasible then the device must be disconnected and secured against accidental use.
1.1 CONTROL ELEMENTS & CONNECTIONS ENGLISH Surface T1. . . . . . . Pitch Bend – Button T2. . . . . . Pitch Bend + Button T3. . . . . . Shift Button T4. . . . . . Autoloop Button (Shift: Loop In) T5. . . . . . Loop Length -/+ (Shift: Beat Move > only Traktor Pro) T6. . . . . . Gain Dial T7. . . . . . Pitchfader incl. Status LED Indicator (illuminated at 0%) T8. . . . . . Reloop Button (Shift: Loop Out) T9. . . . . . FX Select Button (Shift: Master Deck Assignment) T10. . . . .
2. INITIAL OPERATION - First make sure to turn off the device via the On/Off Button -B41- on the rear panel. - Connect the included mains adapter to the device‘s DC jack -B40- and a shock-proof outlet. - Then connect the included USB cable to the corresponding connection -B42- on the device‘s rear panel and a free USB port of your computer. 3. COMPUTER CONFIGURATION Before you can use your new device a few basic computer adjustments have to be carried out.
In the setup wizard select the following items: 1. Answer the first question „Are you using a USB/FireWire Controller?“ with „Yes“. Then click on „Next“. ENGLISH 2. In the field „Choose your manufacturer“ select the item „Reloop“. The following menu item „Choose your model“ has to be answered with „Mixage“. Again confirm this selection with „Yes“. 3. The following question regarding connected hardware by manufacturer „Native Instruments“ has to be answered with „No“.
3.2 MAPPING IMPORT [ONLY TRAKTOR PRO] In order for Traktor to be able to assign the MIDI commands that Mixage sends to the correct functions, a special mapping is necessary. A suitable mapping can be found on the installation CD in the folder „Mappings/Traktor Pro“. NOTE! You can find updated and extended mappings online. Go to http://www.reloopdj.com/forum and open the category „Mapping files“ in the field „Downloads for all Reloop products“. Please proceed as follows in order to import the mapping: 1.
In the selection screen open the mapping file that is found on the CD or that was downloaded from the Reloop support site. ENGLISH Troubleshooting Should a problem arise and Mixage´s LEDs are not lit correctly, this is probably caused in most cases by installed MIDI software (e.g. MidiYoke, Maple Virtual MIDI Cable, Bome, Osculator, etc.) In order to solve the problem proceed as follows: 1. In Traktor open the adjustment dialogue by clicking the small cog wheel in the upper right corner. 2.
Function Function with activated Shift -T3- T4 Autoloop Button Sets an automatic loop with the set loop length (-T15-), without the necessity of setting the loop ending point manually. Loop In / Set Cue Button Manually sets the starting point of a loop. Simultaneously a cue point will be defined. T5 Loop Length -/+ Dial By turning the encoder the set loop‘s length can be varied. By pressing the encoder the loop active function can be activated and deactivated respectively.
ENGLISH Element Function Function with activated Shift -T3- T19 Play/Pause Button Starts and pauses the track‘s playback respectively. Cue 4 Button Sets and triggers the 4th cue point. T20 TRAX Encoder (Tracklist Navigation) TRAX Encoder (Folder Navigation) -B y turning the encoder it is possible to scroll through the track list. -B y pressing the encoder browser view will be maximized. - By turning the encoder it is possible to navigate through the folders.
5.1 MIDI ASSIGNMENT NOTE! By default Mixage is configured for MIDI channels 1 or 2. The MIDI channell can be selected via the switch on the rear side -B43-. It is possible to connect a further Mixage controller, i.e. for DJ teams. For this purpose it is important that one Mixage is on MIDI channel 1 and the second Mixage is on MIDI channel 2 (see switch -B43-). Reloop‘s official mappings are laid-out according to the standard configuration. Therefore changes are usually unnecessary.
ENGLISH 5. Now start the firmware update tool from the installation CD and open the firmware file that suits your device. 6. Carry out the firmware update by clicking the „Start“ button. 7. The new firmware will now be transmitted to the device. 8. After a successful update all LEDs of the controller will be lit. 9. After the update has been completed successfully please end the firmware update tool and reboot Mixage via the On/Off Button -B4110.
In order to be able to utilize Reloop Mixage in the future, updated mappings are offered for Traktor (Pro) follow-up versions and other softwares. Additionally it is possible to purchase special mappings for differing setups, that derive from the user community. Therefore regularly check the following website: www.reloopdj.com/forum Besides numerous downloads you can also find a support forum. 7. APPENDIX 7.
ENGLISH SW name Type MIDI MIDI 2 (Shift) CD1 LOW VR 37 76 CD1 CH FADER VR 38 77 CD2 GAIN VR 39 78 CD2 FILTER VR/CENTER 3A/3A 79/79 CD2 HIGH VR 3B 7A CD2 MID VR 3C 7B CD2 LOW VR 3D 7C CD2 CH FADER VR 3E 7D CUEMIX VR/CENTER 32/32 -- CH1 Only CROSSFADER VR 31 -- CH1 Only MASTER VR 30 -- CH1 Only PHONES VR 2F -- CH1 Only CD1 - SW/LED 01/01 40/01 CD1 + SW/LED 02/02 41/02 CD1 Search SW/LED 03/03 42/03 CD1 Scratch SW/LED 04/04 43/04 CD1 LOOP
CC-ABSOLUTE (VR) Control Change messages are sent with status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number. The value from 0x00 to 0x7F, directly related to the location of the controller. CC-RELATIVE (ENC) Control Change messages are status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number.
7.3 TROUBLESHOOTING If any problem should arise while using Reloop Mixage the following chart is the first drop-in center: Symptoms Possible Causes Corrective Measures The device does not receive any power when turning it on via the ON/ OFF Button -B41-. USB cord or mains adapter are not connected correctly. Check whether the USB cord is connected correctly to a free USB port of your computer and Mixage‘s USB port -B42-.
ENGLISH 35
MODE D‘EMPLOI ATTENTION! Pour votre propre sécurité, veuillez lire attentivement ce mode d‘emploi avant la première utilisation ! Toutes les personnes chargées de l’installation, de la mise en service, de l’utilisation, de l’entretien et la maintenance de cet appareil doivent posséder les qualifications nécessaires et respecter les instructions de ce mode d‘emploi.
ENTRETIEN - Contrôlez régulièrement le bon état de l’appareil (boîtier, cordon) et l’usure éventuelle des molettes et curseurs. - Si vous supposez que l’appareil ne peut plus être utilisé en toute sécurité, mettez l’appareil horsservice et assurez-le contre toute réutilisation involontaire.
1.1 ÉLÉMENTS DE COMMANDE & CONNECTIQUE FRANÇAIS Face supérieure de l‘appareil T1. . . . . . . Touche Pitch Bend T2. . . . . . . Touche Pitch Bend + T3. . . . . . . Touche Maj T4. . . . . . . Autoloop (fonction) touche (Maj : Loop In) T5. . . . . . . Loop Length -/+ (longueur de boucle) (Maj : Beat Move > uniquement Traktor Pro) T6. . . . . . . Régleur de gain T7. . . . . . . Pitchfader avec DEL d‘affichage d‘état (s‘allume à 0 %) T8. . . . . . . Touche Reloop (Maj : Loop Out) T9. . . . . . .
1.1 ÉLÉMENTS DE COMMANDE & CONNECTIQUE FRANÇAIS Face supérieure de l‘appareil T1. . . . . . . Touche Pitch Bend T2. . . . . . . Touche Pitch Bend + T3. . . . . . . Touche Maj T4. . . . . . . Autoloop (fonction) touche (Maj : Loop In) T5. . . . . . . Loop Length -/+ (longueur de boucle) (Maj : Beat Move > uniquement Traktor Pro) T6. . . . . . . Régleur de gain T7. . . . . . . Pitchfader avec DEL d‘affichage d‘état (s‘allume à 0 %) T8. . . . . . . Touche Reloop (Maj : Loop Out) T9. . . . . . .
2. MISE EN SERVICE - Commencer par éteindre l‘appareil avec l‘interrupteur marche/arrêt -B36- situé sur la face arrière. - Brancher le cordon secteur fourni dans la prise DC -B38- de l‘appareil. Brancher à présent l‘adaptateur secteur dans une prise de courant libre. - Raccorder ensuite le câble USB fourni au port -B40- situé sur la face arrière de l‘appareil et à un port USB libre de votre ordinateur. 3.
Sélectionner les points suivants dans le Setup Wizard : FRANÇAIS 1.Répondre à la première question : „Are you using a USB/FireWire controller?“ par „Yes“. Cliquer ensuite sur „Next“. 2.Dans la rubrique „Choose your manufacturer:“, sélectionner l‘entrée „Reloop“. Pour la sélection suivante : „Choose your model:“, choisir „Mixage“. Valider de nouveau la sélection avec „Next“. 3.Par défaut, répondre aux questions suivantes concernant le matériel connecté du fabricant „Native Instruments“ par „No“.
3.2 IMPORTATION DE MAPPAGE [SEULEMENT TRAKTOR PRO] La table d‘affectation des commandes, dénommée mappage, est nécessaire pour que le logiciel Traktor affecte correctement les commandes MIDI envoyées par la console Mixage aux fonctions respectives. Le fichier de mappage adéquat se trouve sur le cédérom d‘installation dans le répertoire „Mappings/ Traktor Pro“. NOTE! Vous trouverez également les mappages actuels et améliorés sur notre site http://www.reloopdj.
Dans la fenêtre de sélection, ouvrir le fichier de mappage situé sur le cédérom ou téléchargé du site Reloop. FRANÇAIS Dépannage Si un problème survient et que les DEL de la console Mixage ne s‘allument pas correctement, la panne vient généralement du logiciel MIDI installé (par ex. MidiYoke, Maple Virtual MIDI cable, Osculator etc.). Procéder comme suit pour le dépannage : 1.Ouvrir le dialogue de réglage dans Traktor en cliquant sur la petite roue dentée le côté droit de la fenêtre. 2.
Fonction Fonction avec touche Maj -T3- enfoncée T4 Touche Autoloop (fonction) Règle une boucle automatique avec la longueur de boucle paramétrée (-T15-), sans devoir définir manuellement le point final de la boucle. Touche Loop In/Set Cue Règle manuellement le point initial d‘une boucle. En même temps, un point Cue est défini. T5 Régleur Loop Length -/+ (longueur de boucle) Tourner l‘Encoder pour varier la longueur d‘une boucle définie.
FRANÇAIS Élément Fonction Fonction avec touche Maj -T3- enfoncée T19 Touche Play/Pause Lance ou pause la lecture de la piste. Touche Cue 4 Défini et déclenche le 4ème point Cue. T20 TRAX-Encoder (navigation dans la liste des pistes) TRAX-Encoder (navigation dans les dossiers) -T ourner l‘Encoder pour dérouler le répertoire des pistes. -E nfoncer l‘Encoder pour maximiser la vue Browser. - Tourner l‘Encoder pour naviguer dans le répertoire de dossiers.
5.1 AFFECTATION DES CANAUX MIDI ATTENTION ! Par défaut, votre Mixage est configurée sur les canaux MIDI 1 ou 2, le canal MIDI peut être sélectionné avec le sélecteur -B43- sur la face arrière. Il est possible de connecter une autre console Mixage, par ex. pour des équipes de DJ. Il est alors essentiel qu‘une console Mixage soit sur le canal MIDI 1 et l‘autre sur le canal MIDI 2 (voir sélecteur -B43-). Les mappages officiels fournis par Reloop sont conçus pour la configuration par défaut.
FRANÇAIS 5. Lancer à présent l‘outil de mise à jour du micrologiciel depuis le cédérom d‘installation et ouvrir le fichier de micrologiciel correspondant pour votre appareil. 6.Exécuter la mise à jour du micrologiciel en cliquant sur le bouton „Start“. 7.Le nouveau micrologiciel est alors transmis à l‘appareil. 8.Lorsque la mise à jour est correctement achevée, toutes lesl DEL clignotent simultanément. 9.
De même, notre site met à disposition les dernières versions des mappages pour les versions ultérieures de Traktor Pro et d‘autres logiciels pour DJ afin tenir à jour votre Reloop Mixage. Vous pouvez aussi acheter des mappages spéciaux provenant en partie de la communauté d‘utilisateurs pour des configurations diverses. Consultez donc régulièrement le site: www.reloopdj.com/forum Outre les nombreux téléchargements, une assistance technique est aussi disponible. 7. ANNEXE 7.
FRANÇAIS SW name Type MIDI MIDI 2 (Shift) CD1 LOW VR 37 76 CD1 CH FADER VR 38 77 CD2 GAIN VR 39 78 CD2 FILTER VR/CENTER 3A/3A 79/79 CD2 HIGH VR 3B 7A CD2 MID VR 3C 7B CD2 LOW VR 3D 7C CD2 CH FADER VR 3E 7D CUEMIX VR/CENTER 32/32 -- CH1 Only CROSSFADER VR 31 -- CH1 Only MASTER VR 30 -- CH1 Only PHONES VR 2F -- CH1 Only CD1 - SW/LED 01/01 40/01 CD1 + SW/LED 02/02 41/02 CD1 Search SW/LED 03/03 42/03 CD1 Scratch SW/LED 04/04 43/04 CD1 LOOP
CC-ABSOLUTE (VR) Control Change messages are sent with status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number. The value from 0x00 to 0x7F, directly related to the location of the controller. CC-RELATIVE (ENC) Control Change messages are status 0xBn, where n is the channel, for the specified CC controller. Thus the controller MIDI ID is indicated with the channel along with the CC number.
7.3 CONSEILS DE DÉPANNAGE Si vous avez des problèmes lors de l‘utilisation de votre Reloop Mixage, consultez cette ressource en premier recours pour dépanner : Symptôme Causes possibles Dépannage L‘appareil ne se met pas sous tension lorsque vous appuyez sur l‘interrupteur MARCHE/ARRÊT -B41-. Branchement incorrect du câble USB ou de la fiche secteur. Vérifier le branchement correct du câble USB sur un port USB de votre ordinateur et sur le port USB -B42- de votre Mixage.
FRANÇAIS 51
WWW.RELOOPDJ.COM Reloop Trademark Global Distribution GmbH Schuckertstr. 28 48153 Muenster / Germany © Copyright 2009 Nachdruck Verboten! Unbenannt-3 1 19.05.