User's Manual

User Manual
version 3.2
Move series radiocontrols
mod.
GENESIS, PAIL, BRICK
and
T
April 2016
REM
device
®
- ITALY 7
Switching on, Activation, Use, Automatic shutdown
Switching on
If not otherwise stated in the datasheet, the mushroom EMERGENCY STOP
BUTTON is used to switch the transmitter on and off. To switch on,
rotate and disconnect the mushroom EMERGENCY STOP BUTTON
Check that the GREEN LED (ON) flashes (just once), indicating that the unit
is switched on (see Figure 1, corresponding model).
Activation
Press the START BUTTON or activate the START LEVER or turn the key to
START, depending on the model. The GREEN LED (ON) flashes quickly to
indicate that the unit has been activated.
If, on the other hand, the transmitter bleeps and the RED LED (BATT) comes
on, check no controls are on via the other buttons or actuators that
prevent activation. At the same time, the audible warning of the operating
machine can be heard (if any).
Use
Press the relevant buttons or operate the relevant control actuators for the
operation you want to perform, paying attention to how the machine
behaves.
If you experience any kind of trouble controlling the machine
(for mechanical or electrical reasons or if it is not performing
as you intended in any way), press the EMERGENCY STOP
BUTTON straight away.
Never leave the transmitter unit unattended when it is switched on, even
for just a few seconds. Always switch off the transmitter unit at the end.
Put the transmitter unit away in a safe place where it cannot be reached by
unauthorized personnel; never allow inexperienced personnel to use the
transmitter unit.
Automatic shutdown
If this function is enabled (default factory setting), the transmitter unit will
switch off automatically after approx. 4 minutes of inactivity.
To restart the unit, press the START actuator.
LAYOUT and DESCRIPTION of CONTROLS
The various models differ in terms of the number of controls available and
how they are arranged. A different appendix is associated with each
configuration (see page 27) and is an integral part of this manual.
User Manual
version 3.2
Move series radiocontrols
mod.
GENESIS, PAIL, BRICK
and
T
April 2016
8
REM
device
®
- ITALY
Note: on the GENESIS, PAIL, BRICK and T transmitters, the symbols of the
respective controls are featured on the plates on the product and/or
provided with the unit. If labels or plates other than the ones provided are
used, the symbols must match the machine's functions and movements
exactly and must comply with current regulations.
SERVICE FUNCTIONS
Electronic key
It is possible to prevent unauthorized staff to use the transmitter via the
function:
LOCKING and UNLOCKING the transmitter unit
In page I of the appendix (see page 27 of this manual) the actuators
assigned to this function are shown.
To lock the use of the transmitter, identify actuator Sp3 (or U1)
as specified in the appendix and follow the following
instructions:
a) power up the transmitter using the mushroom EMERGENCY STOP
BUTTON (or using the key selector, where applicable);
b) operate Sp3 (or U1) and operate the START at the same time;
keep on and count 5 beeps and flashes of the F1 LED (if applicable);
after exactly 5 beeps and flashes, release the START and Sp3 (or U1);
c) the GREEN LED (ON) will produce a long flash accompanied by a beep to
confirm that the procedure has been performed correctly.
If the procedure is not performed in this exact sequence or the controls are
held any longer, the operation will be aborted and you will need to repeat
the sequence from the beginning.
If you attempt to activate the transmitter following this operation, the
indicator lights (LEDs) will flash in turn and the transmitter unit's audible
alarm will sound (ring).
To unlock the transmitter, repeat the sequence.
If the transmitter is locked out, you will hear a long ring; if the
transmitter is unlocked, it will play a short melody.
On models with a display, the count will come up on the
display.