KEROSENE FORCED AIR HEATER User’s Manual & Operating Instructions MODEL NUMBERS: REM-45-KFA-O / REM-80T-KFA-O / REM-140T-KFA-O / REM-190T-KFA-O / REM-215T-KFA-O CONSUMER: READ AND SAVE THESE INSTRUCTIONS Locating Your Serial Number: Your serial number can be found on a white label on the right side cover of your heater. For Example: 150812779. Have your Serial Number ready before calling customer service at 866-676-1989.
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE TABLE OF CONTENTS Safety Information............................................2-3 What’s in the Box................................................4 Specifications......................................................5 Features.............................................................5 Assembly Instructions.........................................5 Opeation...........................................................
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE SAFETY INFORMATION (CONT.) WARNING WARNING RISK OF INDOOR AIR POLLUTION! The products described in this manual are kerosene direct-fired, forced air heaters. Kerosene forced air heaters are primarily intended for use for temporary heating of buildings under construction, alteration or repair. Direct-fired means that all of the combustion products of the heater enter the heated space.
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE WHAT’S IN THE BOX (45-KFA / 80T-KFA) Cord Wraps (Optional) Carry Handle (1) Shown With Optional Cord Wraps 10 mm Screws (2) Heater (1) 15 mm Screws (2) WHAT’S IN THE BOX (140T-KFA / 175T-KFA / 215T-KFA) Tip: Be sure to remove the axle from the side of the Styrofoam packaging.
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE SPECIFICATIONS Model # 45-KFA 80T-KFA 140T-KFA 190T-KFA 215T-KFA 45,000 80,000 140,000 190,000 215,000 Fuel Consumption: Gal/Hr 0.35 0.63/2.38 1.1/4.16 1.42 1.63 Fuel Tank Capacity: Gallons 5 5 10 13 13 3.0 3.8 6.6 8.5 9.0 Rating: Btu/Hr Pump Pressure: psi Volts: AC/Hz 120VAC / 60Hz 120VAC / 60Hz 120VAC / 60Hz 120VAC / 60Hz 120VAC / 60Hz Amps Phase 1.4 1.5 2.4 2.7 2.
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE OPERATION Fueling The Heater: NOTE: Kerosene should only be stored in a blue container that is clearly marked “Kerosene.” Never store kerosene in a red container. Red is associated with gasoline. Kerosene (K-1) For optimal performance of this heater, it is strongly suggested that K-1 kerosene be used, especially in temperatures lower than 26°F (-3°C).
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE OPERATION (CONT.) Stopping / Restarting Heater: - To stop the heater, move the power switch to the “Off” position and unplug the power cord. - To restart the heater; wait 10 seconds and follow ignition steps. Starting the Heater: (Ignition) 1. Fill the tank with kerosene or other approved fuel until needle on fuel gauge points to “F”. 2. Replace fuel cap and tighten firmly. 3.
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE Service: DO NOT TAMPER WITH THE UNIT. HAVE A COMPETENT SERVICEMAN MAKE ANY NECESSARY ADJUSTMENT OR REPAIRS. MAINTENANCE ROTOR: The rotor with carbon vanes should be evaluated every heating season. The rotor is behind the air filters. The vanes should be inspected for damage or wear. The rotor should be inspected for damage, chips, wear, cracks. Use only original equipment parts.
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE MAINTENANCE (CONT.) Service (Continued): PUMP PRESSURE: While heater is operating, turn adjusting screw clockwise to increase, counter-clockwise to decrease pressure. Correct pump pressure is as follows: SPARK PLUG: Clean and re-gap every 600 hours of operation, or replace as needed. After removing the spark plug, clean the terminals with a wire brush. Re-gap the terminals to 0.140” (3.5mm). See Figure 4.
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE WIRING DIAGRAMS 45-KFA 80T - 215T-KFA 80T-KFA 140T-KFA / 175T-KFA / 190T-KFA (80T-KFA) (140T-KFA) (175T-KFA / 190T-KFA / 215T-KFA) Models 140T/175T/190T/215T-KFA have a digital display. © 2018 Pinnacle Climate Technologies, Inc.
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE TROUBLESHOOTING GUIDE Problem Heater Ignites, but main PCB shuts off after a short period of time. Lamp flickers and LED display shows “E1”. Heater will not operate or motor runs for a short time. Lamp flickers and LED display shows “E1”. Possible Cause 1. 2. 3. 4. 5. 6. 7. 8. Solution Incorrect pump pressure. Dirty input, output or lint filter. Dirty fuel filter. Nozzle is dirty. Photocell lens is dirty.
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE EXPLODED VIEW 33** 32* 34** 13 11 10 14 12 40** 8 9 29 15 3 24 25 31 30 26 5 2 4 27 6 7 35** 1** 23 37** 19 16 41 28 21 17 18 20 22 30 36** 43** * 45-KFA - 80T-KFA Only ** 140T-KFA - 215T-KFA Only 38** 42** © 2018 Pinnacle Climate Technologies, Inc.
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE PARTS LIST # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Description Drain Bolt Fuel Gauge Fuel Filter Fuel Cap - Large Plastic Power Cord Power Switch Thermostat Control Knob Air Line Thermostat Limit Control Photocell Bracket Fuel Line Photocell Burner Head Assembly Nozzle Kit Spark Plug Kit Motor Pump Body Rotor Kit End Pump Cover Filter Kit End
NEVER LEAVE HEATER UNATTENDED WHILE BURNING OR WHILE CONNECTED TO A POWER SOURCE LIMITED WARRANTY Pinnacle Climate Technologies, Inc. warrants this heater to the original retail purchaser only, to be free from defects in material and workmanship for a period of one (1) year from the date of initial purchase. This product must be properly installed, maintained and operated in accordance with the instructions provided. If Pinnacle Climate Technologies, Inc.
CALENTADOR DE AIRE FORZADO DE QUEROSENO Manual del usuario e instrucciones de operación MODELOS N.° REM-45-KFA-O / REM-80T-KFA-O / REM-140T-KFA-O / REM-190T-KFA-O / REM-215T-KFA-O CONSUMIDOR: LEA Y CONSERVE ESTAS INSTRUCCIONES Cómo localizar su número de serie: El número de serie lo puede encontrar en una etiqueta blanca en el lado derecho de la cubierta de su calentador. Por ejemplo: 150812779. Tenga su número de serie a la mano antes de llamar al servicio al cliente al 866-676-1989.
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN ÍNDICE Información de seguridad....................................... 2-3 Qué hay en la caja...................................................... 4 Especificaciones......................................................... 5 Características............................................................ 5 Instrucciones de armado............................................ 5 Funcionamiento.......
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN INFORMACIÓN DE SEGURIDAD (CONTINÚA) ¡RIESGO DE DESCARGA ELÉCTRICA! ¡RIESGO DE CONTAMINACIÓN DEL AIRE INTERIOR! SIEMPRE utilice la energía eléctrica (voltaje y frecuencia) que se indica en la placa de modelo del calentador. SIEMPRE use solamente tomacorrientes con conexión a tierra y cable de extensión de tres puntas.
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN QUÉ HAY EN LA CAJA (45-KFA / 80T-KFA) Enrolladores de cable (Opcional) Asa (1) Ilustrado con enrolladores de cable opcionales Tornillos de 10 mm (2) Calentador (1) Tornillos de 15 mm (2) QUÉ HAY EN LA CAJA (140T-KFA / 175T-KFA / 215T-KFA) Consejo: Asegúrese de retirar el eje del lateral del empaque de espuma de poliestireno.
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN ESPECIFICACIONES N.° de modelo 45-KFA 80T-KFA 140T-KFA 190T-KFA 215T-KFA 45,000 80,000 140,000 190,000 215,000 0.35 0.63/2.38 1.1/4.16 1.42 1.63 5 5 10 13 13 3.0 3.8 6.6 8.5 9.
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN Llenar de combustible el calentador: FUNCIONAMIENTO - NUNCA utilice queroseno que haya estado almacenado de una temporada a la siguiente. El queroseno se deteriora con el tiempo. EL QUEROSENO VIEJO NO SE QUEMARÁ ADECUADAMENTE EN ESTE CALENTADOR. NOTA: El queroseno debe almacenarse únicamente en un contenedor azul que esté claramente identificado con la palabra “queroseno”.
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN FUNCIONAMIENTO (CONTINÚA) - Entre 0 °F (-18º C) y 99 °F (37 ºC) la pantalla mostrará la temperatura real. Apagado / Reencendido del calentador: - Para apagar el calentador, mueva el interruptor a la posición OFF (apagado) y desenchufe el cable eléctrico. - Para reencender el calentador, espere 10 segundos y siga los pasos de ignición. Encendido del calentador: (Ignición) 1.
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN MANTENIMIENTO el extremo de plástico colocado debajo del soporte del motor/motor y alejado del aspa del ventilador. Servicio: NO ALTERE LA UNIDAD. PIDA A UN TÉCNICO COMPETENTE QUE HAGA LAS REPARACIONES O AJUSTES NECESARIOS. ROTOR: Evalúe el estado del rotor con álabes de carbono cada temporada de calefacción. El rotor está detrás de los filtros de aire.
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN MANTENIMIENTO (CONT.) Servicio (Continuación): PRESIÓN DE LA BOMBA: Mientras el calentador está funcionando, gire la válvula de seguridad hacia la derecha para aumentar la presión o hacia la izquierda para disminuirla.
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN DIAGRAMAS ELÉCTRICOS 45-KFA PCI DE CONTROL ROJO ROJO NEGRO ENCENDEDOR BUJÍA NEGRO LUZ (LED) VENTILADOR 1 NARANJA VENTILADOR 2 ROSA NEGRO MOTOR DE LA BLANCO BOMBA VERDE TIERRA NEGRO FOTOCÉLULA: BLANCO NEGRO INTERRUPTOR DE ENCENDIDO ENCHUFE DE ALIMENTACIÓN CONTROL DE LÍMITE FUSIBLE 8A/125AVC NEGRO NEGRO CA 120V 60 HZ BLANCO AMARILLO VERDE TIERRA BLANCO 80T - 215T-KFA PCI D
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN GUÍA PARA LA SOLUCIÓN DE PROBLEMAS Problema Posible causa Solución El calentador se enciende, pero la placa de circuitos impresos principal se apaga después de poco tiempo. La lámpara parpadea y la pantalla LED muestra “E1”. 1. Presión de la bomba incorrecta. 2. Filtro de entrada, de salida o de pelusas sucio. 3. Filtro de combustible sucio. 4. Boquilla sucia. 5.
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN VISTA DETALLADA 33** 32* 34** 13 11 10 14 12 40** 8 9 29 15 3 24 25 31 26 5 2 4 27 6 7 28 35** 1** 23 37** 19 16 41 30 21 17 18 20 22 30 36** 43** * Sólo 45-KFA - 80T-KFA ** Sólo 140T-KFA - 215T-KFA © 2018 Pinnacle Climate Technologies, Inc.
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN LISTA DE PIEZAS # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 Descripción Perno de drenaje Indicador de combustible Filtro de combustible Tapa del tanque de combustible plástico, grande Cable eléctrico Interruptor de encendido Perilla de control del termostato Tubo de aire Control de límite del termostato Soporte d
NUNCA DEJE DESATENDIDO EL CALENTADOR MIENTRAS ESTÉ ENCENDIDO O MIENTRAS ESTÉ CONECTADO A UNA FUENTE DE ALIMENTACIÓN GARANTÍA LIMITADA Pinnacle Climate Technologies, Inc. garantiza este calentador únicamente al comprador minorista original, como libre de defectos en materiales y mano de obra por un periodo de un (1) año a partir de la fecha de la compra inicial. Este producto debe instalarse, mantenerse y usarse correctamente de acuerdo con las instrucciones suministradas.