Manual

CLEANING AND MAINTENANCE
NOTICE: Below are instructions
for servicing your chain saw. Any
servicing not mentioned below
should be done by an authorized
service center,
CLEANING SAW BODY
_1= WARNING: Remove battery
from chain saw before servicing.
Severe injury or death could oc-
cur from body contact with mov=
ing chain.
_lb WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
_, WARNING: When cleaning saw
body,
• do not submerge saw in
any liquids
• do not use products
that contain ammonia,
chlorine, or abrasives
• do not use chlorinated
cleaning solvents, carbon
tetrachloride, kerosene,
or gasoline
Normal Guide Bar Maintenance
1. Remove guide bar from chain saw.
2. Remove sawdust from guide bar
groove periodically. Use putty knife
or wire (see Figure 31 ).
3. Clean oil slots after each day of use.
4. Remove burrs from sides of guide
bar. Use flat file to make side edges
square.
Replace guide bar when
• bar is bent or cracked
• inside groove of bar is badly worn
Note: When replacing guide bar, see
Replacement Parts" and Accessories for
replacement in%rmafion.
/ Burr
FlatFile J'J
Guide Bar
Cleaning Groove With
f PuttyKnife
OilSlot
Figure 31 - Guide Bar Maintenance
Keep saw body clean. Use a soft cloth damp-
ened with a mild soap and water mixture.
Wipe saw body to clean.
CARE OF GUIDE BAR
Groove
/
Guide Bar
/ J
/
/
/
Normal Guide
Bar
Uneven bar wear causes most guide bar prob-
lems. Incorrect sharpening of chain cutter
and depth gauge settings often cause this.
When bar wears unevenly, it widens guide
bar groove (see Figure 30). This causes chain
clatter and rivet popping. Saw will not cut
straight. Replace guide bar if this occurs.
Inspect guide bar before sharpening chain.
A worn or damaged guide bar is unsafe. A
worn or damaged guide bar will damage
chain. It will also make cutting harder.
Guide Bar
\
Guide Bar With
Uneven Wear
Figure 30 - Guide Bar Cross Section
Showing Uneven Bar Wear
SHARPENING SAW CHAIN
_I, WARNING: Remove battery
from chain saw before servicing.
Severe injury or death could oc-
cur from body contact with mov=
ing chain.
WARNING: Cutting edges on
chain are sharp. Use protective
gloves when handling chain.
Keep chain sharp. Your saw will cut faster
and more safely. A dull chain will cause
undue sprocket, guide bar, chain, and motor
wear. If yon must force chain into wood and
cutting creates only sawdust with few large
chips, chain is dull.
items Needed to Sharpen Chain
Purchase these items from your local
dealer, hardware store, or chain saw sup-
plies outlet.
° 5/32" round file
• Depth gauge tool
• File guide
• Vise
• Medium sized flat file
Sharpening Cutters
Use file guide tk_r30° filing.
1. Adjust chain tier proper tension (see
Saw Chain Tension, page 11).
2. Clamp guide bar in vise to hold saw
steady. Note: Do not clamp chain.
3. Press 5/32" round file (attached to file
guide) into groove between top plate and
depth gauge on chain. File guide should
rest on both top plate and depth gauge
(see Figure 32). Note: File at midpoint
of guide bar.
..... _/_Filing Direction
....... File Guide
30 ° Guide Mark
/32" Round
File
Note:This illustration shows file guide placement
and filing direction for sharpening cutters on left
side of chain.
Figure 32 - File and File Guide Place-
ment on Chain
4. Hold file guide level. Make sure 30°
mark on file guide is parallel to cen-
ter of guide bar (see Figure 33). This
will insure that you file cutters at 30°
angle.
5. File from inside towards outside of
cutter until sharp. Only file in this one
direction (see Figure 33). Note: Two or
three strokes with file should sharpen
cutter.
6. After each cutter is sharpened, move
chain tk_rward to sharpen next cutter.
File all cutters on one side of chain.
7. Move to other side of chain and repeat
process.
Depth Gauge (left
side of chain) ,,
Groove ..
Top Plate (left ",_......
sideof chain)
Depth Gauge (right
side of chain)
Groove
\
TopPlate(right
sideofchain)
Right Sideof Chain
Figure 33 - Chain Part Locations
16