Professional Capture System Universal Infrared SystemCode Controller IR-PRO T3 T3 Operation Guide v1.
FEDERAL COMMUNICATIONS COMMISSION NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
T3 Universal System Controller BATTERY DISPOSAL Li-ion For environmental reasons, your T3 universal system controller uses “environmentally sound” Lithium-ion rechargeable batteries. These batteries do not contain any poisonous heavy metals that can damage the environment. In the interest of recycling, please do not dispose of these batteries in the household waste at the end of their useful life. Instead, dispose of them at an appropriate collection site. SAFETY SUGGESTIONS Read Instructions.
Servicing. Do not attempt any service beyond that described in the operating guide. Refer all other service needs to qualified service personnel. Damage Requiring Service. The unit should be serviced by qualified service personnel when: • • • The power supply cord or the plug has been damaged. Objects have fallen or liquid has been spilled into the unit. The unit does not appear to operate normally or exhibits a marked change in performance.
T3 Universal System Controller Remote Technologies Incorporated is not liable for any damages caused by its products or for its failure of its products to perform, including any lost profits, lost savings, incidental damages, or consequential damages. Remote Technologies Incorporated is not liable for damages based upon inconvenience, loss of use of the product, loss of time, interrupted operation, commercial loss, any claim made by a third party or made by you for a third party.
Contents Federal Communications Commission Notice ---------------------- i Battery Disposal ----------------------------------------------------------- ii Safety Suggestions -------------------------------------------------------- ii Limited Warranty -------------------------------------------------------- iii Disclaimer-------------------------------------------------------------------iv Contents------------------------------------------------------------------------ v Chapter 1.
T3 Universal System Controller Battery ------------------------------------------------------------------- 17 Sound -------------------------------------------------------------------- 18 Calibrate Touchscreen------------------------------------------------ 19 Programming The T3---------------------------------------------------- 20 Chapter 4.
Chapter 1. Welcome Thank you for purchasing the T3 universal system controller. The T3 combines the power and flexibility of a graphic LCD touchscreen with an ergonomic design that permits effortless onehanded operation. This design overcomes the need for a compromise between form and function. Sleek and perfectly balanced, the T3 is infinitely flexible and expandable. The T3 takes complete control of the home theater, replacing all other remotes.
T3 Universal System Controller UNPACKING AND INSPECTION After unpacking your new T3 universal system controller, save all of the packing materials in case you ever have to ship the unit. Thoroughly inspect the T3 and packing materials for signs of damage. Report any damage to the carrier immediately. Report any equipment malfunctions to Remote Technologies Incorporated or an authorized Remote Technologies Incorporated distributor.
Chapter 2. Introduction FEATURES The T3 provides superior quality and reliability as well as these specific features: A replacement for all of the remote controls in a home theater. The T3 can reproduce all of the commands of almost any other infrared remote control. A programmable graphic display. The T3 uses powerful Windows® based software that makes it easy to place buttons, text, graphics, symbols and icons anywhere on the display.
T3 Universal System Controller Both infrared (IR) and radio frequency (RF) output options. You can even use both options on the same unit. A built in motion sensor can automatically turn the unit on when it is picked up. A USB port for communication with the TheaterTouch Designer programming software. Non-volatile flash memory. The T3 will not lose any programmed data when the battery is removed. One-year parts and labor warranty Available only to system integration professionals.
Introduction Do not disassemble the unit. Service of the T3 should be performed by authorized personnel only. CLEANING Occasional cleaning may be required, depending on use. It is recommended that you create a “Clean” button somewhere on the Home page of the T3. This button should link to a page that does not contain commands or macros that could be inadvertently executed while cleaning the unit.
T3 Universal System Controller often. Since the T3 can safely be charged after each use, a docking station is included for convenience. If left out of the docking station, the T3 will remain in sleep mode for 1 – 2 months before shutting down. At that point the battery must be recharged. The T3 Docking Station can be placed on a flat surface such as a shelf or table, or it can be mounted to a wall using the mounting holes on the back of the unit.
Introduction GETTING STARTED Start by inserting the battery connector into the mating plug on the T3. Make sure the connector is oriented properly before attempting to insert it. Next, turn the unit on by sliding the power switch into the “ON” position (toward the battery). After power is applied, the T3 will take approximately ten seconds to load the operating system, the application software, and the user program. This long delay only occurs from a power-down state.
T3 Universal System Controller REMOTE REFERENCE Front Light Sensor Touchscreen Display Home Page Button Page Scroll Buttons 8 Keypad Buttons
Introduction Back IR Transmission Window Audio Speaker Lithium-ion Battery Pack USB Programming Port Power Switch Docking Station Contacts 9
T3 Universal System Controller DOCKING STATION REFERENCE Front Charge Contacts Charge LED Back Wall Mount Holes 10 1-3/8 in.
Chapter 3. Operation THE TOUCHSCREEN DISPLAY The T3 touchscreen display is organized into a series of pages. Normally each page contains objects (buttons, text, graphics, etc.) that are related in some way. For instance, they may all display information necessary for controlling a particular DVD player. By default, the T3 has one Home page—all other pages are normally accessed from links on the Home page. In addition, any page can contain buttons with a link to any other page.
T3 Universal System Controller THE CONTROL PANEL PAGE The Control Panel page can be displayed by first setting the T3 power switch to the off position, and then pressing and holding the Home button while sliding the power switch to the on position. You can also access the Control Panel page by assigning a “Control Panel” page link to a button using the TheaterTouch Designer software.
Operation BACKLIGHT LEVEL This button displays a window that allows you to adjust the backlight brightness and enable/disable the Ambient Light Sensor. If the light sensor is disabled, there is only one backlight level to adjust. Press the left arrow or right arrow buttons to adjust. Press the OK button when finished. With the light sensor disabled, the backlight brightness will always stay at the same level whenever the T3 is turned-on.
T3 Universal System Controller If the light sensor is enabled, there are two backlight levels to adjust. Press the left arrow or right arrow buttons to adjust. Press the OK button when finished. With the light sensor enabled, the backlight brightness will automatically change between the two levels, depending upon the ambient lighting conditions.
Operation TIME OUT This button displays a window that allows you to adjust the amount of time the unit stays awake after the last button press. The time is variable from 1 second to 120 seconds (the default is 10 seconds). Press the arrows to the left or right of the Time Out setting to adjust the time. Press the OK button when finished. This setting can have a significant effect on the run-time of the T3 between battery charges. During Sleep mode, the T3 uses virtually no battery power.
T3 Universal System Controller TILT SWITCH This button displays a window that allows you to adjust the settings for the built-in tilt sensor. The tilt switch is a motion detector that turns the remote on when activated. On means the tilt switch is active and will wake-up the T3 when it is moved. Off means the tilt switch is inactive. Press the OK button when finished.
Operation BATTERY This button displays a window that allows you to adjust the relative amount of time that the low battery icon appears on the display. This setting will determine how much time you have between the appearance of the low battery warning and the battery becoming completely depleted. Press the OK button when finished. The default warning time is Medium. Depending upon the age of the battery and your daily usage habits, it may be beneficial to adjust this time.
T3 Universal System Controller SOUND This button displays a window that allows you to adjust the volume of the audible speaker. The speaker sound provides feedback that a button was pressed. Press the arrows to the left or right to adjust the volume. Press the OK button when finished. There are six discrete volume settings. The lowest setting disables the speaker.
Operation CALIBRATE TOUCHSCREEN This button runs a routine that allows you to calibrate the touchscreen. Since it normally should not be necessary to calibrate the touchscreen, this routine is included as a precaution only. Warning: Do not attempt to calibrate the touchscreen with your fingertip. Proper calibration requires a stylus or other fine tip. Do not use metal objects such as ball point pens or screwdrivers that can damage the surface of the touchscreen. Press the Calibrate button to continue.
T3 Universal System Controller PROGRAMMING THE T3 The T3 is programmed using RTI’s TheaterTouch Designer software. RTI dealers can download the software free of charge from: www.rticorp.com/dealers A PC running Windows® 98SE or higher with a USB port is required. The required USB cable is included with the RTI IR-PRO dealer kit.
Chapter 4. Troubleshooting If you are having problems with your T3, please read these troubleshooting tips before contacting technical support. If you continue to have problems, see Chapter 5 for more information on contacting RTI technical support. DISPLAY IS DIM, BLANK OR UNREADABLE Make sure the battery pack connector is attached properly and the battery is charged. Try adjusting the backlight level from the Control Panel page (Refer to Chapter 3 for more details).
T3 Universal System Controller IR CODE PROBLEMS If you are using an IR repeater system, make sure it is working correctly with the original OEM remote. If not, you will need to troubleshoot the IR repeater system. If you are still having problems, try adjusting the IR code “Minimum Repeats” value in the TheaterTouch Designer programming software. If the IR code is executed inside a macro that contains multiple IR codes, try inserting a small time delay before the problem code.
Chapter 5. Service and Support UPDATES AND NEW PRODUCTS For news about the latest updates, new product information and accessories, please visit our web site at: www.rticorp.com CONTACTING REMOTE TECHNOLOGIES INCORPORATED For general info, you can contact RTI at: Remote Technologies Incorporated Tel. (952) 253-3100 Fax (952) 253-3131 info@rticorp.com www.rticorp.com RTI TECHNICAL SUPPORT At RTI, customer service and satisfaction is an utmost priority.
T3 Universal System Controller If you are having a problem with hardware, please note the equipment in your system, a description of the problem, and any troubleshooting you have already tried. If you are having a problem with software, please note what version you have installed, the operating system on your PC, a description of the problem, and any troubleshooting you have already tried.
Specifications Power 3.6 VDC, 1300 mAH Li-Ion Battery Pack Power Management Automatic On/Off (tilt switch) Infrared Control Range 30 Feet (9.1m) @ 60 Degrees Infrared Frequency Range 15kHz – 460kHz Radio Frequency Control Range Up to 100 Feet (30.
T3 Universal System Controller Battery Charge Time 3-4 Hours Total System Memory 32MBytes Flash (non-volatile) Device Capability Total number of devices limited only by memory Macro Capability Up to 64 steps per macro Total number of macros limited only by memory Macros allowed on every button Communications USB programming port Dimensions Length: 7.6 in. (193mm) Width: 3.1 in. (79mm) Height: 1.1 in. (28mm) Enclosure High-impact molded ABS plastic. Weight 7.4 oz.
® 7651 Anagram Drive Eden Prairie, MN 55344 Tel: 952-253-3100 Fax: 952-253-3131 www.rticorp.com © 2005 Remote Technologies Inc. All rights reserved. Printed in Taiwan.