Renault KOLEOS Vehicle user manual
A passion for performance ELF, partner of RENAULT recommends ELF Partners in cutting-edge automotive technology, Elf and Renault combine their expertise on both the racetrack and the city streets. This enduring partnership gives drivers a range of lubricants perfectly suited to Renault cars. Lasting protection and optimum performance for your engine – guaranteed.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections Getting to know your vehicle ............................... 1 Driving 2 ................................................................... Your comfort ......................................................... 3 Maintenance ......................................................... 4 Practical advice .................................................... ...................................... 6 ...............................................
0.
Section 1: Getting to know your vehicle Key, radio frequency remote control: general information, use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RENAULT card: general information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locking, unlocking the opening elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Opening and closing the doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) 3 2 1 5 4 1 Locks all the opening elements. 2 Unlocks all the opening elements. 3 Ignition and front door key. 4 Locking/unlocking the tailgate only. Remote control with switchblade key: 5 Locking/unlocking using the switchblade key. To release the insert from its housing, press button 5, it comes out automatically. Press button 5 and guide the insert back into its housing. Advice Avoid leaving the remote control in hot, cold or humid areas.
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surroundings: take care not to lock or unlock the doors by inadvertently pressing the buttons on the remote control. Note: If a door or the boot is open or not closed properly, the doors and boot lock/unlock in quick succession.
RADIO FREQUENCY REMOTE CONTROL UNIT: use The remote control A can be used to lock or unlock the doors and boot. It is powered by a battery which must be replaced (refer to the information on “Radio frequency remote control: batteries” in Section 5). Note: A With the engine running, the ignition switched on and in accessories position (refer to “Ignition switch: vehicles with a key” in Section 2), the remote control buttons will be inactive. 1 Locking the doors Press locking button 1.
RENAULT CARD: general information (1/2) 1 4 2 3 The RENAULT card is used for: RENAULT card operating range – locking/unlocking the doors and boot (see the following pages); This varies according to the surroundings. It is important to make sure when handling the RENAULT card that you do not lock or unlock the doors by inadvertently pressing the buttons.
RENAULT CARD: general information (2/2) 4 Advice Avoid leaving the card in hot, cold or humid areas. Do not keep the RENAULT card in a place where it could be bent or damaged accidentally, such as in a back pocket of a garment. Distance lighting function Depending on the vehicle, pressing button 4 switches on the dipped beam headlights and the interior lighting for approximately 20 seconds. This can be used, for example, to identify the vehicle from a distance when parked in a car park.
RENAULT CARD: usage (1/4) There are two ways to unlock/lock the vehicle: – the “hands-free” function; – RENAULT card buttons. 1 Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or locking the doors.
RENAULT CARD: usage (2/4) Locking using button 2 With the doors and boot closed, press button 2 on one of the front door handles. The vehicle will lock. The hazard warning lights flash twice to indicate that the vehicle is locked. Special features relating to vehicle locking 2 3 “Hands-free” unlocking Remote “Hands-free” locking With the RENAULT card in zone 1, press the button 2 on the handle of one of the two front doors: the vehicle will unlock.
RENAULT CARD: usage (3/4) NB: The maximum distance at which the vehicle locks depends on the surroundings. 4 5 Special features If the a door or the boot is open or not properly closed, the vehicle cannot be locked. The vehicle will lock/unlock in quick succession, but the hazard warning lights will not flash.
RENAULT CARD: usage (4/4) 7 Locking/unlocking only the boot Press the button 7 to lock/unlock the boot only. 1.10 Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or locking the doors.
LOCKING, UNLOCKING THE DOORS (1/3) If the remote control or, depending on the vehicle, the RENAULT card does not work In some cases, the radio frequency remote control or the RENAULT card may not work: – RENAULT card/radio frequency remote control battery worn or run flat, vehicle battery flat, etc. – use of appliances operating on the same frequency as the card (mobile phone, etc.
LOCKING, UNLOCKING THE DOORS (2/3) 4 3 A 4 1 Vehicles with RENAULT card Using the integrated key Access key 4 integrated in the card Insert the key 4 into the lock 1 and lock or unlock the front left-hand door. Slide the rear casing 3 downwards while pressing on zone A. 1.12 Once you are inside the vehicle, put the key back in its casing in the RENAULT card.
LOCKING, UNLOCKING THE DOORS (3/3) Locking the opening elements without the RENAULT card or the key For example, in the event of a discharged battery or the RENAULT card or key temporarily not working, etc. 5 6 With the engine switched off and a door or tailgate open, press and hold the switch 6 for more than five seconds. When the door is closed, all the doors and the tailgate will be locked.
OPENING AND CLOSING THE DOORS (1/2) 3 1 5 4 2 6 Opening the doors from the outside Opening from the inside Door/tailgate open buzzer With the doors unlocked, pull handle 1. If the vehicle is equipped with the knob 3, pull the handle 4 with the door unlocked. At a standstill, the warning light 5 lights up on the instrument panel alongside Special feature on vehicles equipped with a RENAULT card If the vehicle is not equipped with the knob 3, pull the handle 4.
OPENING AND CLOSING THE DOORS (2/2) 7 Vehicle with manual door locking To make it impossible for the rear doors to be opened from the inside, move lever 7 on each door and check from the inside that the doors are securely locked. Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time.
AUTOMATIC LOCKING WHEN DRIVING Activating/deactivating the function 2 1 To switch it on: with the vehicle at a standstill and the engine running, press the switch 1 until a beep sounds. To deactivate: with the vehicle at a standstill and the engine running, press the switch 1 until two beeps sound.
EMERGENCY CALL (1/2) If the vehicle is equipped with it, the emergency call is a system that allows the emergency services to be called automatically or manually in the event of an accident or illness, in order to reduce the time they take to arrive on the scene. If you use the emergency call function to report an accident which you have witnessed, this implies stopping where traffic conditions allow to allow the emergency services to locate your vehicle and therefore the location of the reported accident.
EMERGENCY CALL (2/2) Automatic mode In the event of unintended operation, it is possible to cancel the call by pressing switch 3 for 2 seconds before the call to the call centre is set up. When warning light 2 is on, this indicates that the automatic system is activated. Once a call is established, only the call centre can end the call. With ignition switched on, the emergency call is triggered automatically in the event of an accident with airbag activated.
FRONT HEADRESTS A A B 2 1 3 B 1 3 To raise the headrest To adjust side supports B To lower the headrest To refit the headrest Pull the headrest upwards to the desired height. Check that it is correctly locked. Press button 3 and guide the headrest down to the desired height. Check that it is correctly locked in place. To adjust the angle of the headrest Depending on the vehicle, move section A towards or away from you to the required position.
FRONT SEATS WITH MANUAL CONTROL Operating faults When an operating fault is detected, the integrated warning lights on the switch 4 for the seat concerned flash. 4 2 Consult an approved dealer. 3 1 To move the seat forwards or backwards Heated seats Lift handle 1 to unlock. Release the handle once the seat is in the correct position and ensure that the seat is locked. – pressing the switch 4 on the required seat for the first time activates the heating system at maximum power.
FRONT SEATS WITH ELECTRIC CONTROLS (1/2) To adjust the seat’s lumbar position Lower the handle 3 to increase the support and lift to decrease it. 1 2 3 For safety reasons, carry out any adjustments when the vehicle is not being driven. Adjusting the seat squab: – To move the seat forwards or back Move the switch 1 forwards or backwards. – To raise or lower the seat base Move the switch 1 up or down. Make sure that the seatbacks are correctly locked in place.
FRONT SEATS WITH ELECTRIC CONTROLS (2/2) With the ignition on: – pressing the switch 6 on the required seat for the first time activates the ventilation system at maximum power. Both integrated switch warning lights come on; 4 – a second press decreases the ventilation to minimum power. One integrated warning light comes on; – a third press switches off ventilation.
SEAT BELTS (1/4) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. Adjusting your driving position Incorrectly adjusted or twisted seat belts may cause injuries in the event of an accident. Use one seat belt per person, whether child or adult.
SEAT BELTS (2/4) Driver’s seat belt reminder and, depending on the vehicle, front passenger seat belt reminder This lights up on the central display when starting the engine then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approximately 12 mph (20 km/h), it flashes and a bleep sounds for around 120 seconds. Note: an object placed on the passenger seat base may activate the warning light in some cases.
SEAT BELTS (3/4) 7 8 Adjusting the height of the front seat belts Use button 7 to adjust the seat belt height so that the shoulder strap is worn as shown previously. Press the button 7 and raise or lower the seat belt. Make sure that the seat belt is locked in position correctly after you have adjusted it. 8 Rear seat belts 8 The belts are locked, unlocked and adjusted in the same way as the front belts. moved.
SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are composed of: – seat belt inertia reel pretensioners; – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Airbags for driver and front passenger Fitted to the driver and passenger side. The presence of this equipment is indicated by the word “Air bag” on the steering wheel and dashboard (air bag zone A) and, depending on the vehicle, a symbol on the lower section of the windscreen.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operating faults å This warning light will light up on the instrument panel when the ignition is switched on and then go out after a few seconds. If it does not light up when the ignition is switched on, or comes on when the engine is running, there is a fault in the system. Contact your approved Dealer as soon as possible. Your protection will be reduced until this fault is rectified.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
METHODS OF RESTRAINT IN ADDITION TO THE REAR SIDE SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (air bags, electronic control units, wiring) and the system components must not be reused on any other vehicle, even if identical.
SIDE PROTECTION DEVICES Side Airbags An airbag can be fitted to each front seat and the rear side seats, which are deployed on the side of the seat (door side) to protect the occupants in the case of a severe side impact. Curtain Airbags These are airbag fitted along the sides of the vehicle in the ceiling which trigger along the front and rear door side windows to protect the passengers in case of a severe side impact.
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. The airbag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
CHILD SAFETY: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
CHILD SAFETY: choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position for as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. 1.
CHILD SAFETY: choosing a child seat mounting (1/2) There are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
CHILD SAFETY: choosing a child seat mounting (2/2) The rings are located on the rear seatbacks and indicated by the symbol . 1 3 4 In all cases, attach the strap hook to the corresponding ring 3 and 4 and place the seat in the desired position. Pull the belt so that the back of the child seat comes into contact with the back of the vehicle seat.
CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. In the front seat The laws concerning children travelling in the front passenger seat differ in every country.
CHILD SAFETY: fitting a child seat, general information (2/2) In the rear side seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with their feet nearest the door. Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will go, although without allowing it to come into contact with the child seat.
CHILD SEATS: attachment by seat belt (1/3) ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. ² Seat not suitable for fitting child seats. Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt.
CHILD SEATS: attachment by seat belt (2/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
CHILD SEATS: attachment by seat belt (3/3) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°). (3) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest the door.
CHILD SEATS: attachment using the ISOFIX system (1/3) The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected.
CHILD SEATS: attachment using the ISOFIX system (2/3) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted. i-U = Suitable for the i-Size restraint devices in the “Universal” forward-facing and backward-facing category.
CHILD SEATS: attachment using the ISOFIX system (3/3) Child seat fitted using the ISOFIX mounting ü ± Seat which allows a ISOFIX child seat to be attached. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached. The anchorage points are located on the backs of the rear seats. ² Using a child safety system which is not approved for this vehicle will not correctly protect the baby or child.
CHILD SAFETY: deactivating, activating the front passenger air bag (1/3) 1 2 Deactivating the front passenger airbags (on equipped vehicles) Before fitting a child seat on the front passenger seat you must deactivate the passenger airbag. To deactivate the airbags: with the vehicle stopped and the ignition off, push and turn lock 1 to the OFF position.
CHILD SAFETY: deactivating, activating the front passenger air bag (2/3) A A 3 The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER fit a restraint system for a rear-facing child in a seat protected by an ACTIVATED front AIRBAG. This can cause the CHILD’S DEATH or SERIOUS INJURY. 1.
CHILD SAFETY: deactivating, activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbags activation/deactivation system is faulty. 1 Allowing any other passenger to sit in that seat is not recommended. Contact your approved dealer as soon as possible.
DRIVING POSITION: LEFT-HAND DRIVE (1/2) 1 2 25 3 24 4 5 6 23 7 22 8 9 1 2 10 11 21 20 19 1.
DRIVING POSITION: LEFT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Air vent. 2 Demister outlet. 3 Stalk for: – direction indicator lights; – exterior lights; – fog lights. 4 Cruise control/speed limiter controls. 5 Instrument panel. 6 Driver Airbag and horn location. 7 Controls for on-board computer information read-out and vehicle settings customisation menu. 8 Steering column stalk for windscreen and rear screen wash/ wiper.
DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 1 2 3 4 5 1 2 6 7 2 8 1 9 10 11 12 13 14 2 1 24 25 23 22 1.
DRIVING POSITION: RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Air vent. 2 Demister outlet. 3 Passenger Airbag location. 4 Controls for: – heated front seats, – ventilated front seats, – activation/deactivation of ECO mode, – activation/deactivation of assisted parking, – activation/deactivation of the Stop and Start function. 5 Heating or air conditioning controls. 6 Multifunction screen.
WARNING LIGHTS (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. In some cases, the appearance of a warning light is accompanied by a message. A 1 Instrument panel A: lights up when the driver’s door is opened. When the ignition is switched on, turn wheel 1 to set the brightness of the instrument panel. The © warning light means you should drive very carefully to an approved dealer as soon as possible.
WARNING LIGHTS (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. D A Brake circuit fault warning light It lights up when the ignition or the engine is switched on and goes off after a few seconds. If it comes on during braking and is accompanied by the ® warning light and a beep, it indicates that the fluid level in the circuit is low or that there is a braking system fault. Stop as soon as traffic conditions allow and contact an authorised dealer.
WARNING LIGHTS (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Ä A Toxic Fume Filter System Warning Light On vehicles which are equipped with it, this light comes on when the engine is started and, depending on the vehicle, when the ignition is switched off if the vehicle is in the engine standby phase (refer to the information on the “Stop and Start Function” in section 2) then goes out.
WARNING LIGHTS (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Rear seat belt reminder (depending on vehicle) A É Preheating warning light (diesel version) This should come on when the ignition is switched on. It indicates that the heater plugs are in operation. It goes out when preheating is complete. The engine can be started.
WARNING LIGHTS (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. ÐÏ A Speed limiter and cruise control indicator lights See the information on the “Speed limiter” and “Cruise control” in Section 2. Tyre pressure monitoring system Refer to the information on the “Tyre pressure monitoring system” in Section 2. ECO mode warning light This comes on when ECO mode is activated.
WARNING LIGHTS (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Driver’s seat belt reminder and, depending on the vehicle, front passenger seat belt reminder This lights up when the ignition is switched on, then, if the driver's or front passenger's (if this seat is occupied) seat belt is not fastened and the vehicle has reached approximately 12.4 mph (20 km/h), it flashes and a beep sounds for around 2 minutes.
DISPLAYS AND INDICATORS (1/2) 4 A 1 6 5 2 3 Instrument panel A Rev counter 4 Depending on the vehicle, you can customise your instrument panel with the content and colours of your choice. (graduations x 1000) Speedometer 5 From the multifunction screen , select “System”, then “User profile”. Refer to the handbook for the equipment. (km or miles per hour) Driving style indicator 3 Please refer to the information on “Ecodriving” in Section 2. 1.
DISPLAYS AND INDICATORS (2/2) A 2 1 8 9 7 Vehicles fitted with a navigation system On the multifunction screen, select “System” , “User profile” and “Unit”. Note: In both cases, once the battery is switched off, the on-board computer automatically returns to the original unit of measurement. Trip computer and warning system Refer to the information on the “Trip computer and warning system” in Section 1. Coolant temperature indicator 7 In normal use, indicator 7 should be before arear 8.
TRIP COMPUTER: general information Display selection keys 2 1 Scroll through the following information by repeated short presses on the control 2 (the display depends on the vehicle equipment and country): 2 a) total mileage and trip mileage recorder; b) journey parameters: – average fuel consumption; – current fuel consumption; – estimated range; – distance travelled; On-board computer 1 Depending on the vehicle, this includes the following functions: – distance travelled; – journey parameters; – infor
ON-BOARD COMPUTER: general information Interpreting some of the values displayed after resetting The values showing average fuel consumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed. 3 The average fuel consumption may decrease when: – the vehicle stops accelerating; Trip mileage resetting With “trip mileage recorder” selected on the display, press key OK 3 until the mileage recorder resets to zero.
ON-BOARD COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km a) Total mileage and trip mileage recorder. Average b) Journey parameters: 5.8 L/100 Current 7.4 L/100 1.64 Average fuel consumption since the last reset. The value is displayed after having travelled at least 400 metres since the last reset. Current fuel consumption.
ON-BOARD COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Range 541 km Interpreting the display selected Estimated range with remaining fuel. The value is displayed after driving 400 metres. Distance 522 km Average 123.4 km/h Distance travelled since last reset. Average speed since the last reset. The value is displayed after driving 400 metres. 1.
ON-BOARD COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections On-board computer with mileagebefore-service message Interpreting the display selected c) Mileage before service or oil change.
ON-BOARD COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections On-board computer with distance before next service message (cntd.) Service Intervals Oil change in 30 000 Kms / 24 mo Service due in 300 Kms / 24 days Service required Interpreting the display selected c) Mileage before service or oil change.
ON-BOARD COMPUTER: trip settings (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected d) Reset the tyre pressure. + No message memorised Tyre pressure Refer to the information on the “Tyre pressure monitoring system” in Section 2. e) Trip log. Successive display: – information messages (passenger airbag OFF etc.); – operating fault messages (Check injection system, etc.). 1.
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages « Parking brake on » Interpreting the display selected Indicates that the parking brake has been applied. « Checking control functions » Displayed with the ignition on when the vehicle is running self-diagnostics.
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given in the following pages.
TRIP COMPUTER AND WARNING SYSTEM: warning message These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Some examples of warning messages are given below. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
VEHICLE SETTINGS CUSTOMISATION MENU (1/2) Adjusting the settings (depending on the vehicle) Select the function to modify: 1 a) unlocking the driver’s door only; b) automatic locking of the doors while driving; c) hands-free function; d) indicator audio volume; e) internal welcome sound; f) external welcome; g) reading lamp in automatic mode; Depending on the vehicle equipment, this function allows you to activate/deactivate and adjust some of the vehicle’s functions.
VEHICLE SETTINGS CUSTOMISATION MENU (2/2) Adjusting the settings (depending on the vehicle) 2 Browse using the control 4 to select the function to adjust: 3 4 a) Language; b) Vehicle speed unit; c) Unlocking the driver’s door only; d) Lock doors when in motion; e) Use handfree card; f) Rear wipers when reverse is ON; g) Flashers volume; h) Welcome lights; Vehicles not fitted with a navigation system i) Automatic cabin lights; Accessing the settings menu on display 2 k) Parking assist audio volume;
STEERING WHEEL, POWER-ASSISTED STEERING (1/2) Power-assisted steering Variable power-assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. 1 Adjusting the steering wheel height and depth Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).
STEERING WHEEL, POWER-ASSISTED STEERING (2/2) 2 Activating the function With the ignition on, press the switch 3 , the warning light integrated in the switch lights up. Deactivating the function - Automatic: 3 Steering wheel heating (depending on the vehicle) This function heats the steering wheel in areas 2. Operating principle When the temperature is reached, the function regulates the temperature of the heated areas for approximately 30 minutes and then switches off automatically.
CLOCK AND EXTERIOR TEMPERATURE External temperature indicator 1 Special note: When the exterior temperature is - 3 °C to + 3 °C, the °C characters flash (signalling a risk of ice on the road). Display 1 Vehicles fitted with a touchscreen multimedia screen, navigation aid systems, etc. The time and exterior temperature are displayed on the multifunction screen 1. Refer to the handbook for the equipment.
REAR VIEW MIRRORS (1/2) Folding rear view mirrors B The door mirrors automatically fold in when the vehicle is locked using the button on the RENAULT card or remote “Hands-free” locking. In this case, when the engine is started, the door mirrors fold out. A 1 2 3 Welcome and goodbye function (depending on the vehicle) From the multifunction screen, select menu “Vehicle”, “User settings”, “External welcome” and activate or deactivate the function (ON or OFF).
REAR VIEW MIRRORS (2/2) Rear view mirror without lever 4 The rear-view mirror darkens automatically at night if you are being followed by a vehicle with its lights on. 4 Interior rear view mirror Its position can be adjusted. Rear-view mirror with lever 4 For night driving, to avoid being dazzled by the headlights of the car behind you, flip the small lever 4 located behind the rear view mirror. 1.
EXTERIOR LIGHTING AND SIGNALS (1/5) 2 1 1 k Dipped beam headlights Manual operation Turn ring 3 until the symbol is opposite mark 2. This indicator light on the instrument panel comes on. Automatic operation 3 š Side lights Turn ring 3 until the symbol is opposite mark 2. This indicator light on the instrument panel comes on.
EXTERIOR LIGHTING AND SIGNALS (2/5) Automatic main beam headlights 2 Depending on the vehicle, this system switches the main beam headlights on and off automatically. The function uses a camera located behind the interior rear-view mirror to detect vehicles that are following and coming in the opposite direction. The main beam headlights come on automatically if: – exterior light is weak; – no other vehicles or lighting are detected; – the vehicle speed is above approximately 30 mph (45 km/h).
EXTERIOR LIGHTING AND SIGNALS (3/5) 1 Daytime running lights function Switching off the lights The daytime running lights come on automatically with no action on stalk 1 when the engine is started, and they go off once the engine is switched off. – manually, move ring 3 to position 0; Operating faults 2 3 Operating faults When the message “Check auto lighting” appears on the instrument panel, the system is deactivated.
EXTERIOR LIGHTING AND SIGNALS (4/5) “See-me-home lighting” function This function allows you to briefly switch on the dipped beam headlights (to provide light when opening a gate, etc.). With the engine and lights switched off and the ring 3 in position 0 or AUTO, pull the stalk 1 towards you: the dipped beam headlights come on for approximately 30 seconds. To increase this duration, you may pull the stalk up to four times (total time limited to approximately 2 minutes).
EXTERIOR LIGHTING AND SIGNALS (5/5) f 4 1 Rear fog lights Turn centre ring 5 on the stalk until the symbol faces mark 4, then release it. Operation of the fog lights depends on the exterior lighting selected, and an indicator light will light up on the instrument panel. 5 g Do not forget to switch off the fog lights when they are no longer needed, to avoid inconveniencing other road users. Front fog lights Turn centre ring 5 on the stalk 1 until the symbol faces mark 4, then release it.
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. 1 2 One-touch mode A Horn Press the steering wheel boss A to activate the horn. Headlight flasher Pull stalk 1 towards you to flash the headlights. When driving, it is possible that the steering wheel may not be turned sufficiently to return the stalk automatically to its starting position.
HEADLIGHT BEAM ADJUSTMENT (1/2) For manual settings Examples of positions for adjusting control A according to the load 0 Driver alone or with front passenger or with one front passenger and two or three rear passengers A 1~2 On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the load.
HEADLIGHT BEAM ADJUSTMENT (2/2) When driving on the left in a lefthand drive vehicle (or vice versa), you must adjust your lights temporarily during your stay. 1 B Temporary adjustment for vehicles fitted with halogen headlights Open the bonnet and identify the marking B next to one of the front headlight projectors. For each headlight, using a screwdriver, turn the screw 1 by a quarter turn towards the - symbol to lower the beams.
WINDSCREEN WASH, WIPE (1/6) 1 1 2 A B C Check the condition of the wiper blades. You are responsible for their service life: D E Vehicle fitted with intermittent windscreen wipers A single sweep A short push will trigger one sweep of the wipers. B stop C intermittent wiping The wipers will pause for several seconds between sweeps. It is possible to change the time between sweeps by turning ring 2.
WINDSCREEN WASH, WIPE (2/6) 1 1 When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed. 2 F A B C D E Vehicle fitted with front windscreen wiper rain sensor The rain sensor is located on the windscreen, in front of the interior rear-view mirror. A single sweep A short push will trigger one sweep of the wipers. B stop 1.
WINDSCREEN WASH, WIPE (3/6) Operating fault Special note In the event of a malfunction of the automatic wiping, the wiper is set to intermittent wiping. Contact an authorised dealer.
WINDSCREEN WASH, WIPE (4/6) Specific front wiper position (service position) This position enables the blades to be lifted to remove them from the windscreen. It may be useful to: – to clean the blades; – to release the blades from the windscreen in winter; – replace the blades (please refer to the information on “Wiper blades” in Section 5). Note: Once the wipers have been switched off, at least 1 minute after locking the vehicle, it is possible to manually move the blades.
WINDSCREEN WASH, WIPE (5/6) Note: 1 A B In temperatures below zero, the washer liquid risks freezing to the windscreen, thereby reducing visibility. Heat the windscreen using the demister control before cleaning. C D E Windscreen washer With the ignition on, pull stalk 1 then release. A brief pull will trigger a single sweep of the wipers, in addition to the windscreen washer.
WINDSCREEN WASH, WIPE (6/6) Note: 1 To ensure the headlight washers operate correctly in winter, remove snow from the jet trims and de-ice the jet trims using an aerosol de-icer. A B C D E Headlight washers You are recommended to regularly remove dirt encrusted on the headlight glass. When the minimum windscreen washer fluid level is reached, the headlight washer system may be deprimed.
REAR SCREEN WASH, WIPE (1/2) To stop the operation, pivot ring 3 again. 1 2 3 Note: When washing using a roller type car wash, return the ring 3 on the stalk 1 to the stop position to deactivate automatic wiping. Follow usage recommendations. Check the condition of the wiper blades.
REAR SCREEN WASH, WIPE (2/2) Activation/deactivation of the rear screen wiper (depending on the vehicle) Engaging reverse gear triggers intermittent wiping (if the front wipers are in operation). If your vehicle is fitted with a vehicle settings customisation menu, you can opt to activate or deactivate this function. To do this, refer to the information on the “Vehicle settings customisation menu” in Section 1; “Rear wiping in reverse gear”.
FUEL TANK (1/3) Petrol version It is essential to use unleaded petrol. The octane rating (RON) must comply with the information given on the label on the cover A. Refer to Section 6 for information on “Engine specifications”. 2 A 3 Diesel version Only use diesel fuel which complies with the information on the label located inside the cover A.
FUEL TANK (2/3) Filling with fuel With the ignition off, insert the nozzle and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position throughout the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be sufficient space in the fuel tank to allow for expansion. Make sure that no water enters the fuel tank during filling.
FUEL TANK (3/3) Running out of fuel on diesel versions Vehicles with key/remote control – Put the ignition key in “On” position M (please see the information on the “Ignition switch” in Section 2) and wait for a few minutes before starting, to enable the fuel circuit to be primed; 4 No modifications whatsoever are permitted on any part of the fuel supply system (electronic units, wiring, fuel circuit, injectors, protective covers, etc.
1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting, stopping the engine: vehicle with key/remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in the highest gear, or 3,000 to 3,500 rpm. For the first 1,000 miles (1,500 km), do not exceed 80 mph (130 km/h) in the highest gear, or 2,500 rpm. After completing this mileage you may drive faster, although you may only expect top performance after approximately 3,600 miles (6,000 km). You may only expect top performance from your vehicle after approximately 1,800 miles (3,000 km).
IGNITION SWITCH: vehicle with key Ignition position 2. The ignition is switched on: Start position 3. If the engine fails to start at the first attempt, the key must be turned back before the starter can be activated again. Release the key as soon as the engine starts. Note: on diesel versions, several seconds may pass between turning the key and the engine starting to allow for engine preheating. Ignition switch “Stop and steering lock” position 0.
STARTING, STOPPING THE ENGINE: vehicle with key É Diesel versions – Turn the ignition key to the “Ignition on” position 2, and hold this position until the engine preheating light goes off; – turn the key to starter position 3 without depressing the accelerator pedal; – release the key as soon as the engine starts. Starting the engine Special note: if starting the engine when the outdoor temperature is very low (below -10°C): hold down the clutch pedal until the engine starts.
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (1/5) “Hands-free” starting with the tailgate open In this case, the RENAULT card should not be located in the boot, to avoid any risk of loss. 2 1 The RENAULT card must be inserted in detection zone 1. To start: – vehicles with an automatic gearbox, place the lever in position P, depress the brake pedal and press button 2; – vehicles with a manual gearbox, depress the brake or clutch pedal and press the button 2.
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (2/5) 3 Depress the brake or clutch pedal, then place the RENAULT 3 card (logo side) in contact with the start button 2 for around 2 seconds. Press the 2 button to start the vehicle. The message goes out. 2 Accessories function (switching on the ignition) Once you have gained access to your vehicle, you may use some of its functions (radio, navigation, wipers, etc.).
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (3/5) 2 Conditions for stopping the engine The vehicle must stationary, with the lever positioned in N or P for vehicles with an automatic transmission. With the RENAULT card in the vehicle, press the 2 button: the engine will stop. The steering column is locked when the driver’s door is opened or the vehicle is locked.
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (4/5) The remote engine start-up operates if: 4 6 3 – the lever is in neutral for vehicles with a manual or sequential gearbox; – the lever is in position P for vehicles with an automatic gearbox; – the ignition is off and no key is inserted into the ignition switch; 5 – the bonnet is closed; – all of the opening elements (doors and luggage compartment) are closed and locked when you leave the vehicle.
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (5/5) Do not use the engine remote start-up function or its programming when: – the vehicle is in a garage or in a confined space. Risk of poisoning or suffocation by exhaust gas emissions. – the vehicle is covered with a protective cover. Fire hazard. – the bonnet is open or before it opens. Risk of burns or serious injury.
STOP AND START FUNCTION (1/4) This system enables a reduced fuel consumption and lower greenhouse gas emissions. The system is activated automatically when the vehicle is started. While driving, the system stops the engine (standby) when the vehicle is at a standstill (traffic jam, traffic lights, etc).
STOP AND START FUNCTION (2/4) Preventing the standby of the engine Conditions for coming out of the engine standby In certain situations, such as a crossroads for instance, it is possible (with the system activated) to keep the engine running so as to be ready to move off quickly. For automatic gearboxes: Automatic gearbox: Keep the vehicle stationary with pressing the brake pedal slightly. Manual gearbox: Keep the clutch pedal pressed right down.
STOP AND START FUNCTION (3/4) Conditions for preventing the standby of the engine – parking distance control is in operation; Special cases for vehicles with a RENAULT card Certain conditions prevent the system from using the engine standby function, including when: – for vehicles with automatic gearboxes, the gradient is steeper than approximately 12%; for vehicles equipped with a RENAULT card: – the “Clear View” function is activated (please see “Automatic Climate Control” in Section 3); With the e
STOP AND START FUNCTION (4/4) Special feature of the automatic engine re-start The system is automatically reactivated each time the vehicle is started (see “Stop and Start function” in Section 2). Under certain conditions, the engine can restart on its own in order to guarantee your safety and comfort.
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected. If the message “Check antipollution system” is displayed along with warn- Ä ing lights and ©, consult an authorised dealer immediately.
GEAR LEVER Selecting reverse gear The ring 2 has to be lifted up to the gear lever knob to select reverse gear. The reversing lights will come on as soon as reverse gear is selected with the ignition on. 1 2 Gear lever Vehicles with manual gearbox: refer to the grid on the gear lever knob 1. Vehicles with an automatic gearbox: refer to the information on the “Automatic gearbox” in Section 2. 2.16 An impact to the underside of the vehicle while manoeuvring (e.g.
PARKING BRAKE 1 Parking brake To release: Depress the parking brake 1 firmly. The red warning light on the instrument panel will come on if you are driving with an incorrectly released parking brake. To apply: Depress the parking brake 1 firmly. Check that the vehicle is immobilised. The warning light on the instrument panel come on. — will Make sure that the parking brake is properly released when driving (red indicator light off), otherwise overheating, or even damage, may occur. 2.
ELECTRONIC PARKING BRAKE (1/3) Assisted operation Note: The assisted parking brake immobilises the vehicle when stopping the engine (and not when the engine is on standby for vehicles fitted with the Stop and Start function). Please refer to “Starting, stopping the engine” and “Stop and Start function” in Section 2. To indicate that the electronic parking brake is released, a beep sounds and the message “Apply parking brake” appears on the instrument panel: In all other instances, e.g.
ELECTRONIC PARKING BRAKE (2/3) 2 Brief stop Special cases To manually activate the electronic parking brake, (when stopping at a red light, or stopping when the engine is running, etc.): pull and release switch 1. The brake is released as soon as the vehicle is started up again. To park on a slope or while towing a trailer, for example, pull switch 1 for a few seconds to gain the maximum braking.
ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic gearbox In the event of message “Electric failure DANGER” or “Check battery”, manually activate the electronic parking brake by pulling switch 1 (or position the gear lever in P for automatic gearboxes) before stopping the engine. For safety reasons, automatic release is deactivated when the driver’s door is open or not shut properly and the engine is running (in order to prevent the vehicle from moving without the driver).
DRIVING ADVICE, ECO-DRIVING (1/5) Fuel consumption is accredited in accordance with a standard regulatory method. Identical for all manufacturers, this enables vehicles to be compared with one another. Consumption in real time depends on vehicle usage conditions, the equipment fitted and the user’s driving style. To optimise fuel consumption, please refer to the following advice.
DRIVING ADVICE, ECO-DRIVING (2/5) 4 This indicates: – average fuel consumption; – number of miles/kilometres travelled; – number of miles/kilometres saved. This corresponds to driving without fuel consumption (deceleration and/ or foot off the accelerator pedal). An overall rating from 0 to 100 is displayed to let you assess your eco driving performance. The higher the rating, the lower the fuel consumption. Eco advice is given to help improve your performance.
DRIVING ADVICE, ECO-DRIVING (3/5) ECO mode Disabling the function ECO mode is a function which optimises fuel consumption. This acts on all power consuming elements (engine power, switching gears for vehicles fitted with an automatic gearbox, heating and/or air conditioning, etc.). Press switch 4. Limiting acceleration enables low fuel consumption in urban and surrounding areas. The air conditioning and heating limiter enables you to save fuel without affecting your heating comfort.
DRIVING ADVICE, ECO-DRIVING (4/5) Driving advice, Eco-driving – Do not overrev the engine in the intermediate gears. You should always use the highest gear possible. – Avoid sudden acceleration. – Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on flat ground. Keep your foot in the same position on the accelerator pedal.
DRIVING ADVICE, ECO-DRIVING (5/5) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Recommendations for reducing consumption and therefore helping to preserve the environment: – Tyres Advice on use – An underinflated tyre increases fuel consumption.
MAINTENANCE AND ANTIPOLLUTION ADVICE Your vehicle complies with criteria for recycling and recovering vehicles at the end of their service life, which will come into force in 2015. Some of the parts on your vehicle have been designed to be recycled later. These parts are easily removable in order to be collected and reprocessed in recycling networks. Furthermore, by virtue of its design, moderate fuel consumption and initial settings, your vehicle also conforms to current anti-pollution regulations.
ENVIRONMENT Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the Renault eco² signature. Emissions Manufacture Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
TYRE PRESSURE MONITORING SYSTEM (1/3) 1 2 3 Resetting the standard level for the tyre pressures This should be done: – when the standard tyre pressure needs to be changed to adapt to usage conditions (empty, carrying a load, motorway driving, etc.); – after swapping a wheel (however this practice is not recommended); – after changing a wheel. It should always be done after checking the tyre pressure of all four tyres when cold.
TYRE PRESSURE MONITORING SYSTEM (2/3) « Puncture » A wheel B is shown in red, the warning 1 A light 4 comes on, the message “Puncture” appears and there is a beep. This message appears along with the ® warning light. They indicate that the affected wheel is punctured or severely underinflated. Replace it or contact an approved dealer if it is punctured. Top up the tyre pressure if the wheel is deflated.
TYRE PRESSURE MONITORING SYSTEM (3/3) “Tyres location failure” Replacing wheels/tyres This message “Tyres location failure” appears when driving if one or more wheels have been fitted with sensors not recognised by Renault. This system requires specific equipment (wheels, tyres, hubcaps, etc.). Please see the information on “Tyres” in Section 5.
DRIVING CORRECTION DEVICES AND AIDS (1/4) Depending on the vehicle, they will consist of: – ABS (anti-lock braking system) ; – ESC (electronic stability control) with understeer control and traction control; – emergency brake assist; – hill start assistance. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions. However, the functions do not take the place of the driver.
DRIVING CORRECTION DEVICES AND AIDS (2/4) Electronic stability control ESC with understeer control and traction control Electronic stability control ESC This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
DRIVING CORRECTION DEVICES AND AIDS (3/4) 1 The traction control system offers additional safety. It is recommended that you do not drive with the function disabled. Correct this as soon as possible by pressing the switch 1 again. Note: The function is reactivated automatically when the ignition is switched on or when a speed of approximately 24 mph (40 km/h) is exceeded. Emergency brake assist This system supplements the ABS and helps reduce vehicle stopping distances.
DRIVING CORRECTION DEVICES AND AIDS (4/4) Hill start assistance Depending on the gradient of the incline, this system assists the driver when starting on a hill. It prevents the vehicle from rolling backwards by automatically applying the brakes when the driver lifts his/her foot off the brake pedal to depress the accelerator pedal.
TRANSMISSION: 4-wheel drive (4WD) (1/4) Mode selector “2WD” mode Depending on the road conditions, turning the selector 1 enables the following modes to be selected: To activate this mode, turn the selector 1 to the “2WD” position. The warn- – AUTO ; – 2WD ; Remember that driving a vehicle offroad is very different to driving it on the road. To make the most of your vehicle in an off-road situation, we recommend that you are trained to drive a 4x4 (4WD) vehicle.
TRANSMISSION: 4-wheel drive (4WD) (2/4) “4WD Lock” mode To activate this mode, turn selector 1 to the “4WD Lock” position. The selector the returns to the “AUTO” position. The ’ Note: If the vehicle speed exceeds approximately 24.8 mph (40 km/h) in “4WD Lock” mode, the system automatically switches back to “AUTO” mode. indicator light will light up on the instrument panel.
TRANSMISSION: 4-wheel drive (4WD) (3/4) After stopping the engine, the system may take up to five minutes to cool down. If the system detects excessive wheelspin on the front wheels, it adapts the engine to run in a way that reduces wheelspin. Electronic stability program and traction control when driving offroad Anti-lock braking in LOCK mode In this case, only individual wheel braking remains active.
TRANSMISSION: 4-wheel drive (4WD) (4/4) All-wheel drive system – Irrespective of the mode selected, do not start the engine if one or more wheels are not in contact with the ground (eg. when the vehicle is on a jack or roller bench). – Do not turn the mode selector when cornering, reversing or if the wheels are spinning excessively. Only select the “2WD”, “AUTO” or “4WD Lock” mode when the vehicle is being driven in a straight line. – Only use tyres which meet the required specifications.
ACTIVE EMERGENCY BRAKING (1/10) Active emergency braking The system has two types. Depending on the vehicle, one of the two systems is equipped in the vehicle. - System A; 1 2 - System B. The system only detects vehicles driving in the same direction of traffic. The system cannot detect motorcycles because of the difficulty in forecasting their trajectory. This function is an additional driving aid.
ACTIVE EMERGENCY BRAKING (2/10) Press the switch 5 OK again to activate or deactivate the function: 3 = < 5 6 4 function activated function deactivated is displayed on The warning light the instrument panel when the system is deactivated. This system is reactivated each time the ignition is switched on.
ACTIVE EMERGENCY BRAKING (3/10) System A (continued) Operating faults When the system detects an operating warning light lights up fault, the on the instrument panel, with the message “Active braking disconnected”. There are two possibilities: – the system is temporarily disrupted (for example: radar obscured by dirt, mud, snow etc.). In this case, park the vehicle and switch off the engine. Clean the detection zone of the radar.
ACTIVE EMERGENCY BRAKING (4/10) Limitation of the system operation – The system will only respond to vehicles which are moving or which have been sensed as moving. – The radar area should be kept clean and free of any modifications in order to ensure the proper operation of the system. – The system cannot respond to small vehicles such as motorbikes or bicycles as effectively as to other vehicles. – The system may not operate properly when the road surface is slippery (rain, snow, black ice etc.).
ACTIVE EMERGENCY BRAKING (5/10) 7 This system can apply maximum braking to the vehicle until it is completely stationary if necessary. System B If your vehicle is equipped with system A, please refer to the information on “System A” in previous pages. Using information from the radar-camera 7, the system calculates the distance which separates it from the vehicle in front and the surrounding pedestrians. It notifies the driver if there is a risk of head-on collision.
ACTIVE EMERGENCY BRAKING (6/10) System B (continued) Special features Operation When the vehicle speed: When driving (speed between about 4.34 and 99.2 mph (7 and 160 km/h)), if there is a risk of collision with the vehicle in front, the system: 2 – is between about 27.9 mph (45 km/h) and 48 mph (80 km/h) approximately, the warning is activated. Braking will only be triggered if the vehicle preceding you is moving.
ACTIVE EMERGENCY BRAKING (7/10) Press the switch 5 OK again to activate or deactivate the function: 3 = < 5 6 4 System B (continued) For vehicle not fitted with a navigation system Activating or deactivating the system – With the vehicle at a standstill, press and hold the switch 5 OK to access the settings menu, For vehicles fitted with a navigation system – repeatedly press the control 6 up or down until you reach the “Driving assistance” menu.
ACTIVE EMERGENCY BRAKING (8/10) System B (continued) Conditions for non-activation of the system The system cannot be activated: – when the gear lever is in neutral; – when the parking brake is activated; – while cornering. As a general rule, if the driver shows signs of attention (action on the steering wheel, pedals etc.), the system delays its operation or does not activate. 2.
ACTIVE EMERGENCY BRAKING (9/10) Active emergency braking This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The triggering of this function may be delayed or prevented when the system detects clear signs of control of the vehicle by the driver (action on the steering wheel, pedals etc.).
ACTIVE EMERGENCY BRAKING (10/10) Limitation of the system operation – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The radar-camera area on the windscreen should be kept clean and free of any modifications in order to ensure the proper operation of the system. – The system cannot respond to small vehicles such as motorbikes or bicycles as effectively as to other vehicles.
LANE DEPARTURE WARNING (1/3) This system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. – – – – – – This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road. However, the function is not intended to replace the driver.
LANE DEPARTURE WARNING (2/3) 2 3 1 4 Activation/deactivation Vehicles fitted with a navigation system From the multifunction screen 2: select “Vehicle”, “Driving assistance”, “Lane departure warning” then choose “ON” or “OFF”. You can access menu “Driving assistance” directly from button 1 . 2.50 Vehicles not fitted with a navigation system Press the switch 3.
LANE DEPARTURE WARNING (3/3) Adjustment 2 5 6 Conditions for non-activation of alerts – Direction indicators activated for less than around 2 seconds prior to departing from the lane; – very fast lane departure; – driving continuously on a line; – on bends, the function allows for slightly cutting the bend; – hazard warning lights activated; – ... Vehicles fitted with a navigation system From the multifunction screen 2, select “Vehicle”, “Driving assistance”, “Lane departure warning settings”.
BLIND SPOT WARNING (1/4) 1 A A This system alerts the driver to other vehicles in the detection zone A. The system is activated when the vehicle’s speed is between approximately 30 km/h (19 mph) and 140 km/h (87 mph). This function uses sensors 1 installed in the front and rear bumper of both sides. 2.52 Special feature Make sure that the sensors are not obscured (by dirt, mud, snow, etc.). If a sensor is obscured, the message “Blind spot clean sensor” will appear on the instrument panel.
BLIND SPOT WARNING (2/4) – repeatedly press control 5 up or down until you reach the “Blind spot alert” menu, then press the switch 4 OK. 2 4 5 – Press the switch 4 OK again to activate or deactivate the function. 3 Activation/deactivation Vehicles fitted with a navigation system On the multifunction screen 2, select the “Vehicle” menu, “Driving assistance”, and “Driving assistance”, and then choose “ON” or “OFF”. You can access menu “Driving assistance” directly from button 3 .
BLIND SPOT WARNING (3/4) Display B 16 The function is activated and has not detected any vehicles. B 6 C 7 Indicator 6 Operation An indicator light 6 is located on each door mirror 7. This function will indicate: – when the vehicle speed is between approximately 30 km/h (19 mph) and 140 km/h (87 mph); – when another vehicle is in the blind spot area and travelling in the same direction as your vehicle.
BLIND SPOT WARNING (4/4) 6 B C Operating faults If the system detects a fault, the message “Check blind spot alert” is displayed on the instrument panel. Consult an authorised dealer. Note: When the engine is started, the indicator light 6 (display B) flashes three times. It is normal. D Conditions for non-function – If the object is not moving; – if traffic is heavy; – the road is winding; – if front and rear sensors both detect objects at the same time (e.g. when passing an articulated lorry). – ...
OVERSPEED ALERT (1/3) Operating principle 1 The system detects speed limit signs on the side of the road and displays the speed limit. It mainly uses information taken from the camera 1, attached to the windscreen behind the rear-view mirror. Note: make sure the windscreen is not obscured (dirt, mud, snow, condensation etc.). For vehicles which are equipped with it, the system also uses information from the navigation system.
OVERSPEED ALERT (2/3) 2 3 a 5 6 – repeatedly press the control 6 up or down until you reach the Speed alert menu, then press the switch 5 OK. – press OK to turn the function on or off. Varying the limit speed 4 b Activating/deactivating the system Vehicles fitted with a navigation system On the multifunction screen 2, select the “Vehicle” menu, “Driving assistance”, and “Speed alert settings”, and then choose “ON” or “OFF”.
OVERSPEED ALERT (3/3) Operating fault The system cannot detect the speed limit if: – the windscreen is not clean; This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. – the camera is blinded by the sun; The driver should always adapt their speed to the traffic conditions, regardless of the system indications.
SPEED LIMITER FUNCTION (1/3) Switching on a 3 2 1 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. b 4 Press switch 1 on side . The indicator light comes on, lit orange, and the message “Speed limiter” appears on the instrument panel, accompanied by dashes to indicate that the speed limiter function is activated and waiting to store a limited speed.
SPEED LIMITER FUNCTION (2/3) a Varying the limit speed Exceeding the limit speed The speed limiter can be changed by repeatedly pressing the switch 2: It is possible to exceed the limit speed at any time. To do this: press the accelerator pedal firmly and fully (beyond the resistance point). – side a (+) to increase the speed; – side b (-) to reduce the speed. 2 While the speed is being exceeded, the speed limiter flashes red on the instrument panel.
SPEED LIMITER FUNCTION (3/3) Recalling the limit speed If a speed has been saved, it can be recalled by pressing switch 3 ((R)). a 3 2 1 4 Putting the function on standby Switching off the function The speed limiter function is deactivated if you press switch 1: in this case a speed is no longer stored. The orange warning light and message on the instrument panel goes out to confirm that the function is deactivated. The speed limiter function is suspended when you press switch 4 (O).
CRUISE CONTROL FUNCTION (1/4) a 3 2 b 4 1 The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). Controls 1 Main “On/Off” switch. 2 Controls for: a cruising speed activation, storage and increase (+); b decreasing cruising speed (-). 3 Activation with recall of saved cruising speed (R). 4 Switch the function to standby (with cruising speed saved) (O).
CRUISE CONTROL FUNCTION (2/4) Activating cruise control At a steady speed (above approx. 20 mph (30 km/h)), press the switch 2 on side a (+): the function is activated and the current speed is saved. The cruising speed replaces the dashes and cruise control is confirmed by the appearance of the message “Check cruise control” and the warning light . 1 a 2 If you try to activate the function below 20 mph (30 km/h), the message “Invalid speed” will be displayed and the function will remain inactive.
CRUISE CONTROL FUNCTION (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelerator pedal. While overtaking, the cruising speed flashes red on the instrument panel. a Then, release the accelerator: after a few seconds, the vehicle will automatically return to its set cruising speed.
CRUISE CONTROL FUNCTION (4/4) Returning to the cruising speed a 3 2 4 Putting the function on standby The function is set to standby if you: – use the switch 4 (O); – the brake pedal; – depress the clutch pedal or the shift into neutral if the vehicle has an automatic gearbox. In these three cases, the cruising speed remains stored and the message “Memorised” accompanied by this speed appears on the instrument panel.
ADAPTIVE CRUISE CONTROL (1/8) The adaptive cruise control is a function which gives you the option, when traffic conditions permit (large free-flowing road or motorway), of maintaining a chosen speed, known as the cruising speed, while keeping a safe distance from the vehicle in front in the same lane. The function can be adjusted from 31 mph (50 km/h) to 99.2 mph (160 km/h). The radar-camera has a range of around 120 metres.
ADAPTIVE CRUISE CONTROL (2/8) a 3 6 2 b 4 5 Controls 5 Main “On/Off” switch. 2 Controls for: a cruising speed activation, storage and increase (+); b decreasing cruising speed (-). 3 Activation with recall of saved cruising speed (R). 4 Switch the function to standby (with cruising speed saved) (O). 6 Adjusting following distance. Switching on Press switch 5 on the side showing .
ADAPTIVE CRUISE CONTROL (3/8) Driving Varying the following distance Once a cruising speed is memorised and the cruise control function is active, you may lift your foot off the accelerator pedal. If a following distance is stored and a vehicle travelling slower than yours is detected by the system in your lane, your vehicle will brake (with the brake lights on) and adapt its speed to that of the vehicle in front, respecting the following distance selected previously.
ADAPTIVE CRUISE CONTROL (4/8) Putting the function on standby The function is set to standby if: a 3 – you press switch 4 (O); – you depress the brake pedal; – you depress the clutch pedal; 2 – you use the gear lever; 4 – the engine speed is too low or too high; – the vehicle speed is lower than 24.8 mph (40 km/h) or over 105.4 mph (170 km/h); Exceeding the cruising speed – certain driver correction devices and aids are triggered (ABS, ESC, etc.
ADAPTIVE CRUISE CONTROL (5/8) Under certain conditions (coming up behind a vehicle moving more slowly, rapid change of lane of vehicles in front etc.), the system may not have time to respond and may emit a beep alongside the alert A when the situation requires the driver’s attention, or the alert B when the situation requires immediate action from the driver. A React accordingly and perform the appropriate manoeuvres.
ADAPTIVE CRUISE CONTROL (6/8) Operating faults When the system detects an operating fault the message “Check cruise control” appears on the instrument panel. There are two possibilities: 5 Switching off the function The cruise control function is stopped if you press switch 5 on the side; in this case a speed is no longer stored. The green indicator light and the message “Adaptive cruise ctrl” on the instrument panel go out to confirm that the function is deactivated.
ADAPTIVE CRUISE CONTROL (7/8) This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The driver should always adapt their speed to the traffic conditions, regardless of the system indications. The system should under no circumstances be taken to be an obstacle detector or an anti-collision system.
ADAPTIVE CRUISE CONTROL (8/8) – – – – – – – – Limitation of the system operation – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The radar-camera should be kept clean and free of any modifications in order to ensure the proper operation of the system. Fixed obstacles (stationary vehicles, traffic jams, toll booths etc.) or objects travelling at low speed or of a small size (motorbikes, bicycles, pedestrians etc.
PARKING DISTANCE CONTROL (1/5) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the vehicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 20 to 30 centimetres from the obstacle. 1 This function is an additional aid that indicates the distance between the vehicle and an obstacle whilst reversing, using sound signals.
PARKING DISTANCE CONTROL (2/5) 2 A C B Note: the display 2 shows the vehicle surroundings and emits beeps. It is necessary to travel a few metres before the side detection is activated. If all areas have a grey background, the whole area around the vehicle is being monitored: – A: analysis of the vehicle surroundings in progress; – B: analysis of the vehicle surroundings carried out Operation Most objects located less near the front, rear and sides of the vehicle are detected.
PARKING DISTANCE CONTROL (3/5) If a side obstacle is detected: D – the beeps become faster and then sound continuously as the obstacle gets nearer. Green, orange and red zones will be displayed on the display D; 3 Detection of obstacles to the side Depending on the direction of the wheels, the system determines the trajectory of the vehicle and notifies the driver of any risk or otherwise of a collision with an obstacle 3 to the side of the vehicle.
PARKING DISTANCE CONTROL (4/5) 4 System sound Enables the system sound to be selected from a choice of 3. Deactivating the system sound Activate or deactivate the parking distance control sound. 5 6 Note: If you deactivate the sound, you will no longer be notified with beeps when approaching an obstacle. Deactivating the system Activate or deactivate parking distance control. Adjustment You can adjust certain settings from the multifunction screen 4.
PARKING DISTANCE CONTROL (5/5) Automatic deactivation of the parking distance control The system deactivates: – when the vehicle speed is above approximately 6 mph (10 km/h); – depending on the model, when the vehicle is stationary for more than approximately 5 seconds and an obstacle is detected (such as when in a traffic jam, etc.); – when the vehicle is in neutral for manual gearboxes, or in position N or P for automatic gearboxes.
REVERSING CAMERA (1/2) 2 3 4 C 3 4 B 1 A Operation Fixed gauge 3 4 moving guide line: Moving into reverse gear, the camera 1 located on the tailgate provides a view of the area behind the vehicle on the multimedia screen 2, accompanied by one or two moving or fixed guide lines 4 and 3. The fixed clearance gauge comprises coloured markers A, B and C, indicating the distance behind the vehicle: This is shown in blue on the multifunction screen 2.
REVERSING CAMERA (2/2) 2 Activating, deactivating the reversing camera From the multifunction screen 2, select “Vehicle”, “Settings”, “Parking assistance”, then “Rear view camera”. Activate or deactivate the reversing camera and confirm your choice. You can also adjust the camera image settings (brightness, contrast, etc.) The screen shows a reverse mirror image.
ASSISTED PARKING (1/6) Look in all directions 2 Select indicator 3 1 This function assists with parking manoeuvres. Take your hands off the steering wheel. You only control the pedals and the gear lever. You can retake control at any time by operating the steering wheel. Switching on Special features With the vehicle at a standstill or driving at less than approximately 18.6 mph (30 km/h), press switch 1.
ASSISTED PARKING (2/6) Choice of manoeuvre The system can perform four types of manoeuvres: –4 parallel parking; –5 perpendicular parking; –6 angle parking; Look in all directions Look in all directions Select indicator Reverse 9 4 5 6 7 – 7 moving out of a parallel parking space. From the multifunction screen, select the manoeuvre to be performed. And activate the direction indicator (turn signal) on the side you wish to park.
ASSISTED PARKING (3/6) Special note Look in all directions Press and hold (icon) button to start – Drive slowly and always be ready to use the brake; – The system can not detect parking spaces between objects except for vehicles such as a post, motorbike or obstacle; 1 – The system can not detect parking spaces made after detecting or before detecting; – Maintain the distance about 50~150 cm from the parked vehicles when looking for parking spaces.
ASSISTED PARKING (4/6) Look in all directions Go forward or reverse Special note – While exiting the parking space, the system is disrupted for safety when there is risk to impact with obstacles; – The system may not be operated when the space is small; – When exiting or parking the space, drive forwards or backwards after rotating steering wheel.
ASSISTED PARKING (5/6) Suspending the manoeuvre The manoeuvre is suspended in the following circumstances: – you take control of the wheel; – a door or the boot is opened; – the vehicle is at a standstill for too long; – an obstacle in the direction of movement prevents the manoeuvre from being completed; – the engine will stop. Once the warning light on the instrument panel goes off and a beep sounds, the manoeuvre has been suspended.
ASSISTED PARKING (6/6) This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. Make sure that the manoeuvre complies with the applicable traffic regulations at your location. – The driver should always look out for sudden hazards during driving: always ensure that there are no moving obstacles (such as a child, animal, pram, bicycle, etc.
AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode Move lever 1 to position D. 3 2 In most road conditions you will encounter, you will not need to touch your lever again: the gears will change automatically at the right time and at the most suitable engine speed because the automatic system takes into account the vehicle load and road contour and adjusts itself to the particular driving style you have chosen.
AUTOMATIC TRANSMISSION (2/3) 1 Special cases Special circumstances In certain driving conditions (for example, engine protection, operation of the Electronic Stability Programme: the automatic system may change gear automatically. Likewise, to prevent incorrect manoeuvres, a gear change may be refused by the automatic system: in this case the gear display flashes for a few seconds as a warning. – If the bends and road surface do not allow you to stay in automatic mode (e.g.
AUTOMATIC TRANSMISSION (3/3) Parking the vehicle Operating faults When the vehicle is stopped, move the lever to position P while keeping your foot on the brake pedal: the gearbox is in neutral and the drive wheels are mechanically locked by the driveshaft. – when driving, if the ‘check gearbox’ message appears on the instrument panel, it indicates a fault. Apply the parking brake or, depending on the vehicle, ensure that the electronic parking brake is applied.
2.
Section 3: Your comfort Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual air conditioning/heating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air conditioning: information and advice on use . . . . . . . . .
AIR VENTS, air outlets (1/2) 3 3 2 2 4 5 6 1 7 7 1 left-hand air vent 2 side window demister outlets 3 windscreen demisting vents 4 centre air vents 5 right-hand air vent 6 multifunction screen 7 footwell heater outlets for front passengers 8 footwell heater outlets for rear passengers 9 centre air vents for rear seats 3.
AIR VENTS, air outlets (2/2) 10 13 13 15 14 12 11 Centre air vents. Side air vents Air flow Air flow Move the control knob 11 or 12 (beyond the resistance point). Move the control knob 14 or 15 (beyond the resistance point). 11 left or 12 right: closed. 14 left or 15 right: closed. 11 right or 12 left: maximum air flow. 14 right or 15 left: maximum air flow. Direction Direction Move the cursors 10 to the desired position. Move the cursors 13 to the desired position.
MANUAL AIR CONDITIONING (1/3) 1 2 3 4 A 5 9 8 7 6 The controls Indicators 1 Adjusting the air temperature. The following indicators are displayed on the multimedia screen A: 2 De-icing/demisting of the rear screen and, depending on the vehicle, the door mirrors. 3 Air conditioning. 4 Air recirculation. 5 Adjusting air distribution in the passenger compartment. 6 Adjusting the ventilation fan speed. 7 Adjusting the ventilation speed and stopping the system. 8 “Clear view” function. 3.
MANUAL AIR CONDITIONING (2/3) Distribution of air in the passenger compartment There are five air distribution options. Turn control 5 to choose the distribution option. 4 5 The air distribution is displayed on the multimedia screen. The air flow is directed to the windscreen and the front side window demisting vents. õ ÷ The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells.
MANUAL AIR CONDITIONING (3/3) Clear view function 1 2 5 Press button 8 - the intrgrated indicator light comes on. This function quickly demists and deices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-icing functions must be activated. 8 7 6 Press button 2 to stop the heated rear screen operating, and the intrgrated indicator goes out. To exit this function, press button 8 again.
AUTOMATIC CLIMATE CONTROL: Controls A (1/5) A 8 9 Automatic mode 10 2 18 11 3 1 7 6 5 4 17 16 15 14 13 11 12 13 Controls A 11 Ventilation speeds. Press zone 14 to access the multifunction screen 2. The presence of the controls detailed below will depend on the vehicle model. 12 Distribution of air in the passengercompartment. 1 and 3 Left and right temperature indication adjustment. 4 De-icing/demisting of the rear screen and, depending on the vehicle, the door mirrors.
AUTOMATIC CLIMATE CONTROL: Controls A (2/5) A 19 11 1 11 3 15 14 Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. You can still adjust the ventilation speed by pressing buttons 11 or by sliding or touching your finger in zone 19. Depending on the vehicle, the ventilation speed, which is no longer controlled automatically, appears in zone 19 and zone 14. 3.
AUTOMATIC CLIMATE CONTROL: Controls A (3/5) 8 A To exit this function, press either: 10 9 – button 7; – again button 5; – on button 8, 9 or 10. 19 11 7 11 5 4 Clear View function This function quickly demists and deices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). It imposes automatic operation of the air conditioning and rear screen de-icing and, depending on the vehicle, the windscreen electric de-icer.
AUTOMATIC CLIMATE CONTROL: Controls A (4/5) Rear screen de-icing/ demisting A Press button 3 – the integrated indicator light comes on. This function enables rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). 18 To exit this function, press button 3 again. Demisting automatically stops. 17 4 3 Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions.
AUTOMATIC CLIMATE CONTROL: Controls A (5/5) 8 A Air recirculation 10 9 Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle; 16 6 4 Adjusting the distribution of air in the passenger compartment Press buttons 12 to select the desired distribution (a warning light is displayed in zone 14): The air flow is mainly directed to the demisting vents for the windscreen and the side windows.
AUTOMATIC CLIMATE CONTROL: Controls B and C (1/5) B 11 12 C 11 13 14 13 13 2 3 5 7 Controls B and C 6 1 Left temperature indication adjustment, “Clear View” function. 2 “DUAL" function. 3 Automatic modes (SOFT, AUTO, FAST). 4 Air conditioning ON/OFF. 5 Right temperature indication adjustment, De-icing/demisting of the rear screen and, depending on the vehicle, the door mirrors ON/OFF. 6 and 10 Ventilation speeds. 7 Distribution of air in the passenger compartment.
AUTOMATIC CLIMATE CONTROL: Controls B and C (2/5) B C 1 10 2 6 5 2 1 5 15 10 6 Varying the ventilation speed Temperature adjustment In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. There are two types of settings: The displayed temperature values show a comfort level.
AUTOMATIC CLIMATE CONTROL: Controls B and C (3/5) To exit this function, press either: C B – again button 1; – one of the buttons 3. 3 3 1 5 10 6 Clear View function This function quickly demists and deices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). It imposes automatic operation of the air conditioning and rear screen de-icing and, depending on the vehicle, the windscreen electric de-icer. 3.
AUTOMATIC CLIMATE CONTROL: Controls B and C (4/5) B C 10 9 14 Rear screen de-icing/ demisting 14 Press button 5 – the integrated indicator light comes on. This function enables rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). 4 4 5 5 10 9 Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions. To exit this function, press button 5 again.
AUTOMATIC CLIMATE CONTROL: Controls B and C (5/5) Air recirculation C B 14 Depending on the vehicle or country, Press button 8 or 9. 14 Note: 9 8 7 Adjusting the distribution of air in the passenger compartment Press buttons 7 to select the desired distribution (a message is displayed in zone 14): The air flow is mainly directed to the demisting vents for the windscreen and the side windows.
AIR CONDITIONING: information and advice on use Advice on use Fuel consumption Operating faults In some situations, (air conditioning off, air recirculation activated, ventilation speed at zero or low, etc.) you may notice that condensation starts to form on the windows and windscreen. You will normally notice an increase in fuel consumption (especially in town) when the air conditioning is operating. As a general rule, contact your approved dealer in the event of an operating fault.
OUTSIDE AIR QUALITY AND DEODORISATION FUNCTION Take care A Deodorization cycle On With the air conditioning switched on, from the screen A, select Menu, Vehicle, Take care. Deodorisation function Outside air quality Deodorization cycle The air quality is given using a graph on the multifunction screen.
ELECTRIC WINDOWS (1/2) Passenger safety The driver can prevent the front and rear passenger electric windows from operating (and the driver’s window) by pressing switch 2. A confirmation message is displayed on the instrument panel. Driver’s responsibility Never leave your vehicle with the RENAULT card or key inside, and never leave a child, adult who is not self-sufficient or a pet, even for a short while.
ELECTRIC WINDOWS (2/2) One-touch mode Operating faults Depending on the vehicle, this mode works in addition to the operation of the electric windows described previously. It is only fitted to the driver’s window. Briefly press or pull switch 1 fully: the window is fully lowered or raised. Pressing the switch again stops the window moving.
ELECTRIC SUNROOF (1/2) 1 A B 2 To slide the curtain 1 With the ignition on: – Full opening: push switch 2 to the middle of position A; – Full closing: push switch 2 to the end of position B. It doesn’t need to be held. The curtain will automatically open or close all the way. To tilt the sunroof When the sunroof is closed, press switch 2 to tilt up the sunroof. It doesn’t need to be held. When the sunroof is tilt, press switch 2 to close the sunroof. It doesn’t need to be held.
ELECTRIC SUNROOF (2/2) A It doesn’t need to be held. The sunroof will automatically open or close all the way. To stop the window, push the switch once more while it is opening or closing. – check that the sunroof is properly closed before leaving your vehicle; Note: If you wish to open the sunroof while driving, comfort opening is recommended to prohibit wind buffeting. – do not open the sunroof immediately after it has rained or immediately after washing the vehicle.
INTERIOR LIGHTING (1/3) 3 2 1 4 5 Interior lights switch 1 Press switch 1 to turn on/off map reading light 3 and 4. When a door is open, door light 5 and foot light 6 are ON. Interior lights switch 2 Note: For vehicles fitted with a navigation system, you can use the multifunction screen to deactivate/activate the courtesy lights which come on when the doors or boot are opened. To do this, please refer to “Vehicle settings customisation menu” in Section 1.
INTERIOR LIGHTING (2/3) 7 8 9 10 11 Map reading lights switch 7, 8 Press switch 7, 8 to turn on/off left orright map reading light independently. Front mood light 9 Front mood light 9 comes on when the illumination is turned on. 3.24 Front and rear door ambient light Front and rear door ambient light 10 comes on when the door is opened. Front door storage light Front door storage light 11 comes on when the door is opened.
INTERIOR LIGHTING (3/3) 11 12 Glove box light Boot lights Glove box light 11 comes on when the illumination is turned on. Light 12 comes on when the boot is opened. 3.
PASSENGER COMPARTMENT STORAGE, FITTINGS (1/5) 2 3 1 4 Front door storage pockets 1 Front sun visor They can hold a 1.5-litre bottle. Lower sun visor 2. Centre console storage compartment 4 Courtesy mirrors Lift the cover 3. Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. 3.26 When driving, ensure the courtesy mirror cover is closed. Risk of injury.
PASSENGER COMPARTMENT STORAGE, FITTINGS (2/5) 8 10 9 5 7 6 Cup holders 5 This can be used for storing a mobile ashtray, cup holder, etc. Slide the curtain 6 to open the storage compartment. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of injury if hot liquid escapes. Raise the button 7 to ventilate the storage according to the temperature set by the air conditioner. Lower the button to stop the function.
PASSENGER COMPARTMENT STORAGE, FITTINGS (3/5) 12 13 12 12 11 Glove box Grab handle 12 To open the glove box, lift the catch 11. This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. 3.
PASSENGER COMPARTMENT STORAGE, FITTINGS (4/5) 16 14 15 Coin holder 14 (depending on the vehicle) Sunglasses holder 15 (depending on the vehicle) Front seat storage pockets 16 Push 15 to open the sunglasses holder. 3.
PASSENGER COMPARTMENT STORAGE, FITTINGS (5/5) 17 Rear armrest with cup holder Pull down the armrest 17. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of injury if hot liquid escapes. 3.
ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET 2 3 1 Ashtray location 1 Accessories sockets 3 Cigarette lighter or accessories sockets 2 They are provided for connecting accessories approved by our Technical Department. With the ignition on, push in the cigarette lighter 2 - it will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in.
REAR HEADRESTS A Position for use Lift the headrest to maximum height, then lower it until it locks. To remove a headrest Raise the headrest as far as it will go, then press button A and remove the headrest. To refit a headrest Insert the rods in the holes, press the button A and lower the headrest. Check that it is correctly locked in place. 3.32 Centre seat headrest storage position Press the button A and lower the central headrest 1 completely.
REAR BENCH SEAT (1/3) To replace the seatback, proceed in the reverse order to removal. Refit the seatback and click it back into place. 1 A B When refitting the seatback, make sure it is correctly locked in place. If seat covers are fitted, make sure these do not prevent the seatback latch from locking in. Make sure that the seat belts are positioned correctly. Reposition the headrests. To manually fold down the seatbacks Ensure that the front seats are far enough forward. Lower the headrests fully.
REAR BENCH SEAT (2/3) 2 3 To automatically fold down the seatbacks (flat position) Conditions of use Use restriction – Vehicle stationary; Place seat belt in hook 2 to avoid damaging the belt. From the boot, pulling the control 3 enables you to automatically unlock the rear bench seatbacks to get a flat floor. – tailgate open; It is forbidden to drive with a seatback or a front seat folded down when there is a passenger occupying a rear seat.
REAR BENCH SEAT (3/3) Press the left side of the switch to select the warmest setting or the right side of the switch to select the average setting. The middle position of the switch is off. The indicator light in the switch lights off. 5 4 The system, which has a thermostat, decides whether heating is needed depending on the position selected and stops heating once a certain temperature has been reached.
BOOT 2 3 1 To open Press button 1 and lift the tailgate. To close Lower the tailgate using the handles 2 inside the tailgate to help you. Opening the doors manually from the inside If it is impossible to unlock the tailgate, it can be done manually from inside: – access the luggage compartment by tilting the rear bench seatback(s), – insert a pencil or similar object in recess 3 and slide the unit as shown in the illustration; – push the tailgate to open it. 3.
AUTOMATIC TAILGATE (1/5) If fitted on the vehicle, the tailgate locks and unlocks at the same time as the doors. Depending on the vehicle, you have several different ways to manoeuvre the tailgate: – using the RENAULT card remote control; – using the controls on the tailgate; – using the dashboard control; – using the hands-free function. The attaching of any carrying device (bike rack, luggage box, etc.) resting on the luggage compartment lid is prohibited.
AUTOMATIC TAILGATE (2/5) 3 2 1 Using the RENAULT card remote control Using the tailgate exterior opening control Using the tailgate interior closing control With the ignition off, press and hold switch 1 on the RENAULT card. Press control 2. Press control 3. As a safety precaution, the doors should only be opened or closed when the vehicle is stationary. Risk of injury. 3.
AUTOMATIC TAILGATE (3/5) Activation/deactivation of the hands-free function Using the multifunction screen, select menu “Vehicle”, “User settings” then “Use handsfree card: open/close”. Select “ON” or “OFF” to activate or deactivate the function. Usage features of the hands-free function 4 Using the dashboard control Depending on the vehicle, press and hold switch 4. Using the hands-free function The hands-free function grants access to the boot or allows it to be closed while you have your hands full.
AUTOMATIC TAILGATE (4/5) Stopping the tailgate manoeuvre The automatic tailgate manoeuvre can be stopped at any time by a short press on one of the controls. Depending on the opening position, the tailgate hatch can however continue to be opened manually. If the tailgate is stationary in the intermediate position, your next press will move the tailgate in the opposite direction to when you stopped it.
AUTOMATIC TAILGATE (5/5) Precautions during use Operating faults Before opening/closing the tailgate, ensure that the surrounding space is sufficient to allow the tailgate to operate. If not, stop the tailgate movement with the external tailgate control and hold the tailgate in position by hand (the tailgate may continue to open manually). If you activate the automatic tailgate continuously for around a minute (sequence of opening and closing), it will stop in order to avoid overheating.
LUGGAGE COMPARTMENT COVER Removing/refitting the luggage cover 2 4 1 2 3 Press the two ends 4 to maximum and move them towards the centre of the luggage compartment cover, then tilt the cover. 1 To unfold the luggage compartment cover 2 Pull handle 1 located under the cover and place each end of the cover in the notch 3. To fit the luggage cover, carry out this procedure in reverse.
LUGGAGE NET (1/2) A 1 2 B 3 5 4 6 Depending on the vehicle, this may be used when transporting animals or luggage to isolate them from the passenger section. Fitting the luggage net behind the front seats It can be positioned: – lift the cover 1 to access the anchoring point; – A: behind the rear seats; – B: behind the front seats. The luggage net is designed to retain a maximum weight of 10 kg. Risk of injury.
LUGGAGE NET (2/2) 8 7 7 9 11 Fitting the luggage net behind the rear seats – latch the hook 10 to the anchoring point 11; Inside the vehicle on each side: – adjust the net strap 9 so that it is taut. The seatbacks must not touch the luggage net; – lift the cover 7 to access the anchoring point; – latch the hook 8 of luggage net to the anchoring point; 3.44 – fit the luggage net in the same way for the other side.
BOOT FITTINGS 1 2 3 Bag hooks 1 Anchorage points Maximum weight per hook: 3kg. Attachment points 2. If your vehicle is not equipped with anchorage points, you can get them from an authorised dealer. Maximum weight on trunk board 3 is 60kg. 3.
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). A 1 – The front seatbacks with the rear seatbacks folded down, the mobile floor in the flat-floor position (example B). – The front seatbacks with the rear seatbacks folded down, the mobile floor in the stored-away position, as is the case for maximum loads (example C).
TRANSPORTING OBJECTS towbar A Maximum dimension A: 1115 mm. Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. Choice and fitting of towing equipment Maximum weight of towing equipment: 37 kg For fitting and conditions of use, refer to the equipment’s fitting instructions. Please keep these instructions with the rest of the vehicle documentation.
ROOF BARS, SPOILER 1 2 Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the operation of the tailgate. Accessing the mounting points Vehicles fitted with longitudinal roof bars The attachment inserts 2 are located on the longitudinal roof bars 1.
MULTIMEDIA EQUIPMENT (1/2) 1 4 3 2 Multimedia systems 1 2 3 4 Multimedia touchscreen; Steering column controls; Steering wheel controls; Microphone. Hands-free telephone integrated control For equipped vehicles, use the steering wheel controls 3. Using the telephone Refer to the equipment instructions for information on how to operate this equipment. We remind you of the need to conform to the legislation in force concerning the use of such equipment. 3.
MULTIMEDIA EQUIPMENT (2/2) Multimedia sockets 6 Sockets USB can only recharge accessories with a maximum power rating of 10.5 Watts (voltage: 5V) per socket, which have been approved by our Technical Department. 5 Multimedia sockets 5 You can use sockets USB or the SD card reader to access the multimedia content of your accessories and the system update (please refer to the equipment instructions). The various sources can be selected from the multifunction screen and from the steering column controls. 3.
Section 4: Maintenance Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: topping up, filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil change . . . . . . . . . . . . . . . . . . . . . .
BONNET (1/2) 3 Do not press down on the bonnet: there is a risk that the bonnet may accidentally close. 1 2 To open, pull handle 1. Unlocking the bonnet catch To unlock, push tab 2 at the same time as opening the bonnet. Opening the bonnet Before performing any action in the engine compartment, the ignition must be switched off by pressing the engine stop button (please see the information on “Starting, stopping the engine” in Section 2). 4.
BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight. Ensure that the bonnet is properly locked. Check that nothing is preventing the catch from locking (gravel, cloth, etc.).
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
ENGINE OIL LEVEL: topping up, filling (1/2) 1 2 2 1 Topping up/filling – Unscrew cap 1; The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). – top up the level (as a guide, the capacity between the minimum and maximum reading on the dipstick 2 is between 1.
ENGINE OIL LEVEL: topping up, filling (2/2) 1 2 Do not exceed the max level and do not forget to refit cap 1 and dipstick 2. 4.6 1 2 In order to prevent splashback, it is recommended that a funnel be used when topping up/filling with oil.
ENGINE OIL LEVEL: OIL CHANGE Oil change Engine oil grade Service interval: refer to the Maintenance Document for your vehicle. Refer to the maintenance document for your vehicle. Oil change capacity Please refer to the maintenance document for your vehicle, or contact an authorised dealer. Always check the engine oil level using the dipstick, as explained previously (it should never fall below the minimum level, or be over the maximum level on the dipstick).
LEVELS (1/3) 1 Frequency of checking coolant level Replacement interval Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). Refer to the Maintenance Document for your vehicle. If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – an anti-corrosion protection for the cooling system.
LEVELS (2/3) Level 2 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI” warning line. 2 If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from the manufacturer’s network or web site. Topping up Brake fluid level The level should be read with the engine switched off and on level ground.
LEVELS (3/3)/FILTERS Filters The replacement of filter components (air filter, cabin filter, diesel filter, etc.) is scheduled in the maintenance operations for your vehicle. 4 3 Windscreen washer reservoir Topping up With the engine switched off, open the cap 3. Fill until you can see the fluid, then replace the cap. Liquid Screen wash product (product with antifreeze in winter). When working in the engine compartment, ensure that the windscreen wiper stalk is in the park position. Risk of injury. 4.
TYRE PRESSURE (1/2) E: front tyre pressure. F: rear tyre pressure. A G: tyre pressure for the emergency spare wheel. B A C C D E E E F F F G Label A Open the driver’s door to read it. Tyre pressures should be checked when the tyres are cold. If the tyre pressures cannot be checked when the tyres are cold, increase the pressures from 0.2 to 0.3 bar (or 3 PSI). Never deflate a hot tyre. Vehicle fitted with a tyre pressure monitoring system In cases of under-inflation (puncture, low pressure, etc.
TYRE PRESSURE (2/2) Special note concerning fully laden vehicles (Maximum Permissible All-Up Weight) and towing a trailer: the maximum speed must be limited to 60 mph (100 kph) and the tyre pressure increased by 0.2 bar. Please refer to the information on “Weights” in Section 6. Tyre safety and use of snow chains: Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains. For your safety, please respect the speed limit.
BATTERY (1/2) 1 Depending on the vehicle, a system continuously checks the battery charge status. If this decreases, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. The message will go off. The charge status of your battery can decrease especially if you use your vehicle: – for short journeys; – for driving in town; – when the temperature drops; Battery 1 does not require any maintenance. You should not open it or add any fluid.
BATTERY (2/2) Replacing the battery A 2 7 3 4 6 5 As this operation is complex, we advise you to contact an approved Dealer. Label A Observe the indications on the battery: – 2 Naked flames and smoking are forbidden; – 3 eye protection required; – 4 keep away from children; – 5 explosive materials; – 6 refer to the handbook; – 7 corrosive materials. dealer. 4.14 The battery is a specific type, please ensure it is replaced with the same type.
BODYWORK MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Your vehicle has been treated with very effective anti-corrosion products. It is nevertheless subject to various outside influences. Corrosive agents in the atmosphere – atmospheric pollution (built-up and industrial areas), – saline atmospheres (near the sea, particularly in hot weather), – seasonal and damp weather conditions (e.g.
BODYWORK MAINTENANCE (2/2) Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway). Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. Remember to visit the body shop periodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Document.
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. Glass instrument panel A stain should always be dealt with swiftly. Use a soft cloth (or cotton wool). If this does not clean them properly, use a soft cloth (or cotton wool) slightly moistened with soapy water and then wipe clean with another soft damp cloth or cotton wool. Finally, carefully dry off with a soft dry cloth.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
Section 5: Practical advice Puncture, emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing a wheel . . . . . . . . . . . . . . . . .
PUNCTURE, EMERGENCY SPARE WHEEL (1/2) In case of puncture Depending on the vehicle, a tyre inflation kit or emergency spare wheel is provided (refer to the following pages). Special note The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emergency spare wheel disappears from the instrument panel display). Refer to the information on the “Tyre pressure monitoring system” in Section 2.
PUNCTURE, EMERGENCY SPARE WHEEL (2/2) 1 Note: Store the punctured wheel in the storage bag provided, along with the tool kit and put them in the boot. A Emergency spare wheel A To get to it: – open the tailgate; – remove the mobile floor 1; – remove the tool kit box by lifting it by its handles; – unscrew the central mounting; – if the vehicle is fitted with amplifier, place it to the side; Note: be careful not to impact the amplifier or cut its circuit; – remove the emergency spare wheel.
TYRE PRESSURE KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE PRESSURE KIT (2/3) 2 1 With the engine running and the parking brake applied, 3 – Unscrew the cap from recess 3 on the bottle; 4 – unscrew the bottle cap 2; – screw the bottle 2 onto the compressor at the bottle recess point 3; 6 – unscrew the valve cap on the relevant wheel and screw the inflation adapter 6 onto the valve; 5 In the event of a puncture, use the kit located in the boot, underneath the trunk carpet.
TYRE PRESSURE KIT (3/3) – Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; 6 – Put the kit away. – At the end of this initial inflation operation, air will still escape from the tyre. You must drive a short distance in order to seal the hole. – Start immediately and drive at between 12 and 40 mph (20 and 60 km/h) in order to distribute the product evenly in the tyre and, after driving for 2 miles (3 km), stop and check the pressure.
TOOLS Jack 2 2 Fold it correctly before refitting it in its housing. 1 Jack handle 3 This tightens or releases the tow eye 4 Tow eye 4 3 Please see “Towing: breakdown recovery” in Section 5. 4 The presence of the tools depends on the vehicle. The tools are located in a tray under the trunk carpet. Lift the trunk carpet and remove it. Wheelbrace 1 Locks or unlocks the wheel bolts and tow eye 4. Do not leave the tools unsecured inside the vehicle as they may come loose under braking.
CHANGING A WHEEL (1/2) Attach the wheelbrace 1 and the jack handle 6 (in groove 5). 2 Turn the wheelbrace until the wheel lifts off the ground. 3 1 4 5 6 1 Vehicles equipped with a jack, wheelbrace and jack handle Switch on the hazard warning lights. Keep the vehicle away from traffic and on a level surface where it will not slip. Apply the parking brake and engage a gear (first or reverse, or P for automatic transmissions).
CHANGING A WHEEL (2/2) Turn it a few times to lift the wheel off the ground. Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub. Tighten the bolts, checking that the wheel is correctly positioned on its hub. Lower the jack. With the wheel on the ground, tighten the bolts fully and have the tightness of the bolts checked and the emergency spare wheel pressure checked as soon as possible.
TYRES (1/3) The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. You must make sure that your tyres conform to local road traffic regulations. 2 1 For your safety, please respect the speed limit. When they need to be replaced, only tyres of the same make, size, type and profile should be used on a single axle.
TYRES (2/3) Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label affixed to the edge of the driver’s door). The pressures should be checked cold: ignore higher pressures which may be reached in hot weather or following a high speed journey.
TYRES (3/3) Fitting new tyres For safety reasons, this operation must be carried out by a specialist. Fitting different tyres may change your vehicle as follows: – it may mean that your vehicle no longer conforms to current regulations; – it may change the way it handles when cornering; – it may cause the steering to be heavy; – It may affect the use of snow chains. Use in winter Studded tyres Chains This type of equipment may only be used for a limited period and as laid down by local legislation.
FRONT HEADLIGHTS: changing bulbs (1/3) After replacing the bulbs, you must put the air duct A back into position. To do this, perform the above operation in reverse. 1 2 4 A 3 Accessing the bulbs On the left-hand side of the vehicle, you will need to remove the air duct A to access the bulbs. To do this: – remove the clips 3; – unscrew the bolt 2; – press the upper part of the fastening clips 1 to release the air duct A; – slide the air duct A towards the front of the vehicle to release it.
FRONT HEADLIGHTS: changing bulbs (2/3) 5 6 It is essential to use anti-U.V. 55W bulbs so as not to damage the plastic on the headlights. Do not touch the bulb glass. Hold it by its base. B C 8 7 Halogen dipped beam headlight To change the bulb: To change the bulb: – remove cover C; – remove cover B; – remove the clip 7 pressing down on it; – remove the clip 5 pressing down on it; Halogen main beam headlight – remove the connector 8; – remove the connector 6 – replace the bulb.
FRONT HEADLIGHTS: changing bulbs (3/3) 9 Front fog lights 11 Additional lights The front bumper needs to be removed; consult an approved Dealer. If you wish to fit fog lights to your vehicle, please see an authorised dealer. Bulb type: H11. 9 10 LED front fog lights 11 Please see an authorised dealer. 12 11 LED Direction indicator light 12 Please see an authorised dealer. LED dipped beam/main beam headlights 10 Please see an authorised dealer.
REAR AND SIDE LIGHTS: changing bulbs (1/3) 2 1 Side lights and brake lights 1 Direction indicators 2 Consult an approved Dealer. Consult an approved Dealer. 5.
REAR AND SIDE LIGHTS: changing bulbs (2/3) 4 3 Reversing lights Open the tailgate. Unclip the trim 3 and remove it. Turn bulb holder 4 fully anticlockwise and change the bulb. Refitting To refit, proceed in the reverse order, taking care not to damage the wiring. Bulb type: W16W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
REAR AND SIDE LIGHTS: changing bulbs (3/3) 5 7 8 6 High level brake light 5 Consult an approved dealer. Rear fog lights 6 Consult an approved dealer. Halogen number plate lights 7 Side indicator lights 8 Consult an authorised dealer. – Unclip the light 7 (using a tool such as a flat-blade screwdriver). – remove the light cover to gain access to the bulb. Bulb type: W5W. LED number plate light 7 Consult an approved dealer. The bulbs are under pressure and can break when replaced. Risk of injury.
INTERIOR LIGHTING: changing bulbs (1/2) 5 1 2 3 Map reading lights 1 Ambient lights 2 Glove box lights 3 Please consult an authorised dealer. Please consult an authorised dealer. Please consult an authorised dealer. 1 The bulbs are under pressure and can break when replaced. Risk of injury. 5.
INTERIOR LIGHTING: changing bulbs (2/2) 8 5 7 6 4 Front door lights 4, door ambient light 5, door storage light 6 Please consult an authorised dealer. Boot lights 7 Unclip light 7 by pressing the tabs on each side (using a flat-blade screwdriver or similar). Disconnect the light. Press tab 8 to release the lens 10 and access bulb 9. Bulb type: W5W. Front foot lights 11 The bulbs are under pressure and can break when replaced. Please consult an authorised dealer. Risk of injury. 11 5.
RENAULT CARD: battery 1 A 2 Replacing the battery When the message “Keycard battery low” appears on the instrument panel, replace the battery in the RENAULT card: – slide the rear casing 1 downwards while pressing on zone A; – remove the battery cover 2; – remove the battery by pressing on one side and lifting the other; – replace it according to the direction and template shown inside the cover.
RADIO FREQUENCY REMOTE CONTROL: batteries 1 1 Replacing the battery Open the case at slot 1 using a flatblade screwdriver or similar, and replace the battery 2, observing the polarity shown on the back of the cover. 2 Note: It is not advisable to touch the electronic circuit in the key cover when replacing the battery. The batteries are available from approved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect electrical contact. 5.
FUSES (1/3) Fuses in passenger compartment A on the right-hand side of the vehicle Glove box needs to be disassembled to access the fuses. Please consult an authorised dealer. A B If any electrical component does not work, check the condition of the fuses. Fuses in passenger compartment A on the left-hand side of the vehicle Fuses in passenger compartment B on the vehicle with stop and start function Unclip the cover B using a screwdriver or similar. Unclip the cover A using a screwdriver or similar.
FUSES (2/3) Use the fuse allocation label in the storage compartment A or B to identify the fuses. Certain fuses should only be replaced by a qualified professional. These fuses are not listed on the label. 1 Only change the fuses represented on the label. Clip 1 Check the fuse in question and replace it, if necessary, by a fuse of the same rating. Remove the fuse using tweezers 1, located on the fuse plate. To remove the fuse from the tweezers, slide the fuse to the side.
FUSES (3/3) Allocation of fuses (the presence of certain fuses depends on the vehicle equipment level) Symbol Allocation BLOWER Ventilation TURN HAZARD Hazard lamp 2ND POWER SOCKET 2nd power socket REAR WIPER POWER DR LOCK Rear wiper Power door lock ELEC B, B2 Electrical equipment IMOB AUDIO Immobilizer Symbol VDC Allocation Vehicle dynamic control STOP LAMP Stop lamp POWER Power door lock DR LOCK2 Symbol Allocation H/MIRR Heated door mirrors HEATER SEAT Heater seat EC AUTO ACC Air con
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (courtesy lights, etc.) are switched off before disconnecting or reconnecting the battery; The battery charger must be compatible with a battery with nominal voltage of 12 volts. – when charging, stop the charger before connecting or disconnecting the battery; Do not disconnect the battery when the engine is running.
BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle The two batteries must have an identical nominal voltage of 12 volts. The battery supplying the current should have a capacity (amp-hours, Ah) which is at least the same as that of the discharged battery. Ensure that there is no risk of contact between the two vehicles (risk of short circuiting when the positive terminals are connected) and that the discharged battery is properly connected.
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 Watts only. Fire hazard. When several accessory sockets are used at the same time, the total power of the connected accessories must not exceed 180 watts.
WINDSCREEN WIPER BLADES: replacement (1/2) Refitting 1 3 2 Windscreen wiper blades 1 With the ignition on and the engine switched off, lower the windscreen wiper stalk fully: the blades stop slightly away from the bonnet. Slide the blade along the arm until it clips on. Check that it is correctly locked in place. Lower the windscreen wiper arm carefully. With the ignition on, return the windscreen wiper stalk to the stop position. The blade on the driver’s side must always be above the passenger blade.
WINDSCREEN WIPER BLADES: replacement (2/2) To refit A To refit the wiper blade, proceed in reverse order to removal. Make sure that the blade is correctly locked in position. 4 B 5 6 Rear screen wiper blade 4 Stalk in stop position (deactivated): – Lift the wiper arm 6; – pivot wiper blade 4 until some resistance is met (movement B); – depending on the vehicle, press tab 5, then remove the wiper blade by pulling it (movement A). Keep monitoring the condition of the wiper blades.
TOWING: breakdown recovery (1/4) Before towing, put the gearbox in neutral, unlock the steering column and release the parking brake. For vehicles fitted with an automatic gearbox, if it is not possible to put the gear lever into position N, please consult an authorised dealer. Steering column unlocking Insert the key into the ignition or, depending on the vehicle, having the RENAULT card on you, press the engine start button for approximately 2 seconds.
TOWING: breakdown recovery (2/4) 2 1 2WD vehicles Vehicles fitted with an automatic transmission or continuously variable transmission. With the ignition off, the gearbox is no longer lubricated. If it is not, the vehicle must be transported on a trailer or be towed with the front wheels off the ground. 5.32 When setting off, if the lever is locked in position P even though you are pressing the brake pedal, the lever can be released manually.
TOWING: breakdown recovery (3/4) 4WD vehicles Whichever type of gearbox is fitted, a 4WD vehicle must never be towed if any of its 4 wheels are touching the ground. A 4WD vehicle must never be towed if one of its 4 wheels is touching the ground. 5.
TOWING: breakdown recovery (4/4) Do not leave the tools unsecured inside the vehicle as they may come loose under braking. A 3 5 4 Only use the front towing point A and the rear towing point 5 (never use the driveshafts). These towing points may only be used for towing: never use them for lifting the vehicle directly or indirectly. When the engine is stopped, steering and braking assistance are not operational. 5.34 Access to towing points – Use a rigid towing bar.
OPERATING FAULTS (1/7) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or unlock the doors. Card battery is flat. Replace the battery.
OPERATING FAULTS (2/7) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the remote control POSSIBLE CAUSES The remote control does not lock or The remote control battery is flat. unlock the doors. ACTION REQUIRED Use the emergency key. Use of appliances operating on the same Stop using the devices or use the key. frequency as the remote control (mobile phone, etc.).
OPERATING FAULTS (3/7) The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights are weak or fail to light up and the starter does not turn. Battery terminals not tight, battery terminals disconnected or oxidised. Retighten or reconnect the terminals, or clean them if they are oxidised. Discharged battery or not operational. Connect another battery to the faulty battery.
OPERATING FAULTS (4/7) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pressures, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved Dealer. White smoke from the exhaust. In the diesel version, this is necessarily a fault. Smoke may be caused by particle filter regeneration. Please refer to the information on “Special features of diesel versions” in Section 2. Smoke under the bonnet.
OPERATING FAULTS (5/7) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The coolant temperature indicator is in the warning zone and warning light ® comes on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an approved dealer as soon as possible.
OPERATING FAULTS (6/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Blown bulb.
OPERATING FAULTS (7/7) Electrical equipment POSSIBLE CAUSES Traces of condensation in the lights. Traces of condensation may be a natural phenomenon caused by variations in temperature. WHAT TO DO In this case, the traces will disappear slowly once the lights are switched on. The front seat belt reminder light comes on when the seat belts are fastened. An object is stuck between the floor and the seat and is disrupting the operation of the sensor. Remove all objects from underneath the front seats.
5.
Section 6: Technical specifications Vehicle identification plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine identification plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications . . . . . . . . . . .
VEHICLE IDENTIFICATION PLATES A A 10 9 1 2 3 4 5 6 7 8 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. The presence and location of the information depends on the vehicle. B 6.2 Vehicle identification plate A 1 Manufacturer name. 2 EC design number or approval number. 3 Identification number. Depending on the vehicle, this information is also given on marking B. 4 MAM (Maximum Authorised Mass).
ENGINE IDENTIFICATION PLATES A 1 2 3 A A Please quote the information on the engine plate or label A in all correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. A A 6.
DIMENSIONS (in metres) 0,929 2,705 1,038 1,597 4,672 1,678* 1,592 2,063 * Unladen, with or without longitudinal roof bar 6.
ENGINE SPECIFICATIONS Versions 2.0 GDi 2.5 16V 2.0 dCi 1.6 dCi Engine type (see engine plate) M5R QR25 M9R Turbo R9M Cubic capacity (cc) 1 997 2 488 1 995 1 598 Type of fuel Octane rating It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap. Diesel The label located in the fuel filler flap indicates the authorised fuels. Spark plugs Only use the spark plugs specified for your vehicle’s engine.
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer.
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
SERVICE SHEETS (1/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (2/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (3/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (4/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (5/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (6/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ALPHABETICAL INDEX (1/5) A ABS ..............................................................1.56, 2.31 → 2.34 accessories........................................................................ 5.28 accessories socket ............................................................ 3.31 adaptive cruise control...........................................2.66 → 2.73 additional methods of restraint .......................................... 1.33 side protection .....................................................
ALPHABETICAL INDEX (2/5) windscreen ...........................................................3.4 → 3.6 dimensions .......................................................................... 6.4 dipstick................................................................................. 4.4 display ...................................................................1.54 → 1.61 doors/tailgate ...........................................................1.4 → 1.16 driver assistance.............................. 2.
ALPHABETICAL INDEX (3/5) heated seats ............................................................. 1.20, 1.22 heating and air conditioning system .................3.4 → 3.6, 3.17 heating system ........................................................3.4 → 3.17 Hill Start Assist.......................................................2.31 → 2.34 horn ................................................................................... 1.84 horn: flash ............................................................
ALPHABETICAL INDEX (4/5) O oil change ..................................................................4.5 → 4.7 opening the doors ..................................................1.11 → 1.15 operating faults ................................ 1.54 → 1.59, 5.35 → 5.41 overspeed warning ................................................2.56 → 2.58 P paintwork maintenance ..................................................... 4.15 – 4.16 parking assistance: assisted parking .....................2.81 → 2.
ALPHABETICAL INDEX (5/5) coolant ........................................................................... 4.8 tanks and reservoirs: windscreen washer ...................................................... 4.10 technical specifications ..............................................6.4 → 6.7 telephone ................................................................ 3.49 – 3.50 temperature regulation ............................................3.7 → 3.17 tool kit ............................................
7.
RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
