ESPACE DRIVER’S HANDBOOK
A passion for performance ELF, partner of RENAULT recommends ELF Partners in cutting-edge automotive technology, Elf and Renault combine their expertise on both the racetrack and the city streets. This enduring partnership gives drivers a range of lubricants perfectly suited to Renault cars. Lasting protection and optimum performance for your engine – guaranteed.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections Getting to know your vehicle ............................... 1 Driving 2 ................................................................... Your comfort ......................................................... 3 Maintenance ......................................................... 4 Practical advice .................................................... ...................................... 6 ...............................................
0.
Section 1: Getting to know your vehicle The RENAULT card: general information and use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 Locking/unlocking the doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.8 Opening and closing the doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.11 Automatic locking when driving . . . . . . . . . . . . . . . .
RENAULT CARD: general information (1/2) 1 4 2 3 The RENAULT card is used for: RENAULT card operating range – locking/unlocking the doors and tailgate (doors, tailgate) and the fuel filler flap (see the following pages); – switching on the vehicle lighting remotely (refer to the following pages); – Automatic closing of electric windows and, depending on the vehicle, of the sunroof; please see the information on “Electric windows” and “Electric sunroof” in Chapter 3; – starting the engine; please see the
RENAULT CARD: general information (2/2) 4 Advice Avoid leaving the card in hot, cold or humid areas. Do not keep the RENAULT card in a place where it could be bent or damaged accidentally, such as in a back pocket of a garment. Distance lighting function Pressing button 4 switches on the dipped beam headlights, the indicator lights and the interior lighting for approximately 30 seconds. This can be used, for example, to identify the vehicle from a distance when parked in a car park.
RENAULT “HANDS-FREE” CARD: usage (1/4) There are two ways to unlock/lock the vehicle: – the RENAULT card in “Hands-free” mode; – the RENAULT card in remote control mode. Driver’s responsibility Never leave an animal, child or adult who is not self-sufficient alone in your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or locking the doors, for example.
RENAULT “HANDS-FREE” CARD: usage (2/4) “Hands-free” locking using the sensor 3 If you wish to lock your vehicle while the card is within range, make sure that the doors and boot are closed and place your finger over the sensor 3 on the driver’s door handle. The vehicle will lock. 2 Note: The sensor cannot be used to lock the vehicle unless the RENAULT card is within the access zone 1.
RENAULT “HANDS-FREE” CARD: usage (3/4) 5 6 7 3 Particular features of the locking system (continued) If the RENAULT card has been within range for approximately 15 minutes, remote locking is disabled. The vehicle cannot be locked if the card is within the zone 7. If the vehicle is unlocked by pressing the button on the RENAULT card, but the doors or boot are not then opened; remote “hands-free” locking is disabled. Using the card as a remote control Unlocking with the card RENAULT Press the button 5.
RENAULT “HANDS-FREE” CARD: usage (4/4) 7 8 Driver’s responsibility Never leave an animal, child or adult who is not self-sufficient alone in your vehicle, even for a short time. If, while the engine is running, a door is opened and closed, and the card is no longer in the zone 7, the message Keycard not detected indicates that the card is not inside the vehicle. This will, for example, prevent you from driving away after dropping off a passenger who has kept the card on them.
LOCKING, UNLOCKING THE DOORS (1/3) If the RENAULT card does not work: In certain cases, the RENAULT card may not work: 2 1 A – when the RENAULT card battery is drained, flat battery, etc. – use of appliances operating on the same frequency as the card (mobile phone, etc.); – vehicle located in a high electromagnetic radiation zone.
LOCKING, UNLOCKING THE DOORS (2/3) 4 B 3 2 Using the key integrated in the RENAULT card – Insert the tip of the key 2 into the notch 3 at the bottom of the cover A on the front left-hand door; – Move it upwards to remove the cover B; – Insert the key 2 into the lock and lock or unlock the front left-hand door. Locking the doors manually Turn screw 4 with the door open (using the end of the key) and close the door. This means that the doors are then locked from the outside.
LOCKING, UNLOCKING THE DOORS (3/3) 5 Interior locking/unlocking door control Switch 5 controls the doors, the boot and the fuel filler flap simultaneously. If a door or the tailgate is open or not closed properly, the doors and tailgate lock/unlock quickly. If you need to carry a load with the boot open, you can still lock everything else: with the engine stopped, press switch 5 for more than five seconds to lock the other opening elements. 1.
OPENING AND CLOSING THE DOORS (1/3) Lights-on reminder buzzer 2 If you have switched off the ignition and left the lights switched on, a reminder buzzer will sound when a door is opened while the light stalk is not in position AUTO. 1 Opening the doors from the outside Opening from the inside Pull on the handle 2. With the doors unlocked or RENAULT card on you, hold handle 1 and pull it towards you. As a safety precaution, the doors should only be opened or closed when the vehicle is stationary. 1.
OPENING AND CLOSING THE DOORS (2/3) 4 3 Door/tailgate open buzzer At a standstill, warning light 3 lights up on the instrument panel alongside warning light 4, indicating the opening element(s) (door, boot) open or incorrectly closed. 1.
OPENING AND CLOSING THE DOORS (3/3) As a safety precaution, the doors should only be opened or closed when the vehicle is stationary. 5 Child safety Press switch 5 to allow or prevent opening of the rear doors and rear electric windows from inside the vehicle. The indicator light in the switch lights up to confirm that the locks have been activated. Note: If there is a system fault, the message “Check child safety device” is displayed on the instrument panel: please contact an authorised dealer.
AUTOMATIC LOCKING WHEN DRIVING Activating/deactivating the function 1 2 To switch it on: with the vehicle at a standstill and the engine running, press switch 2 until a beep sounds. To deactivate: with the vehicle at a standstill and the engine running, press switch 2 until two beeps sound. You can also deactivate/activate the function from the menu on the multifunction screen 1 (refer to the information on the “Vehicle settings customisation menu” section 1, “Auto door locking while driving” function).
AUTOMATIC TAILGATE (1/5) If fitted on the vehicle, the tailgate locks and unlocks at the same time as the doors. There are four modes to manoeuvre the tailgate: – using the RENAULT card remote control; – using the controls on the tailgate; – using the dashboard control; – using the hands-free function. Conditions of use Opening/Closing – Immobilise the vehicle.
AUTOMATIC TAILGATE (2/5) 3 2 1 Using the Renault card remote control Using the tailgate exterior opening control Using the tailgate interior closing control With the ignition off, press and hold switch 1 on the RENAULT card. Press control 2. Press control 3. As a safety precaution, the doors should only be opened or closed when the vehicle is stationary. Risk of injury. 1.
AUTOMATIC TAILGATE (3/5) Activation/deactivation of the hands-free function 5 Using the multifunction screen, select menu “Vehicle”, “User settings” then “Use handsfree card: open/close”. Select “ON” or “OFF” to activate or deactivate the function. Usage features of the hands-free function 4 Using the dashboard control Press and hold switch 4. Do not keep your foot in the air. Carry out the movement without stopping.
AUTOMATIC TAILGATE (4/5) Stopping the tailgate manoeuvre Automatic reversal of the tailgate manoeuvre The automatic tailgate manoeuvre can be stopped at any time by a short press on one of the controls. If the tailgate encounters an obstacle (presence of an object or a person) during its manoeuvre, it will stop and reverse its direction by a few degrees in order to release the obstacle.
AUTOMATIC TAILGATE (5/5) Precautions during use Operating faults Before opening/closing the tailgate, ensure that the surrounding space is sufficient to allow the tailgate to operate. If not, stop the tailgate movement before contact. If you activate the automatic tailgate continuously for around a minute (sequence of opening and closing), it will stop in order to avoid overheating. The operation will return to normal after about a minute.
FRONT HEADRESTS To adjust side supports B Depending on the vehicle, sections B can be adjusted independently to the desired position. A B 1 B 3 2 To remove the headrest Raise it to its highest position (tilt the seatback backwards if necessary). Press button 2 and lift the headrest to release it. To refit the headrest To raise the headrest Pull the headrest upwards to the desired height. To lower the headrest Press button 2 and guide the headrest down to the desired height.
FRONT SEATS WITH MANUAL CONTROL (1/2) To tilt the seatback Lift handle 3 and tilt the seatback to the desired position. Release the handle at the desired position and make sure that it is locked. 2 1 3 4 To move the seat forwards or back To adjust the seat’s lumbar position Lift handle 1 to release. Release the handle at the desired position and make sure that it is locked. Lower handle 4 to increase the support and lift it to decrease it.
FRONT SEATS WITH MANUAL CONTROL (2/2) Operating faults When an operating fault is detected, the integrated warning lights on the switch 5 for the seat concerned flash. Consult an approved dealer. 5 Heated seats With the ignition on: – Pressing the switch 5 on the required seat for the first time activates the heating system on high. Both integrated switch warning lights come on; – pressing the switch for the second time changes the heating to low.
DRIVER’S SEAT WITH ELECTRIC CONTROLS (1/2) Adjusting the seatback To tilt the seatback, move the top of switch 2 forwards or backwards. Adjusting the lumbar support on the driver’s seat 1 2 3 Move the switch 3 forwards, backwards, up or down. For safety reasons, carry out any adjustments when the vehicle is not being driven. On equipped vehicles, switch 1 grants access to the seats menu on the multifunction screen (please refer to the following pages).
DRIVER’S SEAT WITH ELECTRIC CONTROLS (2/2) Adjusting the seat length Lift handle 5 to unlock. Release the handle at the desired position and make sure that it is locked. 4 6 5 Adjusting the seat position Heated seats To move the seat forwards or back Move switch 4 forwards or backwards. With the ignition on: To raise or lower the seat base Move the back of switch 4 up or down. To tilt the seat base (depending on the vehicle) Move the front of switch 4 upwards or downwards.
FRONT SEATS: Functions (1/3) Browse menu “Driver” or “Passenger” to: Massage Driver Massage Passenger – select the type of massage (Tonic, Relaxing or Lumbar); ON – adjust the intensity (+ or -); 1 Tonic – adjust the speed (+ or -); Relaxing Lumbar Intensity – reset the selected settings. Press 2 then “Reset”; Speed – activate/deactivate the massage seat (ON or OFF). 2 Using the multifunction screen, depending on the vehicle you can access a number of seat functions.
FRONT SEATS: Functions (2/3) Easy driver and passenger access Easy access driver ON Easy access passenger ON Courtesy for passenger Press “ON” or “OFF” to activate or deactivate this function. When this function is activated, the seat automatically moves back when the driver or passenger leaves the vehicle, and returns to its position when the start button is pressed.
FRONT SEATS: Functions (3/3) Position Position It is possible to store the driving position of the driver seat. Visual feedback ON 3 The driving position includes the settings for the seat base and seatback as well as the door mirrors. The driving position can be stored and recalled by pressing the buttons: – RENAULT hands-free card detected; – when the driver’s door is opened.
SEAT BELTS (1/3) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. Adjusting your driving position Make sure that the rear seats are locked in position properly so that the rear seat belts will operate efficiently.
SEAT BELTS (2/3) Driver’s seat belt reminder and, depending on the vehicle, front passenger seat belt reminder This lights up on the interior rear-view mirror when starting the engine then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approximately 12 mph (20 km/h), it flashes and a bleep sounds for around 120 seconds. Note: an object placed on the passenger seat base may activate the warning light in some cases.
SEAT BELTS (3/3) 7 – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats) contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident. – Never wear the shoulder strap under your arm or behind your back.
REAR SEAT BELTS 4 A B 10 5 1 2 11 9 6 12 8 3 Second row rear side seats 7 Second row centre rear seat Slowly unwind belt 1. Unwind belt 5 slowly from its housing 4. Click the sliding buckle 2 into the corresponding red catch 3. Click buckle 9 into black catch 8. Slowly unwind the strap 10. Snap the last sliding buckle 6 into the red catch 7. Click the buckle 11 into the corresponding black catch 12.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are composed of: – seat belt inertia reel pretensioners; – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. airbags for driver and passenger Fitted to the driver and passenger side. The presence of this equipment is indicated by the word “Air bag” on the steering wheel and dashboard (air bag zone A) and, depending on the vehicle, a symbol on the lower section of the windscreen.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operating faults å This warning light comes on when the engine is started and then goes out after approximately three seconds. If it does not come on when the ignition is switched on or if it stays on, there is a fault in the system. Contact your approved Dealer as soon as possible. Your protection will be reduced until this fault is rectified. Operation This system is only operational when the ignition is switched on.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
METHODS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (air bags, electronic control units, wiring) and the system components must not be reused on any other vehicle, even if identical.
SIDE PROTECTION DEVICES Side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Curtain air bags These are air bags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear side windows to protect the passengers in case of a severe side impact.
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. The airbag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
CHILD SAFETY: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
CHILD SAFETY: choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position for as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. Forward-facing child seats The child’s head and abdomen need to be protected as a priority.
CHILD SAFETY: choosing a child seat mounting (1/3) There are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
CHILD SAFETY: choosing a child seat mounting (2/3) Attachment using the ISOFIX system Approved child seats ISOFIX are standardised in accordance with current regulations if any of the four cases below applies: Attach the child seat with the ISOFIX locks, if these are provided. The ISOFIX system allows quick, easy, safe fitting. The ISOFIX system consists of 2 rings and, in some cases, a third ring.
CHILD SAFETY: choosing a child seat mounting (3/3) The rings are located on the rear seatbacks and indicated by the symbol . 1 3 4 5 Pull the belt so that the back of the child seat comes into contact with the back of the vehicle seat. 2 Attachment using the ISOFIX system (continued) The two rings 1 are located between the seatback and the seat base of the seat and are identified by a marking.
CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seat indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. In the front seat Fit the child seat in a rear seat wherever possible. Make sure that the child seat or the child’s feet do not prevent the front seat from locking correctly.
CHILD SAFETY: fitting a child seat, general information (2/2) In the rear seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest the door. For 7-seater vehicles, the second row rear seats must be pushed forward before a child is seated in the third row rear seats.
CHILD SEATS: attachment by seat belt (1/6) Visual installation of the five-seater version ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. ² Seat not suitable for fitting child seats. Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt.
CHILD SEATS: attachment by seat belt (2/6) The table below summarises the information already shown on the diagram on the previous page, to ensure the applicable regulations are respected.
CHILD SEATS: attachment by seat belt (3/6) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest the door. (3) If necessary, position the vehicle seat as far back as possible.
CHILD SEATS: attachment by seat belt (4/6) The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected.
CHILD SEATS: attachment by seat belt (5/6) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest the door. (3) If necessary, position the vehicle seat as far back as possible.
CHILD SEATS: attachment by seat belt (6/6) Installation diagram, 7-seater version ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. ² Seat not suitable for fitting child seats. Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt.
CHILD SEATS: attachment using the ISOFIX system (1/6) Visual installation of the five-seater version Child seat fitted using the ISOFIX mounting ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached. The anchorage points are located on the backs of the rear seats.
CHILD SEATS: attachment using the ISOFIX system (2/6) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
CHILD SEATS: attachment using the ISOFIX system (3/6) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted. i-U = Suitable for the i-Size restraint devices in the “universal” forward-facing and backward-facing category. (1) If necessary, position the vehicle seat as far back as possible.
CHILD SEATS: attachment using the isofix system (4/6) The table below summarises the information already shown in the diagram on the following pages, to ensure the applicable regulations are respected.
CHILD SEATS: attachment using the isofix system (5/6) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted. i-U = Suitable for the i-Size restraint devices in the “universal” forward-facing and backward-facing category. (1) If necessary, position the vehicle seat as far back as possible.
CHILD SEATS: attachment using the isofix system (6/6) Visual installation of seven-seater version Child seat fitted using the ISOFIX mounting ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached. The anchorage points are located on the backs of the rear seats.
CHILD SAFETY: deactivating/activating the front passenger air bag (1/3) The front passenger air bag must only be deactivated or activated when the vehicle is stationary. 2 If it is interfered with when the vehicle is being driven, indicator lights 1 å and © will come on. Switch the ignition off then on again to reset the air bag in accordance with the lock position.
CHILD SAFETY: deactivating/activating the front passenger air bag (2/3) A A 3 DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER fit a restraint system for a rear-facing child in a seat protected by an ACTIVATED front AIRBAG. This can cause the CHILD’S DEATH or SERIOUS INJURY. 1.60 The markings on the dashboard and labels A on each side of the passenger sun visor 3 (example: label shown above) remind you of these instructions.
CHILD SAFETY: deactivating/activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbag activation/deactivation system is faulty. 2 1 Allowing any other passenger to sit in that seat is not recommended. Contact your approved dealer as soon as possible.
DRIVING POSITION (1/2) 1 2 3 4 5 6 7 9 8 28 12 9 13 14 18 26 25 24 23 17 15 2 1 16 22 19 27 1.
DRIVING POSITION (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 11 Multimedia touchscreen. 18 Storage compartment. 2 Side window demister outlet. 12 Multifunction screen controls: – screen activation/deactivation; – volume; – welcome menu; – driving aids menu; – settings. 19 Assisted parking brake control. 3 Stalk for: – direction indicator lights; – exterior lights; – rear fog lights. 4 Driver Airbag and horn location. 5 Instrument panel.
WARNING LIGHTS (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. A š á k f Side light warning light Main beam headlight telltale Dipped beam headlight telltale Rear fog lights tell-tale Automatic main beam headlight indicator light Please refer to the information on “External signals and lights” in Section 1.
WARNING LIGHTS (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. D A Brake circuit fault warning light It lights up when the ignition or the engine is switched on and goes off after a few seconds. If it comes on during braking and is accompanied by the ® warning light and a beep, it indicates that the fluid level in the circuit is low or that there is a braking system fault. Stop as soon as traffic conditions allow and contact an authorised dealer.
WARNING LIGHTS (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Ä A Warning light © This lights up when the ignition or engine is switched on and goes out as soon as the engine is running. It can light up in conjunction with other warning lights and/or messages on the instrument panel. It means you should drive very carefully to an approved dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. 1.
WARNING LIGHTS (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Rear seat belt reminder (depending on vehicle) ß A É Preheating warning light (diesel version) This should come on when the ignition is switched on. It indicates that the heater plugs are in operation. It goes out when preheating is complete. The engine can be started.
WARNING LIGHTS (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Speed limiter, cruise control and adaptive cruise control warning lights Φ A Please refer to the information on the “Speed limiter”, “Cruise control” and “Adaptive cruise control” in Section 2. Engine standby warning light Please see information in the paragraph on “Stop and Start Function” in Section 2.
WARNING LIGHTS (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Driver’s seat belt reminder and, depending on the vehicle, front passenger seat belt reminder. This lights up in the rear-view mirror when the ignition is started then, if the driver or front passenger seat belt (if this seat is occupied) is not fastened and the vehicle has reached approximately 12 mph (20 km/h), it flashes and a beep sounds for around 120 seconds.
DISPLAYS AND INDICATORS (1/4) Driving style indicator 3 Please refer to the information on “Ecodriving” in Section 2. 1 A 2 3 Instrument panel A Rev counter 1 You can customise your instrument panel with the content and colours of your choice. (graduations x 1000) Speedometer 2 From the multifunction screen, select: – one of the Multi-Sense modes. Please refer to the information on “Multi-Sense” in Section 3; – menu “System” then “User profile”. Refer to the handbook for the equipment.
DISPLAYS AND INDICATORS (2/4) 6 B A 4 5 Engine oil level low warning Coolant temperature indicator 5 Fuel gauge 6 When the engine is started, the instrument panel display A alerts you when the minimum oil level is reached. Refer to the information on the “Engine oil level” in Section 4. In normal use, indicator 5 should be before area B. Under “intensive” operating conditions, the needle may approach this zone.
DISPLAYS AND INDICATORS (3/4) 7 You can adjust certain settings from the multifunction screen: with the engine running, access menu “System”, “Display” then “Head-up display”. Adjusting the display information height Depending on your driving position, you can raise or lower the information on the display. Adjusting the display brightness Head-up display 7 The display details driving and navigation information from the instrument panel and the multifunction screen.
DISPLAYS AND INDICATORS (4/4) Operating faults In the event of a malfunction (the display fails to open when the engine is started, or the display retracts, with the engine running, following an object impacting the display): – stop and restart the engine; or – from the multifunction screen, change the display opening settings. If there is still a problem, contact an authorised dealer. Multifunction screen B Please see the equipment instructions or the sections dealing with the relevant functions.
TRIP COMPUTER: general information (1/2) Display selection keys 2 Scroll through the following information by repeated short presses on button 2 (the display depends on the vehicle equipment and country): 1 2 a) total mileage and trip mileage recorder; b) journey parameters: – fuel used; – average fuel consumption; – current fuel consumption; – estimated range; – distance travelled; – average speed; On-board computer 1 c) mileage before service; Depending on the vehicle, this includes the following fu
ON-BOARD COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting The values showing average fuel consumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed. 3 Trip mileage resetting With “trip mileage recorder” selected on the display, press key OK 3 until the mileage recorder resets to zero.
ON-BOARD COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km a) Total mileage and trip mileage recorder. Fuel used 8L Middle 5.8 L/100 Current 7.4 L/100 1.76 b) Journey parameters: Fuel used. Fuel consumed since the last reset. Average fuel consumption since the last reset. The value is displayed after having travelled at least 400 metres since the last reset.
ON-BOARD COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Range 541 km Interpreting the display selected b) Journey parameters (continued): Estimated range with remaining fuel. The value is displayed after driving 400 metres. Distance 522 km Middle 123.4 km/H Distance travelled since last reset. Average speed since the last reset. The value is displayed after driving 400 metres. 1.
ON-BOARD COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections On-board computer with mileagebefore-service message Interpreting the display selected c) Mileage before service or oil change.
TRIP COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections On-board computer with distance before next service message (cntd.) Service Intervals Oil change in 30 000 Kms / 24 mo Service due in 300 Kms / 24 days Service required Interpreting the display selected c) Mileage before service or oil change.
ON-BOARD COMPUTER: trip settings (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected d) Tyre pressure reset + No message memorised Tyre pressure Refer to the information on the “Tyre pressure monitoring system” in Section 2. e) Trip log. Successive display: – information messages (passenger airbag OFF etc.); – operating fault messages (Check injection system, etc.). 1.
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages « Parking brake on » « Checking control functions » Interpreting the display selected Indicates that the parking brake has been applied. Displayed with the ignition on when the vehicle is running self-diagnostics.
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given in the following pages.
TRIP COMPUTER AND WARNING SYSTEM: warning message These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Some examples of warning messages are given below. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
VEHICLE SETTINGS CUSTOMISATION MENU 1 Adjusting the settings Select the function to modify: a) unlocking the driver’s door; b) automatic locking of the doors while driving; c) hands-free function; d) indicator audio volume; e) internal welcome sound; f) external welcome; g) reading lamp in automatic mode; h) rear windscreen wiping in reverse gear; i) configuration of the driving style indicator; j) Active noise control.
CLOCK AND EXTERIOR TEMPERATURE 1 External temperature indicator Special note: When the exterior temperature is - 3 °C to + 3 °C, the °C characters flash (signalling a risk of ice on the road). The time and/or external temperature are displayed on the multifunction screen 1 Refer to the handbook for the equipment. External temperature indicator As ice formation is related to climatic exposure, local air humidity and temperature, the external temperature alone is not sufficient to detect ice.
STEERING WHEEL/POWER-ASSISTED STEERING Power-assisted steering Variable power-assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. 1 NB: power-assisted steering depends on the mode selected in the “MultiSense” menu (please refer to the information in “Multi-Sense” in Section 3).
REAR-VIEW MIRRORS (1/3) D E 2 1 A B Folding door mirrors Welcome and goodbye function The door mirrors automatically fold in when the vehicle is locked (switch 3 in position B). From the multifunction screen, select menu “Vehicle”, “User settings”, “External welcom” and activate or deactivate the function (ON or OFF). In any case, you can make the door mirrors fold in (switch 3 in position C) or fold out (switch 3 in position A). Automatic mode is then deactivated.
REAR-VIEW MIRRORS (2/3) Position memory – Adjust the door mirrors (see previous paragraphs); – from the multifunction screen, select menu “Vehicle”, “Seats”, “Settings” then “Position” and select “Save”. 1 2 The positions of the door mirrors in a forward gear, reverse and of the front seats are simultaneously saved. Recalling the memorised position From the multifunction screen, select menu “Vehicle”, “Seats”, “Settings” then “Position” and select “Recall”.
REAR-VIEW MIRRORS (3/3) 4 A 3 C Special feature: Interior rear view mirror When the rear-view mirror has been manually deployed or folded back, it is possible to reset it to a usage position. To do this, position the switch 3 to C. A mechanical noise from the rear-view mirror unit will be heard. The rear-view mirror 4 automatically darkens when you are being followed by a vehicle using main beam headlights or in very bright lighting.
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. 1 One-touch mode A Horn Press the steering wheel boss A to activate the horn. Headlight flasher Pull stalk 1 towards you to flash the headlights. 2 When driving, it is possible that the steering wheel may not be turned sufficiently to return the stalk automatically to its starting position.
EXTERIOR LIGHTING AND SIGNALS (1/5) 1 2 3 Side lights Turn ring 3 until the symbol is opposite mark 2. This indicator light on the instrument panel comes on. Dipped beam headlights Manual operation Turn ring 3 until the symbol is opposite mark 2. This indicator light on the instrument panel comes on.
EXTERIOR LIGHTING AND SIGNALS (2/5) Automatic main beam headlights 1 Depending on the vehicle, this system switches the main beam headlights on and off automatically. The function uses a camera located behind the interior rear-view mirror to detect vehicles that are following and coming in the opposite direction. The main beam headlights come on automatically if: – exterior light is weak; – no other vehicles or lighting are detected; – the vehicle speed is above approximately 30 mph (45 km/h).
EXTERIOR LIGHTING AND SIGNALS (3/5) 1 2 3 Operating faults When the message “Check auto lighting” appears on the instrument panel, the system is deactivated. Consult an approved dealer. Daytime running lights function Switching off the lights Operating faults There are two possibilities: – manually, move ring 3 to position 0; – automatically, the lights will go out when the engine is switched off, the driver’s door is opened or the vehicle is locked.
EXTERIOR LIGHTING AND SIGNALS (4/5) “See-me-home lighting” function This function allows you to briefly switch on the dipped beam headlights (to provide light when opening a gate, etc.). With the engine and lights off and ring 3 in position 0 or AUTO, pull stalk 1 towards you: the dipped beam headlights come on for approximately thirty seconds. To increase this duration, you may pull the stalk up to four times (total time restricted to two minutes).
EXTERIOR LIGHTING AND SIGNALS (5/5) 1 2 Switching off the lights Turn ring 4 again until mark 2 is opposite the symbol for the fog light that you wish to switch off. The corresponding indicator light on the instrument panel goes out. The rear fog lights switch off when the exterior lights are switched off. 4 f Rear fog lights Turn centre ring 4 on the stalk until the symbol faces mark 2, then release it.
WINDSCREEN WASH/WIPE (1/6) 1 1 2 A B C E Check the condition of the wiper blades. You are responsible for their service life: D Vehicle fitted with intermittent windscreen wipers A single sweep A short push will trigger one sweep of the wipers. B stop C intermittent wiping The wipers will pause for several seconds between sweeps. It is possible to change the time between sweeps by turning ring 2.
WINDSCREEN WASH/WIPE (2/6) When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed. 1 1 F 2 A B C E D Vehicle fitted with front windscreen wiper rain sensor The rain sensor is located on the windscreen, in front of the interior rear-view mirror. A single sweep A short push will trigger one sweep of the wipers.
WINDSCREEN WASH/WIPE (3/6) Operating fault Special note In the event of a malfunction of the automatic wiping, the wiper is set to intermittent wiping. Contact an authorised dealer.
WINDSCREEN WASH/WIPE (4/6) Specific front wiper position (service position) This position enables the blades to be lifted to remove them from the windscreen. This can be useful: – to clean the blades; – to release the blades from the windscreen in winter; – to replace the blades (please refer to the information on the “Wiper blades” in Section 5). With the ignition on and the engine off, lower the windscreen wiper stalk fully (fast continuous wipe position).
WINDSCREEN WASH/WIPE (5/6) Note: In temperatures below zero, the washer liquid risks freezing to the windscreen, thereby reducing visibility. Heat the windscreen using the demister control before cleaning. 1 A B C E D Windscreen washer With the ignition on, pull stalk 1 then release. A brief pull will trigger a single sweep of the wipers, in addition to the windscreen washer.
WINDSCREEN WASH/WIPE (6/6) Note: To ensure the headlight washers operate correctly in winter, remove snow from the jet trims and de-ice the jet trims using an aerosol de-icer. 1 A B C E D Headlight washers You are recommended to regularly remove dirt encrusted on the headlight glass. When the minimum windscreen washer fluid level is reached, the headlight washer system may be deprimed.
REAR SCREEN WASH/WIPE (1/2) To stop the operation, pivot ring 3 again. 1 2 3 Note: When washing using a roller type car wash, return the ring 3 on the stalk 1 to the stop position to deactivate automatic wiping. Follow usage recommendations. Check the condition of the wiper blades.
REAR SCREEN WASH/WIPE (2/2) Activation/deactivation of the rear screen wiper Engaging reverse gear triggers intermittent wiping (if the front wipers are in operation). If your vehicle is fitted with a vehicle settings customisation menu, you can opt to activate or deactivate this function. To do this, refer to the information on the “Vehicle settings customisation menu” in Section 1; “Rear wiping in reverse gear”.
FUEL TANK (1/3) Diesel versions Only use diesel fuel which complies with the information on the label located inside the cover 1. 1 2 1 It is essential to use unleaded petrol. The octane rating (RON) must comply with the information given on the label on the cover 1. Refer to Section 6 for information on “Engine specifications”. A Useable fuel tank capacity: approx. 58 litres. With the vehicle unlocked, to open cover 1, press area A then release. The cover 1 opens.
FUEL TANK (2/3) Filling with fuel Insert the nozzle to open the valve 2 and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position throughout the entire filling operation. 2 3 When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be sufficient space in the fuel tank to allow for expansion. Make sure that no water enters the fuel tank during filling.
FUEL TANK (3/3) 3 Running out of fuel on diesel versions With the card RENAULT in the passenger compartment, press the start button 3 without pressing any of the pedals. Wait a few minutes before starting. This will enable the fuel circuit to be primed. If the engine does not start, repeat the procedure. If the engine does not start after several attempts, please contact an authorised dealer. 1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting - Stopping the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop and Start Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN Petrol version Diesel version Up to 600 miles (1 000 km), do not exceed 78 mph (130 km/h) in top gear or 3,000 to 3,500 rpm. For the first 900 miles (1 500 km), do not exceed 2,500 rpm. After completing this mileage you may drive faster, however, it is only after approximately 3600 miles (6 000 km) that you may reasonably expect full performance. You may only expect top performance from your vehicle after approximately 1,800 miles (3 000 km).
STARTING/STOPPING THE ENGINE (1/3) “Hands-free” starting with the tailgate open 2 In this case, the RENAULT card should not be located in the boot, to avoid any risk of loss. 1 The RENAULT card must be inserted in detection zone 1. To start: – vehicles with an automatic gearbox, place the lever in position P, depress the brake pedal and press button 2; – vehicles with a manual gearbox, depress the brake or clutch pedal and press the button 2.
STARTING/STOPPING THE ENGINE (2/3) 2 3 Depress the brake or clutch pedal, then place the RENAULT 3 card (logo side) in contact with the start button 2 for around 2 seconds. Press the 2 button to start the vehicle. The message goes out. Driver’s responsibility Never leave an animal, child or adult who is not self-sufficient alone in your vehicle, even for a short time.
STARTING/STOPPING THE ENGINE (3/3) 2 If the RENAULT card is no longer in the passenger compartment when you try to switch the engine off, the message “No keycard Press and hold” appears on the instrument panel: press the button 2 for longer than two seconds. If the card is no longer in the passenger compartment, make sure you can retrieve it before pressing and holding the button. Without the card RENAULT , you will not be able to start.
STOP AND START FUNCTION (1/4) This system enables a reduced fuel consumption and lower greenhouse gas emissions. The system is activated automatically when the vehicle is started. While driving, the system stops the engine (standby) when the vehicle is at a standstill (traffic jam, traffic lights, etc). Conditions for engine standby For vehicles equipped with manual gearboxes: – the gearbox is in neutral; and – The clutch pedal is released.
STOP AND START FUNCTION (2/4) Preventing the engine from standing by Conditions for coming out of engine standby In certain situations, such as negotiating a crossroads for instance, it is possible to keep the engine running so as to be ready to move off quickly.
STOP AND START FUNCTION (3/4) Conditions preventing the standby of the engine Certain conditions prevent the system from using the engine standby function, including when: – reverse gear is engaged; – the bonnet is not locked; – the driver’s door is not closed; – the driver’s seatbelt is not fastened; – the outdoor temperature is too low or too high (less than around 0 °C or higher than around 30 °C); – the battery is not sufficiently charged; – for vehicles with automatic gearboxes, the gradient is steepe
STOP AND START FUNCTION (4/4) Special feature of the automatic engine re-start The system reactivates automatically each time the vehicle is started using the start button (please refer to “Starting, stopping the engine” in Section 2). Under certain conditions, the engine can restart on its own in order to guarantee your safety and comfort.
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions should be avoided: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved. If you notice any of the above operating faults, have the necessary repairs carried out as soon as possible by an approved dealer.
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected. If the message “Check anti-pollution system” is displayed along with warning Ä lights and ©, consult an authorised dealer immediately.
GEAR LEVER 1 Selecting reverse gear Vehicles with manual gearbox: follow the grid drawn on knob 1, and depending on the vehicle, lift ring against the gear lever knob to select reverse. Vehicle with automatic gearbox: refer to the information on the “Automatic gearbox” in Section 2. The reversing lights will come on as soon as reverse gear is selected with the ignition on. 2.12 An impact to the underside of the vehicle while manoeuvring (e.g.
ELECTRONIC PARKING BRAKE (1/3) Note: 1 To indicate that the electronic parking brake is released, a beep sounds and the message “Apply parking brake” appears on the instrument panel: 2 3 – with the engine running: when the driver’s door is opened; – with the engine switched off (eg. when the engine stalls): when a front door is opened. In this case, pull and release switch 2 to apply the assisted parking brake.
ELECTRONIC PARKING BRAKE (2/3) Special cases 3 1 2 Manual operation You can control the electronic parking brake manually. Applying the electronic parking brake Pull switch 2. Warning light 3 and warning light light up. } To manually activate the electronic parking brake, (when stopping at a red light, or stopping when the engine is running, etc.): pull and release switch 2. The brake is released as soon as the vehicle is started up again.
ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic gearbox In the event of message “Electric failure DANGER” or “Check battery”, manually activate the electronic parking brake by pulling switch 2 (or position the gear lever in P for automatic gearboxes) before stopping the engine. For safety reasons, automatic release is deactivated when the driver’s door is open or not shut properly and the engine is running (in order to prevent the vehicle from moving without the driver).
DRIVING ADVICE, ECO-DRIVING (1/5) Fuel consumption is accredited in accordance with a standard regulatory method. Identical for all manufacturers, this enables vehicles to be compared with one another. Consumption in real time depends on vehicle usage conditions, the equipment fitted and the user’s driving style. To optimise fuel consumption, please refer to the following advice.
DRIVING ADVICE, ECO-DRIVING (2/5) 4 An overall rating from 0 to 100 is displayed to let you assess your eco driving performance. The higher the rating, the lower the fuel consumption. Eco advice is given to help improve your performance. With your favourite journeys saved, you can compare your performance between trips and the performance of other vehicle users. For more information, please see the multimedia system instructions.
DRIVING ADVICE, ECO-DRIVING (3/5) ECO mode Disabling the function ECO mode is a function which optimises fuel consumption. This acts on all power consuming elements (engine power, switching gears for vehicles fitted with an automatic gearbox, heating and/or air conditioning, etc.). Press switch 4. Limiting acceleration enables low fuel consumption in urban and surrounding areas. The air conditioning and heating limiter enables you to save fuel without affecting your heating comfort.
DRIVING ADVICE, ECO-DRIVING (4/5) Driving advice, Eco-driving – Do not overrev the engine in the intermediate gears. You should always use the highest gear possible. – Avoid sudden acceleration. – Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on flat ground. Keep your foot in the same position on the accelerator pedal.
DRIVING ADVICE, ECO-DRIVING (5/5) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Recommendations for reducing consumption and therefore helping to preserve the environment: – Tyres Advice on use – An underinflated tyre increases fuel consumption.
MAINTENANCE AND ANTIPOLLUTION ADVICE Your vehicle complies with criteria for recycling and recovering vehicles at the end of their service life which will come into force in 2015. Some parts of your vehicle have therefore been designed to facilitate future recycling. These parts are easy to remove so that they can be recovered and reprocessed by recycling companies. By virtue of its design, moderate fuel consumption and initial settings, your vehicle also conforms to current antipollution regulations.
ENVIRONMENT Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the Renault eco² signature. Emissions Manufacture Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
TYRE PRESSURE MONITORING SYSTEM (1/3) 1 2 3 Resetting the standard level for the tyre pressures This should be done: – when the standard tyre pressure needs to be changed to adapt to usage conditions (empty, carrying a load, motorway driving, etc.); – after swapping a wheel (however this practice is not recommended); – after changing a wheel. It should always be done after checking the tyre pressure of all four tyres when cold.
TYRE PRESSURE MONITORING SYSTEM (2/3) “Puncture” A wheel B is shown in red, the warning 1 A light 4 comes on, the message “Puncture” appears and there is a beep. This message appears along with the ® warning light. They indicate that the affected wheel is punctured or severely underinflated. Replace it or contact an approved dealer if it is punctured. Top up the tyre pressure if the wheel is deflated.
TYRE PRESSURE MONITORING SYSTEM (3/3) “Tyres location in progress” Replacing wheels/tyres This message “Tyres location in progress” appears when driving if one or more wheels have been fitted with sensors not recognised by Renault. This system requires specific equipment (wheels, tyres, hubcaps, etc.). Please see the information on “Tyres” in Section 5.
DRIVER CORRECTION DEVICES AND AIDS (1/12) ABS (anti-lock braking system) – ABS (anti-lock braking system) ; – ESC (electronic stability control) with understeer control and traction control; Under heavy braking, the ABS prevents the wheels from locking, allowing the stopping distance to be managed and keeping control of the vehicle. – emergency brake assist; – advanced traction control; – active emergency braking; – driver assistance with a trailer; – hill start assistance; – rear wheel steering.
DRIVER CORRECTION DEVICES AND AIDS (2/12) Operating faults: x – © and – , , © and ® lit up on the instrument panel alongside the message “Braking system fault”: this indicates a fault in the braking system. lit up on the instrument panel alongside messages “Check ABS”, “Check braking system” and “Check ESC”: indicates the ABS, ESC and emergency brake assist are deactivated. Braking is always enabled; xD In both cases, consult an approved dealer.
DRIVER CORRECTION DEVICES AND AIDS (3/12) Electronic stability control ESC with understeer control and traction control Electronic stability control ESC This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
DRIVER CORRECTION DEVICES AND AIDS (4/12) Emergency brake assist Braking anticipation This system supplements the ABS and helps reduce vehicle stopping distances. Depending on the vehicle, when you rapidly release the accelerator, the system anticipates the braking manoeuvre in order to reduce stopping distances. Operating principle The system is for detecting an emergency braking situation. In this case, the braking assistance immediately develops maximum power and may trigger ABS regulation.
DRIVER CORRECTION DEVICES AND AIDS (5/12) Advanced traction control If fitted on the vehicle, grip control makes it easier to control the vehicle on low grip surfaces (soft ground, etc.). Activating or deactivating the system Note: The system’s default mode is “Auto” mode. From the multifunction screen, select menu “Vehicle”, “Driving assistance”, “Traction control” then select the mode: « Auto » The “Auto Advanced Traction Control” message is shown on the instrument panel for approximately 15 seconds.
DRIVER CORRECTION DEVICES AND AIDS (6/12) 1 2 Active emergency braking Operation Using the sensor 1, the system calculates the distance separating the vehicle from the one in front and alerts the driver if there is a risk of a front-end collision. The driver can then brake the vehicle to limit the damage arising from a collision.
DRIVER CORRECTION DEVICES AND AIDS (7/12) Conditions for non-activation of the system 3 4 The system cannot be activated: – when the gear lever is in neutral; – when the parking brake is activated; – while cornering. Operating faults When the system detects an operating ” appears on fault, warning light “ the instrument panel along with warning light © and the message “Check Active braking”. Consult an approved dealer.
DRIVER CORRECTION DEVICES AND AIDS (8/12) Active emergency braking This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. System servicing/repairs – In the event of an impact, the sensor alignment may become changed, and its operation will consequently be affected. Deactivate the function, then consult an authorised dealer.
DRIVER CORRECTION DEVICES AND AIDS (9/12) Active emergency braking Limitation of the system operation – The system will only respond to vehicles which are moving or which have been sensed as moving. – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The sensor area should be kept clean and free of any modifications in order to ensure the proper operation of the system.
DRIVER CORRECTION DEVICES AND AIDS (10/12) Driver assistance with a trailer Operating principle This system helps to maintain control over the vehicle while using a trailer. It detects shaking caused by towing a trailer under certain driving conditions.
DRIVER CORRECTION DEVICES AND AIDS (11/12) Hill start assistance This function assists the driver when starting on hills. It prevents the vehicle from rolling backwards by automatically applying the brakes when the driver lifts his/her foot off the brake pedal to depress the accelerator pedal.
DRIVER CORRECTION DEVICES AND AIDS (12/12) A B Operating faults – If the © warning light, together with the message “Check power steering”, is displayed on the instrument panel: please contact an authorised dealer. – If the warning light ®, together with the message “Power steering fault”, is displayed on the instrument panel, this indicates a fault in the system.
LANE DEPARTURE WARNING (1/3) This system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. – – – – – – This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road. However, the function is not intended to replace the driver.
LANE DEPARTURE WARNING (2/3) Conditions for non-activation of alerts 1 2 3 Activation/deactivation From the multifunction screen 1: select “Vehicle”, “Driving assistance”, “Lane departure warning” then choose “ON” or “OFF”. When the function is activated, the visibility indicators 3 for the left and right lines are displayed in grey on the instrument panel.
LANE DEPARTURE WARNING (3/3) Operating faults 1 Adjustment From the multifunction screen 1, select “Vehicle”, “Driving assistance”, “Lane departure warning settings” then in: – volume: adjust the alert volume to one of five levels; – sensitivity: adjust the sensitivity level for line detection. To do this select: – “Low” line detected upon crossing; – “Middle” line detected on approach; – “high” line detected nearby. 2.
BLIND SPOT WARNING (1/3) 1 A 2 A 3 A This system alerts the driver to other vehicles in the detection zone A. The system is activated when the vehicle’s speed is between approximately 30 km/h (19 mph) and 140 km/h (87 mph). This function uses sensors 1 installed in the front and rear bumper of both sides. Activation/deactivation Special feature On the multifunction screen 2, select the “Vehicle” menu, “Driving assistance”, and “Blind spot alert”, and then choose “ON” or “OFF”.
BLIND SPOT WARNING (2/3) Display B 14 The function is activated and has not detected any vehicles. B Display C C 5 Display D D Indicator 4 Operation An indicator light 4 is situated on both door mirrors 5. This function will indicate: Note: Clean the door mirrors 5 regularly, so that the indicator lights 4 can be seen properly. Initial warning: the indicator light 4 shows that a vehicle has been detected in the blind spot.
BLIND SPOT WARNING (3/3) 4 B C Operating faults If the system detects a fault, the message “Check blind spot alert” is displayed on the instrument panel. Consult an authorised dealer. Note: When the engine is started, the indicator light 4 (display B) flashes three times. It is normal. D Conditions for non-function – If the object is not moving; – if traffic is heavy; – the road is winding; – if front and rear sensors both detect objects at the same time (e.g. when passing an articulated lorry). – ...
SAFE DISTANCE ALERT (1/2) 2 1 Using the sensor 1, this function notifies the driver about the time interval separating them from the vehicle in front, so they can respect a safe distance between the two vehicles. Note: make sure that the sensor 1 is not obscured (by dirt, mud, snow, etc.). 3 Activating/deactivating the function From the multifunction screen 2, select menu “Vehicle”, “Driving assistance”, “Distance warning” then choose “ON” or “OFF”.
SAFE DISTANCE ALERT (2/2) A 4 B C D Operation Upon activating the function, indicator 4 notifies the driver of the distance separating them from the vehicle in front. – C (orange): the time interval falls between around 1 and 2 seconds (insufficient distance between the two vehicles); This function is essential if adaptive cruise control is activated. – D (red): the time interval is less than or equal to around one second (very insufficient distance between the two vehicles).
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) Switching on a 3 b 4 2 1 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. Controls 1 Main “On/Off” switch. 2 Controls for: a speed limiter activation, memory and increase (+); b decreasing the speed limiter (-). 3 Activation and recall of memorised limited speed (R). 4 Speed limiter function standby (with limited speed memory) (O).
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The speed limiter can be changed by repeatedly pressing switch 2 : It is possible to exceed the limit speed at any time. To do this: press the accelerator pedal firmly and fully (beyond the resistance point). – side a (+) to increase the speed; a – side b (-) to reduce the speed. 2 While the speed is being exceeded, the speed limiter flashes red on the instrument panel.
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been stored, it can be recalled by pressing switch 3 (R). a 3 2 4 1 Putting the function on standby Switching off the function The speed limiter function is deactivated if you press switch 1: in this case a speed is no longer stored. The orange instrument panel warning light goes out, confirming that the function is stopped. The speed limiter function is suspended when you press switch 4 (O).
OVERSPEED ALERT (1/3) 1 Operating principle The system detects speed limit signs on the side of the road and displays the speed limit. It mainly uses information taken from the camera 1, attached to the windscreen behind the rear-view mirror. Note: Make sure the windscreen is not obstructed (dirt, ice, snow, etc.). The system also uses information from other vehicle systems (navigation GPS, etc.).
OVERSPEED ALERT (2/3) Varying the limit speed 2 a 3 4 b If the speed limiter notification differs from the detected speed value, press and hold switch 4: – side a (+) to increase the notification speed to the detected speed; – side b (-) to reduce the notification speed to the detected speed.
OVERSPEED ALERT (3/3) This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The driver should always adapt their speed to the traffic conditions, regardless of the system indications. The system enables maximum speed signs to be detected and does not detect other traffic signage.
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) a 3 2 1 The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). b 4 Controls 1 Main “On/Off” switch. 2 Controls for: a cruising speed activation, storage and increase (+) ; b decreasing cruising speed (-). 3 Activation with recall of saved cruising speed (R).
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Activating cruise control At a steady speed (above approx. 20 mph or 30 km/h), press switch 2 side a (+): the function is activated and the current speed is saved. The cruising speed replaces the dashes and cruise control is confirmed by the appearance of the message “Check cruise control” and the warning light .
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelerator pedal. While overtaking, the cruising speed flashes red on the instrument panel. a Then, release the accelerator: after a few seconds, the vehicle will automatically return to its set cruising speed.
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Returning to the cruising speed a 3 2 4 Putting the function on standby The function is set to standby if you: – use the switch 4 (O); – the brake pedal; – depress the clutch pedal or the shift into neutral if the vehicle has an automatic gearbox. In these three cases, the cruising speed remains stored and the message “Memorised” accompanied by this speed appears on the instrument panel.
ADAPTIVE CRUISE CONTROL (1/7) When traffic conditions permit (large free-flowing road or motorway), the adaptive cruise control gives you the option of maintaining a chosen speed, known as cruise control, adjustable from 30 mph to 85 mph (50 and 140 km/h), while keeping a following distance from the vehicle in front in the same lane. 1 The sensor has a range of 120 metres. Note: The driver should take into account the maximum speed limit in their location.
ADAPTIVE CRUISE CONTROL (2/7) a 3 6 2 b 4 Controls 5 Main “On/Off” switch. 2 Controls for: a cruising speed activation, storage and increase (+) ; b decreasing cruising speed (-). 3 Activation with recall of saved cruising speed (R). 4 Switch the function to standby (with cruising speed saved) (O). 6 Adjusting following distance. 5 Switching on Press switch 5.
ADAPTIVE CRUISE CONTROL (3/7) Driving Varying the following distance Once a cruising speed is memorised and the cruise control function is active, you may lift your foot off the accelerator pedal. If a following distance is stored and a vehicle travelling slower than yours is detected by the system in your lane, your vehicle will brake (with the brake lights on) and adapt its speed to that of the vehicle in front, respecting the following distance selected previously.
ADAPTIVE CRUISE CONTROL (4/7) Putting the function on standby The function is set to standby if: – you press switch 4 (O); a 3 – you depress the brake pedal; – you depress the clutch pedal; 2 – you use the gear lever; 4 – the vehicle speed is lower than 20 mph (40 km/h) or over 100 mph (160 km/h); – certain driver correction devices and aids are triggered (ABS, ESC, etc.) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelerator pedal.
ADAPTIVE CRUISE CONTROL (5/7) Note: if the speed previously stored is much higher than the current speed, the vehicle will accelerate to reach this threshold. Under certain conditions (coming up behind a vehicle moving more slowly, rapid change of lane of vehicles in front, etc.), the system may not have time to respond and may emit a beep alongside the alert A when the situation requires the driver’s attention, or the alert B when the situation requires immediate action from the driver.
ADAPTIVE CRUISE CONTROL (6/7) This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The driver should always adapt their speed to the traffic conditions, regardless of the system indications. The system should under no circumstances be taken to be an obstacle detector or an anti-collision system.
ADAPTIVE CRUISE CONTROL (7/7) Limitation of the system operation – – – – – – – – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The sensor area should be kept clean and free of any modifications in order to ensure the proper operation of the system. Fixed obstacles (vehicles at a standstill, traffic jams, toll booths, etc.) or objects travelling at low speed or of a small size (motorbikes, bicycles, pedestrians, etc.
PARKING DISTANCE CONTROL (1/4) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the vehicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 20 to 30 centimetres from the obstacle. 1 This function is an additional aid that indicates the distance between the vehicle and an obstacle whilst reversing, using sound signals.
PARKING DISTANCE CONTROL (2/4) 2 A C B Note: the display 2 shows the vehicle surroundings and emits beeps. It is necessary to travel a few metres before the side detection is activated. If all areas have a grey background, the whole area around the vehicle is being monitored: – A: analysis of the vehicle surroundings in progress; – B: analysis of the vehicle surroundings carried out 2.64 Operation Most objects located less near the front, rear and sides of the vehicle are detected.
PARKING DISTANCE CONTROL (3/4) If a side obstacle is detected: D – the beeps become faster and then sound continuously as the obstacle gets nearer. Green, orange and red zones will be displayed on the display D; 3 Detection of obstacles to the side Depending on the direction of the wheels, the system determines the trajectory of the vehicle and notifies the driver of any risk or otherwise of a collision with an obstacle 3 to the side of the vehicle.
PARKING DISTANCE CONTROL (4/4) System sound 4 Enables the system sound to be selected from a choice of 3. Deactivating the system sound Activate or deactivate the parking distance control sound. Note: If you deactivate the sound, you will no longer be notified with beeps when approaching an obstacle. Deactivating the system Activate or deactivate parking distance control.
REVERSING CAMERA (1/2) 3 4 3 4 C 2 B A 1 Operation Fixed gauge 3 4 moving guide line: When you change to reverse gear, the camera 1 located on the tailgate provides a view of the area behind the vehicle on the multimedia screen 2, accompanied by one or two fixed or moving guide lines 3 and 4. The fixed clearance gauge comprises coloured markers A, B and C, indicating the distance behind the vehicle: This is shown in blue on the multifunction screen 2.
REVERSING CAMERA (2/2) You can also adjust the camera image settings (brightness, contrast, etc.) 2 Activating, deactivating the reversing camera From the multifunction screen 2, select “Vehicle”, “Settings”, “Parking assistance”, then “Rear view camera”. Activate or deactivate the reversing camera and confirm your choice. The screen shows a reverse mirror image.
ASSISTED PARKING (1/4) 2 3 1 This function assists with parking manoeuvres. Take your hands off the steering wheel. You only control the pedals and the gear lever. You can retake control at any time by operating the steering wheel. Switching on Special features With the vehicle at a standstill or driving at less than 6 mph (10 km/h), press switch 1. The warning light integrated on switch 1 lights up and the 2 screen appears on the multifunction screen.
ASSISTED PARKING (2/4) Choice of manoeuvre Operation The system can perform four types of manoeuvres: Parking – parallel parking; – perpendicular parking; – angle parking; – moving out of a parallel parking space. From the multifunction screen, select the manoeuvre to be performed. Note: When starting the vehicle, or after successfully completed parallel parking using the system, the default manoeuvre proposed by the system is assistance in exiting a parallel parking space.
ASSISTED PARKING (3/4) Your speed should not exceed around 4 mph (7 km/h). Once in position to exit the space, the system will notify you of the end of the manoeuvre. Once the warning light on the instrument panel goes off and a beep sounds, the manoeuvre has been completed. 1 Suspending the manoeuvre Exiting a parallel parking space – Select “exit parallel parking space” mode; – activate the direction indicator on the side you wish to go out of; – press and hold switch 1 (around 2 seconds).
ASSISTED PARKING (4/4) This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. Make sure that the manoeuvre complies with the applicable traffic regulations at your location. – The driver should always look out for sudden hazards during driving: always ensure that there are no moving obstacles (such as a child, animal, pram, bicycle, etc.
ADAPTIVE SUSPENSION Operating fault 1 In the event of a fault, the system switches automatically to the “Neutral” mode in “Multi-Sense”. If the message “Check Damper control” appears on the instrument panel, consult an authorised dealer. Adaptive suspension makes it possible to modify the suspension automatically, according to driving conditions and to your driving style. Choosing a preset mode From the menu on the multifunction screen 1, you can select a preset driving mode.
AUTOMATIC GEARBOX (1/6) A 5 B 4 1 3 2 A Gear selector 3 position grid A Grid B on the instrument panel 1: selector rest position – The current gear is given in zone 5; 2: button P: Park – The available functions are provided in the ambient colour chosen by the driver; R: reverse N: neutral (park) D: automatic mode +: Manually moving up a gear –: Manually moving down a gear 2.74 – Unavailable functions are greyed out, except for position P 4 which disappears from the grid above 2 mph (3 km/h).
AUTOMATIC GEARBOX (2/6) To disengage position P (button 2) 3 2 With the vehicle at a standstill, engine running, depress the brake pedal and move the selector to the desired position R, N or D. If the brake pedal is not fully depressed, the message “Push brake pedal” the warning light are displayed on the instrument panel. When position R or D is disengaged, N is displayed on the instrument panel and the warning light on button 2 goes out.
AUTOMATIC GEARBOX (3/6) Driving in automatic mode Economical driving To select reverse gear With the vehicle at a standstill, engine running, position P, N or R, depress the brake pedal and move the selector to the left then back, and release. When driving, always leave the lever in position D, keeping the accelerator pedal lightly depressed to ensure automatic gear changes at a lower engine speed.
AUTOMATIC GEARBOX (4/6) Driving in manual mode Driving in temporary manual mode Temporary manual mode can only be selected when automatic mode D has been engaged and the vehicle speed is over around 6 mph (10 km/h). Once D engaged, move the selector 3: – to the rear +, to request a higher gear; – forwards -, to request a lower gear. The gear selected is displayed to the right of D on the instrument panel. Special cases Under certain driving conditions (e.g.
AUTOMATIC GEARBOX (5/6) Special cases In certain driving cases (eg: protecting the engine), a gear change can be performed automatically in the event of over-revving or approaching under-revving. Permanent manual mode remains activated. Similarly, to avoid making the "wrong move", a gear change may be refused by the gearbox. In this case, the display for the requested gear + or – flashes for a few seconds to warn you.
AUTOMATIC GEARBOX (6/6) Special circumstances Operating faults – If the bends and road surface do not allow you to stay in automatic mode (e.g. in the mountains), we recommend that you change to either temporary or permanent manual mode. This will prevent the automatic gearbox from changing gear repeatedly when climbing, and permit engine braking on long descents. – When driving, if the “Check auto gearbox” message appears on the instrument panel, it indicates a fault.
2.
Section 3: Your comfort multi-Sense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additional heating and air conditioning . . . . .
MULTI-SENSE (1/2) The Multi-Sense system enables once of five modes to be selected which, depending on the vehicle, affect the drive, the light environment, the comfort and the engine noise: – modes Comfort, Neutral, Eco and Sport are preset and associated with customisable light environments and engine noise; – mode Perso is fully customisable. The drive modes affect the: – power-assisted steering; – piloted suspension damping; – four-wheel drive; – engine and gearbox responsiveness; – heating level.
MULTI-SENSE (2/2) Sport mode This mode allows greater responsiveness from the engine and gearbox, making the suspension and steering firmer. 1 Mode Perso 3 This mode enables you to manually configure the drive, light environment and, depending on the vehicle, the comfort and engine noise. 2 Accessing the menu You can access Multi-Sense: – from the multifunction screen 1.
AIR VENTS: air outlets (1/3) 1 3 2 4 5 6 10 7 8 8 6 8 9 8 7 1 left-hand air vent 2 windscreen demisting vents 6 2nd row passenger air vent 3 centre air vents 7 3rd row passenger air vent 9 Additional air conditioning control 4 side window demister outlets 8 passenger footwell heater outlets 10 multifunction screen 5 right-hand air vent 3.
AIR VENTS: air outlets (2/3) 1 1 2 2 Front seats Direction Right/left: turn knob 2. To fully close, turn beyond the point of resistance. To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. Up/down: lower or raise tabs 1. Do not add anything to the vehicle’s ventilation circuit (for example, to remove bad odours). There is a risk of damage or of fire. 3.
AIR VENTS: air outlets (3/3) 3 5 4 6 2nd row rear seats 3rd row rear seats Right/left direction Right/left direction Move air vent 4. Move air vent 6. Up/down direction Front/rear direction Move cursor 3. Move cursor 5. 3.
AUTOMATIC CLIMATE CONTROL (1/5) 8 1 9 Automatic mode 10 19 18 2 7 6 5 4 3 17 16 15 14 13 11 12 13 The controls 11 and 18 Ventilation speeds. Press zone 14 to access the multifunction screen controls 1. The presence of the controls detailed below will depend on the vehicle model. 12 Passenger compartment air distribution. 2 and 7 Left and right temperature indication adjustment. 3 De-icing/demisting of the rear screen and, depending on the vehicle, the door mirrors.
AUTOMATIC CLIMATE CONTROL (2/5) 8 19 A 18 11 2 7 4 Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. You can still adjust the ventilation speed by pressing buttons 11 or 18 or by sliding your finger in zone A. In this case, the ventilation speed, which is no longer controlled automatically, appears in zone A and zone 14. 3.
AUTOMATIC CLIMATE CONTROL (3/5) 8 To exit this function, press: 10 9 – button 4; – again button 6; – on button 8, 9 or 10. A 18 6 11 4 3 Clear View function This function quickly demists and deices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). It imposes automatic operation of the air conditioning and rear screen de-icing and, depending on the vehicle, the windscreen electric de-icer.
AUTOMATIC CLIMATE CONTROL (4/5) Rear screen de-icing/ demisting 19 17 4 3 Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions. Press button 3 – the integrated indicator light comes on. This function enables rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). To exit this function, press button 3 again. Demisting automatically stops.
AUTOMATIC CLIMATE CONTROL (5/5) Automatic usage Press button 16 (a warning light comes on in zone 14). Manual use Press button 5 to force air recirculation. 16 5 3 Adjusting the distribution of air in the passenger compartment Press buttons 12 to select the desired distribution (a warning light is displayed in zone 14): The air flow is mainly directed to the demisting vents for the windscreen and the side windows. Ø ½ ¿ The air flow is mainly directed to the dashboard air vents.
ADDITIONAL AIR CONDITIONING (1/2) 3 1 2 Control The air conditioning system is used for: The additional air conditioning powers the air vents 3 in the third row to add to the heating level of the second and third rows. – lowering the temperature inside the passenger compartment; It only operates on the flow of cold air blown into the passenger compartment. It can be activated or deactivated using the buttons on the multifunction screen 1, or by the rear control panel 2. 3.
ADDITIONAL AIR CONDITIONING (2/2) 2 5 6 7 4 8 9 12 11 10 Switching on or off Mode MANUAL From the multifunction screen, press button 4. Press button 7 to activate. The rear control 2 is then operational and the warning light 9 goes out. Mode AUTO Press button 6. The system uses the most suitable amount of air to reach and maintain the desired comfort level. Mode OFF Press button 5 to deactivate the function. From the rear control panel 2, move the marker 8 to: AUTO: Turn the control to 11.
AIR CONDITIONING: information and advice on use Advice on use Fuel consumption Operating faults In some situations, (air conditioning off, air recirculation activated, ventilation speed at zero or low, etc.) you may notice that condensation starts to form on the windows and windscreen. You will normally notice an increase in fuel consumption (especially in town) when the air conditioning is operating. As a general rule, contact your approved dealer in the event of an operating fault.
ELECTRIC WINDOWS (1/2) These systems operate: – with the engine running; – with the ignition off until one of the front doors is opened (limited to approximately 12 minutes). – before starting, with the front doors closed, after pressing the start button. Press the window switch down or pull it up to lower or raise the window to the desired height: the rear windows do not open fully.
ELECTRIC WINDOWS (2/2) One-touch mode This mode works in addition to the operation of the electric windows described previously. Briefly press or pull the window switch fully: the window is fully lowered or raised. Pressing the switch again stops the window moving. Remote control window closing (vehicles with 4 one-touch electric windows).
ELECTRIC SUNROOF (1/3) Special features 1 A Pressing button 2 allows the curtain to be automatically positioned depending on the position of the sunroof. 0 B 2 3 Pressing button 2 when the roof and the curtain are in the same opening position enables the curtain to be opened fully. 2 Driver’s responsibility To slide the curtain 1 To slide the sunroof With the ignition on: With the ignition on: – Full opening: move marker 3 on button 2 to position A.
ELECTRIC SUNROOF (2/3) Precautions during use – Vehicle with loaded roof bars. As a general rule, if there is a load on the roof, use of the sunroof is not recommended. Before using the sunroof, check the objects and/or accessories (bike racks, roof boxes, etc.) attached to the roof bars: they should be properly arranged and secured and should not interfere with the operation of the sunroof.
ELECTRIC SUNROOF (3/3)/FIXED GLASS SUNROOF If the blockage persists, keep switch 2 pressed until it closes completely. A 0 2 Please consult an authorised dealer. B 4 Operating fault Fixed glass roof – If the sunroof will not close, turn switch 2 to position B to open the sunroof, then turn switch 2 to position 0 until the sunroof is completely closed.
INTERIOR LIGHTING (1/2) 1 1 1 Map reading lights From the multifunction screen, it is possible to deactivate/activate the courtesy lights upon opening the doors or the boot. To do this, please refer to “Vehicle settings customisation menu” in Section 1. Press switch 1 to get: – permanent lighting; – immediate switching off. When the doors or boot are unlocked and opened, the reading and footwell lights come on temporarily. 3.
INTERIOR LIGHTING (2/2) 3 4 2 Door lights Storage drawer light Boot lights Light 2 comes on when the door is opened. Light 3 comes on when the storage drawer is opened. Light 4 comes on when the boot is opened. 3.
SUN VISOR, BLINDS 1 2 4 3 5 Front sun visor Lateral sun visor Lower the sun visor 1 on the windscreen or unclip it and lower it over the side window. Pull the sun visor up by tab 4 until hooks 5 engage in their housings (make sure the hooks are properly locked in position). Vanity mirror Lift the cover 2. The light 3 switches on automatically. When driving, ensure the courtesy mirror cover is closed. Risk of injury. 3.
PASSENGER COMPARTMENT STORAGE/FITTINGS (1/5) 3 1 4 2 5 Door pockets 1 It can hold a 1.5 litre bottle. Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. Dashboard storage compartment 2 Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning or braking.
PASSENGER COMPARTMENT STORAGE/FITTINGS (2/5) 8 11 12 6 10 7 Cup holders 6 and 9 9 Storage compartments 8 and 10 Storage compartment 7 Central storage compartment 11 Slide the curtain 12 to open the storage compartment. Depending on the vehicle, this may be used to hold a removable cup-holder. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of burning if hot liquid escapes. 3.
PASSENGER COMPARTMENT STORAGE/FITTINGS (3/5) 15 13 Centre console storage compartment 14 Lift up the armrest 13. 16 14 Grab handle 15 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. Clothes hooks 16 3.
PASSENGER COMPARTMENT STORAGE/FITTINGS (4/5 17 18 19 Rear door storage compartment 17 Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. 3.26 Storage drawer 18 under the centre console Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning or braking.
PASSENGER COMPARTMENT STORAGE/FITTINGS (5/5) 20 Rear parcel shelf 20 21 Flap under the feet of the right rear passenger 21 This location houses the tool kit. Please refer to the information on “Tools” in Section 5. 3.
ASHTRAY/CIGAR LIGHTER/ACCESSORIES SOCKET 2 1 Ashtray location 1 Cigarette lighter 2 With the ignition on, push in the cigarette lighter 2 - it will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in. If your vehicle is not fitted with a cigar lighter and an ashtray, these can be obtained from an authorised dealer. 3.28 2 2 1 Accessories sockets You can use the one of sockets 2.
REAR HEADRESTS 2 1 Position for use Lift the headrest to maximum height, then lower it until it locks. To remove the headrest Press the tab(s) 1, then remove the headrest. To refit the headrest Insert the rods into the holes, press tab 1 and lower the headrest. Centre seat headrest 2 storage position Press tab 1 and lower the headrest completely. When the headrest is set at the lowest position, this is for storage only. It should not be in this position when a seat is occupied.
REAR SEATS (1/5) Operating faults When an operating fault is detected, the integrated warning lights on the switch 3 for the seat concerned flash. Consult an approved dealer. 2 3 1 The rear seats are separate seats. To move the seats forwards or backwards Lift lever 1 to unlock the seat. Once in the desired position, release the lever and check that the seat is correctly locked. To tilt the seatback Lift handle 2 and tilt the seatback to the desired position.
REAR SEATS (2/5) To unfold a seat in the second row Hold the seatback, lift it up and ensure it is correctly locked in place. To unfold a seat in the third row 4 – Lift the handle 5 of one of the second-row seats to access the thirdrow seats; – place seat belt in hook 4 to avoid damaging it; – hold the seatback, lift it up and ensure it is correctly locked in place.
REAR SEATS (3/5) Disabling the function 7 – Once the vehicle is moving the two controls are deactivated. 6 To automatically fold down the seats (flat position) The rear seats are electrically unlocked to fold down in order to create a flat floor. There are two ways to manoeuvre the seats: – from the boot using control 6; – from the multifunction screen 7. 3.32 – With the engine running, a buckled seat belt prevents the movement of the relevant seat.
REAR SEATS (4/5) 7 One-touch folding While being moved, if a seat encounters an obstacle, the movement stops of its own accord. You will then have to manually fold back the seat after removing the obstacle. B A Operating fault C D 6 E F All From the multifunction screen 7 Depending on the vehicle, folding switches for: With the vehicle at a standstill, select menu “Vehicle”, “Seats” then “Onetouch folding”. B central rear seat in the second row. C the rear right seat in the second row.
REAR SEATS (5/5) Use restriction It is not permitted to drive with a second row rear seatback or seat folded down when there is a passenger occupying a third row rear seat. The label located on the back of the seats reminds you of this. For safety reasons, carry out any adjustments when the vehicle is stationary. When moving the rear seats, ensure that nothing obstructs the anchorage points (passenger’s arm or leg, a pet, gravel, cloth, toys, etc.). 3.
TAILGATE 3 4 1 2 Manual controls To open Opening the doors manually from the inside Press button 1 and lift the tailgate. If it is impossible to unlock the tailgate, it can be done manually from inside: To close – access the boot by tilting the rear seat(s); Lower the boot lid using the handle inside the boot 2 to assist you. 5 – slide the tab 5 to the right in vehicles with a manual tailgate, or tab 4 on vehicles with an automatic tailgate.
LUGGAGE COMPARTMENT COVER 3 1 2 4 5 4 5 2 To remove the flexible section of the luggage cover Refitting the luggage compartment cover Luggage compartment cover storage Pull handle 1 gently to release the pins from their mounting points located on each side of the boot. Place the luggage cover into the housing points 3. Vehicles without additional air conditioning Lift the false floor 4, remove the attachment strips 5 and position the luggage cover roller 2.
BOOT STORAGE SPACE AND FITTINGS 3 4 1 2 5 Bag hooks 1 Maximum weight per hook: 5 kg. Storage compartment under boot false floor Depending on the vehicle, to access, lift the false floor of the boot 5 using the handle 2. The false floor can be attached using the hook 4 in the housing 3. 3.
TRANSPORTING OBJECTS IN THE BOOT A B 1 Always place the objects to be transported so that their largest side rests against the back of the rear seat for normal loads (e.g.: A), or against the back of the front seats B when the rear seatbacks are folded down. If you have to place objects on the folded seat back, it is vital that you remove the headrests before folding the seat back so that it can be folded as flat as possible against the seat. 3.
TRANSPORTING OBJECTS towbar A A: 1027 mm. Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. Choice and fitting of towing equipment Maximum weight of towing equipment: 32 kg For fitting and conditions of use, refer to the equipment’s fitting instructions. Please keep these instructions with the rest of the vehicle documentation.
LUGGAGE NET (1/2) A 1 2 3 B 4 5 Depending on the vehicle, this may be used when transporting animals or luggage to isolate them from the passenger section. Fitting the luggage net behind the front seats – attach the two hooks 5 for the net straps 3 to the anchoring points 4 Inside the vehicle on each side: – adjust the net strap 3 so that it is taut.
LUGGAGE NET (2/2) 6 7 6 8 9 10 11 Fitting the luggage net behind the rear seats (behind the second row rear seats on the 7-seater version) Inside the vehicle on each side: – push the second row seats fully forward; – lift cover 6 to access the luggage net upper mounting rail; – fix the net belt hook 11 onto the anchoring points 10; – adjust net strap 9 so that it is taut. – adjust the position of the second row seats: ensure that the seatbacks do not touch the luggage net.
ROOF BARS 1 1 Access to the mounting points Open the doors to access the mounting points 1. For information on the range of equipment adapted to your vehicle, we advise you to consult an approved Dealer. Refer to the fitting instructions for information on how to fit roof bars and conditions of use. If original roof bars, approved by our Technical Department, are supplied with screws, only use these screws for attaching the roof bars to the vehicle. 3.
MULTIMEDIA EQUIPMENT (1/2) 1 4 5 2 3 Multimedia systems 1 2 3 4 5 Multimedia touchscreen display; Central control; Steering column controls; Steering wheel controls; Microphone. Hands-free telephone integrated control For equipped vehicles, use the steering wheel controls 4. Using the telephone Refer to the equipment instructions for information on how to operate this equipment. We remind you of the need to conform to the legislation in force concerning the use of such equipment. 3.
MULTIMEDIA EQUIPMENT (2/2) Multimedia sockets 7 Sockets USB can only recharge accessories with a maximum power rating of 12 Watts (voltage: 5V) per socket, which have been approved by our Technical Department. The JACK socket enables the radio to be used with an auxiliary cable. 6 7 Multimedia sockets 6 You can use sockets USB or the SD card reader to access the multimedia content of your accessories and the system update (please refer to the equipment instructions).
Section 4: Maintenance Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level: topping up/filling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oil change . . . . . . . . . . . . . . . . . . . . . . . . . .
BONNET (1/2) 2 1 3 To open, pull handle 1, located on the left-hand side of the dashboard. Unlocking the bonnet catch To unlock, push tab 3 at the same time as opening the bonnet. Opening the bonnet Before performing any action in the engine compartment, the ignition must be switched off by pressing the engine stop button (please see the information on “Starting, stopping the engine” in Section 2). 4.2 Lift the bonnet, guiding it up, and it will rest in position with the help of two struts 2.
BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight. After carrying out any work in the engine compartment, check that nothing has been left behind (cloth, tools, etc.). These may damage the engine or cause a fire. Ensure that the bonnet is properly locked.
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. B A However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
ENGINE OIL LEVEL: topping up, filling (1/2) 1 2 1 2 Topping up/Filling – Unscrew cap 1; The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). – top up the level (as a guide, the capacity between the minimum and maximum reading on the dipstick 2 is between 1.
ENGINE OIL LEVEL: topping up, filling (2/2)/OIL CHANGE Oil change Engine oil grade Service interval: refer to the Maintenance Service Booklet for your vehicle. Refer to the Maintenance Service Booklet for your vehicle. Oil change capacity Please refer to the maintenance document for your vehicle, or contact an authorised dealer. Always check the engine oil level using the dipstick, as explained previously (it should never fall below the minimum level, or be over the maximum level on the dipstick).
LEVELS (1/3) 1 Checking intervals Replacement intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). Refer to the Maintenance Document for your vehicle. If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – anticorrosion protection of the cooling system. The engine may be hot when carrying out operations in close proximity.
LEVELS (2/3) 2 Level 2 Topping up It is normal for the level to drop as the linings become worn, but it should never drop below the “MINI” warning line. After any operation on the hydraulic circuit, a specialist must replace the fluid. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website. Only use fluids approved by our Technical Department (and taken from a sealed container).
LEVELS (3/3)/FILTERS 3 Liquid Filters Windscreen washer fluid. In winter, use anti-freeze product. Use products recommended by an authorised dealer. The replacement of filter elements (air filter, passenger compartment filter, diesel filter, etc.) is scheduled in the maintenance operations for your vehicle. Note: Do not use pure water (risk of damage to the priming pump, limescale building up on the pump and the jets).
BATTERY (1/2) 1 Depending on the vehicle, a system continuously checks the battery charge status. If this decreases, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine and the message on the instrument panel will disappear. The charge status of your battery can decrease especially if you use your vehicle: – for short journeys; – for driving in town; – when the temperature drops; The battery 1 does not require any maintenance.
BATTERY (2/2) Replacing the battery A 2 7 3 4 6 5 As this operation is complex, we advise you to contact an approved Dealer. Label A Observe the indications on the battery: – 2 Naked flames and smoking are forbidden; – 3 eye protection required; – 4 keep away from children; – 5 explosive materials; – 6 refer to the handbook; – 7 corrosive materials. dealer. The battery is a specific type, please ensure it is replaced with the same type. Consult an approved 4.
TYRE PRESSURE (1/2) Vehicle fitted with a tyre pressure monitoring system A In cases of under-inflation (puncture, A low pressure, etc.), warning light lights up on the instrument panel. Please refer to the information on the “Tyre pressure monitoring system” in Section 2. Vehicle used fully laden (Maximum Permissible All-up Weight) and towing a trailer Label A Open the door to read it. Tyre pressures should be checked when the tyres are cold.
TYRE PRESSURES (2/2) Tyre safety and use of snow chains: Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains. For your safety, please respect the speed limit. When they need to be replaced, only tyres of the same make, size, type and profile should be used on a single axle. They must: either have a load capacity and speed rating at least equal to those of the original tyres, or conform to those recommended by an authorised dealer.
BODYWORK MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Your vehicle has been treated with very effective anti-corrosion products. It is nevertheless subject to various outside influences. Corrosive agents in the atmosphere – atmospheric pollution (built-up and industrial areas), – saline atmospheres (near the sea, particularly in hot weather), – seasonal and damp weather conditions (e.g.
BODYWORK MAINTENANCE (2/2) Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway). Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. Remember to visit the body shop periodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Document.
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. Glass instrument panel A stain should always be dealt with swiftly. Use a soft cloth (or cotton wool). If this does not clean them properly, use a soft cloth (or cotton wool) slightly moistened with soapy water and then wipe clean with another soft damp cloth or cotton wool. Finally, carefully dry off with a soft dry cloth.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
4.
Section 5: Practical advice Puncture/emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel trims - wheel . . . . . . . . . . . . . . .
PUNCTURE, EMERGENCY SPARE WHEEL (1/3) In case of puncture Depending on the vehicle, a tyre inflation kit or emergency spare wheel is provided (refer to the following pages). Special note The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emergency spare wheel disappears from the instrument panel display). Refer to the information on the “Tyre pressure monitoring system” in Section 2.
PUNCTURE, EMERGENCY SPARE WHEEL (2/3) 1 2 4 3 5 Emergency spare wheel It is located under the vehicle. From the boot: – for vehicles fitted with a servo, unscrew the three mounting bolts 1 then move the servo 2 to access the cover 3; – lift cover 3; – only use the wheel brace 4 (using a different tool could damage the mechanism) to unroll the retaining cable, and the wheel falls to the ground.
PUNCTURE, EMERGENCY SPARE WHEEL (3/3) 1 4 3 5 6 To refit a wheel To carry out this operation, the cable must be unwound. Stand the wheel up with the valve towards you. Thread the cable and the component 5 through the wheel rim. Rest the wheel with the valve 6 towards the ground. From the luggage compartment, tighten the bolt fully in order to wind the retaining cable, ensuring that the wheel remains horizontal and the cable taut. 5.4 2 Reposition the blanking cover then the cover 3.
TYRE PRESSURE KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE PRESSURE KIT (2/3) – end piece 3 must be connected to a vehicle accessories socket; 2 9 3 1 8 7 6 In the event of a puncture, use the kit situated under the second row rear passenger footwell flap 1. 5 4 With the engine running and the parking brake applied, – press switch 5 to inflate the tyre to the recommended pressure (please refer to the information on “Tyre inflation pressure” in Section 4); – after a maximum of 15 minutes, stop inflating and read the pressure (on pressure gauge 6).
TYRE PRESSURE KIT (3/3) 2 Once the tyre is correctly inflated, remove the kit: slowly unscrew the inflation adapter 2 to prevent any repair product from escaping and store the container in plastic packaging to prevent the product from escaping. – Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; – Put the kit away. – At the end of this initial inflation operation, air will still escape from the tyre.
TOOLS (1/2) 3 6 Jack 3 4 Fold it correctly before refitting it in its housing (ensure that the wheelbrace is correctly positioned 4). B 1 2 Hubcap tool 5 5 This tool is used to remove the wheel trims. 7 Tow eye 6 6 A B Tool kit storage The tool kit is located in flap 1 under the feet of the right-hand second row passenger. To refit, reposition the tools in their housing and fold the jack fully. Check that the assembly is correctly positioned (to avoid noise). 5.
TOOLS (2/2)/WHEEL TRIM D Do not leave the tools unsecured inside the vehicle as they may come loose under braking. After use, check that all the tools are correctly clipped into the tool kit, then position it correctly in its housing: risk of injury. If wheel bolts are supplied in the tool kit, only use these bolts for the emergency spare wheel: refer to the label affixed to the emergency spare wheel. The jack is designed for wheel changing purposes only.
CHANGING A WHEEL (1/2) Vehicles equipped with a jack and wheelbrace If necessary, remove the wheel trim. 1 3 2 Switch on the hazard warning lights. Open the door nearest the wheel concerned to identify the arrow 1 indicating the jacking point 3. If the vehicle is not equipped with a jack or wheelbrace, you can obtain these from your approved dealer. Keep the vehicle away from traffic and on a level surface where it will not slip.
CHANGING A WHEEL (2/2) Turn the wheelbrace until the wheel lifts off the ground. Undo the bolts and take off the wheel. Fit the emergency spare wheel onto the hub and rotate it until the mounting holes in the wheel coincide with those of the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel. Tighten the bolts, checking that the wheel is correctly positioned on its hub and unscrew the jack.
TYRES (1/3) The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. You must make sure that your tyres conform to local road traffic regulations. 2 1 For your safety, please respect the speed limit. When they need to be replaced, only tyres of the same make, size, type and profile should be used on a single axle.
TYRES (2/3) Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label affixed to the edge of the driver’s door). The pressures should be checked cold: ignore higher pressures which may be reached in hot weather or following a high speed journey.
TYRES (3/3) Fitting new tyres For safety reasons, this operation must be carried out by a specialist. Fitting different tyres may change your vehicle as follows: – it may mean that your vehicle no longer conforms to current regulations; – it may change the way it handles when cornering; – it may cause the steering to be heavy; – It may affect the use of snow chains. Use in winter Studded tyres Chains This type of equipment may only be used for a limited period and as laid down by local legislation.
FRONT HEADLIGHTS: changing bulbs 2 3 Main beam headlights 2 Cleaning the headlights Please consult an authorised dealer. Use a soft cloth. If this does not clean it properly, moisten the cloth with soapy water then rinse off. Dipped beam headlights 3 1 Please consult an authorised dealer. Finally, carefully dry off with a soft dry cloth. Direction indicators Cleaning products containing alcohol must not be used. You can replace this bulb.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (1/3) 3 2 1 Side lights, brake lights and direction indicators Consult an approved Dealer. Reversing lights From the boot, unclip the cover on the interior trim of the boot lid. Using a screwdriver, unscrew bolt 2 to remove the light, then change the bulb. From the outside of the vehicle, pull on the light unit to remove it then unscrew bulb holder 3 a quarter of a turn. Replace the bulb. Bulb type: W5W.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (2/3) 5 4 Fog light High level brake light 5 Access bulb holder 4 via the underneath of the vehicle, then unscrew it by turning towards the centre of the vehicle. Consult an approved Dealer. Bulb type: P21W. 5.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (3/3) 6 8 7 Number plate lights 6 Side indicator lights 8 Unclip light 6 by pressing the tab 7. Consult an approved Dealer. Remove the light cover to gain access to the bulb. Bulb type: C5W festoon bulb. 5.
INTERIOR LIGHTING: changing bulbs (1/2) 1 2 Map reading lights 1 Front and rear door lights 2 Please consult an authorised dealer. Unclip door light (using a flat-blade screwdriver or similar) 2. Turn the bulb holder a quarter of a turn and take out the bulb. Bulb type: W5W. 5.
INTERIOR LIGHTING: changing bulbs (2/2) 5 6 7 4 3 Boot lights 3 Unclip light 3 by pressing the tabs on each side (using a flat-blade screwdriver or similar). Disconnect the light. Press tab 5 to release the lens 7 and access the bulb 6. Bulb type: W5W. Passenger storage drawer light 4 Ambient lighting Please consult an authorised dealer. Unclip light 4 by pressing the tabs on each side (using a flat-blade screwdriver or similar). Disconnect the light.
FUSES (1/2) Use the fuse allocation label in storage compartment A to identify the fuses. Certain fuses should only be replaced by a qualified professional. These fuses are not listed on the label. Only change the fuses represented on the label. 1 A Fuse box Tweezers 1 If any electrical component does not work, check the condition of the fuses. Remove the fuse using tweezers 1, located underneath the fuses. Unclip the access flap A.
FUSES (2/2) Allocation of fuses (the presence of certain fuses depends on the vehicle equipment level) Symbol Allocation Symbol Allocation H Windscreen washer ë Third row accessories socket, boot accessories socket Ý Towbar socket Æ Front cigarette lighter, front and rear second row accessories socket Diagnostic socket, audio alarm Not used Heated door mirrors × Brake lights, passenger compartment central unit Parking brake Additional servo î Radio, multifunction screen, m
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (courtesy lights, etc.) are switched off before disconnecting or reconnecting the battery; The battery charger must be compatible with a battery with nominal voltage of 12 volts. – when charging, stop the charger before connecting or disconnecting the battery; Do not disconnect the battery when the engine is running.
BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition. 3 1 2 Start the engine of the vehicle supplying the current and run it at a moderate speed. B A The two batteries must have an identical nominal voltage of 12 volts.
RENAULT CARD: battery 1 A 2 Replacing the battery When the message “Keycard battery low” appears on the instrument panel, replace the battery in the RENAULT card: – slide the rear casing 1 downwards while pressing on zone A; – remove the battery cover 2; – remove the battery by pressing on one side and lifting the other; – replace it according to the direction and template shown inside the cover.
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 watts only. Fire hazard.
WINDSCREEN WIPER BLADES: replacement (1/2) 1 2 3 Windscreen wiper blades 1 With the ignition on and the engine switched off, lower the windscreen wiper stalk fully: the blades stop slightly away from the bonnet. Lift wiper arm 3, press button 2 to release the blade. Refitting Slide the blade along the arm until it clips on. Check that it is correctly locked in place. Lower the windscreen wiper arm carefully. With the ignition on, return the windscreen wiper stalk to the stop position.
WINDSCREEN WIPER BLADES: replacement (2/2) To refit To refit the wiper blade, proceed in reverse order to removal. Make sure that the blade is correctly locked in position. 4 A B 5 6 Rear screen wiper blade 4 Stalk in stop position (deactivated): – Lift the wiper arm 6; – pivot wiper blade 4 until some resistance is met (movement B); – depending on the vehicle, press tab 5, then remove the wiper blade by pulling it (movement A). Keep monitoring the condition of the wiper blades.
TOWING: breakdown (1/2) Before towing, put the gearbox in neutral, unlock the steering column and release the parking brake. For vehicles fitted with an automatic gearbox, if it is not possible to put the gear lever into position N, please consult an authorised dealer. Steering column unlocking Press the engine starter button for approximately two seconds, without depressing the pedals.
TOWING : breakdown (2/2) Use only towing hitch 3 and the wheelbrace or the lever located under the 2nd row right rear passenger footwell (please refer to the information on the “Tool kit” in Section 5). B A C 1 3 5 2 Only use the front 1 and rear 4towing points (never use the driveshafts or any other part of the vehicle). These towing points may only be used for towing: never use them for lifting the vehicle directly or indirectly.
OPERATING FAULTS (1/6) Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or unlock the doors. Card battery is flat. Replace the battery. You can still lock/ unlock and start your vehicle (refer to the information on “Locking/unlocking the doors” in Section 1 and “Starting/Stopping the engine” in Section 2). Use of appliances operating on the same frequency as the card (mobile phone, etc.).
OPERATING FAULTS (2/6) The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights Battery terminals not tight, bat- Retighten or reconnect the terminals, or clean them are weak or fail to light up and the tery terminals disconnected or if they are oxidised. starter does not turn. oxidised. Discharged battery or not opera- Connect another battery to the faulty battery. Refer tional. to the paragraph “Battery: troubleshooting” in section 5 or replace the battery if necessary.
OPERATING FAULTS (3/6) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pressures, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved Dealer. White smoke from the exhaust. In the diesel version, this is not necessarily a fault. Smoke may be caused by particle filter regeneration. Please refer to the information on “Special features of diesel versions” in Section 2. Smoke under the bonnet.
OPERATING FAULTS (4/6) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The coolant temperature indicator is in the warning zone and warning light ® comes on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an authorised dealer as soon as possible.
OPERATING FAULTS (5/6) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Blown bulb. See information on “Headlights: changing bulbs” in section 5.
OPERATING FAULTS (6/6) Electrical equipment POSSIBLE CAUSES Traces of condensation in the lights. Traces of condensation may be a natural phenomenon caused by variations in temperature. WHAT TO DO In this case, the traces will disappear slowly once the lights are switched on. The front seat belt reminder light comes on when the seat belts are fastened. 5.36 An object is stuck between the floor and the seat and is disrupting the operation of the sensor.
Section 6: Technical specifications Vehicle identification plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine identification plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications . . . . . . . . . . . .
VEHICLE IDENTIFICATION PLATES A A 10 9 1 2 3 4 5 6 7 8 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. The presence and location of the information depends on the vehicle. B 6.2 Vehicle identification plate A 1 Manufacturer name. 2 EC design number or approval number. 3 Identification number. Depending on the vehicle, this information is also given on marking B. 4 MMAC (Maximum permissible all-up weight).
ENGINE IDENTIFICATION PLATES A 1 C 2 1 2 A 3 3 C A Please quote the information on the engine plate or label A in all correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. 6.
DIMENSIONS (in meters) 1,034 2,884 0,939 1,624 to 1,634 4,857 1,677* 1,615 to 1,625 2,128 * Unladen 6.
ENGINE SPECIFICATIONS Versions Engine type (see engine plate) Cubic capacity (cc) Type of fuel Octane rating 1.6 Tce 1.6 dCi M5M Turbo R9M 1 618 1 598 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap. If not available, for a limited time only, use unleaded fuel: Diesel The label located in the fuel filler flap indicates authorised fuels.
WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they may vary depending on your vehicle’s equipment. Consult an approved Dealer.
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
SERVICE SHEETS (1/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (2/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (3/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (4/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (5/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (6/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ALPHABETICAL INDEX (1/5) A ABS .......................................................................2.26 → 2.37 accessories........................................................................ 5.26 accessories socket ................................................... 3.28, 3.44 adaptive cruise control...........................................2.56 → 2.62 additional air conditioning ....................................... 3.12 – 3.13 additional methods of restraint .....................1.32 → 1.35, 1.
ALPHABETICAL INDEX (2/5) driver’s position .....................................................1.62 → 1.69 driving ......2.2 → 2.5, 2.10 → 2.20, 2.23 → 2.37, 2.46 → 2.48, 2.52 → 2.66, 2.74 → 2.79 driving aids ............................................................2.26 → 2.72 driving position settings ........................................................................ 1.28 driving recommendations ......................................2.16 → 2.20 E ECO driving ......................................
ALPHABETICAL INDEX (3/5) head-up display .....................................................1.70 → 1.73 headlight flashers .............................................................. 1.90 headlight washer ............................................................. 1.100 headrest............................................................................. 3.29 heating and air conditioning system ....................... 3.13 – 3.14 heating system ........................................................
ALPHABETICAL INDEX (4/5) Multi-Sense................................................................. 3.2 – 3.3 N navigation ............................................................... 3.43 – 3.44 navigation system ................................................... 3.43 – 3.44 O oil change ..................................................................... 4.4, 4.6 opening the doors ....................................................1.8 → 1.13 operating faults .......................................
ALPHABETICAL INDEX (5/5) sun visor ............................................................................ 3.22 sunroof...................................................................3.17 → 3.19 suspension ........................................................................ 2.73 suspension with controlled damping.................................. 2.73 switching on the vehicle ignition .......................................... 2.4 T tailgate ......................................1.15 → 1.19, 3.
( www.myrenault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
