KANGOO DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections ............................... 1 ................................................................... 2 Your comfort . ........................................................ 3 Maintenance 4 Getting to know your vehicle Driving .......................................................... Practical advice ..................................................... . ..................................... 6 ................................................
0.
Section 1: Getting to know your vehicle Key, radio frequency remote control: general information, use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Locking/unlocking the doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic locking when driving. . . . . . . . . . . . . . . .
Key, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) 2 3 1 Radio frequency remote control unit 1 Locking all the opening elements. 2 Unlocking all the opening elements. 3 Coded key for ignition switch, driver’s door and fuel filler cap. Driver’s responsibility Advice Avoid leaving the remote control in hot, cold or humid areas. The key must not be used for any function other than those described in the handbook (removing the cap from a bottle, etc.). 1.
Key, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surroundings: take care not to lock or unlock the doors by inadvertently pressing the buttons on the remote control. Interference Interference by factors in the immediate vicinity (external installations or the use of equipment operating on the same frequency as the remote control) may affect the operation of the remote control.
RADIO FREQUENCY REMOTE CONTROL/KEY: use The doors are locked and unlocked using the remote control unit. It is powered by a battery which must be replaced (refer to the information on the “Key, radio frequency remote control: batteries” in Section 5). Driver’s responsibility Never leave your vehicle with the key inside and never leave a child (or a pet) unsupervised, even for a short while.
DOORS (1/5) 2 3 1 Opening from the outside Unlock the door and pull handle 1. For information on unlocking the doors, refer to the information on the “Key, radio frequency remote control: use” in Section 1. Opening from the inside Lights-on reminder buzzer Child safety If the lights have been left on when the engine is switched off, an audible warning will sound when the door is opened (to prevent the battery discharging).
DOORS (2/5) Recommendations concerning the sliding side door 5 6 4 The following precautions must be taken when opening and closing the doors or any other opening element: – Check that the door will not come into contact with any person, animal or object. – Only use the handles on the inside and outside of the door to operate it. Sliding side door Opening from the outside Unlock the door and pull handle 4 then slide the door towards the rear of the vehicle until it locks in position.
DOORS (3/5) 7 Rear hinged doors Opening from the outside Unlock the door and pull handle 7. For information on unlocking the doors, refer to the information on the “Key, radio frequency remote control: use” in Section 1. 8 Opening the doors to the maximum position For each door, pull handle 8 to release the door check strap. Open the door as far as possible. Closing manually from the outside First close the small door and then close the large door.
DOORS (4/5) 10 9 Rear hinged doors (continued) Opening from the inside Pull handle 9 and open the door. Pull lever 10 to open the small door. Closing from the inside First close the small door and then close the large door. Position each door so that it is almost closed and then slam shut. Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time.
DOORS (5/5) 12 11 13 Tailgate Opening Unlock the door and pull handle 11. For information on unlocking the doors, refer to the information on the “Key, radio frequency remote control: use” in Section 1. For your safety, check that all the vehicle’s doors are properly closed before starting the engine. Closing Lower the tailgate using interior handles 12. When the tailgate reaches shoulder height, gently push it shut.
CENTRAL door locking/UNLOCKING (1/2) Locking the opening elements without the remote control 1 Control for locking and unlocking from the inside This enables all the doors to be locked simultaneously. Lock or unlock the doors by pressing switch 1. If a door or the tailgate is open or not closed properly, the doors and tailgate lock/unlock quickly. With the engine and ignition off, the sliding side doors closed and a front door open, press switch 1 for more than five seconds.
CENTRAL door locking/UNLOCKING (2/2) 2 Manual control Using the key Lock or unlock the driver’s door by inserting the key fully into lock 2, and turning the key. For more information on the remote controls, refer to the information on the “Key, radio frequency remote control: use” in Section 1. Locking the doors manually Turn screw 3 with the door open (using the end of the key) and close the door. This means that the doors are then locked from the outside.
Automatic locking when driving (RAID) Operating principle When the engine is started, the system automatically locks the doors when the vehicle reaches a speed of approximately 4 mph (7 km/h). Operating faults 1 You must first decide if you want to activate this function. To activate If you notice an operating fault (automatic locking impossible), first check that all doors are correctly locked. If they are correctly locked and the fault is still present, contact an approved Dealer.
FRONT HEADRESTS (1/3) 1 Insert the headrest rods in the holes, with the notches facing forwards (tilt the seat backwards if necessary). Pull tab 2 forwards and guide the headrest down to the required height. A 2 Headrest A To raise the headrest Pull it upwards to the required height. To lower the headrest Push tab 2 forwards and guide the headrest down to the required height. To remove the headrest Raise it to its highest position. Press button 1 and lift the headrest to release it.
FRONT HEADRESTS (2/3) To remove the headrest Raise it to its highest position. Press button 4 and lift the headrest to release it. Note: when the headrest is removed, take care not to change the positions of the rods. B 3 To refit the headrest 4 Headrest B To raise the headrest Pull it upwards to the required height. To lower the headrest If the setting of the rods has been altered, pull them fully upwards.
FRONT HEADRESTS (3/3) To refit the headrest Press tab 5. 5 C Insert the headrest rods in the holes with the notches facing forward, and guide the headrest down to the required height. 6 Headrest C To raise the headrest Pull it upwards to the required height. To lower the headrest Press tab 5 and guide the headrest down to the desired height. To remove the headrest Raise it to its highest position. Press tabs 5 and 6 then lift the headrest to release it.
REAR HEADRESTS 1 To raise it Slide it to the required height. To lower it Pull it towards you and slide it to the required height. 2 Storage position 2 Pull it towards you and lower it completely. When the headrest is fully lowered, it is in the storage position: do not use this position when someone is sitting in the rear seats. To remove it Raise the headrest then press tabs 1 to release it. To refit it Press tab 1 and insert the rods into the holes, with the notches facing forwards. 1.
Front seats (1/3) 2 2 1 3 To move forwards or backwards Depending on the seat, lift bar 1 or handle 4 to release it. Release the handle at the desired position and make sure that it is locked. Adjusting the height of the driver’s seat Move lever 3 as many times as necessary: – upwards to raise the seat, – downwards to lower the seat. 4 To tilt the seatback Depending on the seat, lower or lift lever 2 and tilt the seatback until it reaches the required position.
Front seats (2/3) 5 4 2 2 Flat position Depending on the vehicle, the seatback on the passenger side may be folded down onto the seat base to create a flat position. – Hold handle 4 and move the seat as far back as possible; – lower the headrest fully; – hold the top of the seatback to lower it; – pull lever 2 and pull the seatback down and forwards (the seat base will be positioned on the floor); For safety reasons, carry out any adjustments when the vehicle is not being driven. 1.
Front seats (3/3) 6 Front seats Operating faults (depending on vehicle) If the sliding side door does not work, lower handle 6, hold it while the seatback tilts and slide the seat forwards. To place the seat into the comfort position, slide it rearwards. Adjust the seat and make sure that it is correctly locked. For safety reasons, carry out any adjustments when the vehicle is not being driven. To avoid all risk of injury, ensure that nobody is in the proximity of the moving parts.
Roof flap (1/2) Note: when driving with the roof flap open, you may hear air noises. To reduce these, open one of the side windows slightly. 1 2 3 To open: Transverse bar – Unlock the control 2, the roof flap lifts automatically (ensure that nothing stops the flap from opening.
Roof flap (2/2) 1 2 To close: – Unlock the control 2, the roof flap automatically opens halfway; – pull the handle 1 and lock the roof flap in the closed position. Before starting, always reposition the transverse bar and ensure it is correctly locked. The rear hinged doors can only be closed with the bar locked. Remember that the overall vehicle dimensions may change when you are transporting bulky objects. 1.
swivelling PARTITION 2 3 4 1 5 To rotate the partition – Unlock the seat base by moving handle 1 downwards; – lift the front passenger seat base vertically (arrow); – unlock the swivelling section by lifting catch 3; – Pivot the moving section 90 degrees, lock it at point 5 and lower catch 3. – reposition the seat base, proceeding in reverse order. Note: before refitting the swivelling section in its original position, check that locking point 4 is clean.
Seat belts (1/4) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belt to ensure optimum protection. Adjusting your driving position Make sure that the rear bench seat is locked in position correctly so that the rear seat belts will operate efficiently.
Seat belts (2/4) tened. An audible warning sounds at a low volume for 30 seconds, then at a high volume for 90 seconds. Unfastening Press button 4 and the seat belt will be rewound by the inertia reel. Guide the belt. 1 3 5 5 4 Locking Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pulling on buckle 3). If the belt jams, allow it to return slightly before attempting to unwind it again.
SEAT BELTS (3/4) Rear side seat belts The belts are locked, unlocked and adjusted in the same way as the front belts. 7 8 7 Rear centre belt Slowly unwind the belt until buckle 7 clicks into catch 8. Make sure that the rear bench seat is locked in position correctly so that the rear seat belts will operate efficiently. Refer to the information on the “Rear bench seat: functions” in Section 3. 1.
SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. For special operations (e.g. fitting child seats) contact an approved Dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
Methods of restraint in addition to the front seat belts (1/3) Depending on the vehicle, they are composed of: – seat belt pretensioners; 1 2 – air bags 1 for driver and front passenger. – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. These systems are designed to act independently or together when the vehicle is subjected to a frontal impact.
Methods of restraint in addition to the front seat belts (2/3) Air bags for driver and front passenger It is fitted to the front seats on the driver’s side and, depending on the vehicle, on the passenger’s side as well. Depending on the vehicle, the presence of this equipment is indicated by the word “air bag” on the steering wheel and dashboard (air bag zone A) and a symbol on the lower section of the windscreen.
Methods of restraint in addition to the front seat belts (3/3) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
Side PROTECTION devices Side air bags (depending on vehicle) This air bag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Curtain air bags (depending on vehicle) These air bags may be fitted along the top of each side of the vehicle and are triggered along the front and rear side windows to protect the passengers in the event of a severe side impact.
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. 1 The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
Child safety: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
Child safety: choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position for as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. 1.
child safety: choosing a child/baby seat mounting (1/2) The are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
child safety: choosing a child/baby seat mounting (2/2) 5 4 1 2 3 3 The two rings 1 are located between the seatback and the seat base, behind the zip fasteners, and are identified by a marking. To ensure your child seat can be easily fitted and locked on rings 1, use access guides 2 on the child seat. The third ring is used to attach the upper strap on some child seats. Depending on the vehicle, pass the strap between wheel arch liner 4 and the underside of upper partition 5.
Child safety: Fitting a child seat (1/5) Some seats are not suitable for fitting child seats. The diagrams on the following pages show you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
Child safety: Fitting a child seat (2/5) Van version Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt. ² ³ seats. Seat not suitable for fitting child Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. (1) B efore fitting a child seat: position the vehicle seat as far back as possible.
Child safety: Fitting a child seat (3/5) Sport tourer versions Child seats attached using the ISOFIX mounting ü ³ Seat which allows an ISOFIX. child seat to be fitted. Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. ² ± seats. Child seat attached using the belt ¬ Seat which allows a seat with “Universal” approval to be fitted using a seat belt; − Seat which only allows a rearfacing seat with “Universal” approval to be attached with a seat belt.
Child safety: Fitting a child seat (4/5) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
Child safety: Fitting a child seat (5/5) X =S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be attached by seat belt; check that it can be fitted. IUF/IL = On equipped vehicles, seat which allows a child seat with “Universal, Semi-universal or Vehicle-specific” approval to be fitted using the ISOFIX system. Check that it can be fitted.
child safety: deactivating/activating the front passenger air bag (1/3) 2 1 Deactivating the front passenger air bags (on equipped vehicles) You must deactivate the devices in addition to the front passenger seat belt before fitting a child seat in the front passenger seat. To deactivate the air bags: with the vehicle stopped and the ignition off, press and turn lock 1 to the OFF position.
child safety: deactivating/activating the front passenger air bag (2/3) A A 3 The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered. 1.
child safety: deactivating/activating the front passenger air bag (3/3) 2 DANGER 1 Activation of the front passenger air bag You should reactivate the air bag as soon as you remove the child seat from the front passenger seat to ensure the protection of the front passenger in the event of an impact. To reactivate the air bags: with the vehicle stopped and the ignition off, press and turn lock 1 to the ON position. With the ignition on, you must ensure that warning light 2 is off.
STEERING WHEEL 1 Steering wheel height adjustment Pull lever 1 and adjust the steering wheel to the required position; push the lever to lock the steering wheel. Make sure that the steering wheel is correctly locked. For safety reasons, only adjust the steering wheel when the vehicle is stationary. Never leave the steering wheel on full lock when the vehicle is stationary. Never switch off the ignition when travelling downhill, and avoid doing so in normal driving (assistance is not provided). 1.
Driving position: left-hand drive (1/2) 1 27 26 3 2 25 24 4 23 5 6 7 22 16 21 17 20 19 1.
Driving position: left-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Stalk for: – direction indicator lights, – exterior lights, – front fog lights, – rear fog lights. 2 – Horn, – location for driver’s air bag. 3 Instrument panel. 4 Stalk for: – wipers, – windscreen washer, – trip computer and warning system. 5 Ignition switch.
Driving position: right-hand drive (1/2) 1 2 3 29 1.
Driving position: right-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side window demister outlet. 2 Side air vent. 3 Speaker. 4 Location for passenger air bag. 5 Windscreen demister outlet. 6 Controls for ventilation, heating and de-icing. 7 Centre air vent. 8 Central display: – seat belt reminder warning light, – air bag deactivation warning light, – navigation, – clock, – exterior temperature.
instrument panel: warning lights (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A Instrument panel A Warning light ® requires you to stop immediately, for your own safety, as soon as traffic conditions allow. Switch off the engine and do not restart it. Contact an approved Dealer. 1.50 á k g f d Main beam headlight tell-tale light U Dipped beam headlight telltale This lights up when the ignition is switched on and goes out after a few seconds.
Instrument panel: warning lights (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Ô A Coolant temperature warning light If this remains lit while driving accompanied by the ® indicator light, it indicates engine overheating. Stop and allow the engine to run at idle speed for a minute or two. The temperature should drop. If not, stop the engine. Let the engine cool down, then check the coolant level. Contact an approved Dealer if necessary.
Instrument panel: warning lights (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. É A Preheating warning light (on diesel version) This should come on when the ignition is switched on. It indicates that the heater plugs are in operation. It goes out after preheating is sufficient and the engine can be started.
Instrument panel: warning lights (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ù Electronic Stability Program (ESP) and Traction control system (ASR) indicator light. A The indicator light may come on for several reasons: refer to the information on the “Electronic stability program: E.S.P. ” and “Traction control: A.S.R.” in Section 2.
instrument panel: display and indicators (1/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. 1 2 Speedometer 1 Overspeed buzzer Depending on the vehicle, a beep sounds for 10 seconds approximately every 40 seconds as long as the vehicle is travelling at over 72 miles per hour (120 km/h). Note: depending on the vehicle, the desired speed may be programmed; consult an approved Dealer. 1.
instrument panel: display and indicators (2/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. Coolant temperature indicator 4 or A 3 4 In normal use, the needle should be positioned before zone B. Under “intensive” operating conditions, the needle may approach this zone. The only warning is if the indicator light comes on or the message “engine overheating” appears. A B Fuel gauge A Fuel gauge 3 The number of squares lit shows the fuel level.
instrument panel: display and indicators (3/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. – Display selection 5 Press briefly to move from the total mileage to the trip mileage and vice versa. –Resetting the trip mileage recorder Once trip mileage has been selected on the display, press and hold the button. Multifunction display A 6 Total mileage recorder. Trip mileage recorder. Setting the time.
TRIP COMPUTER: general information (1/2) c) mileage before service; 1 Trip computer and warning system A Display selection keys 1 and 2 Depending on the vehicle, this includes the following functions: Scroll through the following information upwards (button 1) or downwards (button 2) by pressing briefly and successively (the display depends on the vehicle equipment and country).
TRIP COMPUTER: general information (2/2) 1 2 Trip mileage resetting With “trip mileage recorder” selected on the display, press button 1 or 2 until the mileage recorder resets to zero. Resetting the journey parameters (reset button) With one of the journey parameters selected on the display, press button 1 or 2 until the display resets. 1.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections 37360 KM 7080 KM FUEL USED 26.0 L Interpreting the display selected a) Total mileage and trip mileage recorder b) Journey parameters Fuel consumed since the last reset. AVERAGE 7.3 L/100 Average fuel consumption since the last reset.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected CURRENT 8.6 L/100 Current fuel consumption RANGE 402.0 KM Estimated range with remaining fuel This value is displayed after a speed of approximately 20 mph (30 km/h) is reached. This range takes into account the average fuel consumption since the last time the reset button was pressed.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections SERVICE IN 137.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected SPEED LIMITER 70 KM/H d) Cruise control/speed limiter programmed speed (depending on the vehicle). Refer to the information on the “Cruise control/speed limiter” in Section 2. CRUISE CONTROL 70 KM/H 1.
TRIP COMPUTER AND WARNING SYSTEM: information messages Information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpretation of messages e) On-board log “NO MESSAGE AVAILABLE” “BOOT OPEN” “BATTERY MODE:ECONOMY” “OIL LEVEL CORRECT” “AUTO LIGHTS DEACTIVATED” Successive display: – of information messages (automatic lighting, etc.
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an approved Dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given on the following pages.
TRIP COMPUTER AND WARNING SYSTEM: warning message These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Clock and exterior temperature Exterior temperature A 1 2 B 3 With the ignition on, the time and, depending on the vehicle, exterior temperature are displayed. After two seconds, the hours and minutes start flashing. Setting the time When only the hours flash, press the top button to scroll through them. Setting clock A On equipped vehicles, adjustment buttons 1 and 2 are used to set the clock. Press button 1 to adjust the hours and button 2 to adjust the minutes.
Rear-view mirrors 3 B A 1 Interior rear view mirror The interior rear view mirror is adjustable. When driving at night, tilt lever 1 to avoid being dazzled by the headlights of the vehicle behind. C 2 D Door mirrors with electrical adjustment With the ignition on, turn button 2: – position A to adjust the left-hand door mirror; – position C to adjust the right-hand door mirror. B is the inactive position. Door mirrors with manual adjustment To adjust the door mirror, move switch 3.
AUDIBLE AND VISUAL SIGNALS 1 1 0 2 Horn Press at one of the locations 2. Headlight flasher Pull stalk 1 towards you to flash the headlights. 1.68 3 é Hazard warning lights Direction indicators Press switch 3. This device simultaneously activates the four direction indicators and the side indicator lights.
EXTERNAL LIGHTING AND SIGNALS (1/3) k 1 2 Dipped beam headlights Manual operation Turn the end of stalk 1 until the symbol is opposite mark 2. This indicator light on the instrument panel comes on. Automatic operation (depending on vehicle) 3 u Side lights Turn the end of stalk 1 until the symbol is opposite mark 2. The instrument panel will light up. á Main beam headlights With stalk 1 in dipped beam headlights position, move the stalk towards you.
EXTERNAL LIGHTING AND SIGNALS (2/3) “See-me-home lighting” function 1 (depending on vehicle) This function (useful, for example, when opening a gate, garage, etc.) enables you to switch the dipped headlights on momentarily. 2 With the ignition off and the headlights off, pull stalk 1 towards you: the dipped beam headlights come on for approximately sixty seconds. This action may be carried out no more than four times for a maximum lighting period of four minutes.
External lighting and signals (3/3) 1 4 f Rear fog light The front fog lights and the side lights or dipped beam headlights must be on. Turn ring 5 on stalk 1 until the symbol is opposite mark 4, then release it. This indicator light on the instrument panel comes on. 5 To avoid inconveniencing other road users, remember to switch off the rear fog light when it is no longer needed.
Electrical adjustment of the dipped beam headlights 1 A Control knob 1 is used to adjust the height of the headlight beams according to the load. Turn control knob 1 downwards to lower the headlights and upwards to raise them. Unladen, control knob 1 should be at 0. When the vehicle is partially or completely laden, the headlight beam should be set to light the road at between 50 and 100 metres. Then use positions 1 to 4 on the control knob. 1.
FRONT WINDSCREEN WASHER/WIPER (1/2) Automatic wiper function (depending on vehicle) With the engine running, move stalk 1. 1 A Park A B C D 2 Windscreen wiper With the ignition on, move stalk 1 around the steering wheel: A Park B Intermittent wiping The wipers will pause for several seconds between sweeps. It is possible to change the time between sweeps by turning ring 2. Special note When the vehicle is being driven, the wiping speed slows down whenever the vehicle stops.
FRONT WINDSCREEN WASHER/WIPER (2/2) 1 Windscreen wiper With the ignition on, pull stalk 1 towards you. A brief pull will trigger a single sweep of the wipers, in addition to the windscreen washer. A longer pull will trigger three sweeps of the wipers followed, a few seconds later, by a fourth, in addition to the windscreen washer.
REAR WINDSCREEN WASHER/WIPER p 1 Rear screen wash/wipe (depending on vehicle) Turn the end of stalk 1 to position the symbol opposite mark 2. When the stalk is released, it returns to the rear screen wiper position. 2 Y timer Speed-dependent rear screen wiper with (depending on vehicle) Turn the end of stalk 1 to position the symbol opposite mark 2. Wiping frequency varies with speed. Check the condition of the wiper blades.
FUEL TANK (1/2) Fuel grade Use a high-grade fuel that complies with the legislation in force in each country. It must conform to the specifications given on label A inside the fuel filler flap. Please refer to the information on “Engine specifications” in Section 6. B A 1 2 Diesel versions It is essential to use diesel fuel that conforms to the specifications given on the label inside fuel filler flap A. Make sure that no water accidentally enters the fuel tank during filling.
FUEL TANK (2/2) Petrol versions It is essential to use unleaded petrol. The octane rating (RON) should match the information given on the label A located inside the fuel filler flap. Please refer to the information on “Engine specifications” in Section 6. Vehicles running on ethanol-based fuel It is essential to use unleaded petrol or fuel containing a maximum of 85% ethanol (E85). In very cold conditions, it may be very difficult or even impossible to start the engine.
1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ignition switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting/stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN/IGNITION SWITCH Running in Ignition on position M The ignition is switched on: Petrol version – petrol version: you can start the vehicle; For the first 600 miles (1,000 km) do not exceed 54 mph (90 km/h) in the highest gear. – diesel version: the engine is preheating. After 600 miles (1,000 km), you may use your vehicle normally, although you may only expect top performance after approximately 1,800 miles (3,000 km).
Starting/STOPPING THE ENGINE É Diesel versions Turn the ignition key to the “Ignition on” position M, and hold this position until the engine preheating light goes off. Stopping the engine With the engine idling, turn the key to the “Stop” position St. Turn the key to starter position D without depressing the accelerator pedal. Release the key as soon as the engine starts.
Gear lever 1 When stationary and depending on the slope and/or vehicle load, it may be necessary to pull up the handbrake at least two extra notches and engage a gear (1st or reverse gear) for vehicles with a manual gearbox or position P for vehicles with an automatic transmission. Selecting reverse gear (vehicle stationary) Vehicles with manual gearbox: follow the grid drawn on knob 1, and depending on the vehicle, lift ring against the gear lever knob to select reverse.
Handbrake/Power-assisted steering To apply: Pull upwards, check that the vehicle is properly immobilised. 1 2 Variable power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).
Special features of petrol versions The following operating conditions should be avoided: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed As a guide, this type of cleaning should take up to 20 minutes. Diesel engines are fitted with an injection pump with an electronic regulator which prevents overrevving of the engine irrespective of the gear engaged. If the © warning light comes on, contact an approved Dealer as soon as possible. When driving, depending on the fuel grade used, it is possible that white smoke may be emitted.
Advice: antipollution, fuel economy and driving (1/3) Your vehicle complies with criteria for recycling and recovering vehicles at the end of their service life which will come into force in 2015. Some parts of your vehicle have therefore been designed to facilitate future recycling. These parts are easy to remove so that they can be recovered and reprocessed by recycling companies.
Advice: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring system – Do not overrev the engine in the intermediate gears. Always use the highest gear possible without labouring the engine. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level. Keep your foot in the same position on the accelerator pedal. – Double declutching and accelerating before switching off are unnecessary in modern vehicles.
Advice: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the Renault eco² group signature.
Driving correction devices (1/3) Depending on the vehicle, this is composed of: – ABS (anti-lock braking system); – electronic stability program (ESP) with understeer control and traction control (ASR); – emergency brake assist with, depending on the vehicle, braking anticipation; These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions. However, the functions do not take the place of the driver.
Driving correction devices (2/3) Electronic stability program (ESP) with understeer control and traction control (ASR) This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
Driving correction devices (3/3) 1 The traction control (ASR) offers additional safety, it is recommended that you do not drive with the function disabled. Correct this as soon as possible by pressing switch 1 again. Hazard warning lights switching on Depending on the vehicle, these may light up in the event of sudden deceleration. Note: The function is reactivated automatically when the ignition is switched on or when a speed of approximately 24 mph (40 km/h) is exceeded.
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) 1 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. 2 3 4 5 Controls Switching on 1 Main “On/Off” switch. Press switch 1 on the side showing . The indicator light comes on, lit orange, and the message “speed limiter” appears on the instrument panel, accompanied by dashes to indicate that the speed limiter function is activated and waiting to store a limit speed.
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by repeatedly pressing: It is possible to exceed the limit speed at any moment. To do this: press the accelerator pedal firmly and fully (beyond the kickdown point). – switch 2 (+) to increase the speed; – switch 3 (-) to decrease the speed. 2 3 4 5 Whilst the speed is being exceeded, the cruising speed displayed on the instrument panel flashes.
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been stored, it can be recalled by pressing switch 5 (R). 2 3 4 1 5 Putting the function on standby Switching off the function The speed limiter function is interrupted when you press switch 1. In this case, the speed is no longer stored. The instrument panel orange indicator light goes out to confirm that the function is deactivated.
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) 1 2 3 4 5 This function is an additional driving aid. However, the function does not take the place of the driver. The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h).
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) 1 2 6 Switching on Press switch 1 on the side showing . Indicator light 6 comes on, lit green, and the message “cruise control” appears on the instrument panel, accompanied by dashes to indicate that the cruise control function is activated and waiting to store a cruising speed.
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelerator pedal. While it is being exceeded, the cruising speed flashes on the instrument panel. 2 3 4 5 Then, release the accelerator: after a few seconds, the vehicle will automatically return to its set cruising speed.
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Recalling the cruising speed 2 3 4 5 If a speed has been stored, it is possible to recall it by pressing button 5 (R), on condition that you are driving faster than 20 mph (30 km/h) and that you are sure that the road conditions are suitable (traffic, road surface condition, weather conditions, etc.).
Automatic gearbox (1/3) Driving in automatic mode A Move lever 1 to position D. 1 2 3 Selector lever 1 Operation Display A on the instrument panel shows the mode and gear selected. With the gear lever in position P or N, switch on the ignition. P: park With your foot on the brake pedal (warning light 3 goes out), shift from position P. R: reverse N: neutral D: automatic mode (in forwards gear only) 2: displays gear engaged in manual mode. 2.
Automatic gearbox (2/3) Operating faults Driving in manual mode With the selector lever 1 in position D, move the lever to the left. Shifting the lever repeatedly allows you to change gears manually: – To move down through the gears, push the lever backwards; – To move up through the gears, push the lever forwards. The gear selected is displayed on the instrument panel. Special cases In certain driving conditions (eg.
Automatic gearbox (3/3) – Vehicles not fitted with traction control: on a slippery surface or surface with a low level of adhesion, select second gear manually before starting the engine to avoid wheelspin when starting. Parking the vehicle 4 Special circumstances – Snow position: if you are driving on ground where you are likely to skid (snow, mud, etc.), press switch 4, and operating tell-tale 5 will come on.
PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic sensors, fitted in the vehicle’s rear bumper, measure the distance between the vehicle and an obstacle when reversing. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 25 centimetres from the obstacle.
PARKING DISTANCE CONTROL (2/2) Prolonged deactivation of the system You can deactivate the system permanently by pressing and holding switch 1. The warning light built into the switch remains lit constantly. 1 Temporary deactivation of the system (depending on vehicle) Press switch 1 to deactivate the system. The indicator light built into the switch lights up to remind you that the system is deactivated. Pressing the switch again will reactivate the system and switch off the indicator light.
Section 3: Your comfort Air vents: air outlets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heating/air conditioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air conditioning: information and advice on use . . . .
Air vents: air outlets (1/2) 1 2 3 6 4 2 5 1 6 1 Demister outlets, side windows. 4 Centre air vents. 2 Side air vents. 5 Control panel. 3 Demisting outlets for the windscreen. 6 Footwell air vents. 3.
Air vents: air outlets (2/2) To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. 7 9 10 8 Centre air vents Side air vents Settings Settings Air flow: Air flow: Move control knob 7 (beyond the point of resistance). Move control knob 10 (beyond the point of resistance). Air distribution: Air distribution: Right/left: move tabs 8. Right/left: move tab 9. Up/down: guide the air vent up or down.
HEATING/AIR CONDITIONING (1/3) 2 1 3 4 Switching air conditioning on or off The air conditioning is switched on (indicator light illuminated) or off (indicator light extinguished) using button 6. The air conditioning system is used for: – lowering the temperature inside the passenger compartment; – eliminating condensation more quickly. 6 The controls 1 -A ir recirculation control. 2 -A djusting the air temperature. 3 -A djusting the ventilation speed.
HEATING/AIR CONDITIONING (2/3) 4 ó G The air flow is directed mainly towards the footwells. The air flow is directed to all air vents and the footwells. This is the recommended position for the best temperature in hot weather. J The air flow is directed mainly to the dashboard vents. This position allows the passenger compartment to be heated or cooled more quickly.
HEATING/AIR CONDITIONING (3/3) Adjusting the ventilation speed 3 1 Normal use Turn control 3 to one of the four positions to start the ventilation system and adjust the power. Select position 1 for minimum ventilation and position 4 for maximum ventilation.
AUTOMATIC CLIMATE CONTROL (1/8) 1 2 3 4 5 6 7 12 8 11 10 9 Controls (depending on vehicle) 8 and 10 - A djusting the ventilation speed. 1 – Clear View button to demist and de-ice the windows. 11 - Heated rear screen and heated door mirror de-icing. 2 - Switching off air conditioning. 12 - Air recirculation control. 3 and 6 - Adjusting the air tempera ture. Information and advice for use 4 - Display. Refer to information on “Air conditioning: information and advice on use”.
AUTOMATIC CLIMATE CONTROL (2/8) 3 5 6 Only the temperature and the AUTO symbol are displayed Functions managed in automatic mode are not displayed. – press button 6 to increase the temperature; – press button 3 to decrease the temperature. Note: The maximum and minimum settings of 15°C and 27°C allow the system to produce a minimum or maximum temperature, whatever the ambient conditions. Automatic mode Press button 5. The AUTO operating tell-tale will come on.
AUTOMATIC CLIMATE CONTROL (3/8) Adjusting automatic mode The system normally operates in automatic mode but you can alter the standard settings used by the system (air distribution, etc.). These options are explained on the following pages. The displayed temperature values show a comfort level. When starting the engine, increasing or decreasing the value displayed will not allow the comfort level to be reached any more quickly.
AUTOMATIC CLIMATE CONTROL (4/8) 4 5 7 ô The air flow is directed mainly to the dashboard air vents. This position allows the passenger compartment to be heated or cooled more quickly. ö F The air flow is directed to all the windscreen demisting vents and the passenger footwells. wells. Distribution of air in the passenger compartment There are five possible combinations for air distribution, which may be selected by pressing buttons 7 and 9 repeatedly.
AUTOMATIC CLIMATE CONTROL (5/8) Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. 2 4 5 Automatic mode is switched off by pressing buttons 8 and 10. These buttons allow you to increase or decrease ventilation speed. 8 Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions.
AUTOMATIC CLIMATE CONTROL (6/8) 11 Rear screen de-icing/ demisting Press button 11. This function allows rapid electric demisting of the rear screen and, depending on the vehicle, electric de-icing of the door mirrors. 3.12 To exit this function, press button 11 again. Demisting automatically stops by default.
AUTOMATIC CLIMATE CONTROL (7/8) 1 Note: if you wish to reduce the air flow (which may produce a certain amount of noise in the passenger compartment), press button 10. 5 To exit this function, press: – button 1 again; – or button 5 (the AUTO indicator light on the display will light up). 11 Clear View function Press button 1. The AUTO button indicator light (on the display) goes out. 10 This function rapidly demists/de-ices the windscreen, the front side windows and the door mirrors.
AUTOMATIC CLIMATE CONTROL (8/8) 12 Air recirculation Pressing button 12 activates air recirculation (the symbol lights up on the display). During recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle. Air recirculation allows the external atmosphere to be cut off (when driving in polluted areas, etc.). 3.14 Prolonged use of the air recirculation mode may cause the windows to mist up or lead to odours, as the air is not renewed.
AIR CONDITIONING: information and advice on use Fuel consumption You will normally notice an increase in fuel consumption (especially when driving in town) when the air conditioning is operating. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Advice for reducing consumption and helping to preserve the environment Drive with the air vents on and the windows closed.
Interior lighting (1/2) 1 3 2 Courtesy lights Switches 1 or 3 provide: – permanent lighting; – intermittent lighting, which comes on when a door is opened. It goes out when the doors concerned are properly closed; 4 A Map reading lights Luggage compartment light A Tilt the switch 3 for permanent lighting. Tilt the switch 4 for permanent lighting. (depending on vehicle) (depending on vehicle) In the front passenger seat, press switch 2. – immediate switching off.
Interior lighting (2/2) Special features Depending on the vehicle, remote unlocking of the doors triggers timed lighting of the passenger compartment. If one of the front or rear doors is opened, the period for which the light is switched on will start again. C B 5 Then the courtesy light and the luggage compartment light dim and go out.
Sun visor/Mirrors 1 3 2 Front sun visor Lower sun visor 1. The clip can be used to hold motorway passes, etc.. Courtesy mirror 2 Child minder mirror 3 If the sun visor is fitted with a courtesy mirror, it has a cover. The child minder mirror allows you to keep an eye on your child in the back seat. (passenger side) When driving, ensure the courtesy mirror cover is closed. Risk of injury. 3.
electric WINDOWS (1/2) 1 5 4 6 2 7 3 Electric windows With the ignition on: – press the switch for the window concerned to lower it to the desired height; – lift the switch for the window concerned to raise it to the desired height. From the driver’s seat Operate the switches as follows: – 1 for the driver’s side; – 2 for the front passenger’s side; – 3 and 5 for the rear passenger windows. From the front passenger seat From the rear seats Press switch 6. With the doors closed, press switch 7.
electric WINDOWS (2/2)/Half-opening window 1 8 9 8 One-touch electric window Manual window winders Half-opening window The one-touch mode works in addition to the operation of the electric windows described previously. Turn handle 8. To half-open the window, turn handle 9 in the direction of the arrow then lock it by pushing the handle. When closing it, check that it is properly locked. It is fitted to the driver’s window and is used for lowering only.
MANUAL SUNROOF Precautions during use – check that the sunroof is properly closed before leaving your vehicle; 1 – clean the seal every three months using products recommended by our Technical Department; – do not open the sunroof immediately after the vehicle has been in the rain or after your car has been washed. – Vehicle with roof bars 2 Opening Closing To the first position Hold tab 2 pressed in and return the handle 1 to the initial position.
Ashtrays/Cigar lighter/Accessories sockets 3 1 4 3 2 Removable ashtray 1 Cigar lighter 2 Accessories sockets This is a removable ashtray which can be placed in the cup holders 3. With the ignition on, press it in. It will spring back with a click when it is ready. Pull it out to use. You may use the cigar lighter recess 2 or one of sockets 4 (depending on the vehicle).
Passenger compartment storage space and fittings (1/5) 4 1 3 2 Glovebox To open the glove box, lift catch 1. Audio connection socket 2 If fitted to the vehicle, this socket is used for connecting a portable audio player. Dashboard storage compartment 3 Central storage compartment 4 To open it, lift cover 5. It will store a 1.5 litre bottle. 5 When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged.
Passenger compartment storage space and fittings (2/5) 7 6 8 9 Front door storage compartments 6 Sliding side door storage compartment 8 Bottle holder 7 Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. 3.24 Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning or braking.
Passenger compartment storage space and fittings (3/5) 10 11 12 13 Front upper cab storage compartment 10 Central upper storage compartments 12 Do not use it for getting into or out of the vehicle and do not hang from it. To open the storage compartments, pull handles 13. Sunglasses holder 11 This is not suitable for storing heavy items. There is a dedicated storage compartment in the centre. Do not hang any heavy and/or sharp objects which may fall whilst driving. Risk of injury.
Passenger compartment storage space and fittings (4/5) 16 14 15 Trays on the front seat 14 Permitted weight: 5 kg, evenly distributed. Front seat pockets 15 Flaps 16 in the rear passenger footwells (depending on vehicle) These compartments can hold road maps, manuals, cloths, etc. 3.
Passenger compartment storage space and fittings (5/5) 17 17 17 Clothes hook 17 Depending on the vehicle, a hook may be located on the partition behind the front passenger seat. For safety reasons, this hook may only be used to hang clothes. Note: the maximum permitted load is 4 kg. 3.
Rear bench seat: functions (1/2) For safety reasons, carry out any adjustments when the vehicle is not being driven. 1 When moving the rear bench seat, make sure the bench seat anchorage points are clean (they should be free from grit, cloths etc.). To fold down the seatback To raise the seatback Before moving the bench seat, make sure the front seats are pushed forward enough, that the rear seat belts are unfastened and that nothing will obstruct the manoeuvre.
Rear bench seat: functions (2/2) Use restriction It is forbidden to drive with a seatback or a front seat folded down when there is a passenger occupying a rear seat. For safety reasons, carry out any adjustments when the vehicle is not being driven. 3.
Transporting objects in the luggage compartment Always position the objects transported so that the largest surface is against: – the rear bench seatbacks, for normal loads; – the front seats for maximum loads. Always position the heaviest items directly on the floor. Always position the heaviest items directly on the floor. Use the lashing points on the floor of the luggage compartment, if these are fitted to the vehicle.
LUGGAGE COVER 2 A 1 C B The luggage compartment cover is made up of two rigid sections. – The storage position C (depending on the vehicle). There are three possible positions: To store the luggage compartment cover, position it in the runner against the rear bench seatback. – top position A; – bottom position B (depending on the vehicle). In both cases, you can fold section 1 onto section 2 by lifting it as shown by the arrow.
Luggage NET 1 1 2 The luggage net (depending on vehicle) This is located in the luggage compartment. It may be attached behind the front seats or behind the rear bench seat. Hooks 1 may also be used to hang clothes. 3.32 3 Positioning the net 2 – Upper section: insert the tabs at the ends of the net in hooks 1; – lower section: engage belts 3 in lashing rings 4 on the floor. Ensure that both forks of the lower hook are engaged; – tighten the net using the tensioning units.
Roof bars (1/2) A 2 B 1 To place the bars in the transverse position – Unclip levers 1. – Lift the bars to allow them to be pivoted (figure A). – Lock the bars in the transverse position (figure B). – Check that they are correctly locked. Maximum weight on each roof bar: 40 kg evenly distributed (80 kg over 2 roof bars) It is strictly forbidden to place the roof bars in the transverse position (carrying position) when entering a roller-type car wash. 3.
Roof bars (2/2) C 2 3 To slide the bar Roof bar 2 can be slid to move it closer to or further from the other bar (figure C). There are two positions: centre or rear. With the bar unlocked, pull it towards the front or the rear of the vehicle to slide it in rail 3. Once you have chosen the position, pivot the bar and lock it in the transverse position (figure D). Check that both bars are correctly locked in position. 3.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . topping up/filling. . . . . . . . . . . . . . . . . . .
Bonnet 3 4 5 2 1 Opening Closing Pull control 1 towards you. Check that nothing has been left in the engine compartment. Lift the bonnet by several centimetres and push lever 2 to the left. Lift the bonnet up and release stay 4 from its holder 5. For your own safety, it is very important to fit the stay into its retainer 3. Check that it is correctly locked.
Engine oil level: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. 1 However, contact an approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
Engine oil level: general information (2/2) B A Maximum engine oil level exceeded. B A The oil level should only be read with the dipstick as explained above. If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer.
Engine oil level: topping up/filling (1/2) 4 5 4 4 5 5 Topping up/filling – Unscrew cap 4; The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). – top up the level (as a guide, the capacity between the minimum and the maximum reading on the dipstick 5 is 1.
Engine oil level: topping up/filling (2/2)ENGINE OIL CHANGE Oil change Service interval: refer to the Maintenance Service Booklet for your vehicle. Average capacities for oil change including oil filter (for information) 1.6 16V engine 1.6 engine 1.5 dCi engine Filling: take care when topping up the oil that no oil drips onto engine components - risk of fire. Remember to refit the cap securely as there is a risk of fire if oil splashes onto hot engine components. : 4.8 litres : 3.3 litres : 4.
Levels (1/3) 1 Level 1 Topping up It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI" warning line. After any operation on the hydraulic circuit, a specialist must replace the fluid. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website. Only use fluids approved by our Technical Department (and taken from a sealed container).
Levels (2/3) Checking intervals Replacement intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). Refer to the Maintenance Service Booklet for your vehicle. If the level needs to be topped up, only use products approved by our Technical Department which ensure: 2 – protection against freezing; – anticorrosion protection of the cooling system.
LEVELS (3/3)FILTERS Liquid Screen wash product (product with antifreeze in winter). Jets To adjust the height of the windscreen washer jets, use a tool such as a flatblade screwdriver. Filters The replacement of filter elements (air filter, cabin filter, diesel fuel filter, etc.) is scheduled in the maintenance operations for your vehicle. Replacement intervals for filter elements: refer to the Maintenance Service Booklet for your vehicle.
Battery 1 It does not need to be serviced; never open cover 1 on the battery. Handle the battery with care as it contains sulphuric acid, which must not come into contact with eyes or skin. If it does, wash the affected area with plenty of cold water. If necessary, consult a doctor. Depending on the vehicle, a system continuously checks the battery charge status. When the ignition is off, some consumers may also be switched off (dipped beam headlights, radio, ventilation, etc.).
Tyre pressure when cold Tyre dimensions A A B C D E The tyre pressure is indicated on label A affixed to the edge of the driver’s door. Open the door to read it. Zone D: tyre pressures for the front wheels (motorway) or when driving with a significant load. Zone B: front tyre pressure when driving (non-motorway), or if less than 4 people occupy the vehicle. Zone E: tyre pressures for the rear wheels (motorway) or when driving with a significant load.
Bodywork maintenance (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly.
Bodywork maintenance (2/2) You should – Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. – Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. – Remember to visit the body shop periodically if your vehicle has an anti-corrosion warranty. Refer to the Maintenance Service Booklet. – Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway).
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
4.
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit. . . . . . . . . . . . . . . . . . .
Puncture/emergency spare wheel In the event of a puncture, there is either an emergency spare wheel or tyre inflation kit available, depending on the vehicle (refer to the information in the following pages). To access the emergency spare wheel – Open the tailgate. 1 – Undo the nut with the wheelbrace 1. – Detach the cage using handle 3. – Release the emergency spare wheel. 2 4 3 Emergency spare wheel 2 This is stored in cage 4 under the floor at the rear of the vehicle.
TYRE PRESSURE KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE PRESSURE KIT (2/3) 1 2 Engine running, parking brake applied, 3 4 C 5 6 D 8 Depending on the vehicle, in the event of a puncture use the kit located in the glove box, front upper cab storage compartment C or the luggage compartment, in rear wheel arch D. Open the kit, remove caps 1 and 3 (it is essential not to remove the cap from the bottle) then screw bottle 2 to its base 3.
TYRE PRESSURE KIT (3/3) 10 8 Once the tyre is inflated correctly: – stop using the kit; – close the integrated cap on the bottle again; – disconnect adapter 8; Nothing should be placed around the driver’s feet as such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use.
tool kit Hubcap tool 9 To remove the wheel trims. Jack 7 Refer to Section 5 “Changing a wheel”. 5 1 6 2 3 4 9 8 7 To remove the tool kit 1 from the luggage compartment Depending on the vehicle, it may be stored behind a flap. Open it. Undo wheel 2 and pull the tool kit towards you. The tools included in the tool kit depend on the vehicle. To reposition the tool kit position tool kit pin 4 into housing 3. Make sure the kit is correctly positioned so as to be able to tighten wheel 2.
Wheels - Trim 2 A C 1 B D 3 Wheel trim 1 Wheel trim 3 Remove it using hubcap tool 2 (located under the tool kit), by pushing the hook into the opening located near the valve (to reach the metal retaining wire located behind the wheel trim). To remove it without removing the wheel, press it at the points indicated by the arrows. (concealed wheel bolts) To refit it, align it with the valve.
Changing a wheel (1/2) Continue tightening to position the baseplate on the ground correctly. Turn handle 3 on the jack to lift the wheel off the ground. 1 2 4 Switch on the hazard warning lights. Keep the vehicle away from traffic and on a level surface where it will not slip (if necessary, place a solid support under the jack base). Apply the parking brake and engage a gear (first or reverse, or P for automatic transmissions). Ask all the passengers to leave the vehicle and keep them away from traffic.
CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. For vehicles fitted with alloy wheels, use the guide bolt located in the tool kit to finish loosening and start tightening the bolts. Fit the emergency spare wheel on the central hub and turn it to align the mounting holes in the wheel and the hub. Tighten the bolts and lower the jack. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel.
Tyres (1/3) Tyre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. 2 You must make sure that your tyres conform to local road traffic regulations. 1 When the tyre tread has been eroded to the level of the warning strips, they become visible 2: it is then necessary to replace your tyres because the tread profile is no more than 1.6 mm deep and this causes poor road holding on wet roads.
Tyres (2/3) Tyre pressures Respect the tyre pressures (including the emergency spare wheel). Check them at least once a month and before a long journey (refer to the label on the edge of the driver’s door). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey. If tyre pressures cannot be checked when the tyres are cold, the normal pressures must be increased by 0.2 to 0.3 bar (or 3 PSI). Never deflate a hot tyre.
Tyres (3/3) Use in winter – Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains must not be fitted to tyres which are larger than those originally fitted to the vehicle. – Snow or winter tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum grip. Note: be aware that these tyres may sometimes have: – a direction of travel ; – a maximum speed index which may be lower than the maximum speed of your vehicle.
lights: changing bulbs (1/2) 1 3 2 Dipped beam/main beam headlights Turn cover 1 a quarter of a turn to unlock it. Disconnect the wiring. Remove rubber protector 2. Unclip spring 3 to remove the bulb. Do not touch the bulb glass. Hold it by its base. To refit it, carry out the above operations in reverse order. Ensure that rubber protector 2 is repositioned correctly so that the three strips can be seen.
lights: changing bulbs (2/2) Cleaning the headlights As the headlights are made of plastic glass, use a soft cloth or cotton wool to clean them. If this does not clean it properly, moisten the cloth with soapy water, then wipe clean with a soft damp cloth or cotton wool. A Finally, carefully dry off with a soft dry cloth. 5 4 Front side light Direction indicator lights Turn bulb holder 4 to unlock it and remove it from its location, without disconnecting the wiring. Replace the bulb.
Fog lights: changing bulbs Additional lights If you wish to fit your car with fog lights or long range headlights, consult an approved Dealer. 2 1 Front fog lights 1 As it is necessary to remove parts or components (front bumper), you are advised to have your bulbs replaced by an approved dealer. Bulb type: H11 The engine may be hot during operations in close proximity. In addition, the engine cooling fan may start at any moment. The bulbs are under pressure and can break when replaced. Risk of injury.
Rear lights: changing bulbs (1/3) 2 4 3 1 5 6 2 Rear lights Depending on the vehicle, open the hinged doors or the tailgate. Undo bolts 1 using a Torx tool. Unclip the lower section, then the upper section of the light by pulling it towards you. Pull tabs 2 to unclip bulb holders 3. Replace the bulb, then proceed in the reverse order to refit the bulb. Bulb type 4 Indicator Pear-shaped, bayonet type bulb P Y21W. 5 Side and brake light Pear-shaped, bayonet type bulb with two filaments P 21/5W.
Rear lights: changing bulbs (2/3) 8 7 High-level brake light – Version with tailgate: it is located above the rear screen, in the centre. – Version with hinged doors: it is located above the rear screen, on the left-hand door. Remove the two plastic blanking covers 7 from the inside. Unclip the light using a screwdriver, by pressing in the metal clip housings. Remove light 8 from the outside. Replace the bulb without disconnecting the wiring.
Rear lights: changing bulbs (3/3) 9 10 Number plate light Release the light to access bulbs 10. Undo two bolts 9 using a Torx tool. Bulb type: W5W. Replace the bulbs, then fit the light in position. 5.
INDICATOR LIGHTS: changing bulbs 1 Unclip indicator light 1 on the door side, using a flat-blade screwdriver type tool. 2 Turn bulb holder 2 a quarter of a turn and take out the bulb. Bulb type: WY5W. Replace the bulb and refit the indicator light. 5.
interior lighting: changing bulbs (1/2) 2 1 3 Passenger compartment lights Pull bulbs 2 and 3 downwards to remove them from their housings. Remove lens 1 using a tool such as a flat-blade screwdriver. Bulb type 2: W6W Bulb type 3: W5W Rear courtesy light bulb type: W6W Replace the bulbs and replace the lens. 5.
interior lighting: changing bulbs (2/2) C B A Light A Light B or C Remove the lens using a tool such as a flat-blade screwdriver. Remove the lens using a tool such as a flat-blade screwdriver. Pull the bulb to remove it from its housing. Pull the bulb to remove it from its housing. Bulb type A: W5W Bulb type B or C : W6W Replace the bulb and refit the lens. Replace the bulb and refit the lens. 5.
Battery: troubleshooting (1/2) To avoid all risk of sparks: – Ensure that any consumers (courtesy lights, etc.) are switched off before disconnecting or reconnecting the battery. – When charging, stop the charger before connecting or disconnecting the battery. – Do not place metal objects on the battery to avoid creating a short circuit between the terminals. – Always wait at least twenty seconds after the engine has been switched off before disconnecting a battery.
Battery: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle 1 4 1 If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition. A B 3 2 Connecting a battery charger The battery charger must be compatible with a battery with nominal voltage of 12 volts.
Fuses (1/2) To identify the fuses, refer to the fuse allocation label (shown on the following page). It is not advisable to use the free fuse locations. 1 A Fuse box Tweezers 1 If any electrical component does not work, check the condition of the fuses. Remove the fuse using tweezers 1, located at the back of cover A. Unclip cover A. To remove the fuse from the tweezers, slide the fuse to the side. Check the fuse in question and replace it, if necessary, with a fuse of the same rating.
Fuses (2/2) Allocation of fuses (the presence of fuses DEPENDS ON THE EQUIPMENT LEVEL OF THE VEHICLE) Allocation Some functions are protected by fuses located in the engine compartment. î Radio, display, heating and air conditioning system, heated seat However, because of their reduced accessibility, you are advised to have these fuses replaced by an approved Dealer.
Windscreen wiper blades (1/2) 1 A Replacing windscreen wiper blades With the ignition off, lift wiper arm A slightly. Pull tab 1 upwards. Move the blade in the direction of the arrow. For refitting, proceed in the reverse order and ensure that the blade is correctly clipped on. Check the condition of the wiper blades.
Windscreen wiper blades (2/2) B 4 5 7 C 8 6 Replacing the rear screen wiper blade Hinged door versions B – With the ignition off, lift the wiper arm 6. – Turn blade 4. – Press tab 5. – Pull the blade to release it (arrow). For refitting, proceed in the reverse order and ensure that the blade is correctly clipped on. Tailgate versions C – With the ignition off, lift wiper arm 7. – Pivot blade 8 until some resistance is met. – Pull the blade to release it (arrow).
TOWING: breakdown (1/2) 2 2 1 3 Insert the key into the ignition switch to unlock the steering wheel and to use the indicator lights (brake lights, indicators, etc.). The towed vehicle’s lights must be switched on at night. Furthermore, it is essential to respect the towing regulations set out in the legislation of the country concerned and, if your vehicle is the towing vehicle, not to exceed the towing weight of your vehicle. Contact an approved Dealer. Access to towing points Remove cover 1 or 3.
TOWING: breakdown (2/2) Towing a vehicle with an automatic gearbox With the engine switched off: the gearbox is no longer lubricated. It is preferable to tow this type of vehicle on a trailer or tow it with the front wheels off the ground. 1 Under exceptional circumstances, you may tow the vehicle with all four wheels on the ground, only going forward, with the gear lever in the Neutral position, and for a distance not exceeding 30 miles (50 km).
Towing: equipment A A = 776.5 mm. Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to Section 6 “Weights”. Refer to the manufacturer’s instructions for information on how to fit and operate the towing equipment. Please keep these instructions with the rest of the vehicle documentation. 5.
Fitting a radio (1/2) 1 3 4 5 2 3 Radio equipment Tweeter speakers 4 Bass speakers 5 Unclip the blanking cover. The connections for the aerial, + and – supply, and speaker wires are found behind the cover. The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle version: 1 offset display (time, exterior temperature, radio and navigation); 2 radio position; 3 radio steering column controls.
Fitting a radio (2/2) 6 Rear speakers 6 – In all cases, it is very important to follow the manufacturer’s instructions carefully. – The specifications of the brackets and wires vary depending on the equipment level of your vehicle and the type of radio. Consult an approved Dealer to find out the correct part number.
ACCESSORIES Before fitting an electrical or electronic device (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle. If you are using an anti-theft device, only attach it to the brake pedal. Contact an approved dealer for this information. Electrical and electronic accessories – Connect accessories with a maximum power of 120 Watts only. Use of transmission/ receiving devices (telephones, CB equipment etc.
RADIO FREQUENCY REMOTE CONTROL: batteries 1 2 Replacing the remote control battery Undo screw 1 to remove the remote control cover. Replace battery 2 according to the direction marked on the cover. Note: It is not advisable to touch the electronic circuit in the key cover when replacing the battery. The batteries are available from approved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect electrical contact. 5.
DIESEL FILTER Repriming the fuel circuit If the vehicle runs out of fuel completely, it is necessary to actuate the manual priming bulb after having refilled. The peripheral components (alternator, starter, engine mountings, etc.) should be protected against splashes of fuel. 1 Vehicles with manual priming pump – If fitted to the vehicle, turn the bleed screw located on the diesel filter. – Actuate the repriming bulb 1 until it hardens and fuel runs in the pipes.
Operating faults (1/4) The following advice will enable you to carry out quick, temporary repairs. For safety reasons, you should always contact an approved Dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO Warning lights dim or fail to come on; the starter does not run. Battery terminals disconnected, oxidised or incorrectly secured. Retighten, reconnect or clean them if they are oxidised. Battery discharged or worn. Connect another battery to the faulty battery.
Operating faults (2/4) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to the correct pressure, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved Dealer. Coolant boiling in the coolant reservoir. Mechanical fault: damaged cylinder head gasket. Stop the engine. Contact an approved Dealer. Smoke under the bonnet. Short circuit or cooling system leak.
Operating faults (3/4) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved Dealer. The engine overheats. The coolant temperature indicator and the STOP warning light come on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved Dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an approved Dealer as soon as possible.
Operating faults (4/4) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved Dealer. The wiper does not stop. Faulty electrical controls. Consult an approved Dealer. Direction indicators flashing more quickly. Blown bulb. Replace the bulb. The direction indicators do not work. Faulty electrical circuit. Consult an approved Dealer.
5.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Weights (in kg). . . . . . . . . . . . . . . . .
Vehicle identification plates A 1 2 3 4 5 A The information shown on the vehicle identification plate should be quoted on all correspondence or orders. B 6.2 6 7 8 9 10 Vehicle identification plate A 1 Vehicle type and chassis number. Depending on the vehicle, this information is also given on marking B. 2 Maximum permissible all-up weight. 3 Total train weight (vehicle fully loaded, with trailer). 4 Front axle Maximum permissible weight. 5 Rear axle Maximum permissible weight.
Engine identification plates C 1 2 C 3 C Quote the details given on engine plate C on all communication or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. C 6.
Engine specifications Versions 1.6 16V 1.6 1.5 dCi Engine type (see engine plate) K4M K7M K9K Cubic capacity (cc) 1 598 1 598 1 461 Type of fuel Octane Rating Spark plugs 6.4 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap. If not available, for a limited time only, use unleaded fuel: – with an octane rating of 91 for a label showing 95 or 98; – with an octane rating of 87 for a label showing 91, 95 or 98.
WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact an approved Dealer.
Dimensions (in metres) (1/2) E A B F C D H G 6.
Dimensions (in metres) (2/2) All terrain 5 seater 2 seater Medium A B Long Short Medium Long 2.3 2.7 3.0 3.8 4.2 4.6 0.8 2.7 C D 2 seater 3,1 0.7 4.2 4,6 E 2.1 F 1.5 G 1.5 H (unladen) 1.8 Turning circles between kerbs 10.7 11,9 9.6 10.7 11.9 Turning circles between walls 11.2 12,4 10.1 11.2 12.4 Important: if the vehicle is fitted with roof bars, the height must be increased by 0.070 m (the bars cannot be moved). 6.
Replacement parts and repairs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
service sheets (1/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (2/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (3/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (4/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (5/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (6/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
Anticorrosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Alphabetical index (1/5) A ABS...............................................................1.51, 2.12 → 2.14 accessories........................................................................ 5.33 accessories socket............................................................. 3.22 additional methods of restraint........................................... 1.31 air bag...........................................................1.27 → 1.31, 1.50 activating the front passenger air bags.............1.42 → 1.
Alphabetical index (2/5) emergency brake assist.........................................2.12 → 2.14 emergency braking.................................................2.12 → 2.14 emergency spare wheel....................................................... 5.2 engine technical specifications................................................... 6.4 engine coolant...................................................................... 4.8 engine oil...........................................................1.52, 4.
Alphabetical index (3/5) J jack................................................................................ 5.6, 5.8 L levels..........................................................................4.7 → 4.9 levels: brake fluid....................................................................... 4.7 coolant................................................................... 1.55, 4.8 fuel................................................................................ 1.55 windscreen washer reservoir..
Alphabetical index (4/5) rear screen demisting................................................................. 3.2, 3.4 rear seats functions............................................................ 3.28 – 3.29 rear view mirrors................................................................. 1.67 remote control door locking batteries........................................................................ 5.34 remote control electric door locking............................... 1.2, 1.
Alphabetical index (5/5) W warning lights................................... 1.50 → 1.53, 1.57 → 1.65 washing................................................................... 4.12 – 4.13 weights................................................................................. 6.5 wheelbrace........................................................................... 5.6 wheels (safety)................................................................... 5.10 windscreen washer...................................
( www.e-guide.renault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
