Cyan Magenta Jaune Noir Noir texte SCENIC GRAND SCENIC DRIVER’S HANDBOOK NU840-2 | ENG | Dos = 9 mm | 242 pages | C0 M100 J50 N40 | 1 de Couv
Cyan Magenta Jaune Noir Noir texte recommends ELF ELF is developing a complete range of lubricants for RENAULT: engine oils, manual and automatic transmission oils. Important: to optimize engine operation the use of a lubricant may be restricted to certain vehicles. Please refer to the maintenance documentation. These are very high-technology lubricants stimulated by applied research in Formula One.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections ............................... 1 ................................................................... 2 Your comfort . ........................................................ 3 Maintenance 4 Getting to know your vehicle Driving .......................................................... Practical advice ..................................................... . ..................................... 6 ................................................
0.
Section 1: Getting to know your vehicle RENAULT cards: general information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RAID (Anti-Intruder Device). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seat belts. . . . . . . . . . . . . . . . . . . . . . . . .
RENAULT cards: general information (1/2) The RENAULT card is used for: 1 1 2 3 4 5 2 3 4 5 Unlocking the doors and tailgate. Locking all doors and tailgate. Switching on the lighting remotely. Unlocking/locking the tailgate Integrated key. Special note The RENAULT “SERVICE” card, on equipped vehicles, can be identified by the word “SERVICE” engraved on the card. Refer to the information on the RENAULT “SERVICE” card in section 1.
RENAULT cards: general information (2/2) Access to key 5 Press button 6 and pull on key 5 then release the button. 5 6 Using the key Refer to the information on “Locking/ unlocking the doors”. Once you have accessed the vehicle using the integrated key, replace it in its housing in the RENAULT card, then insert the RENAULT card into the card reader to start the vehicle.
Remote control RENAULT card: use 2 3 1 4 Unlocking the doors and tailgate Press button 1. The hazard warning lights flash once to indicate that the doors have been unlocked. When unlocking is only active for the driver’s door, (refer to the information on the “vehicle settings customisation menu” in Section 1): – pressing button 1 unlocks only the driver’s door and the fuel filler flap; – pressing button 1 twice unlocks all the doors and the tailgate.
RENAULT “hands-free” card: use (1/3) 2 3 1 Use On equipped vehicles, in addition to the functions of the remote control RENAULT card, it can be used to lock/ unlock without using the RENAULT card, when it is in access zone 1. Unlocking the vehicle With the RENAULT card in zone 1, place your hand on a door handle 2: the vehicle will unlock (in some cases, you may need to pull door handle 2 twice to unlock the vehicle and open the door).
RENAULT “hands-free” card: use (2/3) Locking using button 4 If you want to lock your vehicle, the card must be nearby (garage adjacent etc.), with the door and tailgate closed, press button 4 on the handle of the driver’s door. The vehicle will lock. If a door or the tailgate is open or not properly closed, the vehicle will quickly lock/ unlock. 4 1 Note: a RENAULT card must be within the vehicle's access zone (zone 1) to be able to lock the vehicle using the button.
RENAULT “hands-free” card: use (3/3) 5 6 With the engine running, if after having opened and closed a door the card is no longer in the passenger compartment, the message Keycard not detected (accompanied by a beep when the speed exceeds a certain level) warns you that the card is no longer in the vehicle. This prevents you driving away after having dropped off a passenger who has the card, for example. The warning disappears when the card is detected again.
RENAULT CARD: deadlocking To deactivate deadlocking 1 2 If the vehicle is equipped with a deadlocking function, this allows you to lock the opening elements and to prevent the doors from being unlocked using the interior handles (for example, by breaking the window and then trying to open the door from the inside). Unlock the vehicle using button 1 on the RENAULT card. 3 The hazard warning lights flash once to indicate that the doors have been unlocked.
RENAULT “service” card Deactivation of the “SERVICE” mode 2 1 There are two possibilities: – press a button on the RENAULT card (not the RENAULT “SERVICE” card); 3 If the vehicle is equipped with this card, it can be identified by the word “SERVICE” printed on the card. In certain situations, you may wish to entrust your vehicle to a third party (parking valet, mechanic, etc.) whilst restricting its operation. – start the engine with a RENAULT card (not the RENAULT “SERVICE” card).
Opening and closing the doors (1/2) Card reminder buzzer 1 When the driver’s door is opened and the card is still in the reader, the message “Please remove keycard” appears on the instrument panel, accompanied by a beep. 2 Door/tailgate open buzzer Opening the doors from the outside With the doors unlocked or the RENAULT “hands-free” card in your possession, hold handle 1 and pull it towards you. In some cases, it may be necessary to pull the handle twice to open the door.
Opening and closing the doors (2/2) Safety of rear occupants The driver can authorise operation of the rear doors and, depending on the vehicle, the electric windows by pressing switch 3 on the side with the illustration. 3 Child safety Ç Vehicle with switch 3 Press switch 3 to authorise opening of the rear doors. If the vehicle is equipped with electric rear windows, this action will also authorise their use. The indicator light in the switch lights up to confirm that the locks have been activated.
locking/unlocking the doors (1/2) Locking/Unlocking the doors from the outside This is done using the RENAULT Card; see the “RENAULT Card” information in Section 1. 2 In certain cases, the RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc. – use of appliances operating on the same frequency as the card (mobile phone, etc.); – vehicle located in a high electromagnetic radiation zone.
locking/unlocking the doors (2/2) 3 Interior locking/unlocking door control Locking the doors without the RENAULT card Door and tailgate status indicator For example, in the event of a discharged battery or the RENAULT card temporarily not working, etc. When the ignition is on, the indicator light integrated in switch 3 informs you of the status of the doors and tailgate: With the engine switched off and a door or the tailgate open, press and hold switch 3 for more than five seconds.
Automatic locking when driving Activating/deactivating the function To activate: with the vehicle stopped and the ignition on, press switch 1 until a beep sounds. 1 To deactivate: with the vehicle stopped and the ignition on, press switch 1 until two beeps sound. For vehicles equipped with a “TFT Display” instrument panel, you can also deactivate/activate this function.
Front headrests To remove the headrest 2 A B B 1 3 To raise the headrest Pull the headrest upwards to the desired height. To lower the headrest Press button 2 and guide the headrest down to the desired height. To adjust the angle of the headrest Depending on the vehicle, move section A towards or away from you to the required position. Fit it in its highest position, press button 1 on each rod 3 and lift to release.
Front seats with manual control (1/2) 4 2 1 3 To move the seat forwards or back Lift handle 1 to release. Release the handle at the desired position and make sure that it is locked. To raise or lower the seat base To tilt the seatback Turn control knob 3 to the required position. To adjust the lumbar support on the driver’s seat Lower handle 4 to increase the support and lift it to decrease it. Move lever 2 as many times as necessary upwards or downwards.
Front seats with manual control (2/2) 5 6 Table function Depending on the vehicle, the passenger seatback may be folded down onto the seat base to create a table. Lower the headrest if necessary, tilt handle 5 and completely lower the seatback. Heated seats (depending on vehicle) With the engine running, turn control 6 to either position 1, 2 or 3 (depending on the temperature required). An indicator light on the instrument panel lights up once the front seat heating system is operating.
DRIVER’S SEAT WITH ELECTRIC CONTROLS Switch 4 is used for adjusting the seat base and switch 3 is used for adjusting the seatback. On equipped vehicles, buttons 2 store the chosen driving position (refer to the following page). 5 2 Adjusting the seat position To move the seat forwards or back Move switch 4 forwards or backwards. To raise or lower the seat base Move switch 4 upwards or downwards.
Driver’s seat with position memory Recalling a stored driving position It is possible to store three driving positions. A driving position includes the settings for the seat base and seatback of the driver’s seat. With the vehicle stationary, briefly press button 1, 2 or 3 depending on the required stored driving position.
Seat belts (1/3) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belt to ensure optimum protection. Adjusting your driving position Make sure that the rear seats are locked in position properly so that the rear seat belts will operate efficiently.
Seat belts (2/3) ç 3 1 4 6 Adjusting the height of the front seat belts Press button 3 to adjust the seat belt height so that shoulder strap 1 is worn as shown previously. Press button 3 and raise or lower the seat belt. Make sure that the seat belt is locked in position correctly after you have adjusted it. Unfastening Press button 5 and the seat belt will be rewound by the inertia reel. Guide the belt.
Seat belts (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. – For special operations (e.g.: fitting child seats) contact an approved Dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
REAR SEAT BELTS Second row centre rear seat 2 Unwind belt 2 slowly from its housing. 1 3 9 8 6 10 Click buckle 4 into black catch 5. Snap last sliding buckle 6 into the red catch 7. 4 7 On equipped vehicles, for your comfort, you can pass the belt through belt guide 3. 11 12 5 Second row rear side seats Third row rear seats (7-seater versions) Slowly unwind belt 1. Slowly unwind the belt 10. Fasten sliding buckle 9 into corresponding red catch 8.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are composed of: – seat belt inertia reel pretensioners; – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. – lap belt pretensioners; – chest-level load limiter; – air bags for driver and front passenger.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Air bags for driver and front passenger A Fitted to the driver and passenger side. The presence of this equipment is indicated by the word “air bag” on the steering wheel and the dashboard (air bag zone A) and a label on the lower part of the windscreen or on the sun visor.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation This system is only operational when the ignition is switched on. In a severe frontal impact, the air bags inflate rapidly, cushioning the impact of the driver’s head and chest against the steering wheel and of the front passenger against the dashboard. The air bags then deflate immediately so that the passengers are not in any way hindered from leaving the vehicle.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
Methods of restraint in addition to the rear seat belts Depending on the vehicle and the position of the seats, these may comprise: – seat belt pretensioners built into the inertia reels; – force limiter. These systems are designed to act independently or together when the vehicle is subjected to a frontal impact. There are two possibilities, depending on the force of the impact: – protection is provided by the seat belt only; – the pretensioner is triggered to rectify seat belt slack.
Side protection devices Side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Curtain air bags These are air bags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear side windows to protect the passengers in case of a severe side impact.
Additional methods of restraint All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
Child safety: general information Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: Choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. Forward-facing child seats The child’s head and abdomen need to be protected as a priority.
child safety: choosing a child seat mounting (1/2) There are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Before using an ISOFIX child seat that you purchased for another vehicle, check that its installation is authorised.
child safety: choosing a child seat mounting (2/2) 1 4 3 6 5 2 Attachment using the ISOFIX system (continued) The two rings 1 are located between the seatback and the seat base of the seat and are identified by a marking. To ensure your child seat can be easily fitted and locked on the rings 1, use access guides 2 on the child seat. The third ring 3, 4 and 5 (for long chassis versions) or 6 (for short chassis versions) is used to attach the upper strap on some ISOFIX seats.
child safety: fitting a child seat (1/9) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
child safety: fitting a child seat (2/9) In the rear seat In the rear centre seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest the door. Some child seats are too wide to allow access to the seat belt buckles. Check that your child seat can be fitted in this seat.
child safety: child seat installation diagram (3/9) Child seat attached using the ISOFIX mounting 5-seater normal chassis version ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchoring points are visible on the floor behind the seat concerned or under the carpet, and indicated by a marking.
child safety: fitting a child seat (4/9) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: child seat installation diagram (5/9) 5-seater long chassis version Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchoring points are visible on the floor behind the seat concerned or under the carpet, and indicated by a marking.
child safety: fitting a child seat (6/9) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: child seat installation diagram (7/9) 7-seater version Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchoring points are located on the floor behind the seat concerned and indicated by a marking.
child safety: fitting a child seat (8/9) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: fitting a child seat (9/9) X =S eat not suitable for fitting child seats. U = Seat allowing a child seat with “Universal” approval to be attached by seat belt; check that it can be fitted correctly. equipped vehicles, seat which allows a child seat with “Universal/Semi-universal or vehicle specific” approval to be IUF/IL = On fitted using the ISOFIX system; check that it can be fitted correctly.
child safety: deactivating/activating the front passenger air bag (1/2) A 1 The front passenger air bag must only be deactivated or activated when the vehicle is stationary. If it is interfered with when the vehicle is being driven, indicator lights on. å and © will come Switch the ignition off then on again to reset the air bag in accordance with the lock position.
child safety: deactivating/activating the front passenger air bag (2/2) Operating faults A 1 It is not permitted to fit a rear-facing child seat to the front passenger seat if the air bag activation/deactivation system is faulty. It is not recommended to allow any other passenger to sit in that seat if the › ¹ two warning lights are lit at the same time. and Contact your approved dealer as soon as possible.
Driving position: left-hand drive (1/2) 1 2 3 27 4 25 24 26 5 6 7 8 9 10 11 12 23 22 18 17 21 13 14 15 16 19 20 1.46 ENG_NU_840-2_JR95_Renault_1 ENG_UD7430_1 Poste de conduite direction à gauche (X95 - J95 - R95 - Renault) Driving position driver’s position..................................... (up to the end of the DU) controls..................................................
Driving position: left-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 2 Side window demister outlet. 3 Stalk for: – direction indicator lights; – exterior lights; – front fog lights; – rear fog light. 4 Location for driver’s air bag and horn. 5 – Steering column stalk for windscreen and rear screen wash/ wipe. – Trip computer information readout control and vehicle settings personalisation menu. 6 Instrument panel. 7 Centre air vents.
Driving position: right-hand drive (1/2) 1 2 3 27 26 4 5 6 7 8 9 25 24 23 10 11 20 19 18 21 22 12 17 1.48 ENG_NU_840-2_JR95_Renault_1 ENG_UD12951_2 Poste de conduite direction à droite (X95 - J95 - R95 - Renault) driver’s position..................................... (up to the end of the DU) controls..................................................
Driving position: right-hand drive (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 11 Stalk for: 2 Side window demister outlet. – direction indicator lights; 3 Location for passenger air bag. – exterior lights; 4 Centre air vents. – front fog lights; 5 – Display (depending on the vehicle) for time, temperature, radio information, navigation system information, etc. – rear fog light.
Steering wheel/power-assisted steering Power-assisted steering Variable power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. 1 Operating faults The steering may become stiff when driving or when the steering wheel is turned repeatedly. This is due to the power assistance overheating. In this case, it must be allowed to cool down.
Instrument panel: warning lights (1/5) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Φ A B Speed limiter and cruise control indicator lights See the information on the “Speed limiter” and “Cruise control” in Section 2. 1 Depending on the vehicle, the instrument panel features a customisable display (A) or a non-customisable display (B).
Instrument panel: warning lights (2/5) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY.
Instrument panel: warning lights (3/5) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ç Driver’s seat belt reminder and, depending on the vehicle, front passenger seat belt reminder This lights up on the instrument panel when the ignition is started, then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approximately 12 mph (20 km/h), it flashes and a bleep sounds for around 120 seconds.
Instrument panel: warning lights (4/5) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. B A © Warning light This lights up when the ignition is switched on and goes out after approximately three seconds. It can light up in conjunction with other indicator lights and/or messages on the instrument panel. It means you should drive very carefully to an approved Dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
Instrument panel: warning lights (5/5) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. The following warning lights come on accompanied by the ® warning light. D Brake circuit fault warning light If it comes on during braking and is accompanied by the ® warning light and a beep, it indicates that the fluid level in the circuit is low or that there is a braking system fault. Stop as soon as traffic conditions allow and contact an approved Dealer.
Instrument panel: display and indicators (1/4) Rev counter (rpm × 1,000) This is displayed according to how the instrument panel is customised. 2 3 Speedometer (km/h or mph) A Fuel gauge The remaining fuel level is shown in yellow. 1 M 2 If the level is at the minimum, the warning light integrated in the indicator comes on, accompanied by a beep. Fill up as soon as possible.
Instrument panel: display and indicators (2/4) 3 5 4 Instrument panel in miles (option to switch to km/h) – With the ignition off, press button 3 or 4 and start button 5; – the speedometer unit indicator flashes for approximately ten seconds, then the new unit is displayed: release button 3 or 4 when the unit stops flashing. To return to the previous mode, repeat the same operation.
Instrument panel: display and indicators (3/4) 6 7 8 B Vehicle without “TFT Display” instrument panel Instrument panel B Fuel level gauge 6 M If the level is at the minimum, the warning light integrated in the indicator comes on, accompanied by a beep. Fill up as soon as possible.
Instrument panel: display and indicators (4/4) 2 3 2 4 Instrument panel in miles (option to switch to km/h) – With the ignition off, press button 3 or 4 and start button 5. – The speedometer unit flashes for approximately ten seconds, then the new unit is displayed: release button 3 or 4 when the unit stops flashing. To return to the previous mode, repeat the operation.
Trip computer and warning system (1/9) c) mileage before service; d) tyre pressure monitor; 1 2 e) cruise control/speed limiter programmed speed (only for vehicles which are not equipped with a “TFT Display” instrument panel); f) on-board log, operating fault and information message readout.
Trip computer and warning system (2/9) 2 3 Trip mileage resetting With “trip mileage recorder” selected on the display, press button 2 or 3 until the mileage recorder resets to zero. Interpreting some of the values displayed after resetting The values showing average fuel consumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed.
Trip computer and warning system (3/9) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected a) Total mileage and trip mileage recorder. b) Journey parameters. Fuel used. Fuel consumed since the last reset. Average fuel consumption since the last reset. The value is displayed after having travelled at least 400 metres since the last reset. 1.62 ENG_NU_840-2_JR95_Renault_1 instrument panel messages................
Trip computer and warning system (4/9) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Current fuel consumption. This value is displayed above a speed of approximately 18 mph (30 km/h). Estimated range with remaining fuel. The value is displayed after driving 400 metres. Distance travelled since the last reset. Average speed since the last reset. The value is displayed after driving 400 metres. 1.
Trip computer and warning system (5/9) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected c) Mileage before service.
Trip computer and warning system (6/9) Journey parameters The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected d) Tyre pressure monitor. Refer to the information on the “Tyre pressure monitor” in Section 2. e) Cruise control/speed limiter programmed speed (only for vehicles which are not equipped with a “TFT Display” instrument panel).
Trip computer and warning system (7/9) Information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages “Parking brake on” Interpreting the display selected Indicates that the parking brake has been applied. “Please remove keycard” Request to remove the RENAULT card from the reader when you leave the vehicle.
Trip computer and warning system (8/9) Operating fault messages These appear with the © warning light and mean that you should drive very carefully to an approved Dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given in the following pages.
Trip computer and warning system (9/9) Warning messages These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Vehicle settings customisation menu Adjusting the settings 1 4 2 3 Depending on the vehicle equipment, press button 3 or 4 to select the function to be modified: a) Auto door locking while driving; b) Unlock driver’s door only; c) Auto rear wipe with reverse gear; d) Auto dipped-beam headlights; e) Front parking sensor; f) Rear parking sensor; g) Parking sensor volume; h) Time; i) LANGUAGE.
Clock and exterior temperature 1 External temperature indicator 2 Special note: When the outside temperature is –3°C to +3°C, the °C characters flash (signalling a risk of black ice on the road). 3 4 5 Resetting the clock 1 Vehicles fitted with control 3 – Press and hold button 2 for approximately three seconds; Select “clock” from the vehicle settings customisation menu (see previous page). Press button 4 to scroll through the hours and button 5 to confirm.
Rear view mirrors Folding door mirrors A B 1 3 C D E 2 The door mirrors automatically fold in when the vehicle is locked (switch 2 in position D). In this case, they will fold out when the ignition is next switched on. In any case, you can make the door mirrors fold in (switch 2 in position E) or out (switch 2 in position C). Automatic mode is then deactivated. To reactivate it, set switch 2 to D. 4 Door mirrors Interior rear view mirror Adjustment Its position can be adjusted.
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. 1 A 2 When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0. There is an intermediate position in which the stalk may be held when changing lanes. When the stalk is released, it automatically returns to 0. Horn Press on the sides of the steering wheel boss A.
Exterior lighting and signals (1/3) á 1 Main beam headlights With the dipped beam headlights lit, pull stalk 1 towards you. This indicator light on the instrument panel comes on. 2 1 To return to the dipped headlight position, pull stalk 1 towards you again. Daytime running lights function 3 u Side lights Turn ring 3 until the symbol is opposite mark 2. This indicator light on the instrument panel comes on.
Exterior lighting and signals (2/3) Special features 1 2 3 Directional headlights Depending on the vehicle, with the dipped beam headlights on and under certain conditions (speed, steering wheel angle, forwards gear selected, etc.) when cornering, the dipped beam headlights move to light the inside of the bend. Operating faults When the message “Check lighting”, accompanied by the © warning light is displayed on the instrument panel, there is a lighting fault. Consult an approved dealer.
Exterior lighting and signals (3/3) g 1 4 Front fog lights Turn centre ring 5 on stalk 1 until the symbol faces mark 4, then release it. Operation of the fog lights depends on the exterior lighting position selected, and an indicator light will light up on the instrument panel. 5 Lights-on reminder buzzer If the lights are on after the engine is switched off, a warning beep sounds when the driver’s door is opened to warn you that the lights are still on.
Electrical adjustment of the dipped beam headlights For manual settings Examples of positions for adjusting control A according to the load Driver alone or with front passenger 0 Driver with one front passenger and one rear passenger 0 Driver with one front passenger and two or three rear passengers 1 Driver with one front passenger, three rear passengers and luggage 3 Driver with luggage or (load) reaching the maximum permissible allup weight 3 A On vehicles fitted with this function, control A
Windscreen wiper, washer (1/2) Vehicle fitted with front windscreen wiper rain sensor 1 E 1 2 A D B C F A park B automatic wiper function When this position is selected, the system detects water on the windscreen and triggers the wipers at a suitable wiping speed.
Windscreen wiper, washer (2/2) Headlight washers 1 A D B C Windscreen washer Headlights on On equipped vehicles, hold stalk 1 pulled towards you for about 1 second, and the headlight washers and windscreen washers will be activated at the same time. Note: when the minimum windscreen washer fluid level is reached, the headlight washer system may be deprimed. Fill the windscreen washer fluid and then activate the windscreen washer, with the engine running, to reprime the system.
Rear screen wash/WIPE 1 Activating/deactivating the rear screen wiper (depending on the vehicle) A 2 Y Rear screen wiper With the ignition on, turn ring A on stalk 1 to align the symbol with mark 2 then release it. To stop the operation, pivot ring A again. Wiping frequency varies with vehicle speed. If your vehicle is fitted with a vehicle settings customisation menu, it is programmed to activate the rear wipers when reverse gear is selected (if the windscreen wipers are on).
FUEL TANK (1/2) Fuel grade Use a high-grade fuel that complies with the legislation in force in each country and which must conform to the specifications given on the label on the cover B. Refer to the information on “Engine specifications” in Section 6. B A C Useable fuel tank capacity: 60 litres approximately. With the vehicle unlocked, to open the compartment B, place your finger into the recess C.
FUEL TANK (2/2) Filling with fuel Insert the nozzle to open valve A and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position throughout the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts may be made, as there must be sufficient space in the fuel tank to allow for expansion. Make sure that no water enters the fuel tank during filling.
1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting - stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special features of petrol versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN Petrol version Diesel version Up to 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in top gear or 3,000 to 3,500 rpm. For the first 900 miles (1,500 km), do not exceed 2,500 rpm. After completing this mileage you may drive faster, however, it is only after approximately 3600 miles (6,000 km) that you may reasonably expect full performance. You may only expect top performance from your vehicle after approximately 1,800 miles (3 000 km).
STARTING THE ENGINE (1/2) Starting the vehicle – For vehicles with automatic gearboxes, set the lever to the P position. 1 2 Remote control RENAULT card When you get into the vehicle, insert the RENAULT card fully into card reader 2. To start, press button 1. If a gear is engaged, depress the clutch pedal to start the vehicle. 3 RENAULT “hands-free” card The RENAULT card must be inserted in card reader 2 or in detection zone 3. To start, depress the brake or clutch pedal and press button 1.
STARTING THE ENGINE (2/2) For other functions: – vehicles with remote control RENAULT card, insert the card into reader 2; 1 – vehicles with a RENAULT “handsfree” card, with the card in the passenger compartment or inserted in the card reader 2, press button 1 without depressing the pedals. 2 Note: if there is a card in the reader, pressing button 1 starts the engine.
Stopping the engine Special note If the card is no longer in the reader when you try to switch the engine off, the message “No keycard Press and hold” appears on the instrument panel: press button 1 for longer than two seconds. 1 When you leave your vehicle, especially if you have your RENAULT card with you, check that the engine is completely switched off.
Special features of petrol versions The following operating conditions should be avoided: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
Special features of diesel versions Diesel engine speed Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected. If the message “Check antipollution system” is displayed on the instrument Ä and panel accompanied by the © warning light; consult an approved dealer straight away.
Gear lever/Handbrake Handbrake 1 To release: Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. To apply: 3 Pull the lever 2 upwards and make sure the vehicle is immobilised. 2 Make sure that the handbrake is properly released when driving (red indicator light off), otherwise overheating may occur. Selecting reverse gear Vehicles with manual gearbox: follow the grid drawn on knob 1, and depending on the vehicle, lift ring against the gear lever knob to select reverse.
ELECTRONIC PARKING BRAKE (1/3) Note: 1 2 3 To indicate that the electronic parking brake is applied or released, a beep sounds and the message “Apply parking brake” appears on the instrument panel: – with the engine running: when the driver’s door is opened; – with the engine switched off (eg. when the engine stalls): when a front door is opened. In this case, pull and release switch 3 to apply the electronic parking brake.
ELECTRONIC PARKING BRAKE (2/3) Special cases When parking on a slope or towing a trailer, pull switch 3 for a few seconds to obtain the maximum braking effect.
ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic gearbox For safety reasons, automatic release is deactivated when the driver’s door is open or not properly closed and the engine is running (in order to prevent the vehicle from moving without the driver). The message “Release parking brake manually” appears on the instrument panel when the driver depresses the accelerator. Never leave your vehicle without moving the selector lever to position P or N.
Advice: antipollution, fuel economy and driving (1/3) By virtue of its design, moderate fuel consumption and initial settings, your vehicle conforms to current antipollution regulations. The manufacturer is actively striving to reduce pollutant exhaust gas emissions and to save energy. But the fuel consumption of your vehicle and the level of pollutant exhaust gas emissions are also your responsibility. Ensure that it is maintained and used correctly.
Advice: antipollution, fuel economy and driving (2/3) Ä This warning light on the instrument panel will indicate if there are any faults in the system: This lights up when the ignition is switched on and goes out when the engine is started. – If it lights up continuously, consult an approved Dealer as soon as possible; – if it flashes, reduce the engine speed until the light stops flashing. Contact your approved dealer as soon as possible.
Advice: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. Manufacture Your vehicle has been manufactured in a factory which complies with the strictest environmental standards. Furthermore, a system has been implemented for checking all of the vehicle components.
Tyre pressure monitor (1/4) If the vehicle is equipped with the function, this system monitors the tyre pressure. 1 Operating principle Each wheel (except for the emergency spare wheel) has a sensor in the inflation valve which periodically measures the tyre pressure. The system informs the driver via the trip computer and warning system 1 that the tyres are sufficiently inflated and warns if they are underinflated or leaking. Never deflate a hot tyre.
Tyre pressure monitor (2/4) “Tyre pressure sensors absent” or “Check tyre pressure sensors” One wheel B disappears, indicating that the sensor on this wheel is missing or faulty (e.g. if the emergency spare wheel is fitted). B A C vehicles without “TFT display” instrument panels A “Inflate tyres for motorway” The tyre pressure is not suitable for the speed of travel. Slow down or inflate all four tyres to motorway pressure (refer to the information on “Tyre pressures”).
Tyre pressure monitor (3/4) 3 4 3 D E “Inflate tyres for motorway” The wheel concerned E is shown in orange on display 4. The tyre pressure is not suitable for the speed of travel. Slow down or inflate all four tyres to motorway pressure (refer to the information on “Tyre pressures” in Section 4). “Adjust tyre pressure” The wheel concerned E is shown in orange on display 4 and indicates a flat tyre. Display 3 reminds you of this information.
Tyre pressure monitor (4/4) Replacing wheels/tyres This system requires specific equipment (wheels, tyres, hubcaps, etc.). Contact an approved Dealer to fit new tyres and to find out about available accessories compatible with the system and available from your dealer network: the use of any other accessory could affect the correct operation of the system or damage a sensor.
Driver correction devices and aids (1/3) Depending on the vehicle, this is composed of: – the ABS (anti-lock braking system); – the electronic stability program ESP with understeer control and traction control ASR; – emergency brake assist with, depending on the vehicle, braking anticipation. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions.
Driver correction devices and aids (2/3) Electronic stability program ESP with understeer control and traction control ASR Electronic stability program ESP This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
Driver correction devices and aids (3/3) 1 The traction control ASR offers additional safety, it is recommended that you do not drive with the function disabled. Correct this as soon as possible by pressing switch 1 again. Note: the function is reactivated automatically when the ignition is switched on or when a speed of approximately 24 mph (40 km/h) is exceeded. Emergency brake assist This system supplements the ABS and helps reduce vehicle stopping distances.
Cruise control/speed limiter: speed limiter function (1/3) The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. 1 2 A 4 3 5 Controls Switching on 1 Limit speed activation, storage and increase switch (+). 2 Limit speed storage and decrease switch (-). 3 Switching the function off (with limit speed storage) (O). 4 Limit speed activation, storage and recall (R). 5 Main “On/Off” switch. Press switch 5 on the side showing .
Cruise control/speed limiter: speed limiter function (2/3) Driving Exceeding the limit speed When a limited speed has been stored and this speed is not reached, driving is similar to driving a vehicle without the speed limiter function. It is possible to exceed the limit speed at any moment. To do this: press the accelerator pedal firmly and fully (beyond the kickdown point).
Cruise control/speed limiter: speed limiter function (3/3) Switching off the function 1 2 4 3 A The speed limiter function is deactivated if you press switch 5: in this case a speed is no longer stored. The orange indicator light on instrument panel A goes out to confirm that the function is deactivated. 5 Putting the function on standby The speed limiter function is suspended when you press switch 3 (O).
Cruise control/speed limiter: cruise control function (1/4) The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). 1 2 4 3 5 Controls 1 Limit speed activation, storage and increase switch (+). 2 Decrease cruising speed (-). 3 Switching the function off (with stored cruising speed) (O). 4 Activation with recall of stored governed cruising speed (R).
Cruise control/speed limiter: cruise control function (2/4) Driving 1 2 4 3 A Once a cruising speed is stored and the cruise control function is active, you may lift your foot off the accelerator pedal. 5 Switching on Activating cruise control Press switch 5 on the side showing . At a steady speed (above 20 mph (30 km/h) approximately) press switch 1 (+): the current speed is stored.
Cruise control/speed limiter: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelerator pedal. 1 2 4 3 5 Adjusting the cruising speed The cruising speed may be changed by pressing the following repeatedly: – switch 1 (+) to increase the speed, – switch 2 (-) to decrease the speed.
Cruise control/speed limiter: cruise control function (4/4) Switching off the function 1 2 4 3 A The cruise control function is deactivated if you press switch 5: in this case a speed is no longer stored. The green indicator light on the instrument panel A goes out to confirm that the function is deactivated. 5 Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.).
PARKING DISTANCE CONTROL (1/3) Operating principle Ultrasonic detectors, installed in the front or rear bumper depending on the vehicle, measure the distance between the vehicle and an obstacle whilst reversing. 1 This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centimetres from the obstacle. Note: display 1 shows the vehicle surroundings using beeps.
PARKING DISTANCE CONTROL (2/3) Front parking distance control (depending on vehicle) 1 Operation The parking distance control system is only activated when the vehicle is driven at a speed below approximately 6 mph (10 km/h). Most objects located less than approximately 60 centimetres away from the front of the vehicle are detected and a beep is emitted. Depending on the vehicle, the red area on display 1 lights up. Note: when manoeuvring, the object detection area switches to approximately one metre.
PARKING DISTANCE CONTROL (3/3) You can also adjust the volume. A From the vehicle settings customisation menu (refer to the information on the “Vehicle settings customisation menu” in Section 1), select the line “Parking sensor volume ” then decrease or increase it: Note: when the volume is set to minimum, guidance is only provided by the visual on the instrument panel.
Reversing camera 1 2 A B C Fixed clearance gauge 2 The fixed clearance gauge comprises coloured markers A, B and C indicating the distance behind the vehicle: – A (red) approximately 50 centimetres from the vehicle; – B (yellow) approximately 1 metre from the vehicle; – C (green) approximately 2 to 3 metres from the vehicle. This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle.
Automatic gearbox (1/3) Operation Driving in automatic mode 1 With the gear lever 1 in position P, switch on the ignition. 2 With the foot on the brake pedal (warning light c on the display goes out), move the lever out of position P. Select position D.
Automatic gearbox (2/3) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, move the lever to the left. Shifting the lever repeatedly allows you to change gears manually: – if the road contours and bends do not allow you to stay in automatic mode (e.g.: in mountains), we recommend that you change to manual mode.
Automatic gearbox (3/3) Operating faults – when driving, if the message “Check auto gearbox” appears on the instrument panel, this indicates there is a fault. Contact your approved Dealer as soon as possible; A 2 3 – when driving, if the message “Auto gearbox overheating” appears on the instrument panel, stop the vehicle to allow the gearbox to cool down.
Section 3: Your comfort Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual air conditioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air conditioning: information and advice on use . . .
AIR VENTS (air outlets) (1/2) 1 2 3 4 5 6 7 7 9 8 8 1 left-hand side air vent 8 2 left-hand side window demister outlet 7 rear air vents 3 windscreen demister outlets 8 passenger footwell heater outlets 4 centre air vents 9 automatic climate control/manual air conditioning control panel. 5 right-hand side window demister outlet 6 right-hand side air vent 3.2 ENG_NU_840-2_JR95_Renault_3 ENG_UD7459_1 Aérateurs (sorties d’air) (X95 - J95 - R95 - Renault) Air vents air vents..............
Air vents (2/2) 1 3 2 4 2 Front seats Air flow Turn control knob 1 (beyond the point of resistance): 1 To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. Rear seats Move tab 3 to the right or left to direct the air flow. Turn control knob 4: – downwards to decrease the air flow and direct it downwards; Up: maximum air flow. Down: closed. – upwards to increase the air flow and direct it upwards.
Manual air conditioning (1/2) 2 1 3 4 Distribution of air in the passenger compartment There are five air distribution options. Turn control 4 to choose the distribution option. W i The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells. The controls 6 1 Adjusting the air temperature.
Manual air conditioning (2/2) 1 2 3 4 Adjusting the ventilation speed Turn control 2 clockwise to increase the air flow in the passenger compartment. Passenger compartment ventilation is referred to as “blown air”. The ventilation fan determines the air flow. However, it is also affected by the vehicle speed. Switching the air recirculation on “OFF" position: The system is deactivated: the ventilation speed is zero (vehicle stationary).
automatic climate control (1/5) 2 3 4 Automatic mode 5 6 13 1 The controls 12 11 10 1 and 6 Air temperature. 2, 3 and 4 Automatic programmes. 5 Distribution of air in the passenger compartment. 7 Off button. 8 Air conditioning. 9 8 The automatic climate control system ensures, in most cases, a comfortable temperature in the passenger compartment, while maintaining good visibility and optimising fuel consumption.
automatic climate control (2/5) Clear View function 3 1 Press button 10: the integrated indicator light comes on. 13 6 This function quickly demists and deices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen deicing functions must be activated. Press button 9 to stop the heated rear screen operating; the integrated indicator goes out.
automatic climate control (3/5) 3 The displayed temperature values show a comfort level. Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions. Press switch 8 to switch off the air conditioning; the integrated indicator comes on and “AC OFF” is shown on display 12. 12 8 When starting the engine, increasing or decreasing the value displayed will not allow the comfort level to be reached any more quickly.
automatic climate control (4/5) W × The air flow is directed to the windscreen and the front side window demisting vents. 5 The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells. 13 Rear screen de-icing/ demisting ¿ ¾ 12 B Press button 9: the integrated indicator light comes on. This function permits rapid demisting/de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles).
automatic climate control (5/5) Recycling 2 This function is controlled automatically, but it can also be activated manually. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle; – air recirculation allows the external atmosphere to be cut off (when driving in polluted areas, etc.); – lowering the passenger compartment temperature as quickly as possible.
Air conditioning: information and advice on use Advice on use In some situations (air conditioning off, air recirculation activated, ventilation speed at zero or low, etc.), you may notice that condensation starts to form on the windows and windscreen. If there is condensation, use the “Clear View” function to remove it, then use the air conditioning in automatic mode to stop it forming again. If the condensation does not clear, use the FAST programme.
Electric windows/Electric sunroof (1/3) These systems operate with the ignition on or off, until one of the front doors is opened (limited to about 3 minutes). Safety of rear occupants Depending on the vehicle, the driver can disable operation of the electric windows and the rear doors by pressing switch 4. The indicator light integrated in the switch lights up to confirm that the locks have been activated.
Electric windows/Electric sunroof (2/3) Remote control window closing (vehicles with 4 one-touch electric windows). 0 When you lock the doors from the outside, press the locking button on the RENAULT card twice in quick succession, or on the driver's door in hands-free mode, and all the windows will close automatically. A B C D 8 9 7 It is recommended that the user only operates the system when the vehicle can be seen clearly and no one is inside.
Electric windows/Electric sunroof (3/3) Operating faults Precautions during use Electric windows In case of a fault when closing a window, the system reverts to normal mode: pull the switch concerned up as often as necessary to fully close the window (the window will close gradually), hold the switch (still on the closure side) for three seconds then lower and raise the window fully to reinitialise the system. If necessary, contact an approved Dealer.
MANUAL WINDOW WINDERS/Interior lighting (1/2) 1 2 3 4 5 Manual window winders Courtesy light Front door lights Turn handle 1. Tilt switch 3 to move it to the position for: On equipped vehicles, light 5 comes on when the door is opened. – permanent lighting; – intermittent lighting, which comes on when a door is opened. This switches off after a time delay, once the doors concerned have been closed correctly; – immediate switching off.
Interior lighting (2/2) 7 6 7 Glove box light 6 Luggage compartment light 7 Light 6 comes on when the cover is opened. Depending on the vehicle, light 7 comes on when the luggage compartment is opened. 3.
SUN BLIND/mirrors 4 2 1 3 Front sun visor Vanity mirror Child minder mirror Lower the sun visor 1 over the windscreen or unclip it and lower it over the side window. Slide cover 3. Pull on recess 4 to open it. Depending on the vehicle, light 2 is automatic. 3.17 ENG_NU_840-2_JR95_Renault_3 Sun blind sun visor................................................ (up to the end of the DU) courtesy mirrors.....................................
SUN VISOR 5 2 1 4 3 6 Lateral sun visor Rear side sun blind Rear sun blind on the tailgate Pull the sun blind upwards using tab 1 until hook 2 engages in its housing (make sure that the hook is correctly clipped in). Pull the sun blind upwards using hook 3 until it engages in housing 4 (make sure that the hook is correctly clipped in). Pull the sun blind upwards using tabs 6 until they engage in hook 5 (make sure they are correctly clipped in). 3.18 ENG_NU_840-2_JR95_Renault_3 sun blinds........
Passenger compartment storage/fittings (1/6) 2 3 1 Door pockets 1 It can hold a 1.5 litre bottle. Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use.
Passenger compartment storage/fittings (2/6) 5 4 6 Sunglasses holder 4 Sun blind storage 5 This can be used for storing motorway tickets, cards, etc. Central storage compartment or control 6 Depending on the vehicle, central control 6 may be replaced by a storage compartment. 3.
Passenger compartment storage/fittings (3/6) 10 8 A 7 C D B 9 Central elbow rest 8 The central elbow rest slides to allow the length to be adjusted. Slide it (movement A). Centre console 9 The centre console slides to allow the length to be adjusted. Lift handle 7 and slide the console (movement B). Central storage compartment C Armrest storage compartment D Raise armrest 8. With the armrest in the retracted position, press button 10 and lift armrest 8. The compartment can hold a 1.
Passenger compartment storage/fittings (4/6) 11 10 Passenger storage compartment 11 Cup holder 11 It can hold a can, a cup or the ashtray. Pull handle 10 to open it. The glove box can hold A4-size documents, a large bottle of water, etc. The storage compartment is ventilated and refrigerated. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of burning if hot liquid escapes. 3.
Passenger compartment storage/fittings (5/6) 13 14 12 15 13 Rear door storage compartment 12 Front seat storage compartments 13 Clothes hooks 14 Grab handle 15 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning or braking. 3.
Passenger compartment storage/fittings (6/6) 16 18 17 Retaining hook 16 This is used to hold bags while the vehicle is moving. Note: do not exceed a load of 9 kg. Storage drawer 17 under front and rear seats Front and rear underfloor storage areas 18 These drawers can hold a road atlas, the vehicle documentation, etc. These compartments can hold road maps, manuals, cloths, etc. Special feature of rear storage areas The storage area covers may be removed: once open, pull up.
Ashtray/cigar lighter/accessories socket 1 3 3 2 Cigar lighter 1 Accessories sockets With the ignition on, push in cigar lighter 1; it will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in. You may use cigar lighter recess 1 or one of the sockets 3 (depending on the vehicle). They are designed for connecting accessories with a maximum power rating of 120 Watts (voltage: 12V) which have been approved by our Technical Department.
Rear headrests A B 1 Position for use To adjust side supports A Lift the headrest to maximum height, then lower it until it locks. Depending on the vehicle, sections A can be adjusted independently to the desired position. To remove the headrest Press the tab(s) 1, then remove the headrest. To refit the headrest Insert the rods into the holes, press tab 1 and lower the headrest. Storage position B Press tab 1 and lower the headrest completely.
Child’s convertible headrest 1 Removing a headrest Press tab 4 and release the headrest. 2 4 3 A Fitting a headrest Insert the headrest rods in the holes. Pull the headrest towards you and slide it to the desired height at the same time. B A 6 5 This headrest, with its booster seat, may only be fitted in the second row rear side seats of your vehicle. For additional information, contact an approved Dealer. The headrest is a safety component.
ADJUSTING THE REAR SEATS 3 1 To fold down a seatback (table position) 3 4 Lower headrest 3. 1 4 Lift handle 4 or, depending on the vehicle, pull tab 1. An occasional table position can be created by folding the seatback all the way down onto the seat cushion. The seats can hold up to 80 kg in this position. 2 The rear seats are separate seats. To tilt the seatback To move the seats forwards or backwards Lift handle 4 or pull strap 1 and tilt the seatback to the desired position.
REAR SEAT FUNCTIONS (1/2) 1 1 5 3 1 2 Folding up a seat Lower the headrest. Seat with control 2 Lift the control 2, the seatback is lowered and lift the seat as far forwards as possible. Seat without control 2 Lift control 1 or pull belt 3 and tilt the seatback into the table position. Then, lift control 4 or pull belt 5 and lift the seat as far forwards as possible.
REAR SEAT FUNCTIONS (2/2) When fitting side seats, make sure that the seat belt buckle is inside the vehicle. B 6 7 8 9 7 To remove a seat With the seat folded down, gently lower it while lifting handle 7. Release the handle and guide the seat to the floor. Remove the seat from the vehicle by lifting it using handle 6. Once the rear seats have been removed, ensure that they are rested on a flat surface so as not to damage the units under the seats (depending on the vehicle).
REAR SEAT OPERATION: 7-seater version (1/2) 1 1 A A A A 2 Third row rear seats Folding up a seat – From the luggage compartment, lower the headrest; – pull strap 2; – push the seatback (areas A) to lock the seat, ensuring that it is correctly locked. Note: the hooks 1 secure the seat belt buckles.
24508 REAR SEAT OPERATION: 7-seater version (2/2) 3 Accessing the third row rear seats – Via the rear doors, push the second row seat forwards; – lower the seat headrest; – lift handle 3; the seatback lowers itself. Fold the seat down; – pull the second row rear seat to put it into the table position; – lift the seatback. Use restriction It is not permitted to drive with a second row rear seatback or seat folded down when there is a passenger occupying a third row rear seat.
Tailgate 2 1 To open Press button 1 and lift the tailgate. To close Lower the tailgate using the handles 2 inside the tailgate to help you. 3 Opening manually from inside the vehicle Special note If it is impossible to unlock the tailgate, it can be done manually from inside: – access the luggage compartment by tilting the rear bench seatback(s), – insert a pencil or similar object in recess 3 and slide the unit as shown in the illustration, – push the tailgate to open it. 3.
REAR PARCEL SHELF: normal chassis versions 1 B A Rear parcel shelf To remove, unhook the two straps 1. Fold section A onto section B, then pull up and towards you. To refit it, proceed in reverse order to removal. Maximum load on the rear parcel shelf: 25 kg evenly distributed. Do not place any objects, especially heavy or hard objects, on the parcel shelf. These may pose a risk to the vehicle occupants if the driver has to brake suddenly or if the vehicle is involved in an accident. 3.
LUGGAGE COVER: long chassis versions 1 B A 2 To remove the flexible section of the luggage cover Using handle 1, pull it gently to release the pins from their mounting points located on each side of the luggage compartment. Guide the luggage cover onto the roller. Removing the luggage cover Push the luggage cover to the right (movement A) and lift the left-hand side of the inertia reel (movement B).
Luggage compartment storage space and fittings (1/2) 2 1 Side storage compartments 1 Depending on the vehicle, this may be used to hold oil containers etc. Bag hooks 2 Maximum weight per hook: 5 kg. 3 Storage compartment under luggage compartment carpet Depending on the vehicle, to access this, lift the luggage compartment carpet. Partition 3 can be removed. 3.
Luggage compartment storage space and fittings (1/2) 4 5 6 Separating the luggage compartment (depending on the vehicle) The loading area can be separated. Anchorage points Hooks 6 located on each corner of the luggage compartment, allow the load to be secured. Lift divider 4. The elastic band 5 on the back is used to hold objects vertically. Maximum weight: 30 kg, evenly distributed.
Transporting objects in the luggage compartment, towing (towing equipment) A Always place the objects to be transported so that their largest side rests against the back of the rear bench seat, for normal loads (example A) or against the back of the front seats B when the rear bench seatbacks are folded down. If you have to place objects on the folded seat back, it is vital that you remove the headrests before folding the seat back so that it can be folded as flat as possible against the seat.
LUGGAGE NET (1/2) A 1 B 2 4 5 3 Depending on the vehicle, this may be used when transporting animals or luggage to isolate them from the passenger section. It can be positioned: – behind the rear seats A; – behind the front seats B. Fitting the luggage net behind the front seats Inside the vehicle on each side: – attach the two hooks 3 on the net straps 4 to the anchoring points 5; – adjust net strap 4 so that it is taut.
LUGGAGE NET (2/2) 6 7 6 10 11 9 8 Fitting the luggage net behind the rear seats – attach net strap hook 8 to the lower ring; Inside the vehicle on each side: – adjust the position of the second row seats: ensure that the seatbacks do not touch the luggage net. (behind the second row rear seats on the 7-seater version) – push the second row seats fully forward; – lift cover 6 to access the luggage net upper mounting rail; – adjust net strap 9 so that it is taut.
ROOF BARS 1 1 Access to the mounting points Open the doors to access the mounting points 1. For information on the range of equipment adapted to your vehicle, we advise you to consult an approved Dealer. Refer to the fitting instructions for information on how to fit roof bars and conditions of use. Please keep these instructions with the rest of the vehicle documentation. Maximum permissible load on roof rack: refer to the information on “Weights” in Section 6. 3.
multimedia equipment 1 5 4 6 2 A 3 Multimedia systems The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle navigation system version.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level/engine oil change. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Levels:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . engine coolant. . . . . . . . . . . . . . . . .
Bonnet Closing the bonnet Check that nothing has been left in the engine compartment. 2 To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight. 1 To open, pull handle 1, located on the left-hand side of the dashboard. Unlocking the bonnet catch Opening the bonnet Lift the bonnet; you will need to guide it as it is held by a strut. To release it, lift tab 2.
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. B However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
ENGINE OIL LEVEL: topping up/filling (1/2) 1 1 2 Topping up/Filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). Engine oil grade Refer to the Maintenance Service Booklet for your vehicle. Do not exceed the max level and do not forget to refit cap 1 and dipstick 2.
ENGINE OIL LEVEL: topping up/filling (2/2) 1 Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid levels. 2 1 2 Filling: take care when topping up the oil that no oil drips onto engine components - risk of fire. Remember to refit the cap securely as there is a risk of fire if oil splashes onto hot engine components. Oil change Service interval: refer to the Maintenance Service Booklet for your vehicle.
LEVELS (1/3) 1 Checking intervals Replacement intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). Refer to the Maintenance Service Booklet for your vehicle. If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – anticorrosion protection of the cooling system.
LEVELS (2/3) 1 Level 1 Topping up It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI” warning line. After any operation on the hydraulic circuit, a specialist must replace the fluid. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website. Only use fluids approved by our Technical Department (and taken from a sealed container).
LEVELS (3/3)/FILTERS Liquid 1 Windscreen washer fluid. In winter, use anti-freeze product. Jets Use a tool such as a needle to adjust the height of the windscreen washer jets. Filters The replacement of filter elements (air filter, passenger compartment filter, diesel filter, etc.) is scheduled in the maintenance operations for your vehicle. Replacement intervals for filter elements: refer to the Maintenance Service Booklet for your vehicle.
Tyre pressure A B A C D C D E E E E E G H F F F F F I The tyre pressure is indicated on label A affixed to the edge of the driver’s door. Open the door to read it. G: recommended pressure for optimising fuel consumption. B: dimension of the tyres fitted to the vehicle. H: emergency spare wheel dimensions. C: vehicle load. D: intended driving speed. Note: driving comfort may be altered.
Battery 1 Depending on the vehicle, a system continuously checks the battery charge status. If this drops, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. Then the message “Battery charging” appears on the instrument panel for the duration of the charging time.
Bodywork maintenance (1/2) Protection against the effects of corrosive agents Although your vehicle has been treated with very effective anti-corrosion products, it nevertheless remains subject to the effects of: – corrosives in the atmosphere – atmospheric pollution (urban and industrial areas), – saline atmospheres (near the sea, particularly in hot weather), – seasonal and damp climatic conditions, (e.g.: road salt in winter, water from road cleaners, etc.).
Bodywork maintenance (2/2) You should – Wash your car frequently, with the engine off, with cleaning products recommended by our Network (never use abrasive products) and be sure to jet-rinse off: – spots of tree resin and industrial grime; – bird droppings, which cause a chemical reaction with the paint that rapidly discolours paintwork and may even cause the paint to peel off; Wash the vehicle immediately to remove these marks since it is impossible to remove them by polishing; – salt, particularly i
INTERIOR TRIM MAINTENANCE Whatever type of stain is on the trim, use soapy water (if possible, warm water) containing: – natural soap, – washing up liquid (with one part washing up liquid to 200 parts water). Rinse off with a soft, damp cloth. – Seat belts These must be kept clean. Use products selected by our Technical Department (Approved outlets) or warm, soapy water and a sponge and wipe with a dry cloth. Detergents or dyes must not be used under any circumstances.
4.
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit (jack, wheelbrace, etc.). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hubcap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . .
Puncture In case of puncture Depending on the vehicle, a tyre inflation kit or emergency spare wheel is provided (refer to the following pages). Special note The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emergency spare wheel disappears from the instrument panel display). Refer to the information on the “Tyre pressure monitor” in Section 2.
TOOLS/hubcap (1/2) Bolt guide 5 2 For tightening/loosening wheel bolts on vehicles fitted with alloy wheels 1 7 Towing hitch 6 Refer to the information on “Towing” in Section 5. 3 4 5 6 Contents of the wheel change tool kit Wheelbrace 1 Allows the wheel bolts to be locked/unlocked. Jack 2 Fold it correctly before refitting it in its housing (ensure that wheelbrace 3 is correctly positioned). Hubcap tool 4 This tool is used to remove the wheel trims.
TOOLS/hubcap (2/2) 9 D 10 11 B C A 12 Location of the wheel change tool kit 5-seater version Lift luggage compartment carpet 10. Attach it using hook 9. The tools are in kit 11. Wheel trim Remove it using hubcap tool 4 by engaging the hook in the recess provided next to valve 12 (to attach the metal clip). To refit the hubcap, align it with valve 12. Push the retaining hooks in fully, starting with side A near the valve, followed by B and C, finishing at D opposite the valve.
TYRE PRESSURE KIT (1/3) A B Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE PRESSURE KIT (2/3) 1 2 3 – press switch 5 to inflate the tyre to the recommended pressure (check the label affixed to the edge of the driver’s door); 4 C – after a maximum of 7 minutes, stop inflating and read the pressure (on the pressure gauge 4); 5 6 D 7 8 Depending on the vehicle, in the event of a puncture, use the kit located in storage compartment C or underneath luggage compartment carpet D.
TYRE PRESSURE KIT (3/3) – affix driving recommendation label 10 to the dashboard where it can easily be seen by the driver; 4 – store the kit; 10 6 7 Once the tyre is inflated correctly: – stop using the kit; – close the integrated cap on the bottle again; – disconnect the adapter 8; Nothing should be placed around the driver’s feet as such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use.
EMERGENCY SPARE WHEEL 4 2 B 5 1 3 6 A 5 Emergency spare wheel A This is located in the luggage compartment: – open the tailgate; – lift carpet 1 and secure it; – unscrew central mounting 2; – remove the emergency spare wheel. Emergency spare wheel B It is located under the vehicle. In the luggage compartment, lift cover 3 and remove the blanking cover. Using wheelbrace 4, loosen the retaining cable and the wheel will be lowered to the ground.
Changing a wheel If necessary, remove the wheel trim. 3 2 – Unlock the wheel bolts using wheel wrench 3.
Tyres (1/3) Tyre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. You must make sure that your tyres conform to local road traffic regulations. 2 1 When the tyre tread has been worn to the level of the wear indicators, they become visible 2: it is then necessary to replace your tyres because the tread rubber is no more than 1.6 mm deep, resulting in poor roadholding on wet roads.
Tyres (2/3) Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label affixed to the edge of the driver’s door). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey. If tyre pressures cannot be checked when the tyres are cold, the normal pressures must be increased by 0.
Tyres (3/3) Use in winter Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains cannot be fitted to tyres which are larger than those originally fitted to the vehicle. In all cases, we would recommend that you contact an approved dealer who will be able to advise you on the choice of equipment which is most suitable for your vehicle. Snow or Winter tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhesion.
Headlights: changing bulbs (1/2) Daytime running light 1 2 3 A B The bulbs detailed below can be replaced. However, we recommend that these be replaced by an approved Dealer if this proves difficult. (depending on the vehicle) Remove cover B, turn bulb holder 3 to release it then replace the bulb. Daytime running light bulb type: P21LL. Discharge bulb main beam headlights/dipped beam headlights Never open cover A Bulb type: D1S.
Headlights: changing bulbs (2/2) 4 5 6 A B Main beamA/dipped B halogen headlights Removal Remove cover A or B, unclip the bulb by lifting connector 4 or 5 (movement C or D) then replace the bulb. Bulb type: H7. Access to the dipped beam headlight on the battery side 7 C 8 D Refitting Carry out the operations in reverse order. Ensure that the bulb is correctly repositioned (pay attention to the direction of fitting). It is essential to use anti-U.V.
HEADLIGHTS: front fog lights 1 Front fog lights 1 The front bumper needs to be removed; consult an approved Dealer. The bulbs are under pressure and can break when replaced. Any operation on (or modification to) the electrical system must be performed by an approved dealer since an incorrect connection might damage the electrical equipment (harness, components and in particular the alternator). In addition, your Dealer has all the parts required for fitting these units. Risk of injury. 5.
REAR LIGHTS: changing bulbs (1/4) 1 Long chassis version Direction indicator lights/brake and side lights From the luggage compartment, remove the cover and unscrew end piece 1. 2 From the outside, undo screw 2 using a flat-blade screwdriver or similar and pull the light unit towards you. Unclip the bulb holder a quarter of a turn. 3 4 LED lighting The lights are equipped with an LED lighting system as soon as the side lights are switched on. Replace the bulb.
REAR LIGHTS: changing bulbs (2/4) 7 5 6 9 Normal chassis version Unclip the bulb holder by pressing on the tabs 6. 8 Refitting Direction indicator lights and brake lights Replace the bulb. To refit, proceed in the reverse order, taking care not to damage the wiring. From the outside, undo screw 5 using a flat-blade screwdriver or similar and pull the light unit towards you. Direction indicator light 7 Note: do not remove seal 9. Bulb type: PY21W. Side light and brake light 8 Bulb type: P21/5W.
REAR LIGHTS: changing bulbs (3/4) 11 10 Side light From the luggage compartment, unclip the cover. Using a tool, unscrew nut 10. 12 From the outside of the vehicle, pull on the light unit to remove it then unscrew bulb holder 11 a quarter of a turn. Rear fog light and reversing light Replace the bulb. Access bulb holder 12 via the underneath of the vehicle, then unscrew it by turning towards the centre of the vehicle. Bulb type: W5W.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (4/4) 13 A 14 16 15 High level brake light 13 Consult an approved Dealer. Number plate lights 14 Indicator lights 16 Unclip light 14 by pressing tab 15. Unclip indicator light 16 using a flatblade screwdriver or similar. Position it to A to tilt the rear indicator light towards the front of the vehicle. Remove the light cover to gain access to the bulb. Bulb type: C5W festoon bulb. Turn the bulb holder a quarter of a turn and take out the bulb.
INTERIOR LIGHTING: changing bulbs (1/2) 1 A B 2 3 Courtesy light Door lights Sliding central console light – Set the three switches to the central position; Unclip light 2 (using a flat-blade screwdriver or similar). Unclip bulb 3 from its support. – move the courtesy light backwards (movement A) then tilt the front downwards (movement B); Turn the bulb holder a quarter of a turn and take out the bulb.
INTERIOR LIGHTING: changing bulbs (2/2) 5 6 7 4 Luggage compartment lights Unclip lights 4 using a flat-blade screwdriver or similar. Disconnect the light. Press tab 5 to release lens 7 and access bulb 6. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
FUSES (1/2) 3 B A CORRECT INCORRECT Fuse box Tweezers 1 If any electrical component does not work, check the condition of the fuses. Remove the fuse using tweezers 3, located at the back of cover A or B. Unclip cover A or B (depending on vehicle). In accordance with local legislation or as a precautionary measure: Check the fuse in question and replace it, if necessary, by a fuse of the same rating. To remove the fuse from the tweezers, slide the fuse to the side.
FUSES (2/2) 3 7 10 14 4 8 11 15 1 5 9 12 16 2 6 13 17 C 18 19 Allocation of fuses (the presence of certain fuses depends on the vehicle equipment level) 1 Electronic parking brake; 2 Brake lights; 3 Automatic door locking; 4 Driver’s window winder; 5 Instrument panel; 6 Direction indicator lights; 7 Navigation system; 8 Interior rear-view mirror; 9 Rear screen wiper; 10 and 11 Rear electric windows; 12 ABS/ESP; 13 Passenger electric window; Some accessories are protected by fuses locat
Battery: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (courtesy lights, etc.) are switched off before disconnecting or reconnecting the battery; The battery charger must be compatible with a battery with nominal voltage of 12 volts. – when charging, stop the charger before connecting or disconnecting the battery; Do not disconnect the battery when the engine is running.
Battery: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle 2 If you have to use the battery from another vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you already have jump leads, ensure that they are in perfect condition. The two batteries must have an identical nominal voltage of 12 volts.
RENAULT card: battery 2 1 A B 4 3 Replacing the battery When the message “Keycard battery low” appears on the instrument panel, replace the RENAULT card battery, press button 1 pulling on emergency key 2, then unclip the cover 3 using tab 4. Remove the battery by pressing on one side (movement A) and by lifting the other (movement B) then replace it, ensuring the polarity and model, shown on cover 3 are respected.
Fitting a radio 1 2 2 3 3 If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – the radio 1; – tweeter speakers 2; – bass speakers 3. To install any equipment, please consult an approved dealer. Radio location 1 Unclip the blanking cover. The aerial, + and – supply and speaker wire connections are located behind it. – In all cases, it is very important to follow the manufacturer’s instructions carefully.
ACCESSORIES Before fitting an electrical or electronic device (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle. Contact an approved dealer for this information. No work may be carried out on the vehicle’s electrical or radio circuits, except by approved Dealers: an incorrectly connected system may result in damage being caused to the electrical equipment and/or the components connected to it.
wiper blades: replacing 1 Check the condition of the wiper blades. You are responsible for their service life: 4 A B 5 2 3 C Windscreen wiper blades 1 With the ignition on and engine switched off, lower the windscreen wiper stalk completely: they stop slightly away from the bonnet. Lift wiper arm 3, pull tab 2 (movement A) and push the blade upwards. Refitting Slide the blade along the arm until it clips on. Check that it is correctly locked. Return the windscreen wiper stalk to the park position.
Towing: breakdown (1/2) Before towing, unlock the steering column: with the clutch depressed, engage first gear (lever in position N or R for vehicles with automatic transmissions), insert the RENAULT card in the card reader then press the engine start button for two seconds. The speed specified by current legislation for towing must always be observed. If your vehicle is the towing vehicle, do not exceed the maximum towing weight for your vehicle (refer to the information on “Weights” in Section 6).
Towing: breakdown (2/2) – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. 3 4 – A vehicle must not be towed if it is not fit to be driven. 6 5 7 Only use the front 3 and rear towing points 5 (never use the driveshafts). These towing points may only be used for towing: never use them for lifting the vehicle directly or indirectly.
Operating faults (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or unlock the doors. Card battery is flat. Replace the battery. You can still lock/ unlock and start your vehicle (refer to the information on “Locking/unlocking the doors” in Section 1 and “Starting/Stopping the engine” in Section 2).
Operating faults (2/5) The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights are weak or fail to light up and the starter does not turn. Battery terminals not tight, battery terminals disconnected or oxidised. Retighten or reconnect the terminals, or clean them if they are oxidised. Discharged battery or not operational. Connect another battery to the faulty battery.
Operating faults (3/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pressures, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved Dealer. Abnormal white smoke from the exhaust or coolant boiling in the coolant reservoir. Mechanical fault: cylinder head gasket damaged, faulty coolant pump. Stop the engine. Contact an approved dealer. Smoke under the bonnet. Short-circuit or cooling system leak.
Operating faults (4/5) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The coolant temperature indicator is in the warning zone and warning light ® comes on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an approved dealer as soon as possible.
Operating faults (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Blown bulb.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Weights. . . . . . . . . . . . . . . . . .
Vehicle identification plates (1/3) A A 6 7 8 9 10 1 2 3 4 5 11 12 13 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. B Vehicle identification plate A 1 Vehicle type and chassis number. This information is repeated on marking B. 2 Maximum permissible all-up weight. 3 Total train weight (vehicle fully loaded, with trailer). 4 Front axle Maximum permissible weight. 5 Rear axle Maximum permissible weight. Technical specifications of vehicle.
Engine identification plates (2/3) 1 C 2 3 C C The information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. C 6.
Engine identification plates (3/3) 1 C 2 3 C C The information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. C 6.
Dimensions (in metres) Normal chassis versions 0,888 2,702 0,753 1,546 4,343 1,624* 1,547 2,077 * Unladen 6.5 ENG_NU_840-2_JR95_Renault_6 Dimensions dimensions............................................ (up to the end of the DU) technical specifications..........................
Dimensions (in metres) (continued) Long chassis versions 0,888 2,769 0,903 1,536 4,560 1,675* 1,539 * 2,077 Unladen 6.
Engine specifications Versions 1.6 16V 1.4 Tce 2.0 16V 1.5 dCi 1.9 dCi 2.0 dCi Engine type (see engine plate) K4M H4J M4R K9K F9Q M9R Cubic capacity (cc) 1.598 1.395 1.995 1.461 1.870 1.995 Type of fuel Octane Rating Spark plugs It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they may vary depending on your vehicle’s equipment. Consult an approved Dealer.
Replacement parts and repairs RENAULT original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine RENAULT replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer's Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
service sheets (1/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (2/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (3/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (4/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (5/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (6/6) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
Anticorrosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16 ENG_NU_840-2_JR95_Renault_6 Anticorrosion check anti-corrosion check..............................
Anticorrosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
6.
Alphabetical index (1/5) A ABS........................................................................2.20 → 2.22 accessories........................................................................ 5.28 accessories socket............................................................. 3.25 additional methods of restraint......................1.24 → 1.27, 1.30 side protection.............................................................. 1.29 to the rear seat belts.........................................1.
Alphabetical index (2/5) E electric beam height adjustment......................................... 1.76 electric windows.....................................................3.12 → 3.14 electronic parking brake...........................................2.9 → 2.11 Electronic Stability Program: ESP..........................2.20 → 2.22 emergency brake assist.........................................2.20 → 2.22 emergency braking.................................................2.20 → 2.22 emergency key...........
Alphabetical index (3/5) I indicators........................................................ 1.72, 5.13 – 5.14 indicators: direction indicators............................................... 1.72, 5.16 exterior temperature indicator....................................... 1.70 instrument panel...............................................1.51 → 1.68 instrument panel............................................1.51 → 1.68, 1.73 instrument panel messages...................................1.62 → 1.
Alphabetical index (4/5) reference......................................................................... 6.2 parking distance control.........................................2.30 → 2.32 power-assisted steering..................................................... 1.50 puncture...................................................... 5.2 – 5.4, 5.8 – 5.9 R radio................................................................................... 3.42 fitting a radio..............................................
Alphabetical index (5/5) transporting children...............................................1.31 → 1.43 transporting objects in the luggage compartment......................................... 3.38 luggage net........................................................ 3.39 – 3.40 trims............................................................................. 5.3 – 5.4 trip computer and warning system... 1.51 → 1.55, 1.60 → 1.68 tyre inflation kit...........................................................5.
7.
Cyan Magenta Jaune Noir Noir texte 4 SIMPLE ACTIONS* FOR YOUR SAFETY 1 2 • Always fasten your seat belt, – even for short journeys – even if your vehicle is fitted with air bags. • Make sure that all passengers have fastened their seat belts, even in the back. • Always secure children using devices suitable for their size and weight (seat, shell seat, etc.). 3 • Adjust the height of the seat belt according to your size.
Cyan Magenta Jaune Noir Noir texte ( www.e-guide.renault.com ) NU 840-2 – 99 91 099 06R – 02/2009 – Edition anglaise EGuide ENG à999109906Ríïëä 9M NU840-2 | ENG | Dos = 9 mm | 242 pages | C0 M100 J50 N40 | 4 de Couv ENG RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
