Renault KANGOO Z.E.
Welcome to your new electric vehicle This driver’s handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections Getting to know your vehicle ............................... 1 Driving 2 ................................................................... Your comfort ......................................................... 3 Maintenance ......................................................... 4 Practical advice .................................................... ...................................... 6 ...............................................
0.
Section 1: Getting to know your vehicle Electric vehicle: introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Important recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric vehicle: charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRIC VEHICLE: introduction (1/6) 2 1 6 3 4 5 1.
ELECTRIC VEHICLE: introduction (2/6) Electric vehicles have special features, but operate in a similar manner to conventional vehicles. The main difference in electric vehicles is the exclusive use of electric energy instead of fuel, as used in conventional vehicles. 8 7 We therefore recommend that you read these instructions describing your electric vehicle carefully.
ELECTRIC VEHICLE: introduction (3/6) Batteries Traction battery 12 volt battery Your electric vehicle has two types of battery: – a 400V traction battery; – a standard 12V battery, identical to the one used in conventional vehicles. This battery stores the energy necessary to operate the motor in your electric vehicle properly. As with any battery, it discharges after use, and must be regularly recharged.
ELECTRIC VEHICLE: introduction (4/6) A 4 The A symbol identifies the electrical elements in your vehicle which may present health risks. 400 volt electrical circuit The 400V electrical circuit can be recognised by the orange 4 cables and by the elements signalled using the ṑ symbol. The vehicle traction system in an electric vehicle uses an alternating voltage of approximately 400 volts. This system can get hot during and after switching off the ignition.
ELECTRIC VEHICLE: introduction (5/6) Driving Bad weather, flooded roads: As with a car with an automatic gearbox, you will have to get used to not using your left foot, and not using this foot to brake. Do not drive through floods if the depth of water is above the lower edge of the wheel rims.
ELECTRIC VEHICLE: introduction (6/6) Noise Electric vehicles are particularly quiet. You will not yet necessarily be used to it, and neither will other road users. It is difficult for them to hear the vehicle when it is moving. We would therefore recommend that you are aware of the horn and make use of it, especially when driving in a built-up area or when manoeuvring. Please refer to the information on the “Horn” in Section 1.
IMPORTANT RECOMMENDATIONS Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious injury or electric shock which may present a risk to life. In the event of an accident or impact In the event of an accident or an impact to the underside of the vehicle (e.g.: striking a post, raised kerb or other street furniture), this may damage the electric circuit or the traction battery. Have the vehicle checked by an authorised dealer.
ELECTRIC VEHICLE: charging (1/8) 1 2 3 Charging diagram 1 Specific wall socket or recharging terminal 2 Electric charging connection 3 Charging cord If you have any questions regarding the equipment needed for charging, please ask an authorised dealer. 1.
ELECTRIC VEHICLE: charging (2/8) Important recommendations for charging your vehicle Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious injury or electric shocks which could result in death. Charging Do not do anything to the vehicle during charging (washing, working in the engine compartment, etc.).
ELECTRIC VEHICLE: charging (3/8) B B A D C Charging cord A Charging cord B This cord, designed for specific wall sockets or public terminals, enables the standard charge of the traction battery. Depending on the cord, this enables charging: – standard charge, on a socket used only for the vehicle (14A charge); – occasional charge using a domestic socket, when you are not at home, for example (10A charge).
ELECTRIC VEHICLE: charging (4/8) Important recommendations for charging your vehicle Please read these instructions carefully. Failure to follow these instructions may lead to a risk of fire, serious injury or electric shocks which could result in death. Choice of charging cord The standard charging cords supplied with the vehicle have been designed specifically for this vehicle. It is designed to protect you against the risks of electric shock that can lead to death or fire.
ELECTRIC VEHICLE: charging (5/8) 2 Avoid charging and parking your vehicle in extreme temperatures (hot or cold). When the vehicle is parked in temperatures lower than around -25°C, the battery cannot be charged. Note: If in a snowy environment, remove snow from the vehicle charging area before plugging in or disconnecting. Snow in the socket may block the insertion of the charging cord plug.
ELECTRIC VEHICLE: charging (6/8) 7 6 9 5 8 Recharging the traction battery With the ignition off, lever 5 in gear P and opening elements unlocked: – take the charging cord located in the boot of your vehicle; – remove it from its storage bag; – plug in the end of the cord to the power supply (terminal, domestic plug socket, etc.); The charging cord cannot be plugged in or removed while the opening elements are locked. 1.
ELECTRIC VEHICLE: charging (7/8) 7 If the Z.E. warning light 7 lights up red, charging cannot start; restart the charging procedure. If the problem persists, change power supply (terminal, etc.) or consult and approved Dealer. The charging cord is automatically locked with the vehicle. This will make it impossible to unplug the cord from your vehicle. When charging commences, the hazard warning lights will flash five times. A message on the instrument panel indicates the remaining charging time and the Z.
ELECTRIC VEHICLE: charging (8/8) 8 6 9 7 10 Precautions to take when removing from the socket – Press the button 9 on the radio frequency remote control or switch 10 to release the charging cord; – grab the handle 8; – unplug the charging cord from the vehicle. Warning light ṋ goes out on the instrument panel; – close valve 7; Note: Immediately after a long charge of the traction battery, the cord may be hot. Please use the handles.
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) B A 3 2 3 2 1 1 Driver’s responsibility when parking or stopping the vehicle 4 Radio frequency remote control A Radio frequency remote control B 1 Locking all the opening elements. 1 Locking all the opening elements. 2 Unlocking all the opening elements. 3 Coded key for ignition switch, driver’s door and fuel filler cap. 4 Locking/unlocking the luggage compartment and, depending on the vehicle, the sliding side doors.
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surroundings: take care not to lock or unlock the doors by inadvertently pressing the buttons on the remote control. Interference Interference by factors in the immediate vicinity (external installations or the use of equipment operating on the same frequency as the remote control) may affect the operation of the remote control.
KEY, RADIO FREQUENCY REMOTE CONTROL: Use (1/2) A B 1 1 Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone in your vehicle, even for a short time. The doors are locked and unlocked using the remote control unit. It is powered by a battery which must be replaced (refer to the information on the “Key, radio frequency remote control: batteries” in Section 5). Locking the doors Remote control A or B Press locking button 1.
RADIO FREQUENCY REMOTE CONTROL, KEY: use (2/2) A B 2 2 3 Unlocking the doors Remote control A or B Note: unlocking the opening elements will unlock the vehicle charging cord. Press unlocking button 2. Pressing the button briefly unlocks all the doors. A short press on button 3 locks/unlocks the tailgate and, depending on the vehicle, the sliding side doors. The hazard warning lights and side indicator lights flash once to indicate that the doors have unlocked.
DEADLOCKING Special feature For vehicles equipped with deadlocking, when the vehicle is charging, every time one of the doors is unlocked, opened or closed, check that charging is still in progress. 1 1 If not, the charging process needs to be restarted (connecting the cord, programming, etc.). Refer to the paragraph “Electric vehicle: charging” in section 1.
OPENING AND CLOSING THE DOORS (1/4) 2 1 3 Opening from the outside Lights-on reminder buzzer Unlock the door and pull handle 1. For information on unlocking the doors, refer to the information on the “Key, radio frequency remote control: use” in Section 1. A warning beep sounds when the driver’s door is opened to warn you that the lights are still on (to prevent discharge of the 12 volt battery). Opening from the inside Pull handle 2. 1.
OPENING AND CLOSING THE DOORS (2/4) 5 6 Recommendations concerning the sliding side door The following precautions must be taken when opening and closing the doors or any other opening element: – Check that the door will not come into contact with any person, animal or object. 4 – Only use the handles on the inside and outside of the door to operate it.
OPENING AND CLOSING THE DOORS (3/4) 7 Rear hinged doors Opening from the outside Unlock the door and pull handle 7. For information on unlocking the doors, refer to the information on the “Key, radio frequency remote control: use” in Section 1. 8 Opening the doors to the maximum position For each door, pull handle 8 to release the door check strap. Open the door as far as possible. Closing manually from the outside First close the small door and then close the large door.
OPENING AND CLOSING THE DOORS (4/4) 9 10 Rear hinged doors (continued) Opening from the inside (depending on vehicle) Pull handle 10 and open the door. Pull lever 9 to open the small door. Closing from the inside Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time. First close the small door and then close the large door.
CENTRAL DOOR LOCKING, UNLOCKING (1/2) Locking the opening elements without the remote control 1 Control for locking and unlocking from the inside This enables all the doors to be locked simultaneously. Lock or unlock the doors by pressing switch 1. If a door or the tailgate is open or not closed properly, the doors and tailgate lock/unlock quickly. With the engine and ignition off, the sliding side doors closed and a front door open, press switch 1 for more than five seconds.
CENTRAL DOOR LOCKING, UNLOCKING (2/2) 3 2 Manual control Using the key Lock or unlock the driver’s door by inserting the key 3 fully into lock 2, and turning the key. For more information on the remote controls, refer to the information on the “Key, radio frequency remote control: use” in Section 1. Locking the doors manually Turn screw 4 with the door open (using the end of the key) and close the door. This means that the doors are then locked from the outside.
AUTOMATIC LOCKING WHEN DRIVING (RAID) Operating principle When the engine is started, the system automatically locks the doors when the vehicle reaches a speed of approximately 4 mph (7 km/h). 1 Operating faults If you notice an operating fault (automatic locking impossible), first check that all doors are correctly locked. If they are correctly locked and the fault is still present, contact an approved Dealer. You must first decide if you want to activate this function.
FRONT HEADRESTS (1/3) To refit the headrest 1 First, check that the headrest rods are clean and correctly aligned. Pull the tab 2 forwards. A Insert the headrest rods in the holes, with the notches facing forwards (tilt the seat backwards if necessary). Guide the headrest down to the desired height. 2 Headrest A To raise the headrest Pull it upwards to the required height. To lower the headrest Pull the tab 2 forwards, gently lift the headrest to unlock it and guide it down to the required height.
FRONT HEADRESTS (2/3) To remove the headrest Raise it to its highest position. Press button 4 and lift the headrest to release it. Note: when the headrest is removed, take care not to change the positions of the rods. B 3 To refit the headrest 4 Headrest B To raise the headrest Pull it upwards to the required height. To lower the headrest If the setting of the rods has been altered, pull them fully upwards.
FRONT HEADRESTS (3/3) To refit the headrest Press tab 5. 5 C Insert the headrest rods in the holes with the notches facing forward, and guide the headrest down to the required height. 6 Headrest C To raise the headrest Pull it upwards to the required height. To lower the headrest Press tab 5 and guide the headrest down to the desired height. To remove the headrest Raise it to its highest position. Press tabs 5 and 6 then lift the headrest to release it.
FRONT SEATS (1/2) 2 2 1 3 To move forwards or backwards Depending on the seat, lift bar 1 or handle 4 to release it. Release the handle at the desired position and make sure that it is locked. Adjusting the height of the driver’s seat Move lever 3 as many times as necessary: – upwards to raise the seat, – downwards to lower the seat. 1.32 4 To tilt the seatback Depending on the seat, lower or lift lever 2 and tilt the seatback until it reaches the required position.
FRONT SEATS(2/2) 6 Front seats Operating faults (depending on vehicle) If the sliding side door does not work, lower handle 6, hold it while the seatback tilts and slide the seat forwards. To place the seat into the comfort position, slide it rearwards. Adjust the seat and make sure that it is correctly locked. For safety reasons, carry out any adjustments when the vehicle is not being driven. To avoid all risk of injury, ensure that nobody is in the proximity of the moving parts.
ROOF FLAP (1/2) Note: When driving with the roof flap open, you may hear wind noise. To reduce these, open one of the side windows slightly. 1 2 3 To open: Transverse bar – Unlock the control 2, the roof flap lifts automatically (make sure that nothing prevents the flap from opening.
ROOF FLAP (2/2) 1 2 To close: – Unlock the control 2, the roof flap automatically opens halfway; – pull the handle 1 and lock the roof flap in the closed position. Before starting, always reposition the transverse bar and ensure it is correctly locked. The rear hinged doors can only be closed with the bar locked. Remember that the overall vehicle dimensions may change when you are transporting bulky objects. 1.
SWIVELLING PARTITION 2 3 4 1 5 To rotate the partition – Unlock the seat base by moving handle 1 downwards; – lift the front passenger seat base vertically (arrow); – unlock the swivelling section by lifting catch 3; – Pivot the moving section 90 degrees, lock it at point 5 and lower catch 3. – reposition the seat base, proceeding in reverse order. Note: before refitting the swivelling section in its original position, check that locking point 4 is clean.
SEAT BELTS (1/4) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. Adjusting your driving position Make sure that the rear bench seat is securely locked in position so that the rear seat belts will operate efficiently.
SEAT BELTS (2/4) ™ It remains on when the engine is started if your seat belt is not fastened. When the vehicle reaches a speed of 12 mph (20 km/h), the warning light flashes and a buzzer sounds. Then, the beep sounds at a low volume for 30 seconds, then at a high volume for 90 seconds. 1 5 3 4 5 Locking Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pulling on buckle 3).
SEAT BELTS (3/4) Rear side seat belts 8 7 9 Unwind the belt slowly and smoothly and ensure that buckle 8 locks into catch 9 (check that it is locked by pulling on buckle 8). The belts are adjusted in the same way as the front seat belts. 10 Rear centre belt Unwind the belt slowly and ensure that the buckle 7 locks into catch 10. Make sure that the rear bench seat is securely locked in position so that the rear seat belts will operate efficiently.
SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/3) Depending on the vehicle, they will consist of: – seat belt pretensioners; 1 2 – front airbags 1 for driver and front passenger. – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. These systems are designed to act independently or together when the vehicle is subjected to a frontal impact.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/3) Driver and passenger front airbags They are fitted to the front seats on the driver’s side and, depending on the vehicle, on the passenger’s side as well. Depending on the vehicle, the presence of this equipment is indicated by the word “airbag” on the steering wheel and dashboard (airbag zone A) and a symbol on the lower section of the windscreen.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/3) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
SIDE PROTECTION DEVICES Side air bags (depending on vehicle) This air bag may be fitted to each of the front seats and is activated at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. Curtain air bags (depending on vehicle) These airbags may be fitted along the top of each side of the vehicle and are triggered along the front and rear side door windows to protect the passengers in the event of a severe side impact.
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. 1 The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
CHILD SAFETY: General information (1/2) Carrying children Please ensure that you comply with the legislation of your country. Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. Driver’s responsibility when parking or stopping the vehicle A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing.
CHILD SAFETY: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
CHILD SAFETY: choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position for as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. 1.
CHILD SAFETY: choosing a child seat mounting (1/3) The are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
CHILD SAFETY: choosing a child seat mounting (2/3) 4 3 1 2 2 The two rings 1 are located between the seatback and the seat base, behind the zip fasteners, and are identified by a marking. Depending on the vehicle, pass the strap between the wheel arch liner 3 and the underside of the upper partition 4. The third ring is used to attach the upper strap on some child seats. From the luggage compartment, attach the strap hook to ring 2 on the corresponding side.
CHILD SAFETY: choosing a child seat mounting (3/3) The ISOFIX anchorage points have been exclusively designed for child seats with the ISOFIX system. Never fit a different type of child seat, seat belt or other objects to these anchorage points. Check that nothing is obstructing the anchorage points. If your vehicle has been involved in a road accident, have the ISOFIX anchorage points checked and replace your child seat. The child seat strap must be attached to the corresponding ring.
CHILD SAFETY: fitting a child seat (1/6) Some seats are not suitable for fitting child seats. The diagrams on the following pages show you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. In the front seat The laws concerning children travelling in the front passenger seat differ in every country.
CHILD SAFETY: fitting a child seat (2/6) In the rear seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest the door. Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will go, although without allowing it to come into contact with the child seat.
CHILD SAFETY: fitting a child seat (3/6) 2-seat version Child seat attached using the belt ¬ Seat which allows a child seat with “Universal” approval to be attached by a seat belt. ² ³ seats. Seat not suitable for fitting child Check the status of the front airbag before fitting a child seat or allowing a passenger to use the seat. (1) Before fitting a child seat: position the vehicle seat as far back as possible.
CHILD SAFETY: fitting a child seat (4/6) 5-seat version Child seats attached using the ISOFIX mounting ü ³ Seat which allows an ISOFIX. child seat to be fitted. Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. ² ± seats. Child seat attached using the belt ¬ Seat which allows a standardised “Universal” seat to be fitted using a seat belt; − Seat which only allows a rearfacing standardised “Universal” seat to be installed using a seat belt.
CHILD SAFETY: fitting a child seat (5/6) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
CHILD SAFETY: fitting a child seat (6/6) X = Seat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted.
CHILD SAFETY: deactivating, activating the front passenger airbag (1/3) 2 1 Deactivating the front passenger airbags (on equipped vehicles) Before fitting a child seat on the front passenger seat you must deactivate the passenger airbag. To deactivate the airbags: with the vehicle stationary and the ignition off, press and turn lock 1 to the OFF position.
CHILD SAFETY: deactivating, activating the front passenger airbag (2/3) A A 3 DANGER The marking on the dashboard and label A on each side of the passenger sun visor 3 (example of label shown above) remind you of these instructions. Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child restraint system in a seat protected by an ACTIVATED front AIRBAG . This can lead to the DEATH of the CHILD or SERIOUS INJURY. 1.
CHILD SAFETY: deactivating, activating the front passenger airbag (3/3) 2 Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child restraint system in a seat protected by an ACTIVATED front AIRBAG. This can lead to the DEATH of the CHILD or SERIOUS INJURY.
STEERING WHEEL/POWER-ASSISTED STEERING Power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. 1 Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).
DRIVING POSITION, LEFT-HAND DRIVE (1/2) 1 26 25 2 3 4 24 23 22 5 6 7 8 17 16 21 20 18 19 1.
DRIVING POSITION, LEFT-HAND DRIVER (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Stalk for: – direction indicator lights; – exterior lights; – front fog lights; – rear fog lights. 2 – Horn, – location for driver’s air bag. 3 Instrument panel. 4 Stalk for: – windscreen wipers; – windscreen washer; – trip computer and warning system. 5 Ignition switch.
DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 1 2 3 4 5 6 7 8 10 9 11 12 13 29 28 27 26 25 21 24 23 1.
DRIVING POSITION: RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side window demister outlet. 2 Side air vent. 3 Speaker. 4 Location for passenger air bag. 5 Windscreen demister outlet. 6 Controls for ventilation, heating and de-icing. 7 Centre air vent. 8 Multimedia display or touchscreen: – seat belt reminder warning light; – airbag deactivation warning light; – navigation; – clock; – exterior temperature.
WARNING LIGHTS (1/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A Instrument panel A In some cases, the appearance of a warning light is accompanied by a message. Warning light ® requires you to stop immediately, for your own safety, as soon as traffic conditions allow. Switch off the engine and do not restart it. Contact an approved Dealer. 1.
WARNING LIGHTS (2/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Brake circuit fault warning light If it comes on during braking and is accompanied by the ® warning light and a beep, it indicates that the fluid level in the circuit is low or that there is a braking system fault. Stop as soon as traffic conditions allow and contact an approved Dealer.
WARNING LIGHTS (3/3) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. Electrotechnical system warning light When the blue warning light comes on, this indicates that the traction battery temperature is too low. When the orange warning light comes on, this means the traction battery or the motor temperature is too high. If either of these warning lights come on, this may lead to reduced vehicle performance. Opt for a calmer driving style.
DISPLAYS AND INDICATORS (1/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. Charge level 3 The gauge indicates the level of energy remaining. 1 3 2 5 Speedometer 1 Vehicle speed is limited to approximately 80 mph (130 km/h). Depending on your vehicle, this speed can be permanently limited to a set value.
DISPLAYS AND INDICATORS (2/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. B A C 6 6 Charge meter 6 Please refer to the information on the “Charge meter” in Section 2. “Energy recovery” usage zone A The needle tells you that the vehicle is generating energy and the traction battery is being recharged (under braking or going downhill).
DISPLAYS AND INDICATORS (3/3) The presence and operation of the display and indicators DEPENDS ON THE LEVEL OF EQUIPMENT AND THE COUNTRY. – Display selection 5 Press briefly to move from the total mileage to the trip mileage and vice versa. – Resetting the trip mileage recorder Once trip mileage has been selected on the display, press and hold the button. Multifunction display 6 Total mileage recorder. Trip mileage recorder. Setting the time.
TRIP COMPUTER: general information (1/2) a) Total mileage and trip mileage recorder; 1 2 A b) journey parameters: – Total energy consumption since the last reset; – average energy consumption; – current energy consumption; – Total energy consumption since the vehicle first entered into service; – estimated range; – distance travelled; – average speed.
TRIP COMPUTER: general information (2/2) Automatic resetting of the journey parameters 1 Resetting occurs automatically when the maximum value of any of the parameters is exceeded. Resetting the estimated range 2 Trip mileage resetting With “trip mileage recorder” selected on the display, press button 1 or 2 until the mileage recorder resets to zero. Resetting the journey parameters (reset button) Press and hold one of the buttons 1 or 2.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (1/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km a) Total mileage and trip mileage recorder. 112,4 km CONSUMPTION 20 kWh b) Journey parameters. Energy consumed since the last reset. AVERAGE 18,5 kWh/100km Average energy consumption since the last reset. The value is displayed after having travelled at least 400 metres since the last reset.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (2/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected RANGE Estimated range with remaining energy. 118 km The information disappears when the battery is at less than approximately 4%. DISTANCE 522 km Distance travelled since the last reset. AVERAGE 48 km/h Average speed since the last reset. The value is displayed after driving 400 metres.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (3/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections SERVICE IN 1936 km Interpreting the display selected c) Service interval.
TRIP COMPUTER AND WARNING SYSTEM: journey parameters (4/4) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected SPEED LIMITER 90 km/h e) Cruise control/speed limiter programmed speed. CRUISE CONTROL Refer to the information on the “Speed limiter” and “Cruise control” in Section 2. 90 km/h 1.
TRIP COMPUTER AND WARNING SYSTEM: information messages Information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpretation of messages “CHARGE REMAIN 02:10” Indicates the time remaining before a full charge. “NO MESSAGE AVAILABLE” No warning is stored. “BRAKE THE VEHICLE” Follow these instructions: risk of damage to the motor.
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an approved Dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given on the following pages.
TRIP COMPUTER AND WARNING SYSTEM: warning message These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
CLOCK AND EXTERIOR TEMPERATURE After two seconds, the hours and minutes start flashing. A Press and hold the bottom button to enter the hour setting mode. 1 When only the hours flash, press the top button to scroll through them. Exterior temperature On equipped vehicles, the exterior temperature is displayed at A. If it is between -3°C and +3°C, the °C characters flash (signalling a risk of ice). Press and hold the bottom button to enter the minute setting mode.
REAR-VIEW MIRRORS Heated door mirrors When the engine is started, mirror deicing is activated with the rear screen de-icing/demisting. Folding door mirrors A 2 Move button 2 to position D to fold the door mirrors in. To reset them for driving, return to position B. B 1 D Interior rear view mirror The interior rear view mirror is adjustable. When driving at night, tilt lever 1 to avoid being dazzled by the headlights of the vehicle behind.
AUDIBLE AND VISUAL SIGNALS 1 1 0 3 2 Horn Press one of points 2. Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn. When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0. There is an intermediate position in which the switch may be held when changing lanes. You can also briefly place stalk 1 in the intermediate position, causing the indicator light to flash three times.
PEDESTRIAN HORN Electric vehicles are particularly quiet. This system enables you to warn people of your presence – especially pedestrians and cyclists. Warning noise selection – Keep the switch 1 depressed. The various sounds will be played in succession; 1 The system is activated automatically when the engine is started. The sound triggers when the vehicle speed is between 1 and 20 mph (1 and 30 km/h). – release the switch 1 on the sound of your choice.
EXTERNAL LIGHTING AND SIGNALS (1/3) k 1 2 Dipped beam headlights Manual operation Turn the end of stalk 1 until the symbol is opposite mark 2. This indicator light on the instrument panel comes on. Automatic operation (depending on vehicle) 3 u Side lights Turn the end of stalk 1 until the symbol is opposite mark 2. The instrument panel will light up. á Main beam headlights With stalk 1 in dipped beam headlights position, move the stalk towards you.
EXTERNAL LIGHTING AND SIGNALS (2/3) “See-me-home lighting” function Lights-on reminder buzzer 1 (depending on vehicle) 2 This function (useful, for example, when opening a gate, garage, etc.) enables you to switch the dipped headlights on momentarily. With the ignition off and the headlights off, pull stalk 1 towards you: the dipped beam headlights come on for approximately sixty seconds. This action may be carried out no more than four times for a maximum lighting period of four minutes.
EXTERNAL LIGHTING AND SIGNALS (3/3) f 1 4 Rear fog light The front fog lights and the side lights or dipped beam headlights must be on. Turn ring 5 on stalk 1 until the symbol is opposite mark 4, then release it. This indicator light on the instrument panel comes on. 5 To avoid inconveniencing other road users, remember to switch off the rear fog light when it is no longer needed.
HEADLIGHT BEAM ADJUSTMENT (1/2) 1 A B 100 m Control knob 1 is used to adjust the height of the headlight beams according to the load. Turn control knob 1 downwards to lower the headlights and upwards to raise them. Unladen, control knob 1 should be at 0. When the vehicle is partially or completely laden, the headlight beam should be set to light the road at between 50 and 100 metres. Then use positions 1 to 4 on the control knob. 1.
HEADLIGHT BEAM ADJUSTMENT (2/2) When driving on the left in a lefthand drive vehicle (or vice versa), you must adjust your lights temporarily during your stay. B 1 Temporary adjustment Open the bonnet and identify the marking B next to one of the front headlight projectors. For each headlight, using a screwdriver, turn the screw 1 by a quarter turn towards the - symbol to lower the beams.
FRONT WINDSCREEN WASHER, WIPER (1/2) Automatic wiper function (depending on vehicle) With the engine running, move stalk 1. 1 A Park A B C D 2 Windscreen wiper Special note With the ignition on, move stalk 1 parallel to the steering wheel: When the vehicle is being driven, the wiping speed slows down whenever the vehicle stops. For example, fast wiping speed will slow to normal wiping speed. As soon as the vehicle moves off, wiping will return to the speed originally selected.
FRONT WINDSCREEN WASHER, WIPER (2/2) 1 Efficiency of a wiper blade Check the condition of the wiper blades. How long they last depends on you: Windscreen wiper With the ignition on, pull stalk 1 towards you. A brief pull will trigger a single sweep of the wipers, in addition to the windscreen washer. A longer pull will trigger three sweeps of the wipers followed, a few seconds later, by a fourth, in addition to the windscreen washer.
REAR WINDSCREEN WASHER, WIPER p 1 Rear screen wash/wipe (depending on vehicle) Turn the end of stalk 1 to position the symbol opposite mark 2. When the stalk is released, it returns to the rear screen wiper position. timer Speed-dependent rear screen wiper with (depending on vehicle) Turn the end of stalk 1 to position the symbol opposite mark 2. Do not use the wiper arm to open or close the tailgate. Wiping frequency varies with speed.
ADDITIONAL HEATING TANK Fuel grade Use a high-grade fuel that complies with the legislation in force in each country and which must conform to the specifications given on the label on cover A. A B Fuel odours and smoke may be present after a long period without using the additional heating. C Useful capacity of fuel tank: 13 litres approx. To open the fuel filler flap, place your finger into recess C. Use the ignition key to open cap B.
1.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Starting, stopping the engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gear control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Handbrake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING, STOPPING THE ENGINE (1/2) “On” position M The ignition is switched on: Start position D Starting the engine 1 – Move lever 1 to position P only ; – turn the key to position D and then release it. Warning light Ṑ may flash on the instrument panel, along with a beep. As soon as light Ṑ stops flashing and the beep stops, the vehicle is ready to drive. “Stop and steering lock” position St To unlock: turn the key and the steering wheel slightly.
STARTING, STOPPING THE ENGINE (2/2) Stopping the engine With the engine running, turn the key back to the “Stop” position St. Warning light Ṑ goes out. Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone in your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, activating equipment such as the electric windows or locking the doors, for example.
GEAR CONTROL (1/2) Driving Put lever 1 in position D. A Hill start For hill starts, especially after a maximum traction battery charge and for the first few miles, we recommend using the handbrake. 1 3 2 While driving, press the accelerator pedal to achieve the desired speed. Reverse Put lever 1 in position R. Operates similar to an automatic gearbox. Selector lever 1 The display A on instrument panel indicates the gear lever position as 3. P: Park R: Reverse N: Neutral D: Forward 2.
GEAR CONTROL (2/2)/HANDBRAKE Parking the vehicle Handbrake When the vehicle is stopped, move the lever to position P while keeping your foot on the brake pedal: the gearbox is in neutral and the drive wheels are mechanically locked by the driveshaft. To release: Pull the lever 5 up slightly, press button 6 and then lower the lever to the floor. 4 Apply the handbrake. To apply: Pull upwards, check that the vehicle is properly immobilised. In the event an impact to the underside of the vehicle (e.g.
DRIVING ADVICE, ECO-DRIVING (1/2) The vehicle range depends on vehicle usage conditions, equipment fitted and the user’s driving style. To optimise the energy consumption, please refer to the following advice. Depending on the vehicle, you will be provided with functions which enable you to lower the energy consumption: – ECO mode, activated by the ECO button; – charge meter. 2 1 ECO mode The ECO function optimises vehicle range by limiting engine performance.
DRIVING ADVICE, ECO-DRIVING (2/2) 0 A B C A Charge meter (on the instrument panel) The charge meter gives the driver a real-time view of the vehicle’s energy recovery or consumption. “Energy recovery” usage zone A When driving, if you lift your foot off the accelerator pedal or apply the brake, the motor generates electrical current during deceleration, and this energy is used to slow down the vehicle and recharge the traction battery.
VEHICLE RANGE: recommendations (1/2) The vehicle range is approved for a mixed NEDC cycle (New European Driving Cycle). In real usage, the range of an electric vehicle may vary depending on several factors over which you have partial control, which may make a considerable difference to the vehicle range. These factors are: – speed and driving style; – type of road; – heating level; – tyres; – vehicle loading.
VEHICLE RANGE: recommendations (2/2) Vehicle loading Avoid pointlessly overloading your vehicle. Heating levels Tyres The use of heating or air conditioning reduces vehicle range. Before using the vehicle, opt for “air conditioning programming” mode to maintain vehicle range (please refer to the information on “Heating, air conditioning programming” in Section 3).
ENVIRONMENT Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the of the manufacturer eco² signature. Emissions Manufacture Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
TYRE PRESSURE LOSS WARNING (1/4) Resetting the standard level for the tyre pressures 1 This should be done: – when the standard tyre pressure needs to be changed to adapt to usage conditions (empty, carrying a load, motorway driving, etc.); – after swapping a wheel (however this practice is not recommended); – after changing a wheel. It should always be done after checking the tyre pressure of all four tyres when cold.
TYRE PRESSURE LOSS WARNING (2/4) The display of the message “TP ACQUISTION LAUNCHED” for around five seconds indicates that the reset request for the tyre pressure reference value has been taken into account. 2 3 4 Resetting procedure With the ignition on, depending on the vehicle: – repeatedly press one of the buttons 3 or 4 to select the “TYRE PRESSURE ACQUISITION” function on the display 2; – press and hold (around 3 seconds) button 3 or 4 to start initialisation. 2.
TYRE PRESSURE LOSS WARNING (3/4) Display TYRE PUNCTURE The display 2 on the instrument panel informs you of any tyre pressure faults (flat tyre, punctured tyre, etc.). CHECK TYRE PRESSURES stays on The warning light and, depending on the vehicle, along with the message “CHECK TYRE PRESSURES”. These indicate that at least one tyre is flat. Check and, if necessary, readjust the pressures of the four wheels when cold. The warning light few minutes’ driving.
TYRE PRESSURE LOSS WARNING (4/4) Readjustment of tyre pressures The tyre pressures must be adjusted when cold (please refer to the label located on the edge of the driver’s door). If tyre pressures cannot be checked when the tyres are cold, the recommended pressures must be increased by 0.2 to 0.3 bar (3 PSI). Never deflate a hot tyre. Replacing wheels/tyres This system requires specific equipment (wheels, tyres, hubcaps, etc.). Please see the information on “Tyres” in Section 5.
DRIVER CORRECTION DEVICES AND AIDS (1/3) Depending on the vehicle, this is composed of: – of the ABS (anti-lock braking system); – electronic stability program (ESC) with understeer control and traction control; – emergency brake assist; – hill start assistance. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions. However, the functions do not take the place of the driver.
DRIVER CORRECTION DEVICES AND AIDS (2/3) Electronic stability program ESC with understeer control and traction control Electronic stability control ESC This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
DRIVER CORRECTION DEVICES AND AIDS (3/3) Emergency brake assist This is an additional system to ABS which helps reduce vehicle stopping distances. Operating principle The system detects an emergency braking situation. In this case, the braking assistance immediately develops maximum power and may trigger ABS regulation. ABS braking is maintained as long as the brake pedal is not released. Hazard warning lights switching on Depending on the vehicle, these may light up in the event of sudden deceleration.
SPEED LIMITER (1/3) 1 2 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. 3 4 5 Controls Switching on 1 Main “On/Off” switch. Press the side switch 1 . Warning light comes on, lit orange, and the “SPEED LIMITER” message appears on the instrument panel, accompanied by dashes to indicate that the speed limiter function is activated and waiting to store a limit speed.
SPEED LIMITER (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by repeatedly pressing: It is possible to exceed the limit speed at any moment. To do this: press the accelerator pedal firmly and fully (beyond the resistance point). – switch 2 (+) to increase the speed; – switch 3 (-) to decrease the speed. 2 3 4 5 Whilst the speed is being exceeded, the cruising speed displayed on the instrument panel flashes.
SPEED LIMITER (3/3) Recalling the limit speed If a speed has been stored, it can be recalled by pressing switch 5 (R). 1 2 3 4 5 Putting the function on standby Switching off the function The speed limiter function is deactivated when you press switch 1. In this case, the speed is no longer stored. The orange instrument panel warning light goes out, confirming that the function is stopped. The speed limiter function is suspended when you press switch 4 (O).
CRUISE CONTROL (1/4) 1 2 3 4 5 This function is an additional driving aid. The function does not take the place of the driver. The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 18 mph (30 km/h). Therefore, it can under no circumstances replace the driver’s responsibility to respect speed limits and to be vigilant (the driver must always be ready to brake).
CRUISE CONTROL (2/4) 1 2 6 Switching on Press switch 1 side . Indicator light 6 comes on, lit green, and the message “CRUISE CONTROL” appears on the instrument panel, accompanied by dashes to indicate that the cruise control function is activated and waiting to store a cruising speed. 4 5 7 Activating cruise control At a steady speed (above 18 mph (30 km/h approximately)) press switch 2 or (+): the function is activated and the current speed is saved.
CRUISE CONTROL (3/4) Exceeding the cruising speed 2 3 4 5 The cruising speed may be exceeded at any time by depressing the accelerator pedal. While it is being exceeded, the cruising speed flashes on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automatically return to its set cruising speed.
CRUISE CONTROL (4/4) Recalling the cruising speed 2 3 4 5 If a speed has been stored, it can be recalled by pressing button 5 (R), on condition that you are driving faster than approximately 20 mph (30 km/h) and that you are sure that the driving conditions are suitable (traffic, road surface condition, weather conditions, etc.). 1 NB: if the speed previously stored is much higher than the current speed, the vehicle will accelerate more rapidly to reach this threshold.
PARKING DISTANCE CONTROL (1/2) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the vehicle and an obstacle. 1 This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 30 centimetres from the obstacle. NB: make sure that the ultrasonic sensors are not obscured (by dirt, mud, snow, etc.).
PARKING DISTANCE CONTROL (2/2) Prolonged deactivation of the system You can deactivate the system permanently by pressing and holding switch 2. The warning light built into the switch remains lit constantly. Pressing the switch again will reactivate the system and switch off the indicator light. 2 Temporary deactivation of the system (depending on vehicle) Press switch 2 to deactivate the system: The indicator light built into the switch lights up to remind you that the system is deactivated.
REVERSING CAMERA (1/2) 3 1 Operation Moving into reverse gear, the camera 1 located on the rear hinged door provides a view of the area behind the vehicle on the rear-view mirror 2 or, depending on the vehicle, on the multimedia display 3, accompanied by one or two (moving and fixed) guide lines 4 and 5. 2 Note: make sure that the reversing camera is not obscured (by dirt, mud, snow, condensation, etc.). Note: depending on the vehicle, you can adjust certain settings from the multimedia display 3.
REVERSING CAMERA (2/2) 4 5 C B This gauge remains fixed and indicates the vehicle trajectory if the wheels are in line with the vehicle. This system is initially used with the aid of several gauges (mobile for trajectory and fixed for distance). When the red zone is reached, use the bumper image to stop accurately. A The screen shows a reverse image. Dynamic gauge 4 (depending on the vehicle) This is shown in blue on the multimedia display 3.
Section 3: Your comfort Air vents: air outlets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heating, air-conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Additional heating . . . . . . . . . . . . . . . . . . . . . . .
AIR VENTS: air outlets (1/2) 1 2 3 5 4 2 6 1 5 1 Demister outlets, side windows. 4 Centre air vents. 2 Side air vents. 5 Footwell vents. 3 Demisting outlets for the windscreen. 6 Control panel 3.
AIR VENTS: air outlets (2/2) To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. 7 9 8 10 Centre air vents Side air vents Settings Settings Air flow: Air flow: Move the control knob 7 (beyond the resistance point). Move the control knob 10 (beyond the resistance point). Air distribution: Air distribution: Right/left: move tabs 8. Right/left: move tab 9. Up/down: guide the air vent up or down.
HEATING, AIR-CONDITIONING (1/4) 2 1 3 4 Switching air conditioning on or off The air conditioning is switched on (indicator light illuminated) or off (indicator light extinguished) using button 6. The air conditioning system is used for: – lowering the temperature inside the passenger compartment; – eliminating condensation more quickly. 7 6 The controls The controls depend on the vehicle equipment. 1 - Air recirculation control.
HEATING, AIR-CONDITIONING (2/4) 2 4 The air flow is directed to the windscreen demisting vents, the side windows and the passenger footwells. This is the recommended position for the best temperature in cold weather. i ó G The air flow is directed mainly towards the footwells. The air flow is directed to all air vents and the footwells. This is the recommended position for the best temperature in hot weather. J Adjusting the air temperature Turn control 2 to obtain the desired temperature.
HEATING, AIR-CONDITIONING (3/4) 3 6 Adjusting the ventilation speed Position 0 Normal use – heating or air conditioning stops automatically even if button 6 is activated and the warning light remains lit; Turn control 3 to one of the four positions to start the ventilation system and adjust the power. Select position 1 for minimum ventilation and position 4 for maximum ventilation.
HEATING, AIR-CONDITIONING (4/4) 1 Air recirculation (isolation of the passenger compartment) Turn control 1 towards the air recircula- K . tion symbol In these conditions air is taken from the passenger compartment and is recirculated, with no air being taken from outside the vehicle. Air recirculation operates as follows: – isolating the passenger compartment from the outside air (driving in polluted areas, unpleasant odours, etc.
AIR CONDITIONING, HEATING: programming (1/2) Note: depending on the power of the charging terminal, a slight reduction in the charge level is possible when the function is activated. 1 A B 2 3 Adjusting the programming Operating conditions This function enables the electric network (and the not the traction battery) to be used under certain conditions, in order to obtain a comfortable temperature prior to using the vehicle.
AIR CONDITIONING, HEATING: programming (2/2) – hold down button D on stalk 5 - the minutes flash; 4 – press button C to adjust them; C D 5 Setting the start time for the function – To programme the start time, use buttons C and D to navigate through the menu until message COMFORT PROG appears. – hold down button D on stalk 5 - the hours flash; – press button C to adjust them; – confirm by pressing button D on stalk 5.
ADDITIONAL HEATING (1/2) 1 2 4 3 Depending on the vehicle, the additional heating is designed to heat the passenger compartment. Powered by a dedicated fuel tank (please see “Additional heating tank” in Section 1), this increases the comfort level without reducing vehicle range. Switching on this additional heating deactivates other heating methods and the air-conditioning.
ADDITIONAL HEATING (2/2) Operating fault If the additional heating does not switch on: – start the vehicle; – switch on the heating by pressing switch 4; 4 – wait for 5 minutes; – turn off the heater; – switch off your vehicle ignition; – restart the operation 4 or 5 times. Operating principle If the additional heating still fails to operate, please contact an authorised dealer. With the engine running, press switch 4.
AIR CONDITIONING: information and operating instructions (1/2) Range Operating faults It is normal to notice an increase in energy usage when the air conditioning is operating. Switch off the system when it is not required. As a general rule, contact your approved Dealer in the event of an operating fault. – Reduction in de-icing, demisting or air conditioning performance. This may be caused by the passenger compartment filter cartridge becoming clogged. – No cold air is being produced.
AIR CONDITIONING: information and operating instructions (2/2) A A A Ñ Type of refrigerant fluid Type of oil in the air conditioning circuit Inflammable product Consult the driver’s handbook Maintenance Quantity of refrigerant x.xxx kg fluid present in the vehicle. The refrigerant circuit may contain fluorinated greenhouse gases. Depending on the vehicle, you will find the following information on label A affixed inside the engine compartment.
MULTIMEDIA EQUIPMENT 1 5 2 3 4 The presence and location of this equipment depends on the vehicle’s multimedia equipment. 1 Multimedia touchscreen; 2 multimedia sockets; 3 radio; 4 steering column control; 5 microphone. To operate this equipment: please refer to the instructions for the equipment which should be kept with the other vehicle documentation. 3.
INTERIOR LIGHTING Special features 1 2 Depending on the vehicle, remote unlocking of the doors triggers timed lighting of the passenger compartment. If one of the front or rear doors is opened, the period for which the light is switched on will start again. Then the courtesy light and the luggage compartment light dim and go out.
SUN VISOR/MIRRORS 1 2 Front sun visor Lower sun visor 1. The clip can be used to hold motorway passes, etc.. Courtesy mirror 2 (passenger side) If the sun visor is fitted with a courtesy mirror, it has a cover. When driving, ensure the courtesy mirror cover is closed. Risk of injury. 3.
ELECTRIC WINDOWS One-touch electric window (depending on vehicle) 1 3 2 The one-touch mode works in addition to the operation of the electric windows described previously. It is fitted to the driver’s window and is used for lowering only. Briefly press switch 1: the window will open completely. Pressing the switch again while the window is moving will stop its movement.
ASHTRAYS, CIGARETTE LIGHTER, ACCESSORIES SOCKETS Cigarette lighter 2 With the ignition on, press it in. It will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in. 1 2 Removable ashtray 1 This is a removable ashtray which can be placed in the cup holders. Accessories sockets You can use the cigarette lighter socket2.
PASSENGER COMPARTMENT STORAGE, FITTINGS (1/3) 3 1 2 Glovebox To open the glovebox, lift catch 1. Dashboard storage compartment 2 Centre console storage compartment 3 To open, lift cover 4. It will store a 1.5 litre bottle. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. 4 There is a risk of burning if hot liquid escapes. 3.
PASSENGER COMPARTMENT STORAGE, FITTINGS (2/3) 6 7 5 8 Front door storage compartments 5 Front upper cab storage compartment 7 Bottle holders 6 No object should be placed on the floor (in front of the driver). Such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use. 3.20 Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning or braking.
PASSENGER COMPARTMENT STORAGE, FITTINGS (3/3) 9 9 Clothes hook 9 Depending on the vehicle, a hook may be located on the partition behind the front passenger seat. For safety reasons, this hook may only be used to hang clothes. NB: the maximum permitted load is 4 kg. 3.
REAR HEADRESTS 1 To raise it Slide it to the required height. To lower it Pull it towards you and slide it to the required height. 2 Storage position 2 Pull it towards you and lower it completely. The fully lowered headrest position is a storage position: it should not be in this position when a seat is occupied. To remove it Raise the headrest then press tabs 1 to release it. To refit it Press tab 1 and insert the rods into the holes, with the notches facing forwards. 3.
REAR BENCH SEAT: functions (1/2) Before folding down any rear seat, fasten the seat belt buckle of the seat concerned into its corresponding catch. This will prevent the seat belt becoming trapped when the seat is returned to its position for use. 1 In all cases, check that the seat belts are operating correctly.
REAR BENCH SEAT: functions (2/2) To raise the seatback Use restriction Before raising the seatback, make sure there are no objects (water bottle, tool box etc.) which will prevent it from locking properly. It is forbidden to drive with a seatback or a front seat folded down when there is a passenger occupying a rear seat. Raise the seatback and click it into position. Check that it is correctly locked. When refitting the seatback, make sure it is correctly locked.
TRANSPORTING OBJECTS IN THE BOOT (1/2) Always position the objects transported so that the largest surface is against: – the rear bench seatbacks, for normal loads; – the front seats for maximum loads. Always position the heaviest items directly on the floor. Always position the heaviest items directly on the floor. Use the lashing points on the floor of the luggage compartment, if these are fitted to the vehicle.
TRANSPORTING OBJECTS IN THE BOOT (2/2)/TOWING A A = 784 mm. Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. Choice and fitting of towing equipment Maximum weight of towing equipment: 24 kg For fitting and conditions of use, refer to the equipment’s fitting instructions. Please keep these instructions with the rest of the vehicle documentation. 3.
Section 4: Maintenance Bonnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . brake fluid . . . . . . . . . . . . . . . . .
BONNET (1/2) 2 1 To open the bonnet, pull the handle 1. Unlocking the bonnet catch To open, push tab 2 to the left as you open the bonnet. Opening the bonnet Please note when working close to the engine that it may be hot. The engine cooling fan may also start Lift the bonnet, helping it up, and it will rest in position with the help of struts. at any moment. The warning light in the engine compartment reminds you of this. Risk of injury. 4.
BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and lower it to 30 cm above the closed position, then release it. After carrying out any work in the engine compartment, check that nothing has been left behind (cloth, tools, etc.). These may damage the engine or cause a fire. Ensure that the bonnet is properly locked. Check that nothing is preventing the catch from locking (gravel, cloth, etc.).
LEVELS (1/2) Replacement intervals Refer to the Maintenance Document for your vehicle. 2 1 Please note when working close to the engine that it may be hot. The engine cooling fan may also start Coolant With the engine switched off and on level ground, the level when cold must be between the “MINI” and “MAXI” marks on the coolant reservoir 1 and 2. Top this level up when cold before it reaches the MIN mark.
LEVELS (2/2) Level 3 It is normal for the level to drop as the linings become worn, but it should never drop below the “MINI” warning line. 3 If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website. 4 Topping up After any operation on the hydraulic circuit, a specialist must replace the fluid.
12 VOLT BATTERY (1/2) 1 Maintenance/replacement Refer to the Maintenance Document for your vehicle. Never open the battery cover 1. The charge status of the 12V battery can decrease, especially if you use your vehicle: – when the exterior temperature drops; – after extended use of energy-consuming devices (radio etc.) with the engine switched off. 4.6 For your own safety and for the proper operation of the vehicle’s electrical equipment (lights, windscreen wipers, ABS, etc.
12 VOLT BATTERY (2/2) A 2 3 4 7 6 5 Label A Observe the indications on the battery: – 2 naked flames and smoking are forbidden; – 3 eye protection required; – 4 keep away from children; – 5 explosive materials; – 6 refer to the handbook; – 7 corrosive materials. Do not do any work under the bonnet when the vehicle is charging or when the ignition is switched on. Please note when working close to the engine that it may be hot. The engine cooling fan may also start at any moment.
TYRE PRESSURE (1/2) Vehicle fitted with a tyre pressure loss warning system A If under-inflated (puncture, low pres- sure, etc.), the warning light lights up on the instrument panel. See “Tyre pressure loss warning” in Section 2. A Label A Open the driver’s door to read it. Tyre pressures should be checked when the tyres are cold. If the tyre pressures cannot be checked when the tyres are cold, increase the pressures from 0.2 to 0.3 bar (or 3 PSI). Never deflate a hot tyre.
TYRE PRESSURES (2/2) Tyre safety and use of snow chains: Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains. For your safety, please respect the speed limit. When they need to be replaced, only tyres of the same make, size, type and profile should be used on a single axle. They must: either have a load capacity and speed rating at least equal to those of the original tyres, or conform to those recommended by an authorised dealer.
BODYWORK MAINTENANCE (1/3) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Your vehicle has been treated with very effective anti-corrosion products. It is nevertheless subject to various outside influences. Corrosive agents in the atmosphere – atmospheric pollution (built-up and industrial areas), – saline atmospheres (near the sea, particularly in hot weather), – seasonal and damp weather conditions (e.g.
BODYWORK MAINTENANCE (2/3) What you should not do Wash the vehicle in bright sunlight or freezing temperatures. Do not scrape off mud or dirt without pre-wetting. Allow dirt to accumulate on the exterior. Allow rust to form following minor impacts. Do not use solvents not approved by our Technical Department to remove stains as this could damage the paintwork. Do not drive in snow or muddy conditions without washing the vehicle, particularly under the wheel arches and body.
BODYWORK MAINTENANCE (3/3) Vehicles with a matte paint finish This type of paint requires certain precautions. Do not do the following Use wax-based products (polishing). Rub too hard. Wash the vehicle in a roller-type car wash. Wash the vehicle using a high-pressure device. Attach stickers to the paintwork (risk of leaving marks).
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit . . . . . . . . . . . . . . . . . . .
PUNCTURE/EMERGENCY SPARE WHEEL In the event of a puncture, there is either an emergency spare wheel or tyre inflation kit available, depending on the vehicle (refer to the information in the following pages). To access the emergency spare wheel 1 – Open the tailgate. – Undo the nut with the wheelbrace 1. – Detach the cage using handle 3. – Release the emergency spare wheel. 2 4 – Make sure the wheel is correctly positioned in the cage, valve facing down.
TYRE INFLATION KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE INFLATION KIT (2/3) With the engine running and the parking brake applied, – Disconnect any accessories previously connected to the vehicle’s accessories socket; If a minimum pressure of 1.8 bar is not reached after 15 minutes, repair is not possible; do not drive the vehicle but contact an approved dealer. – refer to the information on the inflation kit compressor and follow the instructions; 1 2 Depending on the vehicle, in the event of a puncture, please use the kit located in the glovebox.
TYRE INFLATION KIT (3/3) Once the tyre is correctly inflated, remove the kit: slowly unscrew the inflation end piece to prevent any product spatter and store the container in plastic packaging to prevent product leaks. Precautions when using the kit The kit should not be operated for more than 15 consecutive minutes.
TOOL KIT 9 8 1 Jack 9 Refer to Section 5 “Changing a wheel”. Retaining belt (depending on vehicle) After use, reposition it, making sure that it retains all components in the tool kit. 2 5 3 7 6 4 Remove tools or, depending on the vehicle, the tool kit. Hubcap tool 5 To remove the wheel trims. To remove the tool kit 1 from the luggage compartment Depending on the vehicle, it may be stored behind a flap. Open it. Undo wheel 2 and pull the tool kit towards you.
WHEELS, TRIM 2 A C 1 B D 3 Wheel trim 1 Wheel trim 3 Remove it using hubcap tool 2 (located under the tool kit), by pushing the hook into the opening located near the valve (to reach the metal retaining wire located behind the wheel trim). To remove it without removing the wheel, press it at the points indicated by the arrows. (concealed wheel bolts) To refit it, align it with the valve.
CHANGING A WHEEL (1/2) Continue tightening to position the baseplate on the ground correctly. Turn handle 3 on the jack to lift the wheel off the ground. 1 2 4 3 If necessary, remove the wheel trim. Use the wheelbrace 2 to slacken off the wheel bolts. Position it so as to be able to push from above. Switch on the hazard warning lights. Start extending jack 4 by hand, turning the handle. Keep the vehicle away from traffic and on a level surface where it will not slip.
CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. For vehicles fitted with alloy wheels, use the guide bolt located in the tool kit to finish loosening and start tightening the bolts. Fit the emergency spare wheel on the central hub and turn it to align the mounting holes in the wheel and the hub. Tighten the bolts and lower the jack. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel.
TYRES (1/3) The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. You must make sure that your tyres conform to local road traffic regulations. 2 1 When the tyre tread has been eroded to the level of the warning strips, they become visible 2: it is then necessary to replace your tyres because the tread profile is no more than 1.6 mm deep and this causes poor road holding on wet roads.
TYRES (2/3) Tyre pressures Respect the tyre pressures (including the emergency spare wheel). Check them at least once a month and before a long journey (refer to the label on the edge of the driver’s door). Please refer to the information on “Tyre pressures” in Section 4. Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey.
TYRES (3/3) Changing wheels around This practice is not recommended. Emergency spare wheel Refer to the information on the “Emergency spare wheel” and instructions on “Changing a wheel” in Section 5. Use in winter – Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains must not be fitted to tyres which are larger than those originally fitted to the vehicle.
HEADLIGHTS : changing bulbs (1/2) Front side light Open the cover 1. 1 Disconnect the bulb holder wiring 4. Remove bulb holder 4 from its housing. Replace the bulb. 3 Bulb type: W5W To refit it, carry out the above operations in reverse order. 2 4 Dipped beam/main beam headlights Open the cover 1. Disconnect the bulb holder wiring 2. Unclip spring 3 to remove the bulb holder 2. Bulb type: H4 It is essential to use 55W anti UV bulbs to prevent damage to the lights' plastic glass.
HEADLIGHTS : changing bulbs (2/2) 5 Direction indicator lights Turn the bulb holder 5 to release it and remove it from its location without disconnecting the wiring. Replace the bulb. Bulb type: PY21W To refit it, carry out the above operations in reverse order. To comply with local legislation, or as a precaution, you can obtain an emergency kit containing a set of spare bulbs and fuses from an approved Dealer. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
FOG LIGHTS: changing bulbs Additional lights If you wish to fit your car with fog lights or long range headlights, contact an authorised dealer. 1 2 Please note when working close to the engine that it may be hot. The engine cooling fan may also start Front fog lights 1 As it is necessary to remove parts or components (front bumper), you are advised to have your bulbs replaced by an approved dealer. Bulb type: H16 The bulbs are under pressure and can break when replaced. at any moment.
REAR LIGHTS: changing bulbs (1/3) 2 4 1 5 3 6 2 Rear lights Depending on the vehicle, open the hinged doors or the tailgate. Undo bolts 1 using a Torx tool. Unclip the lower section, then the upper section of the light by pulling it towards you. Pull tabs 2 to unclip bulb holders 3. Replace the bulb, then proceed in the reverse order to refit the bulb. Bulb type 4 Indicator Pear-shaped, bayonet type bulb P Y21W. 5 Side and brake light Pear-shaped, bayonet type bulb with two filaments P 21/5W.
REAR LIGHTS: changing bulbs (2/3) 7 High-level brake light – Version with tailgate: it is located above the rear screen, in the centre. – Version with hinged doors: it is located above the rear screen, on the left-hand door. 8 Remove the two plastic blanking covers 7 from the inside. Unclip the light using a screwdriver, by pressing in the metal clip housings. Remove light 8 from the outside. Replace the bulb without disconnecting the wiring.
REAR LIGHTS: changing bulbs (3/3) 9 10 Number plate light Release the light 10 to access bulbs. Undo two bolts 9 using a Torx tool. Bulb type: W5W. Replace the bulbs, then fit the light in position. 5.
INDICATOR LIGHTS: changing bulbs 2 1 Unclip indicator light 1 on the door side, using a flat-blade screwdriver type tool. Turn the bulb holder 2 a quarter of a turn and take out the bulb. Bulb type: WY5W. Replace the bulb and refit the indicator light. 5.
INTERIOR LIGHTING: changing bulbs 2 1 3 Passenger compartment lights Pull the bulb 2 to remove it from its housing. Remove the lens 1 using a tool such as a flat-blade screwdriver. Bulb type 2: W6W Rear courtesy light bulb type: W6W Replace the bulbs and replace the lens. Light 3 Remove the lens using a tool such as a flat-blade screwdriver. Pull the bulb to remove it from its housing. Bulb type 3 : W6W Replace the bulb and refit the lens. 5.
FUSES (1/2) To locate the fuses, please see the following page. It is not advisable to use the free fuse locations. 1 Some functions are protected by fuses located in the engine compartment. However, because of their reduced accessibility, it is recommended to have these fuses replaced by an authorised dealer. A Fuse box Tweezers 1 If any electrical component does not work, check the condition of the fuses. Remove the fuse using tweezers 1, located at the back of cover A. Unclip cover A.
FUSES (2/2) Number 1 2 27 28 3 4 5 6 7 8 9 10 29 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Allocation of fuses The presence of certain fuses depends on the vehicle equipment level. 5.
WINDSCREEN WIPER BLADES (1/2) 1 2 Check the condition of the wiper blades. You are responsible for their service life: Replacing windscreen wiper blades 2 – clean the blades, windscreen and rear screen regularly with soapy water; – With the ignition switched off, lift wiper arm 2 slightly; – do not use them when the windscreen or rear screen are dry; – pull tab 1 upwards; – free them from the windscreen or rear screen when they have not been used for a long time.
WINDSCREEN WIPER BLADES (2/2) 3 4 5 Replacing the rear screen wiper blade – With the ignition switched off, lift wiper arm 5; – pivot the blade 3; – press tab 4; – pull the blade to release it (arrow). For refitting, proceed in the reverse order and ensure that the blade is correctly clipped on. 5.24 – In frosty weather, make sure that the wiper blades are not stuck by ice (to avoid the risk of the motor overheating). – Check the condition of the wiper blades.
TOWING, BREAKDOWN (1/3) Choice of breakdown service In the event of an energy fault In the event of a fully discharged traction battery, any type of towing is permitted: towing on a flatbed truck or towing on the road using the tow eye (please see following pages). All other cases Only towing on a flatbed truck is permitted.
TOWING, BREAKDOWN (2/3) 4 2 1 In the event of an energy fault: towing In the event of a fully discharged traction battery: – the warning light Ṏ flashes; – needle 1 is in the lower section of the reserve zone. It is possible to recover on a flatbed truck or tow the vehicle using the tow eye, following the instructions below. When the engine is stopped, steering and braking assistance are not operational. 5.26 Before towing, insert the key in the switch to unlock the steering column.
TOWING, BREAKDOWN (3/3) 4 4 3 5 Access to towing points Unclip cover 3 or 5. Tighten the towing hitch 4 fully: first by hand until it stops then finish by locking it with the wheel brace. Only use the front and rear towing points (never use the driveshafts). These towing points may only be used for towing: never use them for lifting the vehicle directly or indirectly.
FITTED AUDIO EQUIPMENT 2 1 If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – radio 1; – bass speakers 2. To install any equipment, please consult an approved dealer. Radio location 1 Unclip the blanking cover. The aerial, + and – supply and speaker wire connections are located behind it. – In all cases, it is very important to follow the manufacturer’s instructions carefully.
ACCESSORIES (1/2) Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer.
ACCESSORIES (2/2) Using the diagnostic socket The use of electronic accessories on the diagnostic socket may cause serious disturbance to the vehicle’s electronic systems. For your safety we recommend that you use only electronic accessories approved by the manufacturer, consult an Approved Dealer. Serious accident risk. Use of transmission/receiving devices (telephones, CB equipment etc.).
RADIO FREQUENCY REMOTE CONTROL: batteries 1 2 Replacing the remote control battery Replace battery 2 according to the direction marked on the cover. Undo screw 1 to remove the remote control cover. Note: It is not advisable to touch the electronic circuit in the key cover when replacing the battery. The batteries are available from approved Dealers, and their service life approximately two years. Check that there is no dye on the battery: risk of an incorrect electrical contact.
OPERATING FAULTS (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons, you should always contact an approved Dealer as soon as possible. FAULTS POSSIBLE CAUSES WHAT TO DO Impossible to charge the traction battery. No electrical current in domestic sockets or poor connection of cable to domestic socket. Check your installation (circuit breaker, programmer, etc.). The exterior temperature is lower than -26°C.
OPERATING FAULTS (2/5) FAULTS POSSIBLE CAUSES WHAT TO DO The additional heating does not work. Fill up the fuel tank. Fill up with fuel – see information on the “Additional heating tank” in Section 1. The programmable heating does not work. One of the usage conditions is not complied with (the traction battery is not charged, etc.). See information on “Heating, air conditioning: programming” in Section 3. The vehicle clock is poorly adjusted or not adjusted.
OPERATING FAULTS (3/5) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved Dealer. Vibrations. Tyres not inflated to the correct pressure, incorrectly balanced or damaged. Check tyre pressures. If this is not the problem, have them checked by an authorised dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an authorised dealer as soon as possible. 5.
OPERATING FAULTS (4/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved Dealer. Fuse damaged. Replace the fuse (see information on “Fuses” in Section 5). The wiper does not stop. Faulty electrical controls. Consult an approved Dealer. Direction indicators flashing more quickly. Blown bulb. Replace the bulb. The direction indicators do not work.
OPERATING FAULTS (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The headlights do not switch on or off. Faulty electrical circuit or control. Consult an approved Dealer. Fuse damaged. Replace the fuse (see information on “Fuses” in Section 5). Traces of condensation in the headlights or rear lights. Traces of condensation may be a natural phenomenon caused by variations in temperature and humidity. In this case, the traces will disappear slowly once the lights are switched on. 5.
Section 6: Technical specifications Vehicle identification plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine identification plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dimensions . . . . . . . . . . . . . . . . . .
VEHICLE IDENTIFICATION PLATES A A 9 1 2 3 4 5 6 7 8 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. B 6.2 Vehicle identification plate A 1 Manufacturer name. 2 EC design number or approval number. 3 Identification number. Depending on the vehicle, this information is also given on marking B. 4 MAM (Maximum Authorised Mass). 5 GTW (Gross train weight: vehicle fully loaded, with trailer). 6 MPAW (Maximim Permissible Weight) for front axle.
ENGINE IDENTIFICATION PLATE/ENGINE SPECIFICATIONS C 1 2 3 C Engine identification plate Engine specification Quote the details given on engine plate C on all communication or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. Engine type 1: 5AM 6.
DIMENSIONS (in metres) (1/2) E A B F C D H G 6.
DIMENSIONS (in metres) (2/2) 2 seater 5 seater Medium A B 0,9 2.7 C D Long 3,1 0.7 4,3 4,7 E 2.1 F 1.5 G 1.5 H (unladen) 1.8 Turning circles between kerbs 10.7 11.9 Turning circles between walls 11.2 12.4 6.
WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Contact an approved Dealer.
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
SERVICE SHEETS (1/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (2/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (3/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (4/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (5/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
SERVICE SHEETS (6/6) VIN: .................................................................................. Date: Miles (Km): Type of operation: Service □ ....................................... □ Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Invoice number: Comments/miscellaneous Stamp Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Type of operation: Service □ .......................................
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
ALPHABETICAL INDEX (1/5) A ABS .......................................................................2.15 → 2.17 accessories............................................................. 5.29 – 5.30 accessories socket ............................................................ 3.18 additional heating fuel........................................................ 1.93 additional heating tank....................................................... 1.93 additional methods of restraint ...........................
ALPHABETICAL INDEX (2/5) driving recommendations ........................................... 2.6 – 2.7 E »ECO» mode function ......................................................... 2.8 ECO driving ................................................................ 2.6 – 2.7 ECO mode ........................................................................... 2.6 »400 volt» electrical circuit ........................................1.2 → 1.8 electric vehicle vehicle range ......................................
ALPHABETICAL INDEX (3/5) hubcap tool .......................................................................... 5.6 I indicators ......................................................... 1.83, 5.14, 5.19 indicators: direction indicators .............................................. 5.14, 5.19 instrument panel ..............................................1.66 → 1.71 instrument panel ....................................................1.66 → 1.80 instrument panel messages...................................
ALPHABETICAL INDEX (4/5) pedestrian warning system ................................................ 1.84 power-assisted steering..................................................... 1.61 practical advice ..........................................................2.6 → 2.9 presentation of the electric vehicle batteries ...............................................................1.2 → 1.7 pretensioners ..................................................................... 1.41 puncture.......................
ALPHABETICAL INDEX (5/5) transporting objects in the luggage compartment ............................. 3.25 – 3.26 trims ..................................................................................... 5.7 trip computer and warning system... 1.66 → 1.68, 1.74 → 1.80 tyre inflation kit...........................................................5.3 → 5.5 tyre pressure...................................................2.11 → 2.14, 4.8 tyre pressure loss warning.....................................2.11 → 2.
7.
RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
