LAGUNA DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. RENAULT engineers and technicians the research applied to Formula 1, have pooled their Benefiting skill to from create a quality lubricants are very high-tech products.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections Getting to know your vehicle ............................... 1 Driving ................................................................... 2 Your comfort . ........................................................ 3 Maintenance .......................................................... 4 Practical advice ..................................................... 5 Technical specifications . ..................................... 6 Alphabetical index .............
0.
Section 1: Getting to know your vehicle RENAULT cards: general information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic locking of opening elements when driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Headrests - Seats. . . . . . . . . . . . . . . . . . . . . . . . . . .
RENAULT cards: general information (1/2) The RENAULT card is used for: 2 3 1 4 5 1 2 3 4 5 Unlocking the doors and tailgate. Locking all doors and tailgate. Switching on the lighting remotely. Unlocking/locking the tailgate Integrated key. Special note The RENAULT “SERVICE” card, for vehicles equipped with it, can be identified by the word “SERVICE” engraved on the card. Refer to the information on the “RENAULT SERVICE card” in Section 1.
RENAULT cards: general information (2/2) Access to key 5 Press button 6 and pull on key 5 then release the button. 5 6 Using the key Refer to the information on “Locking/ unlocking the doors”. Once you have accessed the vehicle using the integrated key, replace it in its housing in the RENAULT card, then insert the RENAULT card into the card reader to start the vehicle.
Remote control RENAULT card: use Locking the doors and fuel filler flap 1 2 Press the locking button 2. 3 4 Unlocking the doors and fuel filler flap Press unlocking button 1. The hazard warning lights flash once to indicate that the doors have been unlocked. The hazard warning lights flash twice to indicate that the doors have locked.
“Hands-free” RENAULT card: use (1/3) 2 3 1 Use Unlocking the vehicle Note: Ensure that the RENAULT card is not in contact with other electronic equipment (computer, PDA, phone, etc.) as this could hinder its operation. Pressing button 3 or 4 (if fitted to the vehicle) also unlocks the entire vehicle. On equipped vehicles, in addition to the functions of the remote control RENAULT card, it can be used to lock and unlock without using the RENAULT card, when it is in access zone 1.
“Hands-free” RENAULT card: use (2/3) Locking using button 5 2 With the doors and tailgate closed, press button 5 on the driver’s door handle. The vehicle will lock. If a door or the tailgate is open or not closed properly, the vehicle will quickly lock/ unlock. 5 Note: the RENAULT card must be within the vehicle’s access zone (zone 1) to be able to use the button for locking. 1 Locking the vehicle There are three ways to lock the vehicle: remotely, using button 5, or using the RENAULT card.
“Hands-free” RENAULT card: use (3/3) 6 7 With the engine running, if, after having opened and closed a door, the card is no longer in the passenger compartment, the message “card not detected” (accompanied by a beep when the speed passes a certain level) warns you that the card is no longer in the vehicle. This prevents you driving away after having dropped off a passenger who has the card, for example. The warning disappears when the card is detected again.
RENAULT card: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. 1 2 If the vehicle is equipped with a deadlocking function, this allows you to lock the opening elements and to prevent the doors from being unlocked using the interior handles (for example, by breaking the window and then trying to open the door from the inside). 3 The hazard warning lights flash once to indicate that the doors have been unlocked.
RENAULT card “service” Deactivation of the “SERVICE” mode. 1 There are two possibilities: – Press a button on a RENAULT card (not the RENAULT SERVICE card); 2 – start the engine with a RENAULT card (not the RENAULT SERVICE card). With the card in reader 1, press button 3. 3 If the vehicle is equipped with this card, it can be identified by the word “SERVICE” engraved on the card. In certain situations, you may wish to entrust your vehicle to a third party (parking valet, mechanic, etc.
Opening and closing the doors (1/2) Card reminder buzzer 1 A beep will let you know if you have left the card in the reader when you open the driver’s door, and the “Remove card” message will appear on the instrument panel. 2 Door/tailgate open buzzer Opening the doors from the outside Opening from the inside With the doors unlocked or “hands-free” RENAULT card on you, hold handle 1 and pull it towards you. Note: the lights and accessories (radio etc.
Opening and closing the doors (2/2) 1 Child safety Ç Vehicle with switch 1 Press switch 1 to authorise opening of the rear doors. If the vehicle is equipped with electric rear windows, this action will also authorise their use. The indicator light in the switch lights up to confirm that the locks have been activated. Note: in the event of a system fault, the message “check child safety locks” is displayed on the instrument panel: consult an approved dealer.
Locking/unlocking the doors (1/2) Locking/unlocking the doors from the outside This is done using the RENAULT card; refer to the information on the “RENAULT card” in Section 1. In certain cases, the RENAULT card may not work: – if the RENAULT card battery is weak, flat, etc. – if equipment operating on the same frequency as the card (mobile phones, etc.) is used; – vehicle located in a high electromagnetic radiation zone.
Locking/unlocking the doors (2/2) 4 Locking the doors without the RENAULT card Doors and tailgate status indicator light For example, in the event of a discharged battery or the RENAULT card temporarily not working, etc. When the ignition is on, the indicator light integrated in switch 4 informs you of the status of the doors and tailgate: With the engine switched off and a door or tailgate open, press and hold switch 4 for more than five seconds.
Automatic locking when driving Activating/deactivating the function Refer to the information on the “Vehicle settings personalisation menu” in Section 1; “Automatic locking of the doors while driving” function: 1 = < : function activated Operating faults If you experience an operating fault (no automatic locking, the indicator light incorporated in button 1 does not light up when trying to lock the doors and tailgate, etc.), firstly check that the doors and tailgate are properly closed.
Front headrests To adjust the angle of the headrest 2 1 Depending on the vehicle, tilt section A towards or away from you to the required position. A 3 To remove the headrest Raise the headrest to its highest position (tilt the seatback backwards if necessary). Press button 1 and lift the headrest to release it. To refit the headrest To raise the headrest Pull the headrest upwards to the desired height. To lower the headrest Press button 2 and guide the headrest down to the desired height.
Front seats with manual control 5 4 1 2 3 To move the seat forwards or back Lift handle 1 to release. Release the handle at the desired position and make sure that it is locked. To tilt the seatback Turn control knob 4 to the required position. To adjust the lumbar support on the driver’s seat: Lower handle 5 to increase the support and lift to decrease it. To raise or lower the seat base Move lever 3 as many times as necessary upwards or downwards.
FRONT SEATS WITH ELECTRIC CONTROL Switch 3 is used for adjusting the seatback and switch 4 is used for adjusting the seat squab. On equipped vehicles, buttons 2 are used to store the chosen driving position (refer to the following page). 5 1 2 Adjusting the seat squab: – To move the seat forwards or back Move switch 4 forwards or backwards. – To raise or lower the rear of the seat base Move the rear of switch 4 upwards or downwards.
Driver’s seat with position memory Recalling a stored driving position It is possible to store three driving positions. A driving position includes the settings for the driver’s seat base and seatback and the door mirrors. With the vehicle stationary, briefly press button 1, 2 or 3 depending on the required stored driving position.
Seat belts (1/3) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belts to ensure optimum protection. Adjusting your driving position Make sure that the rear bench seat is securely locked in position so that the rear seat belts will operate efficiently.
Seat belts (2/3) ™ 1 3 5 4 5 Locking Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pulling on buckle 3). If the belt jams, allow it to return slightly before attempting to unwind it again. If your seat belt is completely jammed, pull slowly, but firmly so that just over 3 cm unwinds. Allow it to return slightly before attempting to unwind it again. If there is still a problem, contact an approved dealer.
SEAT BELTS (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. – For special operations (e.g.: fitting child seats) contact an approved Dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are composed of: – Have the entire restraint system checked following an accident. – seat belt inertia reel pretensioners; – lap belt pretensioners; – chest-level load limiters; – air bags for driver and front passenger. These systems are designed to act independently or together when the vehicle is subjected to a frontal impact.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Air bags for driver and front passenger Fitted to the driver and passenger side. Depending on the vehicle, the presence of this equipment is indicated by the word “air bag” on the steering wheel and dashboard (air bag zone A) and a symbol on the lower section of the windscreen.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operation This system is only operational when the ignition is switched on. In a severe frontal impact, the air bags inflate rapidly, cushioning the impact of the driver’s head and chest against the steering wheel and the front passenger against the dashboard. The air bags then deflate immediately so that the passengers are not in any way hindered from leaving the vehicle.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
Methods of restraint in addition to the rear seat belts Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (air bags, electronic control units, wiring) and the system components must not be reused on any other vehicle, even if identical.
Side protection devices Side air bags An air bag is fitted to each front seat and, depending on the country, the rear side seats; these air bags are deployed on the side of the seat (door side) to protect the occupants in the event of a severe side impact. Curtain air bags These are air bags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear side windows to protect the passengers in case of a severe side impact.
Additional methods of restraint All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. 1 The air bag is designed to complement the action of the seat belt. Both the air bags and seat belts are integral parts of the same protection system. It is therefore essential to wear seat belts at all times.
Child safety: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
Child safety: Choosing a child seat Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. Forward-facing child seats The child’s head and abdomen need to be protected as a priority.
child safety: choosing a child seat mounting (1/2) The are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected. Always check that the seat belt is correctly fastened by pulling it up, then pulling it out fully whilst pressing on the child seat.
child safety: choosing a child seat mounting (2/2) 1 3 2 The two rings 1 are located between the seatback and the seat base of the seat and are identified by a marking. To ensure your child seat can be easily fitted and locked on rings 1, use access guides 2 on the child seat. The third ring is used to attach the upper strap on some child seats. Fix the hook of the strap onto ring 3 and pull the strap so that the seatback of the child seat comes into contact with the seatback of the vehicle seat.
child safety: fitting a child seat (1/3) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seats indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
child safety: fitting a child seat (2/3) Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted. The anchorage points are located at the back of the rear bench seat. Child seat installation diagram ³ ² Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. seats.
child safety: fitting a child seat (3/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
child safety: deactivating/activating the front passenger air bag (1/3) 2 1 Deactivating the front passenger air bag To deactivate the air bag: when the vehicle is stationary, push and turn lock 1 to the OFF position. You must deactivate the front passenger air bag before fitting a child seat on the front passenger seat.
child safety: deactivating/activating the front passenger air bag (2/3) A 3 A The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered. 1.
child safety: deactivating/activating the front passenger air bag (3/3) DANGER 2 1 Activating the front passenger air bag Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEVER fit a rear-facing child seat on a front passenger seat with an active front air bag. The child may suffer very serious injuries if the air bag is triggered.
Driving position left-hand drive 1 2 3 4 5 6 7 22 21 26 25 24 23 8 9 10 15 14 16 17 20 18 19 1.
Driving position left-hand drive (continued) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 2 Side window demister outlet. 3 Stalk for: – direction indicator lights, – exterior lights, – front fog lights, – rear fog light. 4 Instrument panel. 5 Driver’s air bag and horn location. 6 – Steering column stalk for windscreen and rear screen wash/ wipe. – Trip computer information readout control and vehicle settings personalisation menu.
Driving position, right-hand drive 1 2 3 26 25 4 5 6 7 24 17 16 23 18 22 19 8 15 9 14 21 20 1.42 ENG_NU_936-3_BK91_Renault_1 ENG_UD3184_1 Poste de conduite direction à droite (X91 - B91 - K91 - Renault) driver’s position..................................... (up to the end of the DU) controls..................................................
Driving position, right-hand drive (continued) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side air vent. 2 Side window demister outlet. 3 Location for passenger air bag. 4 – Display (depending on the vehicle) for time, temperature, radio information, navigation system information, etc. – Driver and front passenger seat belt unfastened and passenger air bag deactivated warning lights 5 Heating and ventilation controls. 6 Centre air vents.
Steering wheel/power-assisted steering Variable power-assisted steering The variable power-assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. 1 Steering is made easier during parking manoeuvres (for added comfort) whilst the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds). Do not drive with a low battery charge. The steering wheel may not operate correctly.
Warning lights (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. A Instrument panel A: lights up when the ignition is switched on. In some cases, the appearance of a warning light is accompanied by a message. The warning light © means you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.
Warning lights (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ® A STOP light This lights up when the ignition is switched on and goes out as soon as the engine is started. It comes on with other warning lights and/or messages, and is accompanied by a beep. It requires you to stop immediately, for your own safety, as soon as traffic conditions allow. Switch off the engine and do not restart it. Contact an approved Dealer.
Warning lights (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ™ A Front seat belt reminder warning light This comes on when starting the engine then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approximately 12 mph (20 km/h), it flashes and a bleep sounds for around 120 seconds. Note: an object placed on the passenger seat base may activate the warning light in some cases.
Warning lights (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. ù Driving correction device warning light Refer to the information on “Driving correction devices” in Section 2. A Ä Toxic Fume Filter System Warning Light This lights up when the ignition is switched on and goes out when the engine is started.
Displays and indicators 1 2 1 3 2 Coolant temperature indicator 6 In normal use, the needle should be before area a. Under severe conditions, the needle may enter this area. This is not serious unless the ® warning light comes on, accompanied by a message on the instrument panel and a beep. 3 4 6 5 Trip computer and warning system a 5 6 Rev counter 1 (rpm × 1 000) Engine oil level low warning 2 When the engine is started, display 2 alerts the driver when the oil level is at its minimum.
TRIP COMPUTER: general information (1/2) c) mileage before service; d) tyre pressure monitor; 1 2 e) cruise control/speed limiter programmed speed; f) vehicle settings customisation menu; g) on-board log, operating fault and information message readout.
TRIP COMPUTER: general information (2/2) 2 3 Trip mileage resetting With “trip mileage recorder” selected on the display, press button 2 or 3 until the mileage recorder resets to zero. Resetting the journey parameters (reset button) With one of the journey parameters selected on the display, press button 2 or 3 until the display resets.
TRIP COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections 101778 KM 112. 4 KM Fuel used 8L Interpreting the display selected a) Total mileage and trip mileage recorder. b) Journey parameters. Fuel used. Fuel consumed since the last reset. Average Average fuel consumption since the last reset. 7.2 L/100 The value is displayed after having travelled at least 400 metres since the last reset. 1.
TRIP COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Current 9.4 L/100 Range 541 km Interpreting the display selected Current fuel consumption. This value is displayed above a speed of approximately 18 mph (30 km/h). Estimated range with remaining fuel. This range takes into account the average fuel consumption since the last time the reset button was pressed. The value is displayed after driving 400 metres.
TRIP COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Service in 1936 km/2 months Interpreting the display selected c) Mileage before service.
TRIP COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected d) Tyre pressure monitor Refer to the information on the “Tyre pressure monitor” in Section 2. Speed limiter 90 km/H e) Cruise control/speed limiter programmed speed. Refer to the information on the “Speed limiter” and “Cruise control” in Section 2. Cruise control 90 km/H 1.
TRIP COMPUTER: trip settings (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Settings menu: press and hold Interpreting the display selected e) Vehicle settings customisation menu. Enables certain vehicle functions to be set (instrument panel language, parking distance control, etc.). Refer to the information on “Vehicle settings customisation menu” in Section 1. f) Trip log.
TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected « Battery low start engine » Indicates that the vehicle must be started to recharge the battery (eg. after the engine has been switched off for some time whilst listening to the radio).
TRIP COMPUTER AND WARNING SYSTEM: operating fault messages These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The © warning light stays on. Examples of operating fault messages are given in the following pages.
TRIP COMPUTER AND WARNING SYSTEM: warning message These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.
Vehicle settings customisation menu Once a line has been selected, keep pressing either button 2 or 3 to change the function: For the “parking distance control volume” or “language” functions, you will have to make a further selection. In this case, make your selection and confirm it by holding either button 2 or 3, 1 2 ~ 3 This function, integrated into trip computer and warning system 1, allows certain vehicle functions to be activated/deactivated and adjusted.
Clock and exterior temperature 1 2 Vehicles equipped with a navigation system, radio, etc. External temperature indicator For vehicles which are not fitted with buttons 2 and 3, refer to the specific equipment instructions to discover the special features. Special note: When the outside temperature is –3°C to +3°C, the °C characters flash (signalling a risk of black ice on the road). 3 The time and, depending on the vehicle, the exterior temperature are displayed.
Rear-view mirrors (1/2) Storing the setting D 1 E For vehicles fitted with a driver’s seat with position memorisation, refer to the information on the “driver’s seat with position memory” in Section 1. Folding door mirrors A B C 3 2 Door mirrors The door mirrors automatically fold in when the vehicle is locked (switch 2 in position B). In this case, they will fold out when the ignition is next switched on.
Rear-view mirrors (2/2) Recalling the memorised position With the vehicle stationary and reverse gear engaged, select the door mirror using switch 3 and then briefly press the memory button chosen previously (refer to the information on the “Driver’s seat with position memory” in Section 1). 1 Returning to the driving position 3 – 10 seconds after reverse gear has been disengaged; – speed above 6 mph (10 km/h); – engine switched off; – switch 3 in the neutral position.
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. 1 0 A When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0. There is an intermediate position in which the stalk may be held when changing lanes. 2 When the stalk is released, it automatically returns to 0. Horn é Press on the top or sides of steering wheel boss A.
Exterior lighting and signals (1/3) 1 1 2 (only relates to front lights) Depending on the vehicle, the lights come on without using stalk 1 when the engine is started. To activate or deactivate this function, refer to the information on the “Vehicle settings personalisation menu” in Section 1. 3 á 4 u Side lights Turn the ring 2 until the symbol is opposite mark 3. The instrument panel will light up. The brightness can be adjusted by turning the control knob 4.
Exterior lighting and signals (2/3) 2 1 Special note: – If the dipped beam headlights are manually switched on and if the light is sufficient, the directional headlights will remain fixed; – If the lights come on automatically when cornering, the directional headlights will start working from the next time the vehicle corners; – When the dipped beam headlights are switched on with the engine running and the vehicle stationary, the lights move to reinitialise themselves.
Exterior lighting and signals (3/3) g 1 5 Front fog lights Turn centre ring 5 on stalk 1 until the symbol faces mark 6, then release it. Operation of the fog lights depends on the exterior lighting position selected, and an indicator light will light up on the instrument panel. 6 f Switching off the lights Turn ring 5 again until mark 6 is opposite the symbol for the fog light that you wish to switch off. The corresponding indicator light on the instrument panel goes out.
Electrical adjustment of the dipped beam headlights Examples of positions for adjusting control A according to the load Saloon and Estate Commercial vehicle Driver alone or with front passenger 0 0 Driver with one front passenger and one rear passenger 0 - Driver with one front passenger and two or three rear passengers 1 - Driver with one front passenger, three rear passengers and luggage 3 - Driver with luggage or (load) reaching the maximum permissible all-up weight 3 3 A On vehicles fi
FRONT WINDSCREEN WASH/WIPE (1/2) Vehicle fitted with front windscreen wiper rain sensor 1 E 1 A B C D 2 F A park B automatic wiper function. When this position is selected, the system detects water on the windscreen and triggers the wipers at a suitable wiping speed.
FRONT WINDSCREEN WASH/WIPE (2/2) Headlight washers 1 Headlights on On equipped vehicles, hold stalk 1 pulled towards you for about 1 second, and the headlight washers and windscreen washers will be activated at the same time. A B C D Note: when the minimum windscreen washer fluid level is reached, the headlight washer system may be deprimed. Windscreen washer Fill the windscreen washer fluid and then activate the windscreen washer, with the engine running, to reprime the system.
REAR screen wash/wipe 1 Activation/deactivation of the rear screen wiper Your vehicle is designed to activate the rear wiping function in reverse gear (if the windscreen wipers are operating). You can choose to activate or deactivate the function. To do this, refer to the information on the “Vehicle settings customisation menu” in Section 1; “Rear wiping in reverse gear”. A 2 Y Rear screen wiper With the ignition on, turn ring A of stalk 1 to align mark 2 opposite the symbol, then release it.
Fuel tank (1/3) Fuel grade Use a high-grade fuel that complies with the legislation in force in each country and which must conform to the specifications given on the label on cover A. Refer to the information on “Engine specifications” in Section 6. B A A Diesel versions It is essential to use diesel fuel that conforms with the information given on the label inside cover A. Petrol versions Capacity of the fuel tank: 66 litres approximately.
Fuel tank (2/3) Vehicles running on ethanol-based fuel It is essential to use unleaded petrol or fuel containing a maximum of 85% ethanol (E85). In very cold conditions, it may be very difficult or even impossible to start the engine.
Fuel tank (3/3) Persistent smell of fuel 2 If you notice a persistent smell of fuel you should: – stop the vehicle as soon as traffic conditions allow and switch off the ignition; – switch on the hazard warning lights and ask your passengers to leave the vehicle and to keep away from traffic; – contact an approved Dealer.
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting/Stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stop and Start Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN Petrol version Diesel version Up to 600 miles (1,000 km), do not exceed 78 mph (130 km/h) in top gear or 3,000 to 3,500 rpm. For the first 900 miles (1,500 km), do not exceed 2,500 rpm. After completing this mileage you may drive faster, however, it is only after approximately 3600 miles (6,000 km) that you may reasonably expect full performance. You may only expect top performance from your vehicle after approximately 1,800 miles (3 000 km).
Starting/stopping the engine (1/3) Starting a vehicle with an automatic gearbox Lever in position P. 1 For all vehicles: 2 3 Starting the engine Remote control RENAULT card When you get into the vehicle, insert the RENAULT card fully into card reader 2. To start, press button 1. If a gear is engaged, depress the clutch pedal to start the vehicle. RENAULT card in hands-free mode The RENAULT card must be inserted in card reader 2 or in detection zone 3.
Starting/stopping the engine (2/3) Operating faults In certain cases, the hands-free RENAULT card may not work: 1 – when the RENAULT card battery is drained, flat battery, etc. 2 – near to appliances operating on the same frequency as the card (monitor, mobile phone, video game, etc.); – vehicle located in a high electromagnetic radiation zone. The message “insert card” appears on the instrument panel. Insert the RENAULT card fully into card reader 2.
Starting/stopping the engine (3/3) Special note 1 2 If the card is no longer in the reader when you try to switch the engine off, the message “card absent- long press” appears on the instrument panel: press button 1 for longer than two seconds. When you leave your vehicle, especially if you have your RENAULT card with you, check that the engine is completely switched off. RENAULT card in hands-free mode With the card in the vehicle, press button 1: the engine will stop.
Stop and Start function (1/3) This system enables a reduced fuel consumption and lower greenhouse gas emissions. The system is activated automatically when the vehicle is started. While driving, the system stops the engine (standby) when the vehicle is at a standstill (traffic jam, traffic lights, etc). The message “Auto Stop” on the instrument panel indicates that the engine is on standby. The vehicle equipment remain operational while the engine is stopped.
Stop and Start function (2/3) Conditions preventing the standby of the engine Certain conditions prevent the system from using the engine standby function, including when: – reverse gear is engaged; – the bonnet is not locked; – the driver’s door is not closed; – the driver’s seatbelt is not fastened; – the outdoor temperature is too low or too high (less than around 0 °C or higher than around 30 °C); – the battery is not sufficiently charged; – the difference between the vehicle interior temperature
Stop and Start function (3/3) The system is automatically reactivated each time the vehicle is started using the start button (please see “Starting, stopping the engine)”. 1 Operating faults When the message “Check Stop & Start” appears on the instrument panel and the integrated warning light 2 lights up on the switch 1, the system is deactivated. Please consult an authorised dealer. 2 Deactivating, activating the function Press 1 to deactivate the function.
Special features of petrol versions The following operating conditions should be avoided: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
Special features of diesel versions Diesel engine speed Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected. If the message “Check antipollution” is displayed on the instrument Ä and panel accompanied by the © warning light; consult an approved dealer straight away.
Gear lever/Handbrake 1 The reversing lights will come on as soon as reverse gear is selected with the ignition on. Handbrake To release: Pull lever 3 up slightly, press button 2 and then lower the lever to the floor. 2 To apply: 3 Pull upwards, check that the vehicle is properly immobilised. 4 Make sure that the handbrake is properly released when driving (red indicator light off), otherwise overheating may occur.
ASSISTED PARKING BRAKE Note: 1 The message “apply parking brake” appears on the instrument panel and a beep sounds to indicate that the electronic parking brake is applied or released: This message may appear: 2 – with the engine running: when the driver’s door is opened; 3 – with the engine switched off (e.g. when the engine stalls): when a front door is opened. In this case, pull and release switch 3 to apply the electronic parking brake.
ASSISTED PARKING BRAKE (continued) Special cases When parking on a slope or towing a trailer, pull switch 3 for a few seconds to obtain the maximum braking effect.
ASSISTED PARKING BRAKE (continued) Versions with an automatic gearbox For safety reasons, automatic release is deactivated when the driver’s door is open or not shut properly and the engine is running (in order to prevent the vehicle from moving without the driver). The “release manually” message appears on the instrument panel when the driver depresses the accelerator. Never leave your vehicle without moving the selector lever to position P or N.
Advice: antipollution, fuel economy and driving (1/3) Your vehicle complies with criteria for recycling and recovering vehicles at the end of their service life which will come into force in 2015. Some parts of your vehicle have therefore been designed to facilitate future recycling. These parts are easy to remove so that they can be recovered and reprocessed by recycling companies.
Advice: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring system – Avoid sudden acceleration. – Brake as little as possible. If you anticipate an obstacle or bend in advance, you may then simply release the accelerator pedal. – Do not try to maintain the same speed up a hill, accelerate no more than you would on the level. Keep your foot in the same position on the accelerator pedal. – Double declutching and accelerating before switching off are unnecessary in modern vehicles.
Advice: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the Renault eco² signature. Emissions Manufacture Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
Tyre pressure monitor (1/3) If the vehicle is equipped with the function, this system monitors the tyre pressure. The tyre pressure can be adjusted when cold (refer to the information on “Tyre pressures”). If tyre pressures cannot be checked when the tyres are cold, the recommended pressures must be increased by 0.2 to 0.3 bar (3 PSI). 1 Operating principle Each wheel (except for the emergency spare wheel) has a sensor in the inflation valve which periodically measures the tyre pressure.
Tyre pressure monitor (2/3) “Check tyre pressure” 1 A shaded wheel B indicates a deflated tyre. A “Inflate tyres to motorway pressure” The tyre pressure is not suitable for the speed of travel. Slow down or inflate all four tyres to motorway pressure (refer to the information on “Tyre pressures”). “Puncture” B Display Display 1 on the instrument panel informs you of any tyre pressure faults (flat tyre, punctured tyre, system fault, etc.).
Tyre pressure monitor (3/3) Emergency spare wheel C D 3 Replacing wheels/tyres 3 F E 4 Interchangeability of wheels If you wish to swap the wheels around, please consult an approved dealer to reinitialise the system. If the vehicle is equipped with an emergency spare wheel, it will not have a sensor. When it is fitted to the vehicle, the message “tyre sensors absent” is displayed on the instrument panel.
Driver correction devices AND aids (1/5) Depending on the vehicle, they may comprise: – the ABS (anti-lock braking system); – the ESP (electronic stability program) with understeer control and traction control (ASR); – emergency brake assist with, depending on the vehicle, braking anticipation; – rear wheel steering. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions.
Driver correction devices AND aids (2/5) Electronic stability program (ESP) with understeer control and traction control (ASR) Electronic stability program ESP This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.). Operating principle A sensor in the steering wheel detects the direction selected by the driver. Other sensors throughout the vehicle measure the actual direction.
Driver correction devices AND aids (3/5) Traction control (ASR) offers additional safety; it is recommended that you do not drive with the function disabled. Correct this as soon as possible by pressing switch 1 again. Note: The function is reactivated automatically when the ignition is switched on or when a speed of approximately 24 mph (40 km/h) is exceeded. 1 Emergency brake assist This system supplements the ABS and helps reduce vehicle stopping distances.
Driver correction devices AND aids (4/5) A Operating faults – If the © indicator light together with the message “check steering” is displayed on the instrument panel: consult an approved Dealer. B – if the indicator light ® together with the message “steering fault” is displayed on the instrument panel, this indicates a fault in the system.
Driver correction devices/aids (5/5) Hill start assistance This function assists the driver when starting on hills. It prevents the vehicle from rolling backwards, depending on the slope, by automatically applying the brakes when the driver lifts his/her foot off the brake pedal to depress the accelerator pedal.
Cruise control/speed limiter: speed limiter function (1/3) 2 3 4 6 5 1 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. Controls Switching on 1 Main “On/Off” switch. 2 Limit speed activation, storage and increase switch (+). 3 Limit speed activation, storage and decrease switch ( - ). 4 Switch the function to standby, with limit speed stored (O). 5 Limit speed activation, storage and recall (R).
Cruise control/speed limiter: speed limiter function (2/3) Varying the limit speed To vary the limit speed, press switch 2 (+) repeatedly to increase the speed or switch 3 (-) to decrease it. 2 3 4 5 Exceeding the limit speed Limited speed cannot be maintained When driving down a steep gradient, the system is unable to maintain the limit speed: the stored speed will flash on the instrument panel information display to inform you of this situation.
Cruise control/speed limiter: speed limiter function (3/3) Recalling the limit speed If a speed has been stored, it can be recalled by pressing switch 5 (R). 2 3 4 5 1 Putting the function on standby Switching off the function The speed limiter function is deactivated if you press switch 1: in this case a speed is no longer stored. The orange instrument panel indicator light goes out to confirm that the function is deactivated. The speed limiter function is suspended when you press switch 4 (O).
Cruise control/speed limiter: cruise control function (1/4) 2 1 The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). This function is an additional driving aid. However, the function does not take the place of the driver.
Cruise control/speed limiter: cruise control function (2/4) 6 Press switch 1 on the side showing . Indicator light 6 comes on, lit green, and the message “cruise control” appears on the instrument panel, accompanied by dashes to indicate that the cruise control function is activated and waiting to store a cruising speed.
Cruise control/speed limiter: cruise control function (3/4) Exceeding the cruising speed 2 3 4 5 The cruising speed may be exceeded at any time by depressing the accelerator pedal. While it is being exceeded, the cruising speed flashes on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automatically return to its set cruising speed.
Cruise control/speed limiter: cruise control function (4/4) Returning to the cruising speed 2 3 4 5 If a speed is stored, it can be recalled, once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.). With a vehicle speed above 20 mph (30 km/h), press switch 5 (R). Note: if the speed previously stored is much higher than the current speed, the vehicle will accelerate more rapidly to reach this threshold.
PARKING DISTANCE CONTROL (1/3) Operating principle Ultrasonic detectors, installed in the front or rear bumper depending on the vehicle, measure the distance between the vehicle and an obstacle whilst reversing. 1 This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 25 centimetres from the obstacle.
PARKING DISTANCE CONTROL (2/3) A Front parking distance control (depending on vehicle) Operation The parking distance control system is only activated when the vehicle is driven at a speed below approximately 6 mph (10 km/h). Any object located less than approximately 60 centimetres from the front of the vehicle is detected. Display A shows the detection zones and a beep sounds.
PARKING DISTANCE CONTROL (3/3) Prolonged deactivation of the system You may permanently activate or deactivate the front or rear parking distance control separately.
Automatic gearbox (1/3) Driving in automatic mode 4 1 2 3 5 9 6 8 7 Selector lever 1 Operation Display 3 on the instrument panel shows the mode and gear selected. With gear lever 1 in position P, switch on the ignition. 4: P: park To move out of position P, you must depress the brake pedal before pressing unlocking button 2.
Automatic gearbox (2/3) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, move the lever to the left. Shifting the lever repeatedly allows you to change gears manually: – If the road contours and bends do not allow you to stay in automatic mode (e.g.: in the mountains), we recommend that you change to manual mode. This will prevent the automatic gearbox from changing gears repeatedly when climbing, and permit engine braking on long descents.
Automatic gearbox (3/3) Operating faults – When driving, if the message “Check gearbox” together with the warning light © appears on the instrument panel, this indicates a fault. Contact your approved Dealer as soon as possible. – When driving, if the message “Gearbox overheating” accompanied by warning light © appears on the instrument panel, stop the vehicle to allow the gearbox to cool down. Contact your approved Dealer as soon as possible.
2.
Section 3: Your comfort Air vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual air conditioning/heating system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air conditioning: information and advice on use . . . . .
AIR VENTS, air outlets (1/2) 1 3 2 4 5 6 7 8 9 10 8 1 left-hand side window demister outlet 2 left-hand side air vent 3 windscreen demister outlets 6 right-hand side window demister outlet 4 dashboard upper air vent 7 right-hand side air vent 5 air conditioning control panel 8 passenger footwell heater outlets 9 centre air vents 10 rear passenger air vents 3.2 ENG_NU_936-3_BK91_Renault_3 ENG_UD22211_6 Aérateurs (sorties d’air) (X91 - B91 - K91 - Renault) Air vents air vents.....
AIR VENTS, air outlets (2/2) 1 2 2 1 3 2 Air flow Direction Move the control knob 1 (beyond the point of resistance). Right/left: move tabs 2 to the right or left. Up: maximum air flow. Up/down: lower or raise tabs 2. To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. Down: closed. Move control knob 3 (beyond the point of resistance). To the right: maximum air flow. To the left: closed.
Manual air conditioning/heating system Switching air conditioning on or off 3 2 1 The air conditioning is switched on (indicator light illuminated) or off (indicator light extinguished) using button 1. a 4 5 8 7 6 The controls 1 Air conditioning. 2 Air temperature. 3 Display. 4 Ventilation speed. 5 Distribution of air in the passenger compartment. 6 De-icing/demisting of the rear screen and, depending on the vehicle, the door mirrors.
Manual air conditioning/heating system (continued) Position 0 (ventilation fan in zone b empty) b 4 1 8 the system is deactivated: the ventilation speed for the passenger compartment air is zero (vehicle stationary), you can however still feel a slight flow of air when the vehicle is moving. Clear View function Press button 7: the integrated indicator light comes on.
automatic climate control (1/4) 2 3 4 12 1 11 5 6 10 9 8 7 The controls 1 and 5 Air temperature. 2, 3 and 4 Automatic programmes. 6 Distribution of air in the passenger compartment. 7 De-icing/demisting of the rear screen and, depending on the vehicle, the door mirrors. 8 “Clear View” function.
automatic climate control (2/4) Switching air conditioning on or off 3 In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions. 12 Press button 10 to switch off the air conditioning. 10 11 Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level.
automatic climate control (3/4) 2 12 „ the air flow is directed towards the dashboard air vents (position which allows the passenger compartment to be heated or cooled as quickly as possible). 4 3 a 11 6 8 7 Adjusting the distribution of air in the passenger compartment There are seven air distribution options. Press switch 6 to scroll through them.
automatic climate control (4/4) Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle; – air recirculation allows the external atmosphere to be cut off (when driving in polluted areas, etc.). Manual use Pressing button 9 allows air recirculation to be activated, in this case, the integrated indicator comes on; 9 Air recirculation This function is controlled automatically, but it can also be activated manually.
Air conditioning: information and advice on use Advice on use In some situations, (air conditioning off, air recirculation activated, ventilation speed at zero or low, etc.) you may notice that condensation starts to form on the windows and windscreen. If there is condensation, use the “Clear View” function to remove it, then use the air conditioning in automatic mode to stop it forming again. If the condensation does not clear, use the FAST programme.
Electric windows, electric sunroof (1/3) These systems operate with the ignition on or off, until the driver’s door is opened (limited to about 5 minutes). Safety of rear occupants Depending on the vehicle, the driver can disable operation of the electric windows and the rear doors by pressing switch 4. The indicator light integrated in the switch lights up to confirm that the locks have been activated.
Electric windows, electric sunroof (2/3) Special note 7 0 A B 9 Sunroof blind Sunroof Only ever operate the blind with the sunroof closed: – Open the blind – to open: push handle 7 upwards and guide the blind as it retracts; – to close: pull handle 7 until it clicks into the catch. C D Your vehicle is equipped with an antipinch facility: when the sunroof encounters resistance whilst closing, (somebody’s fingers, etc.) it stops and then moves back several centimetres.
Electric windows, electric sunroof (3/3) Remote control window closing (for vehicles with one-touch windows on all windows). When you lock the doors from the outside, press the locking button on the RENAULT card twice in quick succession, or on the driver's door in hands-free mode, and all the windows will close automatically. It is recommended that the user only operates the system when the vehicle can be seen clearly and no one is inside.
SUN VISOR 5 1 3 2 4 6 6 4 Front sun visor Side sun blind Rear sun blind Lower the sun visor 1 over the windscreen or unclip it and turn it over the side window. Pull the sun visor upwards using tab 3 until hooks 4 engage in their housing (make sure the hooks are properly locked in position). Pull the sun visor upwards using tab 5 until hooks 6 engage in their housing (make sure the hooks are properly locked in position).
Interior lighting (1/2) 1 2 3 5 4 Courtesy light Front door lights Glove box light 5 Tilt switch 2 to move it to the position for: Light 4 comes on when the door is opened. Light 5 comes on when the cover is opened. – permanent lighting; – intermittent lighting, which comes on when a door is opened. This switches off after a time delay, once the doors concerned have been closed correctly; – immediate switching off. Map reading lights (depending on vehicle) Press switches 1 or 3.
Interior lighting(2/2) 8 7 6 Floor lights 6 Floor light 6 comes on when a door is opened. Luggage compartment lights 7 or 8 Depending on the vehicle, light 7 or 8 comes on when the luggage compartment is opened. 3.
Passenger compartment storage space and fittings (1/4) 2 1 Door pockets 1 Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning or braking. Dashboard storage compartment 2 Nothing should be placed on the floor area in front of the driver as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. 3.
Passenger compartment storage space and fittings (2/4) 4 5 3 6 A Sun visor storage 3 This can be used for storing motorway tickets, cards, etc. Front centre armrest storage compartment A Glove box Press button 4 and lift cover 5. The glove box can hold A4-sized documents, a large bottle of water, etc. Pull handle 6 to open it. It is ventilated and refrigerated. 3.18 ENG_NU_936-3_BK91_Renault_3 ENG_UD20458_1 Rangements, aménagements habitacle (X91 - B91 - K91 - Renault) armrest: front..........
Passenger compartment storage space and fittings (3/4) 9 7 10 8 11 Cup holder 7 Door pockets 8 This can be used to hold a can or a cup. Rear armrest storage Lower armrest 11 and lift cover 10 using unlocking handle 9. Press the top to deploy or store it. When turning corners, accelerating or braking, ensure that the receptacle being held by the cup holder is not dislodged. There is a risk of burning if hot liquid escapes.
Passenger compartment storage space and fittings (4/4) 12 14 15 13 Clothes hooks 12 Grab handle 13 Front seat storage compartments 14 Storage net 15 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. 3.20 ENG_NU_936-3_BK91_Renault_3 ENG_UD20458_1 Rangements, aménagements habitacle (X91 - B91 - K91 - Renault) armrest: rear...................................................................
Ashtray/cigar lighter/accessories socket 1 2 4 3 Ashtray 4 or 7 Press on cover 1 or pull cover 7 to open it. To empty it, pull divider 3, lifting the rear of the ashtray, or pressing tab 6. 6 7 5 5 Cigar lighter 2 With the ignition on, push in the cigar lighter; it will spring back with a click when it is ready. Pull it out to use. After use, replace it without pushing it all the way in. Accessories sockets You may use the cigar lighter recess 2 or one of sockets 5 (depending on the vehicle).
Rear headrests 1 2 A 2 Position for use To refit the headrest Raise or lower the headrest while pulling it towards the front of the vehicle. Insert the headrest rods into the sleeves, and lower the headrest to the first notch. To remove the headrest Press tab 1 and 2 simultaneously remove the headrest. Note: on the saloon version, first lower the bench seatback (refer to the information on the “Rear seat functions” in Section 3).
REAR BENCH SEAT 3 1 2 A The seatbacks can be folded down in order to transport large objects. In all situations, lower the rear headrests (refer to the information on the “Rear headrests” in Section 3). Saloon version Sport tourer versions Press button 2 or pull handle 3: the seatback will fold down by itself. Note: when you are folding a seatback back up, check that it is correctly locked (button 2 is flush). Press button 1 and lower seatback A.
Tailgate 1 3 A 4 2 Saloon version To open Press button 1 and lift the tailgate. To close Lower the tailgate using the handles 3 inside the tailgate to help you. Sport tourer versions Opening manually from inside the vehicle To close Lower the tailgate using the handles 3 inside the tailgate to help you. Special note: To open Press button 2 and lift the tailgate. If it is impossible to unlock the tailgate, it can be done from inside.
OPENING REAR SCREEN 1 2 2 Vehicle with opening rear screen To close The rear screen is locked and unlocked at the same time as the doors. Hold the base of screen wiper 1 and fold back the rear screen until it locks in position. To open Use restriction Press button 2. Lift the rear screen by the base of screen wiper 1. It is not possible to open the tailgate and the opening rear screen at the same time (electronically inhibited).
REAR PARCEL SHELF 1 2 Removal Unhook the two cords 1 (tailgate side). Lift rear parcel shelf 2 slightly and pull it towards you. To refit it, proceed in reverse order to removal. Do not place any objects, especially heavy or hard objects, on the parcel shelf. These may pose a risk to the vehicle occupants if the driver has to brake suddenly or if the vehicle is involved in an accident. 3.26 ENG_NU_936-3_BK91_Renault_3 Rear parcel shelf rear parcel shelf.....................................
LUGGAGE COMPARTMENT COVER 1 3 A B 2 3 3 2 2 C To remove the flexible section 1 of the luggage cover 2 Press on the rear of the luggage compartment cover (movement A): the luggage compartment cover rolls out automatically. Removing the luggage cover 2 Slide button 3 and lift the right-hand side (movement B) of the roller at the same time. D Luggage compartment cover storage 2 Lift up the rear of luggage compartment carpet 3; Then lift the left-hand side of the roller and remove it.
Luggage compartment storage space and fittings (1/2) A 2 1 Saloon version Side storage compartments Storage under carpet 2 Fold back section A to open it. Located on each side of the luggage compartment, storage compartments 1 may be used to store oil containers, etc. 3.28 ENG_NU_936-3_BK91_Renault_3 ENG_UD23649_2 Rangements, aménagements coffre à bagages (X91 - B91 - K91 - Renault) Luggage compartment storage space and fittings storage compartments...........................
Luggage compartment storage space and fittings (2/2) B 3 4 6 5 6 Sport tourer versions Separating the luggage compartment The loading area can be separated. Lift divider 3. On the back there is an elastic strip 4 to hold small objects vertically in position. Maximum weight: 30 kg. B D 7 C Hook for holding bags whilst cornering Prevents bags moving when the vehicle goes around a corner. Press on hook 5, it will deploy. To store it, lift it and press the top again. Maximum weight: 20 kg.
Transporting objects in the luggage compartment/Towing (towing equipment) C = 1000 mm Permissible nose weight, maximum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. A C In all cases, take care to comply with local laws (e.g. remove the towing ball when not towing).
Luggage net (1/3) Refitting the luggage net A 2 1 B With the rear bench seatbacks 1 completely folded down, find the roller. From the right-hand rear door, slide roller 2 on the rails 3 located on the back of the large section of the rear bench seatback: ensure it is correctly locked by moving it back and forth gently, then lock the rear bench seatbacks back into place. 3 Depending on the vehicle, this may be used when transporting animals or luggage to isolate them from the passenger section.
Luggage net (2/3) 6 6 5 5 4 5 5 7 Positioning the luggage net 7 Behind the rear seats Remove rod 5 from its housing and insert it into the anchorage points 6 (it must be inserted in ring 7). From the rear seats, lift covers 4 to access the anchorage points used as upper attachments for the net. Fold up the seatbacks and lock them. Check that they are correctly locked by moving them back and forth gently.
Luggage net (3/3) 8 9 5 5 NB: when the luggage net roller is installed on the back of the large section of the seatback, a system ensures the seatback does not fold down unintentionally. It is therefore necessary, after unlocking the seatback, to tilt it by pulling from the top beyond the point of resistance, from the right-hand rear door side.
multimedia equipment Navigation system The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle navigation system version. 1 Radio; 2 Central control; 3 CD or DVD reader; 4 Microphone; 5 Steering column controls. 1 3 2 Hands-free telephone integrated control On equipped vehicles, use microphone 4 and steering column control 5.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . topping up/filling. . . . . . . . . . . . . . . . .
Bonnet (1/2) A 2 1 To open, pull handle 1, located on the left-hand side of the dashboard. Unlocking the bonnet catch To unlock, lift tab 2 (hook A will release the bonnet). The engine may be hot when carrying out operations in close proximity. In addition, the engine cooling fan can come on at any moment. Risk of injury. Opening the bonnet Lift the bonnet and release stay 4 from its holder 5. For your own safety, it is very important to fix the stay into retainer 3 in the bonnet.
Bonnet (2/2) 3 4 5 Deactivate the Stop and Start function for any operation performed in the engine compartment. Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet, replace stay 4 back into its holder 5, hold the bonnet in the middle and lower it to 30 cm above the closed position, then release it. It will latch automatically under its own weight.
ENGINE OIL LEVEL: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. Oil change frequency: check the oil level from time to time and certainly before any long journey to avoid the risk of damaging your engine.
ENGINE OIL LEVEL: general information (2/2) Once the operation has been completed, ensure that the dipstick is pushed in as far as it will go or that the cap-type dipstick is completely screwed in. B A C Exceeding the maximum engine oil level The oil level should only be read with the dipstick as explained above. B If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer.
ENGINE OIL LEVEL: topping up/filling (1/2) 1 1 1 2 2 2 Topping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). – Unscrew cap 1; – top up the level (as a guide, the capacity between the minimum and maximum reading on the dipstick 2 is between 1.
Engine oil level: topping up/filling (2/2)ENGINE OIL CHANGE Oil change 2 1 1 2 Service interval: refer to the Maintenance Service Booklet for your vehicle. Average capacities for oil change including oil filter (for information) 2.0 16V engine : 4.4 litres 2.0T engine: 5.4 litres 1.5 dCi engine : 4.5 litres 2.0 dCi engine : 7.4 litres Engine oil grade Refer to the Maintenance Service Booklet for your vehicle.
LEVELS (1/3) 1 B A Checking intervals Replacement intervals Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). Refer to the Maintenance Service Booklet for your vehicle. If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – anticorrosion protection of the cooling system.
LEVELS (2/3) 1 Level 1 Topping up The level normally goes down at the same time as the brake lining wear, but it must never go below the « MINI » warning level. After any operation on the hydraulic circuit, a specialist must replace the fluid. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s website. Only use fluids approved by our Technical Department (and taken from a sealed container).
FILTER (3/3)/LEVELS Liquid Screen wash product (product with antifreeze in winter). 1 Jets Use a tool such as a needle to adjust the height of the windscreen washer jets. Filters The replacement of filter elements (air filter, cabin filter, diesel fuel filter, etc.) is scheduled in the maintenance operations for your vehicle. Replacement intervals for filter elements: refer to the Maintenance Service Booklet for your vehicle.
Tyre pressure A A C E C E B B H The tyre pressure is indicated on label A affixed to the edge of the driver’s door. Open the door to read it. Zone B: dimension of the tyres fitted to the vehicle. Zone C: tyre pressures for the front wheels (non-motorway). D F D F G Zone D: tyre pressures for the rear wheels (non-motorway). Zone E: tyre pressures for the front wheels (motorway). Zone F: tyre pressures for the rear wheels (motorway). Zone G: tyre pressure for the emergency spare wheel.
Battery Depending on the vehicle, the battery is in the engine compartment or in the luggage compartment. It is always maintenance-free. Replacing the battery A As this operation is complex, we advise you to contact an approved Dealer. Depending on the vehicle, a system continuously checks the battery charge status. If the level drops, the message “Low battery, start engine” is displayed on the instrument panel. In this case, start the engine.
Bodywork maintenance (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Protection against the effects of corrosive agents Although your vehicle has been treated with very effective anti-corrosion products, it nevertheless remains subject to the effects of different parameters.
Bodywork maintenance (2/2) You should Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. Remember to visit the body shop periodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Service Booklet. Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway).
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the interior of the vehicle regularly. A stain should always be dealt with swiftly. Whatever type of stain is on the trim, use cold (or warm) soapy water with natural soap. Detergents (washing-up liquid, powdered products, alcohol-based products) should not be used. Use a soft cloth. Rinse and soak up the excess. Glass instrument panel (e.g.
INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable equipment originally fitted in the vehicle If you need to remove equipment in order to clean the passenger compartment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driver’s mat should be fitted on the driver’s side, etc.) and fit them with the components supplied with the equipment (for example, the driver mat should always be fixed using the pre-fitted mounting components).
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emergency spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit (jack, wheelbrace, etc.). . .
Puncture/EMERGENCY SPARE WHEEL In the event of a puncture, depending on the vehicle, you will have: 1 An emergency spare wheel or tyre inflation kit (refer to the information on the following pages). 1 2 Emergency spare wheel Special note: The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emergency spare wheel disappears from the instrument panel display). Refer to the information on the “Tyre pressure monitor” in Section 2.
TYRE INFLATION KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE INFLATION KIT (2/3) 2 3 4 5 6 1 7 10 9 8 Depending on the vehicle, in the event of a puncture, use the tyre inflation kit. Before using this kit, park the vehicle at a sufficient distance from traffic, switch on the hazard warning lights, apply the handbrake, ask all passengers to leave the vehicle and keep them away from traffic.
TYRE INFLATION KIT (3/3) 1 10 8 Once the tyre is inflated correctly: – stop using the kit; – slowly unscrew the two inflation end pieces 8 and 10; – screw end piece 10 onto the bottle so that no product escapes; Nothing should be placed around the driver’s feet as such objects may slide under the pedals during sudden braking manoeuvres and obstruct their use.
TOOL KIT/wheel trim The tools included in the tool kit depend on the vehicle. 1 A 4 Jack 1 Fold it and position retainer A correctly before refitting it in its housing. F Towing hitch 2 Refer to the information on “Towing” in Section 5. B D 2 The tool kit is located in the luggage compartment: lift the luggage compartment carpet, remove the jack then unscrew the central mounting. When refitting, always clip the jack with flange B facing downwards.
Changing a wheel (1/2) Vehicles equipped with a jack and wheelbrace 3 1 2 4 Switch on the hazard warning lights. Keep the vehicle away from traffic and on a level surface where it will not slip (if necessary, place a solid support under the jack base). Apply the parking brake and engage a gear (first or reverse, or P for automatic transmissions). Ask all the passengers to leave the vehicle and keep them away from traffic. If necessary, remove the wheel trim.
Changing a wheel (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel. Tighten the bolts, checking that the wheel is correctly positioned on its hub and unscrew the jack. With the wheel on the ground, tighten the bolts fully and check they are tight as quickly as possible: tightening torque 130 N.
Tyres Tyre and wheel safety The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. When the tyre tread has been eroded to the level of the warning strips, they become visible 2: it is then necessary to replace your tyres because the tread profile is no more than 1.6 mm deep and this causes poor road holding on wet roads. 2 You must make sure that your tyres conform to local road traffic regulations.
Tyres (continued) Tyre pressures Adhere to the tyre pressures (including the emergency spare wheel). The tyre pressures should be checked at least once a month and additionally before any long journey (refer to the label affixed to the edge of the driver’s door). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey.
Tyres (continued) Changing wheels around Use in winter This practice is not recommended. Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains cannot be fitted to tyres which are larger than those originally fitted to the vehicle. In all cases, we would recommend that you contact an approved dealer who will be able to advise you on the choice of equipment which is most suitable for your vehicle.
Halogen headlights: changing bulbs Front side light Remove cover A, then pull bulb holder 6 to access the bulb. 2 A 3 B 1 However, because the protective covers need to be removed, you are advised to have your bulbs replaced by an approved dealer. 6 4 5 Direction indicator lights Consult an approved dealer. Dipped beam/main beam headlights Remove cover A or B then unclip bulb 2 by pressing on connector 1, and remove the assembly from its housing or remove spring 5 then connector 4 from bulb 3.
XENON HEADLIGHTS: changing bulbs 1 A B Because some components (the battery, its mounting) need to be removed, you are advised to have your bulbs replaced by an approved dealer. Dipped beam headlights with discharge bulbs B Bulb type: D1S. dealer. Due to the danger involved in handling high-voltage devices, this type of bulb must be replaced by an approved 2 Daytime running light Remove cover A, then turn bulb holder 1 to the left. Bulb type: W21/5W.
HEADLIGHTS: additional/front fog lights Additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved dealer. 1 Front fog lights 1 However, because the front bumper needs to be removed, you are advised to have your bulbs replaced by an approved dealer. The bulbs are under pressure and can break when replaced.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (1/5) 1 2 Saloon version 3 Undo bulb holder 3 a quarter of a turn. 4 Replace bulb 4. Bulb type: W16W. Direction indicator lights From the luggage compartment, undo 2 a quarter of a turn to access bolt 1. Undo it then pull the light unit outwards. The bulbs are under pressure and can break when replaced. To comply with current legislation, or as a precaution, you can obtain an emergency kit from an approved dealer containing a set of spare bulbs and fuses.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (2/5) 8 7 5 6 Saloon version (continued) Undo bolt 6 in order to remove light unit 7 by pushing it outwards. Reversing light Undo bulb holder 8 a quarter of a turn then replace the bulb. From the luggage compartment, unclip flap 5. Bulb type: W16W. Rear fog light Undo bulb holder 9, turning it towards the centre of the vehicle by accessing it from underneath. The bulbs are under pressure and can break when replaced. Bulb type: P21W.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (3/5) 11 12 13 A A Sport tourer versions From the luggage compartment, remove the side carpet. Note: depending on the vehicle, it may be necessary to remove the door of storage compartment A. From inside, undo the three bolts 10 then, from the outside, detach the light unit by pulling it back, and unclip the bulb holder. Replace the bulb concerned. 14 11 Side lights/stop lights Bulb type: P21/5W. 12 Direction indicator light Bulb type: PY21W.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (4/5) 16 B 18 15 17 Accessibility for vehicles equipped with a speaker on the left of the luggage compartment From the luggage compartment, remove the side carpet. Undo the three screws 15, 16 and 17 and remove the speaker. Note: on 5-door versions, hold the housing with both hands and pull the top part of the housing towards you while holding mounting 16 up against the trim.
REAR LIGHTS AND SIDE LIGHTS: changing bulbs (5/5) 20 22 19 C 21 Saloon and sport tourer versions Number plate lights 20 Side indicator lights 22 Unclip light 20 by pressing tab 21. Unclip indicator light 22 (using a flatblade screwdriver type tool positioned at C to move the indicator light towards the front of the vehicle). High level brake light 19 Remove the light cover to gain access to the bulb. Consult an approved Dealer. Bulb type: C5W festoon type bulb.
INTERIOR LIGHTS: changing bulbs (1/2) 1 A B 2 3 Courtesy light Door lights Front floor lights Insert a flat-blade screwdriver type tool to unclip the light cover on side A then side B. Unclip light 2 (using a flat-blade screwdriver or similar). These are located behind the dashboard and on the lower section. Remove the bulb concerned 1. Turn the bulb holder a quarter of a turn and take out the bulb. Turn bulb holder 3 a quarter of a turn and take out the bulb. Bulb type: W5W. Bulb type: W5W.
INTERIOR LIGHTS: changing bulbs (2/2) 4 6 5 7 Luggage compartment lights Unclip the light at 4 using a flat-blade screwdriver or similar. Disconnect the light. Press tab 5 to release lens 7 and access bulb 6. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
FUSES (1/2) 1 3 2 A Fuse box 2 Clip 3 If any electrical component does not work, check the condition of the fuses. Remove the fuse using tweezers 3, located at the back of storage compartment A. Open storage compartment A. Press tab 1 to move it then pull it towards you to unclip it. To identify the fuses, refer to the fuse allocation label (shown on the following page). Check the fuse in question and replace it, if necessary, by a fuse of the same rating.
FUSES (2/2) Allocation of fuses (DEPENDING ON THE EQUIPMENT LEVEL) Symbol Z Allocation Symbol Allocation Interior lighting Radio amplifier Interior rear-view mirror î Radio C Heated rear screen a Instrument panel Ì Horn n Driving correction devices Child safety Electric seats Indicator ë Accessories sockets Electric windows y Ventilation ñ Heated seats t Air conditioning E Rear screen wiper Æ Cigar lighter D [ Sunroof Electronic parking brake Ý Towin
Battery: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger Do not place metal objects on the battery as this could create a short circuit between the terminals. The battery charger must be compatible with a battery with nominal voltage of 12 volts. Battery Follow the instructions given by the manufacturer of the battery charger you are using. Never disconnect it.
Battery: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle (continued) Ensure that there is no risk of contact between the two vehicles (risk of short circuiting when the positive terminals are connected) and that the discharged battery is properly connected. Switch off your vehicle ignition. Start the engine of the vehicle supplying the current and run it at an intermediate engine speed. Leads A and B must only be connected to the terminals indicated.
RENAULT card: battery 2 A B 1 4 3 Replacing the battery When the message “Low card battery” appears on the instrument panel, replace the RENAULTcard battery, press button 1, pulling on emergency key 2, then unclip cover 3 using tab 4. Remove the battery by pressing on one side (movement A) and by lifting the other (movement B) then replace it, ensuring the polarity and model, shown on cover 3 are respected.
Fitting a radio 2 1 3 If your vehicle is not fitted with a radio, one can be fitted and locations have been provided for: – the radio 1; – tweeter speakers 2; – bass speakers 3. To install any equipment, please consult an approved dealer. Radio location 1 Unclip the blanking cover. The aerial, + and – supply and speaker wire connections are located behind it. – In all cases, it is very important to follow the manufacturer’s instructions carefully.
ACCESSORIES Before fitting an electrical or electronic device (particularly for transmitters/receivers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle. If you are using an anti-theft device, only attach it to the brake pedal. Contact an approved dealer for this information. Electrical and electronic accessories – Connect accessories with a maximum power of 120 Watts only. Fire hazard.
WINDSCREEN WIPER BLADES 1 B A 4 2 C 5 3 Replacing windscreen wiper blades 1 With the ignition on and engine switched off, lower the windscreen wiper stalk completely: they stop slightly away from the bonnet. Lift wiper arm 3, pull tab 2 (movement A) and push the blade upwards. To refit Slide the blade along the arm until it clips on. Make sure that the blade is correctly locked in position. Return the windscreen wiper stalk to the park position. 6 Check the condition of the wiper blades.
Towing: breakdown Before towing, unlock the steering column: with the clutch depressed, engage first gear (lever in position N or R for vehicles with automatic transmissions), insert the RENAULT card in the card reader then press the engine start button for two seconds. The column is unlocked, the accessory functions are supplied: the vehicle lights can be used (indicators, brake lights etc.). At night the vehicle must have its lights on.
Towing: breakdown (continued) – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. 2 – A vehicle must not be towed if it is not fit to be driven. 5 3 4 – Avoid accelerating or braking suddenly when towing, as this may result in damage being caused to the vehicle. 4 6 Only use the front 3 and rear 5 towing points (never use the driveshafts or any other part of the vehicle).
Operating faults (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or unlock the doors. Card battery is flat. Replace the battery. You can still lock/ unlock and start your vehicle (refer to the information on “Locking/unlocking the doors” in Section 1 and “Starting/Stopping the engine” in Section 2).
Operating faults (2/5) The starter is activated POSSIBLE CAUSES WHAT TO DO The instrument panel indicator lights are weak or fail to light up and the starter does not turn. Battery terminals not tight, battery terminals disconnected or oxidised. Retighten or reconnect the terminals, or clean them if they are oxidised. Discharged battery or not operational. Connect another battery to the faulty battery.
Operating faults (3/5) On the road POSSIBLE CAUSES WHAT TO DO The steering column remains locked. Steering wheel locked. Move the steering wheel while pressing the engine start button (refer to the information on “Starting the engine” in Section 2). Coolant boiling in the coolant reservoir. Mechanical fault: damaged cylinder head gasket. Stop the engine. Contact an approved dealer. Smoke under the bonnet. Short-circuit or cooling system leak.
Operating faults (4/5) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine overheats. The coolant temperature indicator is in the warning zone and warning light ® comes on. Engine cooling fan not working. Stop the vehicle, switch off the engine and contact an approved dealer. Coolant leaks. Check the coolant reservoir: it should contain fluid. If there is no coolant, consult an approved dealer as soon as possible.
Operating faults (5/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer. Direction indicators flashing more quickly. Blown bulb. Front: contact an approved dealer. The direction indicators do not work. Faulty electrical circuit. Consult an approved dealer.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2 Engine identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 Engine specifications. . .
Vehicle identification plates A A 1 2 3 4 5 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. The presence and location of the information depends on the vehicle. Vehicle identification plate A B 6 7 8 9 10 1 Vehicle type and chassis number. Depending on the vehicle, this information is also given on marking B. 2 MMAC (Maximum permissible all-up weight). 11 12 13 3 GTW (Gross train weight – vehicle fully loaded, with trailer).
Engine identification plates A 1 2 A 3 A Quote the information on the identification plate or label A in all correspondence or when ordering parts. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number. 3 A A 6.
Dimensions (in metres) 1.014 2.756 0.925 1.557 4.695 1.445* 1.512 2.060 * Unladen 6.4 ENG_NU_936-3_BK91_Renault_6 Dimensions dimensions............................................ (up to the end of the DU) technical specifications..........................
Dimensions (in metres) (continued) 1.014 2.756 1.031 1.557 4.801 1.445* 1.512 2.060 * Unladen 6.
Engine specifications Versions 2.0 16V 2.0T 1.5 dCi 2.0 dCi Engine type (see engine plate) M4R F4R Turbo K9K M9R Cubic capacity (cc) 1 995 1 998 1 461 1 995 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer.
Replacement parts and repairs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
Service sheets VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp □ Service Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp □ Service Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp □ Service Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Service Comments/miscellaneous □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
Anticorrosion check If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15 ENG_NU_936-3_BK91_Renault_6 Anticorrosion check anti-corrosion check..............................
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Alphabetical index (1/5) A ABS........................................................................2.22 → 2.26 accessories........................................................................ 5.28 accessories socket............................................................. 3.21 additional methods of restraint......................1.22 → 1.25, 1.28 side protection.............................................................. 1.27 to the rear seat belts.........................................1.
Alphabetical index (2/5) driving position settings......................................................................... 1.19 E electric beam height adjustment......................................... 1.68 electric windows.....................................................3.11 → 3.13 electronic parking brake.........................................2.12 → 2.14 Electronic Stability Program: ESP..........................2.22 → 2.26 emergency brake assist.........................................2.22 → 2.
Alphabetical index (3/5) I indicators................................................................... 1.64, 5.12 indicators: direction indicators............................................... 1.64, 5.15 exterior temperature indicator....................................... 1.61 instrument panel...............................................1.45 → 1.51 instrument panel............................................1.45 → 1.59, 1.65 instrument panel messages...................................1.52 → 1.
Alphabetical index (4/5) reference......................................................................... 6.2 parking distance control.........................................2.34 → 2.36 power-assisted steering..................................................... 1.44 puncture..............................................................5.2, 5.6 → 5.8 R radio................................................................................... 3.34 fitting a radio.............................................
Alphabetical index (5/5) trims...................................................................................... 5.6 trip computer and warning system... 1.45 → 1.48, 1.50 → 1.59 tyre inflation kit...........................................................5.3 → 5.5 tyre pressure........................................2.19 → 2.21, 4.11, 5.10 tyre pressure monitor.............................................2.19 → 2.21 tyre pressures..................................................................... 4.
( www.e-guide.renault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
